1998 Ford Explorer Owner Guide 1st Printing

1998 Ford Explorer Manual

Get 1998 Ford Explorer PDF manuals and user guides View all 1998 Ford Explorer manuals

1998 Ford Explorer manual content summary:

  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 1
    and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 2
    environmental concerns will follow. Correct driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in. If possible, you should avoid full use of the brakes for the first 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 3
    this Owner's Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Be sure to read Driving off road in the Driving chapter as well as the ''Four Wheeling'' supplement included
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 4
    100 80 60 40 120 H C 2 1 3 UNLEADED FUEL ONLY 80 140 30 20 10 20 H 90 180 0 0 0 0 0 0 160 100 110 200 F E 0 H OFF RSM ON SET ACC OFF COAST SRS Headlamp control (pg. 21) Tilt steering wheel lever (pg. 41) Instrument panel dimmer switch (pg. 22) Turn signal and wiper/washer control
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 5
    ) (pg. 108) OD ON/OFF VOL - PUSH ON AM FM BASS TREB FM 1 CLK BAL FADE AUTO SET PUSH SEEK TUNE DISCS SCAN EJ DOLBY SYSTEM TAPE CD REW 1 FF 2 SIDE 1-2 3 4 COMP 5 SHUFFLE 6 LO OFF HI Climate controls (pg. 43) Foglamp control* (page 21) 5
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 6
    H L H SPEED CONT 4WD HIGH 4WD LOW 20 180 FUEL RESET F E ABS 0 ! BRAKE MPH km/h 120 THEFT P R N D 2 1 L O/D OFF Check engine Your vehicle is equipped with a computer that monitors the engine's CHECK emission control system. This ENGINE system is commonly known as the On Board Diagnostics
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 7
    engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Fuel reset Illuminates when the ignition key is turned to the ON position and the fuel pump shut-off switch
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 8
    after releasing the parking brake indicates low brake fluid level. Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned on and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. ! BRAKE ABS 8
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 9
    -theft system (if equipped) Refer to Anti-theft system in the Controls and features chapter. THEFT Charging system Momentarily illuminates when the ignition is turned ON and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 10
    key is in the CHECK ON position and the engine coolant temperature is high, the engine oil GAGE pressure is low or the fuel level is near empty. Refer to Engine coolant temperature gauge, Engine oil pressure gauge or Fuel gauge in this chapter for more information. Four wheel drive low (if equipped
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 11
    the light flashes when you are driving, have your vehicle serviced. Speed control (if equipped) This light comes on when either the SET/ACCEL or RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 12
    Instrumentation GAUGES CHECK GAGE DOOR AJAR 4 H CHECK ENGINE 5 6 40 30 20 10 50 60 60 70 0 0 0 80 100 120 140 80 90 160 3 2 1 RPMx1000 C 40 000000 100 1 10 H L H SPEED CONT 4WD HIGH 4WD LOW 20 180 FUEL RESET F E ABS 0 ! BRAKE MPH km/h 120 THEFT P R N D 2 1 L O/D OFF
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 13
    area (the area between the ''H'' and ''C''). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the ignition and let the engine cool. Refer to Engine coolant in the Maintenance and care chapter. Never remove the coolant recovery cap while
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 14
    may damage the engine. 4 3 2 1 0 5 6 RPMx1000 Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle's electrical system checked as soon as possible
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 15
    to Checking and adding engine oil in the Maintenance and care chapter). If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician. Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 16
    features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings. FUEL ENGLISH METRIC RANGE STATUS ECON RESET SYSTEM CHECK OIL CHANGE RESET Selectable features English
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 17
    be in the Off position during fueling. The display FUEL LEVEL ERROR indicates a problem with the fuel indication system. See your dealer or qualified service technician for system maintenance. FUEL ENGLISH/ METRIC RANGE STATUS ECON RESET SYSTEM CHECK OIL CHANGE RESET Fuel status Press once to
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 18
    display to function properly. FUEL ENGLISH/ METRIC RANGE STATUS ECON RESET SYSTEM CHECK OIL CHANGE RESET Reset Press the reset control to reset the current feature being displayed. Warnings, distance driven, average fuel economy, fuel used and personalized oil reset percentage are the only
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 19
    indicates a problem with the system. Following this display, contact your dealer or qualified service technician for system maintenance. FUEL ENGLISH/ METRIC RANGE STATUS ECON RESET SYSTEM CHECK OIL CHANGE RESET Operating the message center during system check The message center controls can
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 20
    oil reset percentage has been established, it will be used beginning with the completion of your next OIL CHANGE RESET procedure. FUEL ENGLISH/ METRIC RANGE STATUS ECON RESET SYSTEM CHECK OIL CHANGE RESET FUEL ENGLISH/ METRIC RANGE STATUS ECON RESET SYSTEM CHECK OIL CHANGE RESET 20
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 21
    ) (if equipped) Turns the highbeam headlamps on with a reduced output. To activate: • the engine must be running • the headlamp control is in the OFF or Parking lamps position. The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your headlamps at dusk
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 22
    Controls and features High beams Push forward to activate. Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 23
    SYSTEM Manual heating and air conditioning system (if equipped) OFF A/C MAX A/C Fan speed control Controls the volume of air vehicle. OFF A/C MAX A/C The air conditioning compressor will operate in all modes except . However, the air conditioning will only function if the outside temperature is
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 24
    it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle's climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 25
    To prevent humidity buildup inside the vehicle, don't drive with the climate control system in the OFF position. • Don't put objects under the front seat that will interfere with the airflow to the back seats. • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 26
    . The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature. The system will automatically determine fan speed, airflow location and if fresh outside air or recirculated air is required. Fan speed 26
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 27
    thumbwheel is turned or the steering wheel fan speed control is pressed. When in AUTOMATIC and weather conditions require heat, air will be sent to the floor. However, if the engine is not warm enough to provide heat, the fan will be at a low speed and the air will be directed to the windshield. In
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 28
    one second) to switch between Fahrenheit and will also change the temperature display Fan speed ( ) When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel or steering wheel
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 29
    it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle's climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 30
    air conditioner will automatically dehumidify the air to prevent fogging. • OFF-Outside air is shut out and the fan will not operate. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle. Rear fan off Press REAR FAN OFF to turn off the rear console
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 31
    To prevent humidity buildup inside the vehicle, don't drive with the climate control system in the OFF position. • Don't put objects under the front seat that will interfere with the airflow to the back seats. • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 32
    (if equipped) Depending on the equipment package of your vehicle, the rear console may not be equipped with rear console audio/climate controls. Turn the air distribution control to the desired airflow position. - VOLUME + MODE SEEK MEMORY The instrument panel climate controls must be on
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 33
    Controls and features Select for air to flow through these vents: - VOLUME + BAND SEEK MEMORY for air to flow through Select these vents: - VOLUME + BAND SEEK MEMORY 33
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 34
    to the OFF position. To manually turn off the defroster before ten minutes have passed, push the control again. 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to Four-wheel drive (4WD) operation in the Driving chapter for more information. AUTO HIGH LOW AUDIO SYSTEM Refer to the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 35
    , locks the steering wheel, automatic transmission gearshift 1 lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 36
    N (Neutral) with the speed control on. To turn speed control off • Press OFF or • Turn off the vehicle ignition. ON OFF Once speed control is switched off, the previously programmed set speed will be erased. 36
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 37
    driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RES/RSM/RESUME will
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 38
    speed is reached or • Press and release SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 39
    and features • Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC/SET ACCEL. RSM SET ACC COAST To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 40
    km/h (30 mph). RSM SET ACC COAST Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position. SPEED CONT 40
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 41
    the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard lights control in the Roadside
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 42
    low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle's speed increases. Rear window wiper
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 43
    Controls and features Press the control for rear washer fluid operation. OFF R.WIPE HI PUSH STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Radio control features • Press MEM/NEXT to select a preset station
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 44
    control to open the storage compartment. The door will open slightly and can be moved to full open. LAM P DE MO N OPE Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the storage clip from
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 45
    point during one-touch opening, press the control a second time. • Press and hold (as desired) the front portion of the moon roof control to close. The moon roof has a sliding shade that can be manually opened or closed when the glass panel is shut. To close the shade, pull it toward the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 46
    falls below 3.3°C (38°F), the display will alternate from ''ICE'' to the outside temperature at a two second rate for one minute. The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 47
    in the display, then release. The display should show the current zone number. 3. Press the MODE control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated. LAMP MODE LAMP 9 VAR 47
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 48
    steel structures and high voltage lines: • Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release. • Drive the vehicle slowly (less is in the OFF position. Leaving the headlamp control on will override the autolamp. 2. Turn the ignition to the ON
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 49
    to the non-glare ''active'' state when bright lights (glare) reach the mirror. When the mirror detects bright light from front or behind, it will adjust automatically to minimize glare. The mirror will automatically return to the normal position whenever the vehicle is placed in R (Reverse) (when
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 50
    Controls and features POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO 50
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 51
    Controls and features One touch down • Press AUTO and release quickly. The window will open fully. Depress again to stop window operation. AUTO Window lock The window lock side of the control. Press the left side to restore the window controls. POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 52
    with the optional perimeter alarm system, this feature will work from all doors. CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 53
    glass if it is frozen in place. These actions could cause damage to the glass and mirrors. CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • utility compartment with cassette/compact disc storage • auxiliary power point • cupholders • tissue box holder
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 54
    the following features: • air vents • audio system controls • rear seat climate controls • cupholders Refer to the ''Audio Guide'' for more information on the rear console audio system controls. AUXILIARY POWER POINT The power point is an additional power source for electrical accessories. 54
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 55
    and features CENTER ARMREST/REAR CUPHOLDER Do not attempt to raise the console armrest when the rear cupholder is in use. If you find resistance when raising the armrest, make sure the cupholder is fully closed or else damage may occur to the armrest. POSITIVE RETENTION FLOOR MAT Position the floor
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 56
    locks, depress the key lock cylinder or press the door lock switch on the left side of the cargo area. The liftgate door and window should be closed before driving your vehicle. If not, possible damage may occur to the liftgate door lift cylinders and attaching hardware. Make sure that the liftgate
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 57
    in the case of a sudden stop or collision. Rewinding the shade With extended use, the cargo shade may lose its spring tension. If this occurs, the shade must be manually rewound. This is a two-person operation. 1. Remove the shade from the vehicle and extend it with the smooth grain facing you
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 58
    roller tube toward you 14 times. 5. Let go of the right end cap. The clutch will now engage and stop the shade from losing its spring tension. 6. Unfold the vinyl and place it into the end cap slots. 7. Insert the shade into the side mounting brackets and check to make sure that it operates properly
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 59
    five seconds to unlock all doors. Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash. If any of the doors are ajar, the horn
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 60
    alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions The remote entry system can also control the memory seat feature. 60
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 61
    transmitter programmed will not recall a memory position. Memory positions can be changed at any time. The memory feature can be deactivated or reactivated by performing the following: 1. Make sure the alarm system (if equipped) is not armed or triggered, the ignition is off and all doors and the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 62
    • weather conditions • nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 63
    position • you shift into or through R (Reverse) • the brake pedal is released The autolock feature repeats when: • any door is opened and then closed • the brake pedal is released Deactivating autolock Before following the activation or deactivation procedures, make sure that the anti-theft system
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 64
    key back to ON. The doors will lock and unlock. 6. Press the power door unlock switch. The horn will chirp once upon successful toggling of the Autolock feature. 7. Turn ignition to OFF. The horn will chirp to confirm procedure is complete. Keyless entry system (if equipped) With the keyless
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 65
    code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. If you wish to erase your personal code, use the following instructions
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 66
    same time within five seconds of step two. The system will now only respond to the factory-set code. 1 2 3 4 5 6 7 8 9 0 Unlocking the doors with the keyless entry system To unlock the driver's door, enter either the factory-set code or personal code (each digit pressed within 5 seconds of the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 67
    occurs, the system will flash the headlamps, parking lamps and the theft indicator lamp and will chirp the horn. The system is ready to arm whenever the ignition is turned OFF. Any of the following actions will prearm the alarm system: • Press the remote entry lock control • Open a door and press
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 68
    to lock the doors (doors opened or closed). 1 2 3 4 5 6 7 8 9 0 If a door is open, the system is prearmed and is waiting for the door to close. The theft indicator on the instrument cluster will be lit continuously when the system is prearmed. Once the doors are closed, the system will arm in
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 69
    front of the vehicle) to make sure the alarm disarms. • Unlock the doors by using your keyless entry keypad. 1 2 3 4 5 6 7 8 9 0 • Turn ignition to ACC or ON. • Press the panic control on the remote entry transmitter. This will disarm the system only if the alarm is sounding. SecuriLockி anti-theft
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 70
    . • When the ignition is turned to RUN or START, the theft indicator will light for 3 seconds and then go out. If the theft indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your dealership or a qualified technician. Programming spare SecuriLockி keys
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 71
    ignition switch and will start the vehicle's engine. The theft indicator (located on the instrument cluster) will light for three seconds and then go out. If the programming procedure was not successful, the new SecuriLock௢ key(s) will not operate the vehicle's engine. The theft indicator will flash
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 72
    cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 73
    . The memory seat control is located on the driver door. • To program position one, move 1 2 the driver seat to the desired position using the seat controls. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1. • To program
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 74
    Using the power lumbar support The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness. REAR SEATS Head restraints Push or pull the head rests to the desired position. 74
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 75
    built-in child seat is fully stowed. 1. Press the lower release control downward to unlatch the seatback. 2. Rotate the seatback downward into the load floor position. 3. Press down on the top outboard area of the seatback until a click is heard. The seat is now latched in the floor
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 76
    seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position. PUSH PUS H SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To prevent the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 77
    or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. Each seating position in your vehicle has a specific safety belt assembly which is made up of one
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 78
    front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts brakes suddenly or turns a corner sharply, or the vehicle receives an impact of 8 km/h (5 mph) or more, the combination safety belts will lock
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 79
    . • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 80
    is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt warning light and indicator chime The seat belt warning
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 81
    is illuminated and the warning chime is sounding...The safety belt warning light and The driver's safety belt is buckled before the ignition key indicator chime remain off. is turned to ON... Safety belt maintenance Check the safety belt systems periodically to make sure they work properly and are
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 82
    SYSTEM front passenger. • reduce certain upper body injuries. Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury. The right front passenger air bag is not designed to restrain occupants in the center front seating position
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 83
    on the steering wheel or in front seat areas that may come into contact with a deploying air bag. Failure to follow this instruction may increase the risk of personal injury in the event of a collision. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 84
    work? The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. The
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 85
    or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter. Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 86
    so it does not cross or rest in front of the child's face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. If the shoulder belt cannot be properly positioned: • move the child to one of the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 87
    motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child. A belt-positioning booster should be used if the shoulder belt rests in front
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 88
    be injured in a sudden stop or collision. Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. Air bag can kill or injure a child in a child seat. If you must use a forward-facing
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 89
    together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage. Make sure the tongue is latched
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 90
    5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 91
    ) is provided in the rear edge of the front passenger seat cushion frame. The anchorbracket must be installed using the instructions provided with the kit. Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 92
    to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle's interior during a sudden stop or crash. The second row seatback must be fully locked before operating the child restraint system. Check the position of the seatback release
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 93
    Seating and safety restraints 2. Pull both Velcro௡ straps to release the child seat cushion. 3. Lower the child seat cushion. 93
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 94
    4. Unfold the cushion protector flap onto adult seat cushion 5. If connected, disconnect the chest clip and buckles. 6. Place the child in the seat and position the left shoulder belt over the child's left shoulder first, then place the right shoulder belt over the child's right shoulder. 94
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 95
    Verify that the indicator window on each tongue is green to ensure proper safety belt connections. If both tongues do not latch in the buckle, do not use halves together and adjust the clip to comfortably hold the shoulder belts in place over the child's chest. The chest clip is designed to easily
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 96
    vehicle sensitive (emergency locking) mode, which allow some movement of the shoulder belts (like adult shoulder belts). In emergency locking mode, the shoulder belts of the child seat will lock in response to hard braking, hard cornering or if your vehicle is involved in a collision with an impact
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 97
    . 4. Fold the cushion protector flap onto the child seat cushion. Slide the belt tongues up and out of the way of the cushion, then return the child seat cushion to the stowed (upright) position. 5. Slide the Velcro௡ straps through the D-rings on the child seat cushion and attach. 6. Slide the head
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 98
    Seating and safety restraints 7. Press firmly on the top center of the built-in child safety seat head restraint to ensure it any collision. If the child seat was in use during a collision, Ford recommends replacing it. Built-in child restraints not in use during a collision should be inspected and
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 99
    drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine's idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Before
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 100
    Starting If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • If • • Make sure the gearshift is in P (Park). starting a vehicle with a manual transmission: Make sure the parking brake is set. Push the clutch pedal to the floor. 100
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 101
    CONT 4WD 20 180
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 102
    when the engine starts. 4. After idling for a few seconds, apply the brake and release the parking brake. Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 103
    could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service. • the sound of the exhaust system changes. • the vehicle has been damaged in a collision. Important ventilating information If the engine is idling while the vehicle is stopped in an
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 104
    conditions such as cold, heat, moisture, road dust, salt or mud. If a ''metal-to-metal'', ''continuous grinding'' or ''continuous squeal'' sound is present while braking, the brake linings may be worn-out and should be inspected by a qualified service technician. Anti-lock brake system (ABS
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 105
    Driving light will remain on and your vehicle should be serviced as soon as possible. Normal braking is still effective unless the BRAKE warning lamp is ! also illuminated. BRAKE Using ABS • In an emergency or when maximum efficiency from the ABS is required, apply continuous full force on the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 106
    to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. AIR SUSPENSION SYSTEM (IF EQUIPPED) The air suspension system is designed to improve ride, handling and general vehicle performance during: • certain road conditions • steering
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 107
    Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver. TRANSMISSION OPERATION Automatic transmission operation Brake Apply the brake pedal and chapter. Do not drive your vehicle until
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 108
    off the ignition whenever you leave your vehicle. Driving with a 4-speed automatic transmission (5.0L engines only) Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift. Hold the brake pedal down while you move the gearshift lever from
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 109
    the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position. The TCIL will illuminate on the instrument cluster. (Drive) provides Transmission operates in gears one through three. more engine braking than (Overdrive) and is
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 110
    Low) at higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed. Driving with a 5-speed automatic transmission (4.0L engines only) Understanding gearshift positions Hold the brake pedal down while you move the gearshift
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 111
    and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through five. (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 112
    the transmission control switch on the end of the gearshift lever with the gearshift in the position. The TCIL will illuminate on the instrument cluster. Transmission operates in gears one through four. (Drive) provides more engine braking than (Overdrive) and is useful whenever driving conditions
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 113
    that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission: 1. Hold down the brake pedal. 2. Put the gearshift lever in N (Neutral). 3. Depress the clutch pedal. 4. Crank the engine and let it idle for a few seconds. • Put
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 114
    Driving Recommended shift speeds Upshifts when accelerating (for best fuel economy) Transfer case position (if equipped) 71 km/h (41 mph) 27 km/h (17 mph) Upshifts when cruising (recommended for best fuel economy) Transfer case position (if equipped) Shift from: AUTO or HIGH LOW 1 -2 16 km/h (10 mph)
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 115
    move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse Ensure that the vehicle is at a complete stop before shifting into R (Reverse). Failure to do so may damage the transmission. Put the gearshift into N and wait at least several seconds before shifting
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 116
    a four-wheel drive mode best suited for your current driving conditions. Positions of the Control-Trac system The Control-Trac system functions in three modes: • The 4WD AUTO mode provides four-wheel drive with full power AUTO HIGH LOW delivered to the rear axle, and to the front axle as required
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 117
    four-wheel drive with full power to both axles and includes a lower gear ratio for low AWD, a spare tire of a different size than the road tires should never be used. Such a tire could result in damage to driveline components and make the vehicle difficult to control. Utility and four-wheel drive
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 118
    light will turn off. Either shift can be done at a stop or while driving at any speed. Shifting from 4WD AUTO or 4WD HIGH to 4WD LOW 1. Bring the vehicle to a stop. 2. Depress the brake. AUTO HIGH LOW 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 119
    4WD HIGH 1. Bring the vehicle to a stop. 2. Depress the brake. AUTO HIGH LOW 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 4WD AUTO or 4WD HIGH position. Driving off-road with 4WD Your vehicle is specially
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 120
    causes an imbalance that could damage drive components. If the transmission and transfer case are submerged in water, their fluids should be checked and changed, if necessary. Water intrusion into the transmission may damage the transmission. If the rear axle is submerged in water, the rear
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 121
    . In order to allow the anti-lock brake system (ABS) to operate properly, keep steady pressure on the brake pedal. Allow more stopping distance and drive slower than usual. Consider using one of the lower gears. ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) (5.0L ENGINES ONLY) Your vehicle is equipped
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 122
    , then press lightly on the accelerator. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine can overheat. Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander. Sand When driving over sand
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 123
    causes an imbalance that could damage drive components. If the transmission and transfer case are submerged in water, their fluids should be checked and changed, if necessary. Water intrusion into the transmission may damage the transmission. If the rear axle is submerged in water, the rear
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 124
    . In order to allow the anti-lock brake system (ABS) to operate properly, keep steady pressure on the brake pedal. Allow more stopping distance and drive slower than usual. Consider using one of the lower gears. TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 125
    Driving the driver's door pillar. • GAWR (Gross Axle Weight Rating) : Carrying capacity for each axle system. The GAWR equals the vehicle curb weight for each engine/transmission combination, any required option weight for trailer Do not use replacement tires with lower weight capacities than the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 126
    vehicle slowly while applying light pressure on the brake pedal. TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package. Trailer towing puts additional loads on your vehicle's engine, transmission, axle, brakes, tires, and suspension. For your safety and
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 127
    the total weight. Trailer towing table (4x2 manual transmission) GCWR (Gross Combined Weight Rating)/Trailer weights Rear Maximum Trailer weight Maximum Engine axle GCWR-kg range-kg (lbs.) frontal area of ratio (lbs.) (0-Maximum) trailer-m2 (ft2) 2-door 4.0L EFI 3.27 2 721 (6 000) 0-907 (0-2 000
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 128
    Driving Trailer towing table (4x4 manual transmission) GCWR (Gross Combined Weight Rating)/Trailer weights Rear Maximum Trailer weight Maximum Engine axle GCWR-kg range-kg (lbs.) frontal area of ratio (lbs.) (0-Maximum) trailer-m2 (ft2) 2-door 4.0L EFI 3.27 2 721 (6 000) 0-871 (0-1 920) 4.64 (50) 4.
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 129
    Driving Trailer towing table (4x2 automatic transmission) GCWR (Gross Combined Weight Rating)/Trailer weights Rear Maximum Trailer Weight Maximum Engine axle GCWR-kg Range-kg (lbs.) frontal area of ratio (lbs.) 0-Maximum trailer-m2 (ft2) 2-door 4.0L 3.27 3 402 (7 500) 0-1 361 (0-3 000) 4.64 (50)
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 130
    Driving Trailer towing table (4x4 and AWD with automatic transmission) GCWR (Gross Combined Weight Rating)/Trailer Weights Rear Maximum Trailer Weight Maximum Engine axle GCWR-kg Range-kg (lbs.) frontal area of ratio (lbs.) 0-Maximum trailer-m2 (ft2) 2-door 4.0L 3.27 3 402 (7 500) 0-1 524 (0-3 360)
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 131
    and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you. Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer's specifications. The trailer
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 132
    and upshifting for optimum fuel economy and transmission cooling. • Anticipate stops and brake gradually. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the Severe Duty Schedule in your ''Service Guide'' for more
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 133
    check your hitch, electrical connections and trailer wheel lug nuts. • When stopped in traffic for long periods of time in hot weather, place the gearshift in P (Park) (automatic transmissions) or 1 (First) (manual transmissions) and increase idle speed. This aids engine cooling and air conditioner
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 134
    Driving To adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide cross-bar to the desired location. 3. Tighten thumbwheel at both ends of the cross-bar. FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 135
    . The ''Fuel Reset'' indicator light will illuminate in the instrument cluster. The shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. 1. Turn the ignition switch to the OFF position. 2. Check the fuel system for leaks
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 136
    fuel pump shut-off switch is located in the passenger's foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 137
    amp 30 amp fuse link 40 amp fuse link 50 amp fuse link 60 amp fuse link 80 amp fuse link 100 amp fuse link Color Tan Brown Red Light blue Yellow Light blue Natural Light green Pink Green Red Yellow Black Dark blue 137
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 138
    Roadside emergencies Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver's side door. Pull the panel cover outward to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover. 12 16
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 139
    Assembly, Brake Pressure Switch, Generic electronic Module (GEM), Shift Lock Actuator, Blend Door Actuator, A/C - Heater Assembly, Flasher Instrument Cluster Power Window Relay, Washer Pump Relay Brake Pedal Position Switch, Brake Pressure Switch 4 Wheel Anti-Lock Brake System (4WABS) Module, 4WABS
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 140
    NOT USED Clutch Pedal Position (CPP) Switch, Starter Interrupt Relay, Anti-Theft Generic Electronic Module (GEM), Instrument Cluster, Securi-Lock Battery Saver Relay, Electronic Shift Relay, Interior Lamp Relay, Power Window Relay, Electronic Shift Control Module DRL, Backup Lamps Switch, DTR Sensor
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 141
    power distribution box is located in the engine compartment near the battery. The power distribution box contains high-current fuses that protect your vehicle's main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 142
    2 40A** Blower Motor Relay 3 50A** 4 Wheel Anti-Lock Brake System (4WABS) Module 4 30A** Power Windows, Power Moon Roof, Power Seat 5 50A** Ignition Switch, Starter Relay 6 20A** Transfer Case Relay 7 - NOT USED 8 20A** Automatic Ride Control ARC Switch Off/On Switch 9 40A** Automatic Ride Control
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 143
    4 Wheel Anti-Lock System (4WABS) Module 8 15A* Rear Wiper Motor 9 20A* Fuel Pump Relay and RAP Module 10 15A* Horn Relay 11 15A* Parklamps Relay and Mainlight Switch 12 30A* Mainlight Switch and Multifunction Switch 13 15A* Heated Oxygen Sensor, EGR Vacuum Regulator, EVR Solenoid, Camshaft Position
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 144
    , lug nut wrench Jack handle Location Under the vehicle, just in front of the rear bumper Left rear quarter panel behind interior trim Behind rear seats, under carpet Removing the spare tire 1. Insert the jack handle into the rear bumper opening. The handle will stop moving and forward resistance
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 145
    when the tire is raised to the stowed position. It will not allow you to overtighten. Tire change procedure On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to the instruction sheet for detailed tire change
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 146
    lug nut, but do not remove them until the wheel is raised off the ground. 6. Turn OFF the air suspension switch (if equipped). Refer to Air suspension system in the Driving chapter. 7. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 147
    Roadside emergencies • Front • Rear 147
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 148
    the wheel by turning the jack handle counterclockwise. 11. Remove the jack and fully tighten the lug nuts in the order shown. 1 3 4 5 2 12. Stow the flat tire, jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 13. Turn ON the air suspension switch (if
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 149
    the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables 1. Position
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 150
    Roadside emergencies • 4.0L SOHC 4 1 + - - + 3 2 150
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 151
    the jump leads are clear of moving parts of the engine. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may booster battery terminal (2). 2. Remove the cable from the positive (+) terminal of the booster battery (3) and then the
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 152
    Roadside emergencies • 4.0L SOHC 1 4 + - - + 2 3 152
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 153
    Roadside emergencies • except 4.0L SOHC 4 1 + - - + 2 3 3. After the disabled vehicle has been started, allow it to idle for a while so the engine can ''relearn'' its idle conditions. 153
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 154
    vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. If equipped with air suspension, the air suspension control must be turned to the OFF position. The Ford approved towing procedure is flatbed or wheel lift with dollies. On 4x2 vehicles, it
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 155
    emergencies When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for proper hook-up and towing procedures for your vehicle. 155
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 156
    away from the battery and all fuel related parts. If you disconnect the battery, the engine must ''relearn'' its idle conditions before your vehicle will drive properly, as explained in Battery in this chapter. Working with the engine off • Automatic transmission: 1. Set the parking brake and ensure
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 157
    moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels to prevent the vehicle from moving unexpectedly
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 158
    fluid reservoir 2. Engine oil fill cap 3. Transmission fluid dipstick (automatic transmission only) 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Clutch fluid reservoir (manual transmission only) 8. Battery 9. Air filter assembly 10. Engine coolant reservoir
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 159
    and care 4.0L SOHC engine 1 2 3 4 5 9 8 7 6 1. 2. 3. 4. 5. 6. 7. 8. 9. Windshield washer fluid reservoir Transmission fluid dipstick Engine oil fill cap Engine oil dipstick Brake fluid reservoir Battery Power steering fluid reservoir Air filter assembly Engine coolant reservoir 159
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 160
    Windshield washer fluid reservoir Engine oil fill cap Automatic transmission fluid dipstick Brake fluid reservoir Battery Power steering fluid reservoir Engine oil dipstick Air filter assembly ENGINE OIL Checking the engine oil Check the engine oil each time you fuel your vehicle. 1. Make sure
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 161
    Maintenance and care 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 4.0L
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 162
    ) or the MAX mark (5.0L engines) may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 163
    . Severe duty operation would include extensive idling, trailer towing, driving in severe dust and police, taxi or delivery service. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 164
    should be checked and refilled as needed at least once each year: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 165
    and care Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. CLUTCH FLUID (IF EQUIPPED) During normal operation, the fluid level in the clutch reservoir will slowly rise. If the fluid level drops, maintain the fluid level at the step in the reservoir
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 166
    fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. SHER FL WA ONLY UID RADIATOR COOLANT ONLY Do not put engine coolant
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 167
    should replace it with a 50/50 mixture of coolant and distilled water as soon as possible. Check the coolant level in the coolant recovery reservoir the next few times you drive the vehicle. If necessary, add enough of a 50/50 mixture of coolant and water to bring the liquid level to the fill line
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 168
    capacities in the Capacities and specifications chapter. Have your dealer check the engine cooling system for leaks if you have to add more than a liter (quart) of engine coolant per month. Severe winter climate If you drive in extremely cold climates (less than -36°C [-34°F]), it may be necessary
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 169
    Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year. If adding fluid is necessary, use only MERCON௡ ATF power steering fluid. • 4.0L EFI engine • 4.0L SOHC engine T OVER FILO L DO N EE R OW FLUID ER ST ING P 169
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 170
    let it run until it reaches normal operating temperature (the engine coolant temperature gauge will be near the center of the NORMAL band). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. 5. If your
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 171
    you notice some sign of fluid leakage. Transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 32 km (20 miles) of driving. The transmission fluid should be in this range if
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 172
    and/or possible damage. If the fluid level is above the crosshatch (hot operating range) area after driving the vehicle for approximately 30 km (20 miles), excess transmission fluid should be removed by a qualified technician. DON'T ADD IF IN CROSSHATCHED AREA • CHECK WHEN HOT IDLING IN PARK 172
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 173
    Maintenance and care Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 174
    Maintenance and care Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 175
    help prevent corrosion. If your battery has a cover/shield, make sure it is reinstalled after the battery is replaced. Because your vehicle's engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 176
    and care relearn its idle conditions before your vehicle will drive properly. To begin this process: 1. Put the gearshift in P (Park) (automatic transmissions) or the neutral position (manual transmissions), turn off all accessories and start the vehicle. 2. Let the engine idle for at least one
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 177
    replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department rate of the tire when tested under controlled conditions on a specified government test course. For example
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 178
    grade assigned to this tire is based on braking (straight ahead) traction tests and does not controlled conditions on a specified indoor laboratory test wheel. Sustained SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 179
    vehicle's tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the ''Service Guide''. If you notice that the tires wear unevenly, have them checked. • Four tire rotation 179
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 180
    tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias-belted, or bias-type tires. Use only the tire sizes that are listed on the on the decal. If you do not follow these precautions, your vehicle may not drive properly and safely. 180
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 181
    replacement accessory and recommends use of these or their equivalents. See your dealer or qualified service wheels. Chains may chip the wheels. • Install cables securely, verifying that the cables do not touch any wiring, brake lines or fuel lines. • Drive suspension insulation and bumpers will help
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 182
    overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system may be under pressure. If the fuel cap is venting vapor or if you hear
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 183
    fuels. However, even though your engine will perform adequately on other gasolines, the performance of the emission control devices and systems may be adversely affected. Repair of damage caused by using a fuel lightly. However, if it knocks heavily under most driving conditions on fuel with the 183
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 184
    and care recommended octane, see your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of ''Regular'' gasoline. ''Premium'' gasoline
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 185
    replacements or for service of components affecting emission control such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 186
    with the ''check engine/service engine soon'' light on. If the vehicle's powertrain system or its battery has just been serviced, the OBD-II system is reset to a ''not ready for I/M test'' condition. To ready the OBD-II system for I/M testing, a minimum of 30 minutes of city and highway driving is
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 187
    sure headlamp switch is in OFF position, then open the hood. If you are replacing the driver side headlamp, unclip the electronic module on the right side of the battery and move it out of the way. 2. Locate the headlamp bulb through the hole in the upper radiator support assembly. 3. Disconnect
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 188
    to turn the bulb left or right to line up the grooves in the plastic base with the plastic base until it snaps, locking it into position. 4. Turn the headlamps on and make sure 906) Front door courtesy lamp 1 168 Map lamps 2 168 (T10) Ashtray lamp 1 161 To replace all instrument panel lights - see
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 189
    's front structure is in its factory alignment condition. If the vehicle has been in an accident requiring the front end of the vehicle to be repaired, the horizontal indicator should be recalibrated by the servicing facility according to instructions in the vehicle's Workshop Manual. D U 189
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 190
    the horizontal indicator and adjusting screw. They are located below the viewing hole at the rear of the headlamp assembly. 2. Use a 4mm wrench or socket to turn the horizontal adjusting screw until the ''0'' mark on the yellow dial lines up with the reference mark on the marker (as shown) when
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 191
    counterclockwise until the bubble is centered over the ''0'' mark. Guide'' for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold accessories, such as antennas, before entering a car wash. After washing, apply the brakes several times to dry
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 192
    months, depending on operating conditions. Use only carnauba or the Ford accessory line. Observe the application instructions on the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water to avoid cracking the engine block or other engine
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 193
    Maintenance and care • 5.0L • 4.0L SOHC • 4.0L EFI • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. 193
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 194
    the same detergent as the body of your vehicle. Do not use acid-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar remover to remove grease and tar. Cleaning plastic exterior parts Use vinyl cleaner for
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 195
    cleaning products because they may weaken the safety belt webbing or damage the vinyl parts of the seat. The child seat liner is removable and may be machine-washed and air dried. Underbody Flush the complete underside of vehicle frequently. Keep body drain holes unplugged. Inspect for road damage
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 196
    -01276) are available through your local 3M distributor. Call 1-800-742-9649 for the nearest distributor in your area. PART NUMBER (Obtain Locally) (Obtain Locally) PART NAME Tanners Preserve Leather Cleaner 3M ЉType TЉ Clean and Finish Scrubbing Pads Woodtone trim Wipe stains with a soft cloth
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 197
    Capacities and specifications MOTORCRAFT PART NUMBERS 4.0L EFI 4.0L SOHC 5.0L engine engine engine Air filter FA-1616 FA-1658 FA-1658 Fuel filter FG-872 FG-872 FG-872 Battery BXT-65-650 BXT-65-650 BXT-65-650 Oil filter FL-1A FL-1A FL-820S PCV valve EV-225 EV-225 EV-152 Spark plugs* AGRF-22P AGRF
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 198
    CAPACITIES Fluid Engine oil (including filter change) Brake fluid Ford Part Name Motorcraft 5W30 Super Premium Motor Oil Ford High Performance DOT 3 Brake Fluid Motorcraft MERCON௡ ATF Application All engines Capacity 4.7L (5.0 quarts) All All 5-speed manual 4R70W Automatic (5.0L engines only) 5R55E
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 199
    or 4.0L EFI engines and 3.73 or 4.10 rear axle ratios or 5.0L engines require synthetic rear axle lubricant. Rear axles containing synthetic lubricant are lubricated for life. These lubricants are not to be checked or changed unless a leak is suspected, service required or the axle assembly has been
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 200
    Ford Part Number C9AZ-19550-AA OR -BA Ford Specification ESR-M17P5-A Body hinges, latches, door stricker plates and rotors, seat tracks, fuel filler Multi-Purpose Grease door hinge and spring, hood latch, auxiliary latch High Hydraulic clutch master cylinder Perfromance DOT 3 Motor and brake master
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 201
    reservoir Ford conventional and traction lok rear axles Front axle Transfer case Four wheel drive 5-speed manual transmission Transfer case Front Output Slip Shaft 1 Ford Part Name or equivalent Motorcraft MERCON ௡ATF Refer to footnotes 1, 2 and 3 4x4 Gear Oil Motorcraft MERCON௡ ATF Motorcraft
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 202
    and specifications ENGINE DATA Engine Cubic inches Horsepower Torque Required fuel grade Firing order Spark plug gap Ignition system Compression ratio 4.0L EFI engine 245 160 @ 4200 rpm 225 lb. ft. @ 2750 rpm 87 octane 1-4-2-5-3-6 1.3 mm-1.4 mm (0.052-.056 inch) EDIS 9.0:1 4.0L SOHC engine 245 205
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 203
    Capacities and specifications 4 1 3 5 2 203
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 204
    be located. The Safety Compliance Certification Label is located on the front door latch pillar on the driver's side. MFD. BY FORD MOTOR CO. /33 PSI COLD PRESSURE (RR) XXX kPa/33 PSI COLD TRAILER TOWING - SEE OWNER GUIDE EXT PNT: XXXXXX XXXXXX RC: XX DSO: XXXX F0000 BAR INT TR TP/PS R AXLE TR SPR
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 205
    safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (202-366-0123
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 206
    ...86 indicator light ...85 passenger air bag ...84 Air conditioning manual heating and air conditioning system ...23,25 Air suspension description ...106 All wheel drive (AWD) ...121 Ambulance packages ...3 Anti-lock brake system (ABS) description ...104 Anti-theft system ...67 Autolamp system (see
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 207
    anti-theft ...9 brake ...8 charging system ...9 check engine ...6,7 cruise indicator ...11 door ajar ...10 fuel reset ...7 overdrive off ...11 safety belt ...8 turn signal indicator ...9 Load limits trailer towing ...126 Lubricant specifications ...200 Luggage rack ...133 Manual transmission driving
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 208
    display ..44 storage compartment ...44 Panic alarm feature, remote entry system ...60 Parking brake ...105 Power door locks ...51 Power steering fluid, checking and adding ...169 Rear window washer ...42 Recreational towing, all wheels on the ground ...133 Refill capacities for fluids ...198 Relays
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 209
    Number (VIN) ...204 Vehicle loading ...124 Ventilating your vehicle ...103 Warning chimes ...6 Windows power windows, operating ...50 Windshield washer fluid and wipers checking and adding fluid ...166 checking and replacing wiper blades ...176 operation ...42 Wrecker towing ...154 209
  • 1998 Ford Explorer | Owner Guide 1st Printing - Page 210
    Filling station information Recommended fuel Fuel tank capacity (2 door) Fuel tank capacity (4 door) Engine oil capacity (with filter change) Unleaded fuel only - 87 octane 66.2L (17.3 gallons) 79.5L (20.8 gallons) 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford Specification
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
Before driving
Introduction
2
Instrumentation
4
Controls and features
21
Seating and safety restraints
72
Starting and driving
Starting
99
Driving
104
Roadside emergencies
135
Servicing
Maintenance and care
156
Capacities and specifications
197
Reporting safety defects
205
Index
206
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company.
Copyright
°
1997 Ford Motor Company
Elemental Chlorine Free
Contents
1