2008 Ducati Hypermotard 1100 Owners Manual

2008 Ducati Hypermotard 1100 Manual

Get 2008 Ducati Hypermotard 1100 PDF manuals and user guides View all 2008 Ducati Hypermotard 1100 manuals

2008 Ducati Hypermotard 1100 manual content summary:

  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 1
    Owner's manual E 1100S / 1100 1
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 2
    E 2
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 3
    you smooth and enjoyable riding. We are steadily doing our best to improve our "Technical Assistance" service. For this reason, we recommend you to strictly follow the indications given in this manual, especially for motorcycle running-in. In this way, your Ducati motorbike will surely give you
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 4
    Table of contents RH switch 43 Throttle twistgrip 43 Front brake lever 44 Rear brake pedal 45 Gear change pedal 45 Setting the gear change and rear brake pedals 46 Main components and devices 48 E General 6 Warranty 6 Symbols 6 Useful information for safe riding 7 Carrying the maximum load
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 5
    Main maintenance operations 68 Removing the fairing 68 Checking brake and clutch fluid level 70 Checking brake pads for wear 72 Lubricating joints 73 Adjusting throttle control free play 74 Charging the battery 75 Checking drive chain tension 76 Chain lubrication 77 Replacing the headlight bulbs 78
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 6
    motorcycle unchanged for a long time. This manual contains some special remarks: E Warranty Warning Failure to comply with these instructions may put you at risk and lead to staff have access to the implements required to perform any servicing job at best, and use Ducati original spare parts only
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 7
    Useful information for safe riding Warning Read this section before riding your motorcycle. Accidents are frequently due to inexperience. Always make sure you have your licence with you when riding; you need a valid licence to be entitled to ride your motorcycle. Do not lend your motorcycle to
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 8
    riding, carrying the maximum load allowed in full safety. Even weight distribution is critical to preserving these safety features and avoiding trouble when performing sudden manoeuvres or riding on bumpy roads. Information about carrying capacity The total weight of the motorcycle in running
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 9
    Arrange your luggage or heavy accessories in the lowest possible position and close to motorcycle centre. Be sure to secure the luggage to the supports provided on the motorcycle as firmly as possible. Improperly secured luggage may affect stability. Never fix bulky or heavy objects to the handlebar
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 10
    Identification data All Ducati motorcycles have two identification numbers, for frame (fig. 1) and engine (fig. 2). Frame number Engine number E Note These numbers identify the motorcycle model and should always be indicated when ordering spare parts. fig. 1 fig. 2 10
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 11
    Controls 4 1 8 Warning This section details the position and function of all the controls you need to drive your motorcycle. Be sure to read this information carefully before you use the controls. E 3 7 Position of motorcycle controls (fig. 3) 1) 2) 3) 4) 5) 6) 7) 8) 9) Instrument panel. Key-
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 12
    Instrument panel (fig. 4) 1) LCD, (see page 14) 2) Revolution counter (rpm). Shows the engine rotation speed/minute. 3) Neutral light N (green). Comes on when in neutral position. 4) Fuel warning light (yellow). Comes on when there are about 3 litres of fuel left in the tank. 5) Indicators repeater
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 13
    10) Button A/B. Button used to display and set instrument panel parameters. It has two positions: A "s" and B "t". 11) High-beam flasher button FLASH (fig. 5) The high-beam flasher button may also be used to control the LAP functions and the instrument panel USB data logger. A 10 11 E B fig. 5 13
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 14
    LCD unit functions Warning Stop the motorcycle before using the instrument panel controls. Never operate the instrument panel controls while riding. 1) Speedometer. Gives road speed 2) Odometer. Gives total distance covered. 3) Trip meter. This function indicates the distance covered since the meter
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 15
    warning (fig. 6). This indicator comes on to indicate that the vehicle is due for service. It stays on until it is reset at an Authorised Ducati Workshop as part of the service procedure. 11) LAP /USB function (fig. 6). Indicates when the USB data logger and the LAP function are on. Important
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 16
    LCD - Parameter setting/display When the key is turned from OFF to ON, the Dashboard turns on all LCD digits for one second and all warning lights one by one. It then switches to "normal" display mode showing the model indication in place of the odometer readout and the version (EU, UK, USA, CND,
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 17
    Upon Key-On, the Dashboard always displays the following information (and any functions activated previously are deactivated): Odometer Speed Engine rpm With the button (1, fig. 8) set to B "t", the Odometer readout will cycle through the following functions: TRIP TRIP FUEL (only if active) Clock T.
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 18
    Total distance covered indicator: "Odometer" This function shows the total distance covered by the vehicle. Upon Key-On, the system automatically enters this function. The odometer reading is stored permanently and cannot be reset. When the reading reaches 99999 Km (or 99999 mi), "99999" is
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 19
    "TRIP" meter This function shows the distance travelled since the Trip meter was last reset. Holding button (1, fig. 8) pressed in position B "t" for 3 seconds when this function is displayed resets the trip meter. When the reading exceeds 999.9, distance travelled is reset and the meter
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 20
    Distance travelled on fuel reserve: "TRIP FUEL" This function shows the distance travelled on fuel reserve. When the fuel light comes on, the display automatically switches to the TRIP FUEL indicator. Trip fuel reading remains stored even after Key-Off until the vehicle is refuelled. Count is
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 21
    Engine coolant temperature indicator It shows engine coolant temperature: Important This indication is only active when the engine is running. - If reading is -40 °C (°F -104) or less, the display shows a string of flashing dashes ("---") and the Diagnostic light (EOBD) (8, fig. 4) comes on; - if
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 22
    ). Indicator ( ) comes on to indicate that the vehicle is due for service. The display shows the service reminder at the following intervals: when the odometer reaches 1000 Km; every 12,000 Km. The indication remains displayed until it is reset. When the
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 23
    Battery voltage indicator (BATT) This function provides battery voltage indication. To view this function, access the menu and enter the "BATT" page. The instrument panel display shows battery voltage indication as follows: - if voltage is between 12.1 and 14.9 Volt, the reading is on steady; - if
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 24
    Engine idle RPM indication (RPM) This function digitally displays engine idle rpm. To view this function, access the menu and enter the "RPM" page. In addition to the rev counter scale at the top, the instrument panel display shows engine rpm as a numeric value for improved accuracy when setting
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 25
    LAP timer This function lets you display lap times. To enable this function, enter the menu and set the "LAP" function to "On" by holding button (1, fig. 8) pressed in position B "t" for 3 seconds. Once you have set the LAP function to On, exit the menu (press A for 3 seconds); the system will exit
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 26
    E When the LAP function is set to Off in the menu, the current "lap" is not stored. The LAP function is disabled automatically if the key is turned to Off (Key-Off) while it is active and the current "lap" is not stored even though the lap timer had been active before Key-Off. If the lap timer is
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 27
    Stored data display (LAP Memory) Displays data stored using the LAP function: lap number and lap time. To view stored lap times, enter the menu and go to page "LAP MEM". In this menu page, press button (1, fig. 8) in position B "t" to view the "1st lap"; the display will show lap number and lap time
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 28
    E USB data logger This function lets you activate the USB data logger, the data logger must be connected to vehicle wiring. To enable the data logger, enter the menu and set the "LAP" function to "On" by holding button (1, fig. 8) pressed in position B "t". The START/STOP control for the data
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 29
    Clock setting function To set the clock, enter the menu page "TIME Set". Holding button (1, fig. 8) pressed in position B "t" for 3 seconds in this menu page gives access to the setup mode. When you access this function, the word "AM" flashes; pressing button (1, fig. 8) in position B "t" switches
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 30
    Instrument panel diagnostics Warning When an error is displayed, always contact an authorised Ducati workshop. Important The instrument panel runs system diagnostics after 60 seconds from the last Key-Off. Any abnormal vehicle behaviour is displayed. If more errors are present, they are displayed
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 31
    Warning light Error message INJE PUMP STRT STRT STEP. STEP. STEP. LAMB. LAMB. EXVL EXVL EXVL 13.2 16.0 19.1 19.2 21.1 21.2 21.3 22.1 22.2 23.1 23.2 23.3 Error Vertical cylinder injector error Fuel pump relay error Solenoid starter error Solenoid starter error Stepper motor error Stepper motor
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 32
    Warning light Error message EXVL EXVL TPS 23.4 23.5 1.1 1.2 2.1 2.2 3.1 3.2 4.1 4.2 5.1 5.2 Error Exhaust butterfly valve motor error Exhaust butterfly valve motor error Throttle position sensor error Throttle position sensor error Pressure sensor error Pressure sensor error Engine oil temperature
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 33
    Warning light Error message LAMB TILT ECU PK.UP SPEE. IMMO IMMO IMMO IMMO CAN 6.1 6.2 30.0 34.0 36.0 37.0 37.1 37.4 37.5 38.0 Error Lambda sensor error Lambda sensor error 2 Generic Engine Control Unit error Pick-up sensor error Speed sensor error Immobilizer error Immobilizer error Immobilizer
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 34
    E Headlight "smart" auto-off This function allows you to reduce current consumption from the battery, by automatically managing headlight switchingoff. The device is enabled in three instances: - When the key is turned from OFF to ON and the engine is not started within 60 seconds, the headlight is
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 35
    keys have a small plate (1) attached that reports their identification number. E Note Your Ducati dealer might ask you to submit the Code Card for some service operations. The black keys (B) are regular ignition keys and are used to: - start up the engine - open the lock of the fuel tank filler
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 36
    described below. This procedure lets you disable the "engine block" function - indicated by the amber EOBD light (8, fig. 4) coming on - in the event of problems with the immobilizer system. But this operation can be carried out only if the electronic code indicated on the code card is known. fig
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 37
    Immobilizer override procedure In the event of an "Immobilizer BLOCK", you will have to enter the 5-digit electronic card reported on the Code Card before you can perform the "Immobilizer override procedure" from the instrument panel; enter the corresponding function as described below: Enter the
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 38
    E Entering the code: when you access this function, the first digit on the left will flash. Button (1, fig. 8): each time you press the button in position B "t", the digit will increase by one unit per second; if you press the button in position A "s", you will move to the second digit, which will
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 39
    . If the other key does not work out either, contact the DUCATI Service network. Duplicate keys If you need any duplicate keys, contact the DUCATI Service network with all the keys you have left and your CODE CARD. DUCATI Service will program new keys and re-program your original keys. You may be
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 40
    Key-operated ignition switch and steering lock (fig. 25) It is located in front of the fuel tank and has four positions: A) B) C) D) ON: lights and engine on; OFF: lights and engine off; LOCK: steering locked; P: parking light on, steering locked. B A C D Note E To move the key to the last two
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 41
    LH switch (fig. 26) 1) Dip switch, light dip switch, two positions: position = low beam on; position = high beam on. 2) Switch = 3-position turn indicator: centre position = OFF; position = left turn; position = right turn. To cancel turn indicators, push in once switch returns to central position.
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 42
    Clutch lever (fig. 27) 2 3 E Lever (1) disengages the clutch. It features a dial adjuster (2) for lever distance from the twistgrip on handlebar. To adjust, keep lever (1) completely extended, turn knob (2) and set it to one of the four available positions. Remember that: position no. 1 gives
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 43
    RH switch (fig. 28) 1) ENGINE STOP switch, two positions: - position (RUN) = run. - position (OFF) = stop. 1 3 Warning This switch is mainly intended for use in emergency cases when you need to stop the engine quickly. After stopping the engine, return the switch to the position to enable
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 44
    Front brake lever (fig. 29) Pull in the lever (1) towards the twistgrip to operate the front brake. The system is hydraulically operated and you just need to pull the lever gently. The control lever features a dial adjuster (2) for lever distance from the twistgrip on handlebar. To adjust, keep
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 45
    Rear brake pedal (fig. 30) Push down on the pedal (1) to apply the rear brake. The brake is hydraulically controlled and operation requires minimum effort. 1 E fig. 30 Gear change pedal (fig. 31) When released, the gear change pedal automatically returns to rest position N in the centre; this is
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 46
    Setting the gear change and rear brake pedals The gear change and rear brake pedals can be adjusted to suit the preferred riding position of each rider. Adjust the pedals as follows: Gear change pedal (fig. 32) Apply an open-end wrench to the flats (2) to lock out linkage (1) rotation and loosen the
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 47
    Rear brake pedal (fig. 33) Loosen check nut (5). Turn pedal travel adjusting screw (6) until pedal is in the desired position. Tighten check nut (5). Work pedal by hand to make sure it has 1.5 - 2 mm free play before brake begins to bite. If not so, set the length of cylinder linkage as follows.
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 48
    Main components and devices 6 8 E Position on the vehicle (fig. 34) 1) 2) 3) 4) 5) 6) 7) 8) 9) Tank filler plug Seat. Glove compartment door. Side stand. Front fork adjusters. Rear shock absorber adjusters. Rear-view mirrors. Silencer and exhaust pipes. Catalytic converter. 3 7 5 4 9 2 8
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 49
    Fuel tank plug (fig. 35) Opening Insert the key into the lock. Turn the key clockwise 1/4 turn to unlock. Unscrew the plug (1, fig. 35). Closing Tighten the plug (1) with the key inserted and push it down into its seat. Turn the key counter clockwise to its initial position and take it out. 1 E
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 50
    Opening Unscrew the screw (1) with the supplied Allen wrench and remove it. Raise the rear end of the seat and slide it off the front supports in a rearward motion. Closing Slide the front ends of the seat bottom underneath the frame U-bolt, start the screw (1) in its hole and tighten. Ensure
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 51
    Opening the glove compartment door To access the glove compartment, turn the plastic screws (1) counter clockwise by one fourth of a turn. Remove the inner door to access the glove compartment; it contains the tool kit (see page 67). 1 Important Do not store heavy or metal parts in the glove
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 52
    is fully extended. Lean the motorcycle to the left until the stand contacts the ground. Warning Do not sit on the motorcycle when it is supported on the side stand. To move the side stand to its rest position (horizontal position), lean the motorcycle to the right while lifting the thrust
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 53
    Front fork adjusters The front fork used on this motorcycle has rebound, compression and spring preload adjustment. This adjustment is done using the outer adjusters: 1) to adjust rebound damping (fig. 40 and fig. 41); 2) to adjust spring preload (fig. 40 and fig. 41); 3) to adjust compression
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 54
    This will be your starting point. Now turn the adjuster counter clockwise and listen for the clicks that identify setting positions no. 1, 2 and so on. STANDARD factory setting is as follows: 1100S compression: 1.5 turns ± 1/4 of a turn; rebound: 1.5 turns ± 1/4 of a turn. Spring preload: 10 mm (
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 55
    Rear shock absorber adjusters (fig. 43 and fig. 44) The rear shock absorber has outer adjusters that enable you to adjust your motorcycle to the load. The adjuster (1) on the right side of the connection holding the shock absorber to the swinging arm controls rebound damping. The adjuster (2) on the
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 56
    Rear-view mirror adjustment Loosen ring nut (A) to adjust. Move the rear-view mirror body (B) to the desired position and tighten the ring nut (A) to lock the mirror in position. LOOSENS A B Warning Never push on the mirror centrally to adjust its position or it might break off. TIGHTENS E fig.
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 57
    Changing motorcycle track alignment (1100S) Motorcycle track alignment is the result of tests carried out under different riding conditions by our technical staff. Modifying factory setting is a very delicate operation, which may lead to serious damages if carried out by unskilled people. Before
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 58
    UNIBALL articulated head (A) maximum extension is 5 threadings, i.e. 7.5 mm (B). B E A fig. 48 58
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 59
    Directions for use For the first 100 km, use the brakes gently. Do not brake violently or keep brake applied for too long. This will enable a correct break-in of friction material on brake pads against brake discs. For all mechanical moving parts to adapt to one another and above all not to
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 60
    Important During the whole running-in period, the maintenance and service rules recommended in the Warranty Card should be observed carefully. Failure to comply with these rules will release Ducati Motor Holding S.p.A. from any liability whatsoever
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 61
    Pre-ride checks Warning Failure to carry out these checks before riding, may lead to motorcycle damage and injury to rider and passenger. Before riding, perform a thorough check-up on your bike as follows: Fuel level in the tank Check fuel level in the tank. Fill tank if needed (page 66). Engine oil
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 62
    Starting the engine Warning Before starting the engine, become familiar with the controls you will need to use when riding (see page 11). 1) Move the ignition key to ON (fig. 50). Make sure the green light N (8, fig. 4) and the red light (7, fig. 4) on the instrument panel are on. PUSH ON FF ON O
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 63
    2) Check that the stop switch (1, fig. 51) is positioned to (RUN), then press the starter button (2). This model is equipped with a servoignition system. To achieve assisted engine starting, press the button (2) and release it immediately. Pressing the button (2) operates automatic engine starting
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 64
    Moving off 1) Disengage the clutch squeezing the control lever. 2) Push down on gear change lever sharply with the tip of your foot to engage the first gear. 3) Speed up engine, by turning the throttle twistgrip and slightly releasing the clutch lever at the same time; the motorcycle will start
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 65
    Stopping the motorcycle If you let go of the throttle twistgrip, the motorcycle will slow down gradually and smoothly. Then, shift down releasing the clutch, and finally change from first to neutral. Apply brakes and you will bring the motorcycle to a complete stop. To switch the engine off, simply
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 66
    Refuelling (fig. 50) Never overfill the tank when refuelling. Fuel should never be touching the rim of filler recess. Max level Warning Use low-lead fuel with 95 octane rating at origin minimum (see "Top-ups" table, page 95). Be sure there is no fuel trapped in the filler recess. E fig. 50 66
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 67
    Tool kit and accessories (fig. 51) The compartment in the left fairing can be accessed after opening the inner door (see page 51) and contains: the tool kit, which includes : - Box wrench for spark plugs. - Tommy bar for plug wrench; - double-tip screwdriver; - 3-mm Allen wrench; - 4-mm Allen wrench
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 68
    Main maintenance operations E Removing the fairing Warning Some servicing operations need the motorcycle fairing to be removed. Failure to refit or correctly install any one of the parts you have removed may result in
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 69
    Right side body panel Lift the seat (page 50) Unscrew the three screws (1) securing the baffle (2). Remove the baffle (2). Unscrew the three screws (3) and remove the side body panel (4). 2 1 E fig. 54 4 3 3 fig. 55 69
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 70
    Checking brake and clutch fluid level Fluid level should never fall below the MIN mark on each reservoir (fig. 56 and fig. 57). If level drops below the limit, air might get into the circuit and affect the operation of the system involved. Brake and clutch fluid must be topped up and changed at the
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 71
    Clutch system (fig. 57) If the control lever has exceeding play and the transmission snatches or jams as you try to engage a gear, it means that there might be air in the circuit. Contact your Ducati Dealer or Authorised Workshop to have the system inspected and air drained out. (MAX) 3 mm Warning
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 72
    Checking brake pads for wear (fig. 58) Front brake pads have a wear mark to facilitate inspection without removing the pads from the callipers. If the grooves in the friction material are still visible, the pad is still in good condition. The rear brake pads must be replaced when friction material
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 73
    inside the sheaths: if you feel any friction or jamming, have the cable replaced by a Ducati Dealer or Authorised Workshop. To avoid this kind of problem, unscrew the two retaining screws (1, fig. 60) to open the case and then grease cable ends and pulley with SHELL Advance Grease or Retinax LX2
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 74
    Adjusting throttle control free play The throttle twistgrip must have a free play of 1.5 - 2 mm measured at the edge of the twistgrip, at all positions of the handlebars (fig. 62). If not so, free play can be adjusted by means of the throttle body adjusters (1) (fig. 63). 1,5 ÷ 2 mm 1,5 ÷ 2 mm
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 75
    Charging the battery (fig. 64) Before charging the battery, it is best to remove it from the motorcycle. Remove the seat (see page 50). Disconnect the black negative terminal (-) and the red positive terminal (+) in the order. Unscrew the two retaining screws (1) from the battery mounting brackets
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 76
    Checking drive chain tension (fig. 65) Wheel the motorcycle back and forth until finding the position at which the chain is tightest. Place the motorcycle on the side stand. Place the rule in front of the chain guard, push down on the chain and release it. Tension up until the distance between the
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 77
    Chain lubrication The chain fitted on your motorcycle has O-rings that keep dirt out of and lubricant inside the sliding parts. The seals might be irreparably damaged if the chain is cleaned using any solvent other than those specific for O-ring chains or washed using steam or water cleaners. After
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 78
    (page 102). Always test the new lamp before refitting the parts you have removed. Unscrew the screws (1) with an Allen wrench. Ease off the headlight support towards the front until releasing the handgrip (2). Unscrew the handgrip (2) turning counter clockwise. E 1 fig. 67 2 fig. 68 78
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 79
    Release the clip (3). The bulb (4) has a bayonet base: press and twist counter clockwise to remove. Fit the spare bulb by pressing and turning clockwise until it clicks. 3 Note Be careful to hold the new bulb at the base only. Never touch the transparent body with your fingers or it will blacken
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 80
    Replacing the rear turn indicator bulbs To change the rear turn indicator bulbs, loosen the screw (1) and remove the cup (2). E 2 1 fig. 71 80
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 81
    Replacing the number plate light bulbs Remove the grommet (1) and extract the bulb. 1 E fig. 72 81
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 82
    Beam setting (fig. 73) When checking beam setting, put the motorcycle upright. Tyres should be inflated at the correct pressure and one person should be sitting astride the motorcycle, keeping it at right angles to its longitudinal axis. Place the motorcycle opposite a wall or a screen, 10 meters
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 83
    Beam adjustment (fig. 74) Turn the screw (1) to set beam height. The side position of the headlamp is adjusted using the screw (2). 1 2 Note Remove the lower headlight fairing to give access to the headlamp adjusting screws. Important The adjusting screws (1) and (2) have no end stop. E fig. 74
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 84
    Tubeless tyres Front tyre pressure: 2.2 bar Rear tyre pressure: 2.2 bar Tyre repair or change (Tubeless tyres) In the event of a tiny puncture, tubeless tyres will take a long time to deflate, as they tend to keep air inside. If you find low pressure on one tyre, check the tyre for punctures.
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 85
    Minimum tread depth Measure tread depth (S, fig. 75) at the point where tread is most worn down. It should not be less than 2 mm and anyway not below the legal limit. S Important Visually inspect the tyres at regular intervals for cracks and cuts, especially on the side walls, bulges or large
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 86
    Checking engine oil level (fig. 76) Engine oil level can be checked through the sight window (1) on the clutch cover on the RH side of the engine. Oil level must be checked with the motorcycle perfectly upright and the engine cold. Oil level should be between the marks near the sight glass. Top up
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 87
    Cleaning and replacing the spark plugs (fig. 77) Spark plugs are essential to smooth engine running and should be checked at regular intervals. This operation also provides an indication of engine condition. Have the spark plugs checked and replaced (as required) by a Ducati Dealer or Authorised
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 88
    Cleaning the motorcycle To preserve the finish of metal parts and paintwork, wash and clean your motorcycle at regular intervals, anyway according to the road conditions you ride in. Use specific products only. Prefer biodegradable products. Avoid aggressive detergents or solvents. Warning Braking
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 89
    , then crank the engine by hand a few times so a protective film of oil will spread on cylinder inner walls; place the motorcycle on a service stand; remove the battery and keep it well charged and efficient. Battery should be checked and charged (or replaced, as required) whenever the motorcycle
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 90
    Maintenance Scheduled maintenance chart: operations to be performed by the dealer E Km. x1000 List of operations and type of intervention [set mileage (km/mi) or time interval *] Change engine oil Change engine oil filter Clean engine oil filter at intake Check engine oil pressure Check and/or
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 91
    Km. x1000 List of operations and type of intervention [set mileage (km/mi) or time interval *] Check brake and clutch fluid level Change brake and clutch fluid Check and adjust brake and clutch controls Check/lubricate throttle / cold start controls Check tyre pressure and wear Check brake pads.
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 92
    test of the motorcycle mi. x1000 Months 1 0.6 6 12 7.5 12 24 15 24 36 22.5 36 48 30 48 60 37.5 60 • E Cleaning the motorcycle * Service on the set interval, whichever comes first (mileage or months) (1) Operation to be performed only if set mileage (km/mi) is reached 92
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 93
    brake and clutch fluid level Check tyre pressure and wear Check chain tension and lubrication Check brake pads. If necessary, have it changed by a dealer * Service on the set interval, whichever comes first (mileage or months) 1 0.6 6 E 93
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 94
    Technical data E Overall dimensions (mm) (fig. 78) Weights Dry weight in running order without fuel: 179 Kg. 177 Kg. (S) Carrying full load: 390 Kg. 1455 ± 20 2120 ± 20 900 ± 20 Warning 1150 ± 20 Failure to observe weight limits could result in poor handling and impair the performance of your
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 95
    Top-ups Fuel tank, including a reserve of 3.3 cu dm (litres) Lubrication circuit Clutch and front/rear brake systems Protectant for electric contacts Front fork Type of fluid Unleaded fuel with 95 fuel octane rating (at least) SHELL - Advance Ultra 4 Special fluid for hydraulic systems SHELL
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 96
    Engine 1100 cc 90º longitudinal "L" twin-cylinder four-stroke Desmodromic engine, electronic fuel injection, air cooling. Bore: 98 Stroke: 71.5 Total displacement, cu. cm: 1078 Compression ratio: 10.5 ± 0.5:1 Max. power at crankshaft (95/1/EC): 61.2 kW - 83.2 HP at 7500 rpm Max crankshaft torque (95
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 97
    Performance data Maximum speed in any gear should be reached only after a correct running-in period with the motorcycle properly serviced at the recommended intervals. Exhaust system Equipped with catalytic converter in compliance with EURO 3 emission regulations. Spark plugs The ignition system
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 98
    trials, you may refer to Ducati Motor Holding S.p.A. who will be glad to provide information about the special ratios available. Relevant instructions and original spare parts are available from your local Dealer or Authorised Workshop. Warning If the rear chain sprocket needs replacing, contact
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 99
    Brakes Front Semi-floating drilled twin-disc. Housing material: steel. Braking surface material: steel Disc diameter: 305 mm. Hydraulically operated by a control lever on right handlebar. Braking surface: 84 sq. cm. Brake caliper make: BREMBO Type: 30/34 - 4 pistons. Friction material: FERIT I/D
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 100
    Frame High-strength steel tubular trellis frame. Steering angle (on each side): 32° Steering geometry is as follows: Steering head angle: 24° Trail: 102 mm Tyres Front Tubeless, radial tyre. Size: 120/70-ZR17 Rear Tubeless, radial tyre. Size: 180/55-ZR17 E Wheels Front Five spoke light alloy
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 101
    Suspensions Front Hydraulic upside-down fork provided with outer adjusters for rebound, compression, and preload (for inner springs of fork legs). Stanchion diameter: 50 mm Travel along leg axis: 165 mm Rear Of the progressive type, thanks to a rocker arm connecting frame and upper pivot point of
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 102
    . Tail light with 12V5/21W double-filament bulb for stop light and parking light; 12V-5W bulb for number plate light. E Note For bulb replacement instructions, please read the relevant paragraphs from page 78 onwards. 102
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 103
    Fuses The main fuse box (1, fig. 80) is located under the right side body panel (see page 69). Fuses can be accessed after removing the dust cap. In addition to the main fuse box, there are other fuses at the sides of the battery. A fuse (2, fig. 81) located under the seat protects the fuel
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 104
    A blown fuse is identified by the interrupted centre link (3, fig. 82). Important Switch the ignition key to OFF before replacing a fuse to avoid possible short circuits. 3 3 Warning E Never use a fuse with a rating other than specified. Failure to observe this rule may damage the electric
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 105
    Injection /electric system diagram key 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) 23) 24) 25) 26) 27) 28) 29) 30) Right switch Immobilizer antenna Ignition switch Light relay Fuse box Starter motor Debouncing diode Data logging Fused solenoid starter Battery
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 106
    stop Lights Loads Injection ECU Instrument panel Rat. 10 A 15 A 15 A 20 A 5A 5A Note The system wiring diagram is at the end of this manual. 106
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 107
    it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ducati North America. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 108
    if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. Problems that may affect motorcycle emissions If you are aware of any of the following symptoms, have the vehicle inspected and repaired by your
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 109
    explosive under certain conditions. Refuell in a well ventilated area with the engine stopped. Do not smoke or allow open flames or sparks when refuelling or servicing the fuel system. Always 109
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 110
    E USA close the fuel petcock when the engine is not running to prevent flooding of the throttle body. Do not overfill fuel tank (see instructions page 54). Motorcycle exhaust contains poisonous carbon monoxide gas. Do not inhale exhaust gases and never run the engine in a closed garage or confined
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 111
    Label location (fig. B) 1 5 (only Canada) 2 7 8 6 4 5 E USA 3 fig. B 111
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 112
    Tensione catena (sul cavalletto laterale) Chain tension adjustment (on side stand) 1 2 Cod. 433.1.312.1A 3 E 4 5 USA 7 5 (Only Canada) VEHICLE EMISSION CONTROL LABEL ENGINE DISPLACEMENT :992 cc. ENGINE FAMILY : THIS VEHICLE CONFORMS TO U.S. EPA AND CALIFORNIA REGULATIONS APPLICABLE TO MODEL
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 113
    parts; intake manifold; fuel tank, fuel injection system; spark advance mechanism; crankcase breather; air Important In the event of fuel system malfunction, contact Ducati's authorized Service Centres. E USA 6 3 4 2 5 1 fig. C 113
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 114
    which adversely affect performance and/or (5) use in competitive racing or related events. B. Inspections, replacement of parts and other services and adjustments required for routine maintenance. C. Any motorcycle on which odometer mileage has been changed so that actual mileage cannot be
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 115
    not liable for these parts. The owner is responsible for the performance of all required maintenance. Such maintenance may be performed at a service establishment or by any individual. The warranty period begins on the date the motorcycle is delivered to an ultimate purchaser. Ducati North America
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 116
    Routine maintenance record Km/mi 1,000/600 12,000/7,500 24,000/15,000 Ducati Service Name Mileage Date E USA 36,000/22,500 48,000/30,000 60,000/37,500 116
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 117
    Stampato 03/2007 Cod. 913.7.127.1A Ducati Motor Holding spa via Cavalieri Ducati, 3 40132 Bologna, Italia Tel. +39 051 6413111 Fax +39 051 406580 www.ducati.com
  • 2008 Ducati Hypermotard 1100 | Owners Manual - Page 118
    01 STARTER BW Bk FREE PUSH OFF RUN ENGINE STOP RW RBk 02 LOCK PARK OFF ON 03 Lb WR R GBk GR Y 04 R/Bk O R/B Bn R/Y R/Y 05 1 08 1 2 3 4 06 09 30A Bk Bk 10 11 12 R/W 2 3 4 5 6 7 1 2 B/Bk BK W/B P/Bk R/Y W/Bk 1 2 3 4 R Y/R 07 R/Bk K A R Bk/B Y Y Y 1 4 3 6 2 5 R/W R O Y 49 R R R Bk
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
1
E
Owner’s manual
1100S / 1100