iRobot Verro 100 Owners Manual

iRobot Verro 100 Manual

Get iRobot Verro 100 PDF manuals and user guides View all iRobot Verro 100 manuals
Add to My Manuals
Save this manual to your list of manuals

iRobot Verro 100 manual content summary:

  • iRobot Verro 100 | Owners Manual - Page 1
    iRobot® Verro™ Owner's Manual Model 100 1.877.855.8593
  • iRobot Verro 100 | Owners Manual - Page 2
    the cleaner from the water. Do not plug-in the Power Supply within 12 feet of the pool. Do not leave the cleaner in the pool all the time. Mishandling of the unit can result in leakage of lubricants. Please keep the plug and power supply away from contact with water.  iRobot Verro Owner's Manual
  • iRobot Verro 100 | Owners Manual - Page 3
    - not the floating power cord - to remove Verro from the pool. Using the power cord can severely damage the robot. Do not force the floating power cord plug. It will fit into the socket only one way. Do not leave your cleaner in direct sunlight when not in use. Never leave the Power Supply in direct
  • iRobot Verro 100 | Owners Manual - Page 4
    Power Supply OFF and then back ON and then press the reset button. Tip Periodically, clean filter bag using cold water only on gentle cycle. Never use detergents, fabric softeners, bleach or other additives and do not machine dry. This will cause permanent damage to your filter bag.  iRobot Verro
  • iRobot Verro 100 | Owners Manual - Page 5
     Table of Contents Anatomy and Parts List 6 - 7 How Verro Works 8 Using Verro 9 - 11 Adjusting the Locking Pin 12 - 14 Cleaning the Filter Bag 15 - 17 Maintenance and Adjustment 18 - 22 Troubleshooting 23 - 25 Customer Care 26 www.irobot.com 
  • iRobot Verro 100 | Owners Manual - Page 6
    19 Parts List 1. Xmas Tree 2. Wheel 3. Washer 4. Side Plate 5. Screw 6. Axle 7. Locking Pin 8. Body 9. Transformer 10. Floating Power Cord 11. Screw 12. Jet Valve 13. Filter Screen 14. Motor 15. Lock Tab 16. Nut 17. Wheel Tube 18. Filter Bag 19. Bottom Lid Assembly  iRobot Verro Owner's Manual
  • iRobot Verro 100 | Owners Manual - Page 7
     Jet Valve Housing Assembly 16 15A 15 15. Jet Valve Port 15A. Jet Valve Port Screw 16. Jet Valve Housing Time Control Dial Rear View 1. Fuse Holder 2. Power Supply cord Front View 3 4 3. Power (ON/OFF) Switch 4. Socket (For Floating Power Cord) www.irobot.com 
  • iRobot Verro 100 | Owners Manual - Page 8
    the water being pumped through the robot to hold itself against the surface it is cleaning and to move along it. Each time it changes direction, Verro automatically alters it course slightly so that it covers the entire bottom of the pool efficiently and systematically.  iRobot Verro Owner's Manual
  • iRobot Verro 100 | Owners Manual - Page 9
    at least 12 feet from the pool and that the power switch is OFF. Plug the Power Supply into a GFCI outlet. Ensure the electric outlet has been properly grounded. Never leave the Power Supply plugged in when Verro is not in use Warning: A Ground Fault Current Interrupter (GFCI) must be installed
  • iRobot Verro 100 | Owners Manual - Page 10
    ON. The light on the Power Supply will illuminate and Verro will start to clean your pool. 7 After approximately two hours, Verro will stop and the Power Supply light will turn off. To stop Verro before the end of the cleaning cycle, switch the Power Supply OFF. 10 iRobot Verro Owner's Manual
  • iRobot Verro 100 | Owners Manual - Page 11
    removing the cleaner from the pool. 9 Unplug the Power Supply from the GFCI outlet. Never leave the Power Supply plugged in when Verro is not in use. 10 Unplug the floating power cord from the Power Supply. 11 Use the floating power cord to pull Verro to the edge of the pool, then use the handle
  • iRobot Verro 100 | Owners Manual - Page 12
     Adjusting the Locking Pin The Locking Pin has two purposes: Help Verro clean with the most optimal cleaning pattern for your pool, keep the power cord from tangling after repeated uses. To keep the power cord from becoming kinked and tangled, always reverse the position of the locking pin to the
  • iRobot Verro 100 | Owners Manual - Page 13
    turn in a counter clockwise movement in this direction Maneuverable Axle (Pin in rear preset position) Goes straight in this direction Fixed Axle Cleaning Pattern 1 In preset rear position, the unit will move straight then reverse at a slight arc and continue in this pattern to systematically
  • iRobot Verro 100 | Owners Manual - Page 14
    , the next time you use your robot, it will clean in the opposite direction of the prior use. This will ensure complete cleaning of your pool and reduce the ability of In forward position the robot will move straight then reverse at a greater arc Cleaning Pattern 2 14 iRobot Verro Owner's Manual
  • iRobot Verro 100 | Owners Manual - Page 15
    the floating power cord from the Power Supply, and remove Verro from the pool. Please keep the plug away from water. 2 Place Verro upside down on a towel (to prevent scratches). 3 Unlock and remove the bottom panel by pushing the two locking tabs toward the sides of the robot. www.irobot.com 15
  • iRobot Verro 100 | Owners Manual - Page 16
    all visible dirt, machine wash the bag using cold water on the gentle cycle. Important: Do not use detergents, fabric softeners, bleach or other support bars. Be sure to position the bag centrally on either long portion of bottom lid assembly for proper fit. 16 iRobot Verro Owner's Manual
  • iRobot Verro 100 | Owners Manual - Page 17
     Cleaning the Filter Bag (cont...) 8 Replace filter bag assembly in the robot. 9 Reinsert the bottom lid assembly. Make sure the lock tabs click into place and no portion of the filter bag is sticking out. www.irobot.com 17
  • iRobot Verro 100 | Owners Manual - Page 18
    between 50 and 104 degrees Fahrenheit. Temperatures below freezing (≤ 32° F) may damage pump motor. The Power Supply is water resistant, but not waterproof and may be damaged by rain. Important: Failure to properly store Verro will result in loss of warranty. 18 iRobot Verro Owner's Manual
  • iRobot Verro 100 | Owners Manual - Page 19
    on the surface of the water, it may be necessary to untwist it using the Detangler. 1 Unplug the Power Supply. (Please keep the plug away from contact with water.) Unplug the floating power cord from the Power Supply. 2 Place the robot perpendicular to you so that you can walk away from it for 50
  • iRobot Verro 100 | Owners Manual - Page 20
    the motor. If you notice that Verro is not cleaning well or that it is having difficulty moving around the pool, and other measures (cleaning the filter bag, checking the vacuum intakes, etc.) have not corrected the problem, check the Propeller. 1 Unplug the Power Supply. (Please keep the plug away
  • iRobot Verro 100 | Owners Manual - Page 21
     Maintenance and Adjustment (cont...) Cleaning the Propeller (cont...) 6 Using the bent paper clip, hook the material fouling the Propeller. It may be helpful to use a small flashlight to see better. 7 Replace the jet valve port. 8 Replace the screws. But do not overtighten. www.irobot.com 21
  • iRobot Verro 100 | Owners Manual - Page 22
    There is a flap just inside each vacuum intake at the bottom of the robot. These flaps must freely open and close. If they do not, remove any dirt or debris that is interfering with their operation. Cleaning the Direction Flap Verro uses a flap to redirect the flow of water so that it can move
  • iRobot Verro 100 | Owners Manual - Page 23
    " for bag cleaning instruction. If you find the fine filter bag gets clogged too quickly (e.g. you have significant amounts of larger debris), consider a mesh bag instead. Always turn off Verro's Power Supply and unplug it before troubleshooting any problem. Problem likely Cause Verro moves The
  • iRobot Verro 100 | Owners Manual - Page 24
     Troubleshooting (cont...) Problem Verro reverses direction before reaching end of pool or Verro waits too long at side of pool before changing direction Likely Cause The filter bag needs to be cleaned Flaps in the vacuum intakes at bottom of robot are blocked Wheels or axles are not turning
  • iRobot Verro 100 | Owners Manual - Page 25
    19) Verro will not start a Reset required cleaning cycle Turn Power Supply OFF and then back ON. Press reset button. Verro is not plugged into the Power Supply Plug Verro into the Power Supply. The Power Supply is not Plug the Power Supply into GFCI outlet only. plugged in www.irobot.com 25
  • iRobot Verro 100 | Owners Manual - Page 26
    .855.8593. To ensure that your call is guided to a Verro Support Technician, be sure to listen closely and follow the prompts for iRobot Verro Pool Product Technical Support. Failure to follow the prompts may lead to longer response times. iRobot Verro Customer Care Hours: Hours of operation vary by
  • iRobot Verro 100 | Owners Manual - Page 27
  • iRobot Verro 100 | Owners Manual - Page 28
    ™ today. SAVE 15% on all accessories.* Optional Accessories for Verro 100: Fine Filter Bag Mesh Filter Bag To purchase accessories: Call 800.727.9077 or visit our website at store.irobot.com *See registration card for details. Pricing and availability subject to change. Shipping and handling not
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
iRobot
®
Verro
™
OWNER’S MANUAL
Model 100
1.877.855.8593