2010 Toyota Corolla Navigation Manual
2010 Toyota Corolla Manual
2010 Toyota Corolla manual content summary:
- 2010 Toyota Corolla | Navigation Manual - Page 1
COROLLA CUSTOMER EXPERIENCE CENTER 1-800-331-4331 2 0 1 0 NAVIGATION SYSTEM QUICK REFERENCE GUIDE Printed in U.S.A. 1/09 08-TCS-02928 00505-NAV10-COR - 2010 Toyota Corolla | Navigation Manual - Page 2
TABLE OF CONTENTS LIMITATIONS OF THIS QUICK REFERENCE GUIDE BASIC OPERATION DESTINATION INPUT By Address DESTINATION INPUT - POINTS OF INTEREST (POI) Points of Interest by Name Points of Interest by Category DESTINATION INPUT - TELEPHONE NUMBER Business or Registered Addresses SET HOME ADDITIONAL - 2010 Toyota Corolla | Navigation Manual - Page 3
or turn off the screen. Change the angle of the screen for best viewing. AUDIO Button Set the radio station presets, adjust the balance and tone controls. È MENU Button Access Voice Guidance Volume, Select User, My Places, Setup and Suspend Guidance. DESTINATION Button Input the destination by one - 2010 Toyota Corolla | Navigation Manual - Page 4
step 1 Press the DEST panel button followed by and move to step 3. To change Region, touch and move to step 2. step 2 Select the desired Region and . touch step 3 Input the house number and touch . step 4 and input the Touch to see street name. Touch all of the available options. Quick - 2010 Toyota Corolla | Navigation Manual - Page 5
DESTINATION INPUT BY ADDRESS step 7 Use or to scroll up or down. Touch the desired city. Select the desired street. step 8 Select the desired Route Preference by - 2010 Toyota Corolla | Navigation Manual - Page 6
- POINTS OF INTEREST (POI) POINTS OF INTEREST BY NAME step 1 Press the DEST panel button followed by . step 2 Touch . step 3 Input the POI name and touch . step 4 or to scroll up Use or down. Touch the desired destination Quick Tip - If the POI isn't listed in - 2010 Toyota Corolla | Navigation Manual - Page 7
DESTINATION INPUT - POINTS OF INTEREST (POI) POINTS OF INTEREST BY CATEGORY step 1 Press the DEST panel button followed by . step 2 Touch . step 3 Touch . step 4 Touch the desired - 2010 Toyota Corolla | Navigation Manual - Page 8
. It is number followed by not necessary to dial "1." Quick Tip - Personal telephone numbers cannot be used for Destination input unless previously added in the Address Book. step 3 Select the business or registered address from the screen. step 4 See page 10 to select the desired Route - 2010 Toyota Corolla | Navigation Manual - Page 9
house number and . touch Tip - For security reasons, use a point close to your home instead of your actual home address. step 5 and input the Touch street name. Touch to see all of the available options. step 6 Use or to scroll up or down. Touch the desired street and - 2010 Toyota Corolla | Navigation Manual - Page 10
keys to adjust the position on the map. Touch to confirm the position. step 10 Touch at the top left of the screen to change the home icon. step 11 Touch the desired icon for your home. step 12 Touch the screen. at the bottom of 9 - 2010 Toyota Corolla | Navigation Manual - Page 11
area or will indicate that the address cannot be found. Select the desired Region and touch . ROUTE PREFERENCES 3 ROUTES Once the address has been inputted, select the desired route preference(s) for the trip. For example, if Toll Road is not selected, the system will route over non-toll roads - 2010 Toyota Corolla | Navigation Manual - Page 12
confirm your selection. KEYBOARD SETTING SCREEN TRANSITION PRESS MENU > SETUP Set the layout of the keyboard as alphabetical to or standard QWERTY . Once the screen transition is switched off, the audio or climate control screen (if equipped) will remain without reverting to the map display. - 2010 Toyota Corolla | Navigation Manual - Page 13
ADDITIONAL NAVIGATION FEATURES ESTIMATED DISTANCE AND TIME - 2010 Toyota Corolla | Navigation Manual - Page 14
and flow data are updated 12 times each hour from a variety of sources. XM NavTraffic® service is available in 80 major metropolitan areas across the continental US with more to come. New Corolla owners with factory-installed navigation receive a 90-day complimentary trial subscription from XM.* Traf - 2010 Toyota Corolla | Navigation Manual - Page 15
Touch to overlay traffic event and flow indicators on the map. Traffic flow is displayed by color lines right along the side of the freeways: Free flow traffic Moderate traffic Heavy congestion 2 Auto Avoid Traffic: Touch to have the system automatically select another route when moderate or heavy traf - 2010 Toyota Corolla | Navigation Manual - Page 16
BASIC FUNCTIONS SECTION BASIC FUNCTIONS Basic information before operation D Display operation D Initial screen D Touch screen operation D Inputting letters and numbers/List screen operation D Function help D Map screen operation Current position display ...Screen scroll operation ...Switching the - 2010 Toyota Corolla | Navigation Manual - Page 17
switch is set at OFF, the display will automatically move back to position 0 . The display will automatically resume the previous position when the engine switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system- If the engine switch is set at OFF, the display will automatically - 2010 Toyota Corolla | Navigation Manual - Page 18
with smart key system - When the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode, the initial screen will cold conditions, the display may react slowly or operation sound may become louder. CAUTION When the vehicle is stopped with the engine running, always apply the parking brake - 2010 Toyota Corolla | Navigation Manual - Page 19
replace certain parts or components and shows dealer information (if registered) on the screen. When the vehicle reaches a previously set driving distance or date specified for a scheduled maintenance check touched, the screen will change back to "CAUTION" screen and then change to the map screen in - 2010 Toyota Corolla | Navigation Manual - Page 20
the touch screen buttons on the screen. To prevent damage to the screen, lightly touch buttons on the screen with the finger. When a button on the slightly distorted when the display is cold. D Under extremely cold conditions, the map may not be displayed and the data input by a user may be deleted. - 2010 Toyota Corolla | Navigation Manual - Page 21
an address or a name, or entering a memo, letters and numbers can be input via the touch screen. D To input letters To display the alphabet keys, touch "A−Z" or " ". INFORMATION Keyboard layout can be changed. (See page 112.) Enter letters by touching the alphabet keys directly. Touching this - 2010 Toyota Corolla | Navigation Manual - Page 22
BASIC FUNCTIONS D To input numbers and symbols To display the number keys and symbol keys, touch "0−9". D To display the list Enter numbers and symbols by touching the number keys - 2010 Toyota Corolla | Navigation Manual - Page 23
beginning of the name. 2. Select the desired sorting criteria. Sorting criteria are as follows: "Distance": To sort in the order of distance from your current location. "Date": To sort in the order of the date. "Category": To sort in the order of the category. "Icon": To sort in the order of - 2010 Toyota Corolla | Navigation Manual - Page 24
BASIC FUNCTIONS Function help TYPE B Explanations for the functions of the "Destination", "Setup", "Menu" and "XM NavTraffic" screens can be viewed. "Dist. Sort": To sort in the order of distance from the current vehicle location. The distance from current vehicle position up to the destination is - 2010 Toyota Corolla | Navigation Manual - Page 25
scrolled, the map remains centered at the selected location until another function is activated. The current vehicle along the designated route. INFORMATION D After battery disconnection, or on a new vehicle, displayed. D To correct the current position manually, see page 118. INFORMATION When the - 2010 Toyota Corolla | Navigation Manual - Page 26
to a specific point. Touch "Enter ". The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 65.) If there is already a set destination, "Add to " and "Replace " are displayed. "Add to ": To add a destination - 2010 Toyota Corolla | Navigation Manual - Page 27
BASIC FUNCTIONS To change the icon or name, etc., see " - Editing memory points" on page 98. Up to 106 memory points can be registered. If there is an attempt - 2010 Toyota Corolla | Navigation Manual - Page 28
touched, the position of the cursor is set as a destination. If there is already a set destination, "Add to " and "Replace " are displayed. "Add to ": To add a destination. "Replace ": To delete the existing destinations and set a new one. To register this POI as a memory point, touch "Mark". (See - 2010 Toyota Corolla | Navigation Manual - Page 29
BASIC FUNCTIONS - Switching the screens DESTINATION INFORMATION When the cursor is set on a destination icon, the name and "Info." are displayed on the top of the screen. Any one of the screen configurations can be selected . 1. Touch this button to display the following screen. Touch "Info.". - 2010 Toyota Corolla | Navigation Manual - Page 30
BASIC FUNCTIONS Depending on the conditions, certain screen configuration buttons cannot be selected. : To display the single map screen. (See page 35.) : To display the dual map screen. (See page 36.) : To display the compass mode screen. (See page 36.) : To display the turn list screen. (See page - 2010 Toyota Corolla | Navigation Manual - Page 31
in the direction of the destination. INFORMATION This screen can perform the following procedures: 1. Changing the map scale 2. Displaying the POI icon 3. Show XMr NavTraffic Info. (See page 120.) 4. Changing the orientation of the map Touch "OK" when you complete editing. The screen returns to - 2010 Toyota Corolla | Navigation Manual - Page 32
D If the map or the current position is moved to the area which is not covered by the foot print map, the screen scale automatically changes to 150 feet (50 m). D On the foot print map, a one way street is displayed by . D It is not possible to perform scrolling on the foot - 2010 Toyota Corolla | Navigation Manual - Page 33
recorded on the map disc. 1. Touch "Info." while the foot print map is displayed. If the map is displayed by a split screen, the map will change into a single map display. Details of POIs in some buildings may be displayed. For detailed POI information, touch the building name. You can see details - 2010 Toyota Corolla | Navigation Manual - Page 34
BASIC FUNCTIONS - Orientation of the map The orientation of the map can be changed from North−up to Heading−up by touching the orientation symbol at the top left of the screen. Touch or . " North−up screen " Heading−up - 2010 Toyota Corolla | Navigation Manual - Page 35
BASIC FUNCTIONS 40 - 2010 Toyota Corolla | Navigation Manual - Page 36
DESTINATION SEARCH SECTION DESTINATION SEARCH Destination search D Quick reference ("Destination" screen) D Destination search Selecting the region to search ...Destination search by Home ...Destination search by Quick access ...Destination search by "Address" ...Destination search by "POI" ... - 2010 Toyota Corolla | Navigation Manual - Page 37
house number and the street address can be input by using the input keys...47 2 "POI" Select one of the starting point...60 5 "Memory" The location can be selected from the registered "Memory Emergency" One of the four categories of emergency service points that are already stored in the system's - 2010 Toyota Corolla | Navigation Manual - Page 38
10 "?" Function help for the "Destination" screen can be viewed on this screen...29 11 "Del. Dest." Set destinations can be deleted...64 12 "Change" To change the selected region to search, touch this button...44 13 Quick access touch screen buttons One of 5 preset memory points can be selected by - 2010 Toyota Corolla | Navigation Manual - Page 39
search SELECTING THE REGION TO SEARCH ON THE DESTINATION SCREEN 1. Push the "DEST" button. SELECTING THE REGION TO SEARCH ON THE INPUT SCREEN Change the selected region in order to set a destination from a different region by using "Address", "POI", "Freeway Ent./Exit" or "Intersection". 2. Touch - 2010 Toyota Corolla | Navigation Manual - Page 40
DESTINATION SEARCH U.S.A. Button "US1" "US2" States included in the search region Idaho Oregon Washington California Nevada Arizona Colorado Montana New Mexico Utah Wyoming Iowa Kansas Minnesota Missouri North Dakota Nebraska South Dakota Oklahoma Texas Illinois Indiana Kentucky Michigan Ohio - 2010 Toyota Corolla | Navigation Manual - Page 41
"Enter" is touched even while driving. 2. Touch any of the quick access touch screen buttons on the "Destination" screen. The screen changes and displays the map location of the quick access point and the route preference. (See "Starting route guidance" on page 65.) If a quick access point has not - 2010 Toyota Corolla | Navigation Manual - Page 42
numbers directly on the screen to input a house number. After inputting a house number, touch "OK" to display the screen for inputting a street name. It is possible to input a street name first. Touch "Street" to display the screen for inputting a street name. 2. Input the street name and touch - 2010 Toyota Corolla | Navigation Manual - Page 43
displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 65.) If the same address exists in more than one city, the current screen changes to the city list screen. If inputting a street name first, the screen changes. The house number - 2010 Toyota Corolla | Navigation Manual - Page 44
a city name. To search by city, the following three methods are possible. 1. Input the city name 2. Select from the nearest 5 cities 3. Select from the last 5 cities INFORMATION D To change the selected region, touch "Select Region". D To cancel the city setting, touch "Any City". 3. Touch the - 2010 Toyota Corolla | Navigation Manual - Page 45
FROM THE LAST 5 CITIES 2. Touch the button of the desired city name from the displayed list. The current screen changes to the screen for inputting a house number or a street name. (See "(a) Inputting a house number and a street name" on page 47.) Touch the button of the desired city name. If the - 2010 Toyota Corolla | Navigation Manual - Page 46
the desired method. 2. Touch the button of the desired destination. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 65.) When inputting the name of a specific Point of Interest, and there are two or more - 2010 Toyota Corolla | Navigation Manual - Page 47
POI icons" on page 82.) To search by city, the following three methods are possible. 1. Input the city name 2. Select from the nearest 5 cities 3. Select from the last 5 cities INFORMATION D To change the selected region, touch "Select Region". D To cancel the city setting, touch "Any City". 52 - 2010 Toyota Corolla | Navigation Manual - Page 48
DESTINATION SEARCH INPUTTING THE CITY NAME 1. Touch "Input City Name". SELECTING FROM THE NEAREST 5 CITIES 1. Touch "Nearest 5 Cities". 2. Input the city name. 2. Touch the button of the desired city name. 3. Touch the button of the desired city name from the displayed list. 53 - 2010 Toyota Corolla | Navigation Manual - Page 49
DESTINATION SEARCH SELECTING FROM THE LAST 5 CITIES D Selecting from the categories Touch the button of the desired city name. If the navigation has never been used, no cities will be displayed on the screen. Touch "Category". If the desired POI category is on the screen, touch the name to - 2010 Toyota Corolla | Navigation Manual - Page 50
the search point by the following method: 1. Input the city center 2. Set the current position as the search point 3. Set the search point via the map screen 4. Set the search point from any destination It is possible to display the names of POIs located within approximately 20 miles (32 km) from - 2010 Toyota Corolla | Navigation Manual - Page 51
DESTINATION SEARCH SETTING THE CURRENT POSITION AS THE SEARCH POINT Touch "Current Position". The search point is set at the current position, and the "POI Category" screen will be displayed. SETTING THE SEARCH POINT VIA THE MAP SCREEN 1. Touch "Map". When an arrow facing the desired point is - 2010 Toyota Corolla | Navigation Manual - Page 52
DESTINATION SEARCH SETTING THE SEARCH POINT FROM DESTINATIONS 1. Touch the destination buttons at the bottom of the screen. D To search POIs near the search point When the search point is set, the "POI Category" screen will be displayed. When an arrow facing the desired point is touched, the map - 2010 Toyota Corolla | Navigation Manual - Page 53
screen. "Show List": To display the list of POIs in the selected categories. 3. Input a telephone number. 4. After inputting a telephone number, touch "OK". The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page - 2010 Toyota Corolla | Navigation Manual - Page 54
on the "Destination" screen. The display changes to a screen to select police stations, dealers memory point. The screen changes and displays the map location of the selected destination and the desired destination. The screen changes and displays the map location of the selected destination and - 2010 Toyota Corolla | Navigation Manual - Page 55
and up to 100 previously set destinations are displayed on the screen. 3. Touch the button of the desired destination. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 65.) 2. To delete the point, touch - 2010 Toyota Corolla | Navigation Manual - Page 56
even while driving. However, the cursor cannot be moved. 4. Touch the button of the desired item. After inputting the two intersecting streets, the screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 65.) 61 - 2010 Toyota Corolla | Navigation Manual - Page 57
by "Freeway Ent./Exit" 1. Push the "DEST" button. 2. To input a freeway entrance or exit, touch "Freeway Ent./Exit" on the second page of the "Destination" screen. If the same two streets cross at more than one intersection, the screen changes and displays the menu to select the city name where the - 2010 Toyota Corolla | Navigation Manual - Page 58
list is displayed by touching this button and inputting the name. 3. Input the latitude and the longitude. 4. When the input is finished, touch "OK". By touching the button of the desired point, the screen changes and displays the map location of the selected destination and the route preference - 2010 Toyota Corolla | Navigation Manual - Page 59
DESTINATION SEARCH - Deleting set destinations A set destination can be deleted. 1. Push the "DEST" button. 2. Touch "Del. Dest." on the "Destination" screen. When more than one destination is set, a list will be displayed on the screen. 5. If more than one destination is set, touch "OK" after - 2010 Toyota Corolla | Navigation Manual - Page 60
Starting route guidance After inputting the destination, the screen changes and displays the map location of the selected destination and "Replace " are displayed. "Add to ": To add a destination. "Replace ": To delete the existing destinations and set a new one. "Route Preference": To change the - 2010 Toyota Corolla | Navigation Manual - Page 61
change the route before starting INFORMATION D Guidance can be suspended or resumed. (See "Suspending and resuming guidance" on page 92.) D If "Guide" for the specified location. D When setting the destination on a map with a scale larger than 0.5 miles (800 m), the map scale changes to 0.5 miles - 2010 Toyota Corolla | Navigation Manual - Page 62
Touch "Quick1", "Quick2" or "Short" to select the desired route. "Quick1": Recommended route. This route is indicated by an orange line. "Quick2": Alternative route. This route is indicated by a purple line. "Short": A route by which you can reach the destination in the shortest distance. This route - 2010 Toyota Corolla | Navigation Manual - Page 63
DESTINATION SEARCH 1 2 3 4 5 Time necessary for the entire trip Distance of the entire trip Toll road Freeway Ferry 68 - 2010 Toyota Corolla | Navigation Manual - Page 64
ROUTE GUIDANCE SECTION ROUTE GUIDANCE Route guidance D Route guidance screen D Typical voice guidance prompts D Distance and time to destination D Setting and deleting destination Adding destinations ...Reordering destinations ...Deleting destinations ...D Setting route Search condition ...Detour - 2010 Toyota Corolla | Navigation Manual - Page 65
ROUTE GUIDANCE Route guidance screen During route guidance, various types of guidance screens can be displayed depending on conditions. D Screen layout D During freeway driving During freeway driving, the freeway exit information screen will be displayed. This screen displays the distance to the - 2010 Toyota Corolla | Navigation Manual - Page 66
ROUTE GUIDANCE D When approaching a freeway exit or junction When the vehicle approaches an exit or junction, the guidance screen for the freeway will be displayed. D When approaching an intersection When the vehicle approaches an intersection, the intersection guidance screen will be displayed. - 2010 Toyota Corolla | Navigation Manual - Page 67
ROUTE GUIDANCE D Other screens TURN LIST SCREEN On this screen, the list of turns on the guidance route can be viewed. Touching the turn list. during guidance displays ARROW SCREEN On this screen, information about next turns on the guidance route can be viewed. Touching during guidance displays - 2010 Toyota Corolla | Navigation Manual - Page 68
ROUTE GUIDANCE Typical voice guidance prompts The voice guidance provides various messages as you approach an intersection, or other point where you need to maneuver the vehicle. 4.2 miles 0.25 miles 4.7 miles 0.25 miles +α 1 "Proceed about 4 miles to the traffic circle." "In a quarter of a mile - 2010 Toyota Corolla | Navigation Manual - Page 69
ROUTE GUIDANCE One −way road One −way road ∗: The system indicates a U−turn if the distance between two one−way roads (of opposite directions) is less than 50 feet (15 m) in residential areas or 164 feet (50 m) in non−residential areas. The system announces the approach to the final destination. - 2010 Toyota Corolla | Navigation Manual - Page 70
ROUTE GUIDANCE Distance and time to destination The distance, the estimated travel time and the estimated arrival time from the current position to the selected destination are displayed. Estimated travel time is displayed. Estimated arrival time is displayed. When the vehicle is on the guidance - 2010 Toyota Corolla | Navigation Manual - Page 71
routes can be done. - Reordering destinations When more than one destination is set, you can change the arrival order of the destinations. 1. Touch "Route". 1. Touch "Route". 2. Touch "Add". 3. Input an additional destination in the same way as the destination search. (See "Destination search" on - 2010 Toyota Corolla | Navigation Manual - Page 72
ROUTE GUIDANCE - Deleting destinations 4. After selecting the destinations, touch "OK". The system searches for the guidance route again, and displays the entire route. Even if "OK" is not touched, the entire route is displayed automatically within a few seconds when the order is fixed. A set - 2010 Toyota Corolla | Navigation Manual - Page 73
ROUTE GUIDANCE Setting route - - Search condition 4. To delete the destination(s), touch "Yes". If "Yes" is touched, the data cannot be recovered. If "No" is touched, the previous screen will return. 5. If more than one destination is set, touch "OK" after deleting the destinations. The system - 2010 Toyota Corolla | Navigation Manual - Page 74
the route where a delay is caused by road repairs, or an accident, etc. The entire route from the starting point to the destination is displayed. "Guide": To start guidance. "Route": To change a route. (See pages 76 and 78.) 1. Touch "Route". 2. Touch "Detour". 79 - 2010 Toyota Corolla | Navigation Manual - Page 75
. For details, see "XMr NavTraffic" on page 120. This picture shows an example of how the system would guide around a delay caused by a traffic jam. 1 This position indicates the location of a traffic jam caused by road repairs or an accident. 2 This route indicates the detour suggested by the - 2010 Toyota Corolla | Navigation Manual - Page 76
is set on the freeway, but the vehicle is driven parallel along the freeway.) 1. Touch "Route". 1. Touch "Route". 2. Touch "Route Preference" to change the conditions that determine the route to the destination. 2. Touch "Start from Adjacent Road". When there is no adjacent road, this button will - 2010 Toyota Corolla | Navigation Manual - Page 77
of Point of Interest on the screen. Touch the desired Point of Interest category to display POI location symbols on the map screen. By selecting the desired POI category and then touching "OK", limited choice of Points of Interest will be displayed. (To change the displayed POI, see page 114.) 82 - 2010 Toyota Corolla | Navigation Manual - Page 78
icons" screen. When a Point of Interest category is selected from either the limited list or the complete list, the screen will display symbols of those locations on the map screen. D To display the local POI list Points of Interest that are within 20 miles (32 km) of the current position will - 2010 Toyota Corolla | Navigation Manual - Page 79
and displays the map location of the selected destination and route preference. (See "Starting route guidance" on page 65.) 2. Touch "Route Overview". The entire route from the current position to the destination is displayed. "Guide": To start guidance. "Route": To change the route. (See pages - 2010 Toyota Corolla | Navigation Manual - Page 80
. However, not all road touching names in the route may appear on the list. If a road changes its name without requiring a turn (such as on a street that runs through two or more cities), the name change will not appear on the list. The street names will be displayed in order from the starting - 2010 Toyota Corolla | Navigation Manual - Page 81
ROUTE GUIDANCE - Route trace It is possible to store the traveled route up to 124 miles (200 km) and retrace the route on the display. INFORMATION This feature is available on the map with more detailed map scale than 30 mile (50 km). : To indicate the next destination. : To preview the route to - 2010 Toyota Corolla | Navigation Manual - Page 82
ROUTE GUIDANCE "Record": To start recording the route trace. "Stop": To stop recording the route trace. If you touch "Stop" to display the following screen. Touching "Yes" stops recording and the route trace remains displayed on the screen. Touching "No" stops recording and the route trace is - 2010 Toyota Corolla | Navigation Manual - Page 83
ROUTE GUIDANCE 88 - 2010 Toyota Corolla | Navigation Manual - Page 84
ADVANCED FUNCTIONS SECTION ADVANCED FUNCTIONS Descriptions of functions for more effective use D Quick reference ("Menu" screen) D Quick reference ("Setup" screen) D Suspending and resuming guidance D Volume D User selection 4 90 91 92 93 94 D My places 96 Registering memory points ...97 Editing - 2010 Toyota Corolla | Navigation Manual - Page 85
settings for different users can be memorized...94 6 "XM NavTraffic" Sets XMr NavTraffic information...120 7 "Setup" Enables various settings for the navigation system...91, 110 8 "My Places" Enables changes to "Memory points", "Home" and "Areas to avoid". Enables deletion of the previous point...96 - 2010 Toyota Corolla | Navigation Manual - Page 86
touch "Setup". 1 "Unit of Measurement" The distance units "km" or "miles" can be selected...111 2 "Estimated Travel Time" The system to display the travel time and the arrival time to the destination on the route guidance screen can be set...111 3 "Keyboard Layout" Key layout can be changed...112 - 2010 Toyota Corolla | Navigation Manual - Page 87
...117 12 "Calibration" Adjustment of the current vehicle position mark can be done manually...118 13 "Default" This touch screen button initializes all of the settings...110 14 "?" Function help for the "Setup" screen can be viewed...29 D To suspend guidance 1. Push the "MENU" button. 2. Touch - 2010 Toyota Corolla | Navigation Manual - Page 88
"MENU" button. The voice guidance volume can be adjusted or switched off. 2. Touch "Resume Guidance". 1. Push the "MENU" button. The screen will change to the current position map with route guidance. 2. Touch "Volume". To adjust the volume, select the desired level by touching the appropriate - 2010 Toyota Corolla | Navigation Manual - Page 89
FUNCTIONS User selection INFORMATION During route guidance, the voice guidance continues even if the navigation screen is changed to other screens. "Adaptive Volume Control": By turning "Adaptive Volume Control" on, the volume is turned up automatically when the vehicle speed exceeds 50 mph (80 km - 2010 Toyota Corolla | Navigation Manual - Page 90
ADVANCED FUNCTIONS D To register D To change user 1. Touch "Memorize". The confirmation screen will be displayed. Touch "User number". . When a button that is already registered is touched, the following screen appears. To replace, touch "Yes". To cancel the re. placement, touch "No" or 95 - 2010 Toyota Corolla | Navigation Manual - Page 91
ADVANCED FUNCTIONS My places - D To delete user Points or areas on the map can be registered. The registered points can be used on the "Destination" screen. (See " - Destination search by Home" on page 46, " - Destination search by Quick access" on page 46 and " - Destination search by Memory" on - 2010 Toyota Corolla | Navigation Manual - Page 92
Deleting previous points" on page 110.) 9 Number of remaining memory points 10 Number of remaining areas to avoid 3. Touch "Register". 4. Enter the location in the same way as for a destination search. (See "Destination search" on page 43.) After memory point registration is completed, the "Memory - 2010 Toyota Corolla | Navigation Manual - Page 93
ADVANCED FUNCTIONS - Editing memory points The icon, attribute, name, location and/or telephone number of a registered memory point can be edited. 1. Push the "MENU" button. 2. Touch "My Places" on the "Menu" screen. 5. Touch "OK". To - 2010 Toyota Corolla | Navigation Manual - Page 94
ADVANCED FUNCTIONS D To change "Icon" 1. Touch "Icon" on the "Memory Point" screen. Name": To edit memory point names. The names can be displayed on the map. (See page 101.) "Location": To edit location information. (See page 102.) "Phone #": To edit telephone numbers. (See page 103.) 6. Touch "OK - 2010 Toyota Corolla | Navigation Manual - Page 95
Touch "with Sound" on the "Change Icon" screen. D To change "Quick Access" It is possible to change attributes of the quick access points. the vehicle approaches this point in the direction that has been set. 3. To replace the attribute, touch "Yes". To return to the previous screen, touch "No - 2010 Toyota Corolla | Navigation Manual - Page 96
ADVANCED FUNCTIONS DELETING "Quick Access" D To change "Name" 1. Touch "Name" on the "Memory Point" screen. 1. Touch "Del.". 2. Enter the name using the alphanumeric keys. Up to 24 letters can be entered. 3. Touch " - 2010 Toyota Corolla | Navigation Manual - Page 97
ADVANCED FUNCTIONS DISPLAYING MEMORY POINT NAMES The name of a memory point that may be displayed on the map can be set. D To change "Location" 1. Touch "Location" on the "Memory Point" screen. To show the name, touch "ON" on the "Memory Point" screen. To not show it, touch "OFF". 2. Touch the - 2010 Toyota Corolla | Navigation Manual - Page 98
ADVANCED FUNCTIONS - Deleting memory points D To change "Phone #" (telephone number) 1. Touch "Phone #" on the "Memory Point" screen. 1. Push the "MENU" button. 2. Touch "My Places" on the "Menu" screen. 2. Enter the number using - 2010 Toyota Corolla | Navigation Manual - Page 99
- Registering home If home has been registered, that information can be recalled by using the "Home" touch screen button on the "Destination" memory points" on page 98. 3. Touch "Register". 4. Enter the location in the same way as for a destination search. (See "Destination search" on page - 2010 Toyota Corolla | Navigation Manual - Page 100
Touch "My Places" on the "Menu" screen. 3. Touch "Delete". 4. To delete home, touch "Yes". To cancel the deletion, touch "No". 3. Touch "Register". 4. Enter the location in the same way as for a destination search, or display the map of the area to be avoided. (See "Destination search" on page 43 - 2010 Toyota Corolla | Navigation Manual - Page 101
or to change the size of the area to be avoided. 8. Touch "OK". INFORMATION D If a destination is input in the area to avoid or the route calculation cannot be made without running through the area to avoid, a route passing through the area to be avoided may be shown. D Up to 10 locations can be - 2010 Toyota Corolla | Navigation Manual - Page 102
ADVANCED FUNCTIONS D To change "Name" 1. Touch "Name" on the "Edit Area to Avoid" screen. 5. Touch the button to be edited. "Name": To edit the name of the area to avoid. The names can be displayed on the map. (See page 107.) "Location": To edit area location. (See page 108.) "Area Size": To edit - 2010 Toyota Corolla | Navigation Manual - Page 103
NAMES OF AREAS TO BE AVOIDED The name of an area to be avoided that may be displayed on the map can be set. D To change "Location" 1. Touch "Location" on the "Edit Area to Avoid" screen. To show the name, touch "ON" on the "Edit Area to Avoid" screen. To not show it - 2010 Toyota Corolla | Navigation Manual - Page 104
Area Size" on the "Edit Area to Avoid" screen. 1. Push the "MENU" button. 2. Touch "My Places" on the "Menu" screen. 2. Touch either or to change the size of the area to be avoided. 3. Touch "OK". The previous screen will be displayed. 3. Touch "Delete". 4. Touch the button to be deleted. "Delete - 2010 Toyota Corolla | Navigation Manual - Page 105
Points". 1. Push the "MENU" button. 4. Touch the button you want to delete. "Delete All": To delete all previous points in the system. 2. Touch "Setup". 3. Touch the items to be set. 5. To delete the point, touch "Yes". To cancel the deletion, touch "No". 4. Touch "OK". The previous screen - 2010 Toyota Corolla | Navigation Manual - Page 106
Unit of Measurement Unit of Measurement can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. D time and the estimated arrival time can be set. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. 3. Touch "km" or "miles" of "Unit of Measurement" to - 2010 Toyota Corolla | Navigation Manual - Page 107
by road conditions such as traffic jams, and construction work. D It is possible to display up to 99 hours 59 minutes. Key layout can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. 3. Touch "ABC" or "QWE" of "Keyboard Layout" to choose the input key layout. 112 - 2010 Toyota Corolla | Navigation Manual - Page 108
ADVANCED FUNCTIONS LAYOUT TYPE D Time zone Time zone can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. " "ABC" type 3. Touch "Change" of "Time Zone". The "Adjust Time Zone" screen will be displayed on the display. " "QWE" type The selected button is highlighted. - 2010 Toyota Corolla | Navigation Manual - Page 109
touch screen button and current street name on the map screen can be displayed or hidden. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. D POI category change (Display POI Icons) Select from among the 6 icons displayed on the "Display POI Icons" top screen, so that setting of the - 2010 Toyota Corolla | Navigation Manual - Page 110
map screen using a scale of 150 feet (50 m) to 300 feet (100 m). To turn the "Display Building Shapes" on: 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. 5. Touch the category button to be displayed on the "Display POI Icons" top screen. 6. Touch "OK". Then touch to display page - 2010 Toyota Corolla | Navigation Manual - Page 111
of traffic or seasonal restrictions. To turn the "Traffic Restrict. Notification" on: 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. Then touch to display page 2 of the "Setup" screen. D Voice guidance in all modes When the "Voice Guidance in All Modes" feature is turned on, the - 2010 Toyota Corolla | Navigation Manual - Page 112
guidance can be heard only if the "MAP/VOICE" button is pushed. To turn the "Auto Voice Guidance" mode on: 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. Then touch twice to display page 2 of the "Setup" screen. D Pop−up message When the "Pop−up Message" is turned on, the pop - 2010 Toyota Corolla | Navigation Manual - Page 113
messages will not displayed. D Current position/tire change calibration The current vehicle position mark can be adjusted manually. Miscalculation of the distance caused by tire replacement can also be adjusted. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. Then touch twice - 2010 Toyota Corolla | Navigation Manual - Page 114
When driving, the current vehicle position mark will be automatically corrected by GPS signals. If GPS reception is poor due to location, you can manually adjust the current vehicle position mark. 3. Touch "Enter". 1. Touch "Position/Direction". 4. Touch either or to adjust the direction of the - 2010 Toyota Corolla | Navigation Manual - Page 115
−967−2346. Customers should have their radio ID ready; the radio ID can be found by selecting "channel 000" on the radio. For details, see "Displaying the radio ID" on page 152. All fees and service are the responsibility of the XMr Satellite Radio and are subject to change. To perform a distance - 2010 Toyota Corolla | Navigation Manual - Page 116
. On this screen, the following operations can be performed. 1 Show XMr NavTraffic Information Traffic information is displayed on the map. (See page 122.) 2 Auto Avoid Traffic If any heavy congestion or moderate traffic has been detected on the guidance route, it may be possible for you to select - 2010 Toyota Corolla | Navigation Manual - Page 117
XMr NavTraffic information has been received, the XMr NavTraffic information arrow will appear on the map screen. The color of the arrow changes depending on the traffic information received. "Orange": Heavy congestion "Yellow": Moderate traffic "Green": Freely flowing traffic " Freeway information - 2010 Toyota Corolla | Navigation Manual - Page 118
NavTraffic indicator will appear on the screen. The color of the indicator changes depending on the traffic information received. "White": guidance. (b) Auto Avoid Traffic The guidance route automatically changes to another route to avoid heavy congestion. Touch "ON" of the "Auto Avoid Traffic". - 2010 Toyota Corolla | Navigation Manual - Page 119
ADVANCED FUNCTIONS (c) Traffic Voice Guidance You can receive congestion information through voice guidance while being guided to your destination. (d) Show Free Flowing Traffic Freely flowing traffic is shown with the arrow. Touch "ON" of the "Traffic Voice Guidance". Touch "ON" of - 2010 Toyota Corolla | Navigation Manual - Page 120
(e) XMr NavTraffic text information When you touch the XMr NavTraffic icon on the map, the XMr NavTraffic info. bar will appear on the upper part of the screen. 1. Touch "Info." to display the "Traffic Information" screen. 2. Touch "Detail" to display detailed traffic event information. 125 - 2010 Toyota Corolla | Navigation Manual - Page 121
ADVANCED FUNCTIONS 126 - 2010 Toyota Corolla | Navigation Manual - Page 122
OTHER FUNCTIONS SECTION OTHER FUNCTIONS Other functions D Maintenance information Maintenance information setting ...Dealer setting ...D Calendar with memo Adding a memo ...Editing a memo ...Memo list ...D Screen adjustment D Screen setting D Beep setting D Selecting a language 5 128 128 130 132 - 2010 Toyota Corolla | Navigation Manual - Page 123
navigation system is turned on, the "Information" screen displays when it is time to replace a part or certain components. (See page 24.) 1. Push the "INFO" button. 2. Touch " screen is disabled. When the vehicle needs to be serviced, the touch screen button color will change to orange. 128 - 2010 Toyota Corolla | Navigation Manual - Page 124
": Replace tires "BATTERY": Replace battery "BRAKE PAD": Replace brake linings "WIPERS": Replace wiper blades "LLC": Replace engine coolant "BRAKE OIL": Replace brake fluid "ATF": Replace ATF (Automatic Transmission Fluid) "SERVICE": Scheduled maintenance "AIR FILTER": Replace air filter "PERSONAL - 2010 Toyota Corolla | Navigation Manual - Page 125
": To set the displayed dealer as a destination. (See "Starting route guidance" on page 65.) 4. If the dealer has not been registered, enter the location of the dealer in the same way as for a destination search. (See "Destination search" on page 43.) When "Set Dealer" registration is finished, the - 2010 Toyota Corolla | Navigation Manual - Page 126
OTHER FUNCTIONS D To edit "Dealer" or "Contact" 1. Touch "Dealer" or "Contact" on the "Edit Dealer" screen. D To edit "Location" 1. Touch "Location" on the "Edit Dealer" screen. 2. Enter the name using the alphanumeric keys. Up to 24 letters can be entered. 3. Touch "OK". The previous screen will - 2010 Toyota Corolla | Navigation Manual - Page 127
entry when the system is turned on. (See page 25.) Memos can also be used for route guidance if the memo has been registered with location information. 2. Enter the number using number keys. 3. Touch "OK". The previous screen will be displayed. 1. Push the "INFO" button. 2. Touch "Calendar". 132 - 2010 Toyota Corolla | Navigation Manual - Page 128
of the mark displayed next to the date. To default the mark color, touch "Delete" on the "Mark color" screen. "Date f": To change the color of the date. To default the date color, touch "Delete" on the "Date color" screen. "Prev. Day": To go to the "Memo" screen of the previous date. "Today": To - 2010 Toyota Corolla | Navigation Manual - Page 129
bottom right of the screen. 4. Touch "Add Memo". Up to 100 memos can be added. 7. When registering information on the memo, touch "Location". A screen similar to the destination search screen appears. Search the same way as searching a destination. (See "Destination search" on page 43.) 5. Touch - 2010 Toyota Corolla | Navigation Manual - Page 130
the item to be edited. "Memo": To edit a memo. (See " - Adding a memo" on page 134.) "Location": To change a registered location. (See " - Adding a memo" on page 134.) "Enter ": To set the registered location as a destination. (See "Starting route guidance" on page 65.) "Delete": To delete the memo - 2010 Toyota Corolla | Navigation Manual - Page 131
OTHER FUNCTIONS D To display memos for a specified period of time 1. Touch "Period" on the "Memo Search" screen. 5. To delete and/or edit the memo, touch the desired memo button. "Delete All": To delete all the displayed memos. A message will be displayed. 6. To delete, touch "Yes". To cancel the - 2010 Toyota Corolla | Navigation Manual - Page 132
contrast of the screen. You can also turn the display off, and change the screen to either day or night mode. D Contrast and brightness OK". The screen goes off when "Screen Off" is touched. To turn the display screen back on, push any button such as "DISP/TILT", etc. The selected screen appears. 1. - 2010 Toyota Corolla | Navigation Manual - Page 133
the day mode even with the headlight switch on, touch "Day Mode" on the adjustment screen for brightness and contrast control. If the screen is set in the day mode with the headlight switch turned on, this condition is memorized in the system even with the engine turned off. 2. Touch "Screen Setting - 2010 Toyota Corolla | Navigation Manual - Page 134
(a) Automatic transition You can select a function that enables automatic return to the navigation screen from the audio screen. (b) Switch color You can select the color of the touch screen buttons. Select "ON" or "OFF" and then touch "OK". "ON": The navigation screen automatically returns - 2010 Toyota Corolla | Navigation Manual - Page 135
OTHER FUNCTIONS (c) Delete personal data The following personal data can be deleted or returned to their default settings: D Maintenance conditions D Maintenance information "off" setting D Memory points D Areas to avoid D Previous points D Route trace D User selection settings This function is - 2010 Toyota Corolla | Navigation Manual - Page 136
You can set a beep sound off. Selecting a language The language of the touch screen buttons, pop−up messages and the voice guidance can be changed. 1. Push the "INFO" button. 1. Push the "INFO" button. 2. Touch "Beep Off". "Beep Off" is highlighted. To switch the beep sound on, touch "Beep Off - 2010 Toyota Corolla | Navigation Manual - Page 137
çais" or "Español" to select a language. If a screen other than for the navigation system is displayed, the current screen would change to the "CAUTION" screen by pushing the "MAP/VOICE", "DEST" or "MENU" button. 4. Touch "OK". The language is changed and the screen returns to the map display. 142 - 2010 Toyota Corolla | Navigation Manual - Page 138
AUDIO SYSTEM SECTION AUDIO SYSTEM Audio system D Quick reference D Using your audio system Some basics ...Radio operation ...CD player operation ...D Audio remote controls D Audio system operating hints 6 144 145 145 149 158 169 170 143 - 2010 Toyota Corolla | Navigation Manual - Page 139
button. 1 2 Function menu display screen To control the radio or CD player, touch the touch screen control screen. For details, see page 146. " " button Push this button to insert or eject a disc. For details, see pages 158 and 160. "DISC·AUX" button Push this button to turn the CD player and AUX - 2010 Toyota Corolla | Navigation Manual - Page 140
STOP" switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system - Your audio system works when the engine switch is in "ACC" or "ON" position. CAUTION For vehicles sold in U.S.A. and Canada: D Part 15 of the FCC Rules FCC Warning: Changes or modifications in construction not - 2010 Toyota Corolla | Navigation Manual - Page 141
"AUDIO": Push this button to display touch screen buttons for audio system (audio control mode). "PWR·VOL": Push this knob to turn the audio system on and " on page 139 for details. Push "AM·SAT", "FM" or "DISC·AUX" button to turn on the desired mode. The selected mode turns on immediately. Push - 2010 Toyota Corolla | Navigation Manual - Page 142
AUDIO SYSTEM Touch them lightly and directly on the screen. The selected button is highlighted. INFORMATION D If the system does not respond to a touch cleaning cloth. The function buttons for radio and CD player operation are displayed on the screen when the audio control mode is selected. 147 - 2010 Toyota Corolla | Navigation Manual - Page 143
channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the volume of one group of sounds while decreasing the volume of another. 1. Push the "AUDIO" button. 3. Touch - 2010 Toyota Corolla | Navigation Manual - Page 144
is intended for use with 12 cm (4.7 in.) discs only. D AUX adapter The sound of portable audio players connected to the AUX adapter can be enjoyed. Push the "DISC·AUX" button to switch to AUX mode. For details, refer to the "Owner's Manual". Push these buttons to choose either an AM or FM station - 2010 Toyota Corolla | Navigation Manual - Page 145
up or step down the station band. Your radio automatically changes to stereo reception when a stereo broadcast is received. separation to prevent the weak signal from creating noise. If the signal becomes extremely weak, the store up to 6 stations. To change the preset station to a different one, - 2010 Toyota Corolla | Navigation Manual - Page 146
customer service agreement. Customers should have their radio ID ready; the radio ID can be found by selecting "channel 000" on the radio. For details, see the "Displaying the radio ID" that follows. All fees and programming are the responsibility of the XMr Satellite Radio and are subject to change - 2010 Toyota Corolla | Navigation Manual - Page 147
radio ID when activating XMr service or when reporting a problem. If you select the "CH 000" using the "TUNE·SEEK/TRACK" button, the ID code of 8 alphanumeric characters appears. If you select another channel, display of the ID code is canceled. The channel (000) alternates - 2010 Toyota Corolla | Navigation Manual - Page 148
button and the name and number of the channel appears on the touch screen button. Each touch screen button can store three SAT channels. To change the preset channel to a different one, follow the same procedure. The preset channel memory is cancelled when the power source is interrupted by - 2010 Toyota Corolla | Navigation Manual - Page 149
AUDIO SYSTEM D Selecting a channel Tune in the desired channel using one of the following methods. Preset tuning: Touch the channel selector button (1 - 6) for the channel you want. The button (1 - 6) is highlighted and channel number appears on the display. To select channel within the current - 2010 Toyota Corolla | Navigation Manual - Page 150
AUDIO SYSTEM D Displaying the title and name When you touch "TEXT", the song/program title and the artist name/feature are displayed. Up to 16 alphanumeric characters can be displayed. (Some information will not be fully displayed.) When you touch "TEXT" again, the display returns. 155 - 2010 Toyota Corolla | Navigation Manual - Page 151
problem, take the suggested corrective action. The XMr antenna is not connected. Check CH000" and all free−to−air channels. UPDATING The premium "CH001". If it does not change automatically, select another channel. If you the current location. Wait until your vehicle reaches a location with a - 2010 Toyota Corolla | Navigation Manual - Page 152
equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of Alternation or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment. INFORMATION This XMr tuner supports "Audio Services - 2010 Toyota Corolla | Navigation Manual - Page 153
"Audio system operating hints" on page 170. (a) Inserting discs Vehicles with smart key system - The "ENGINE START STOP" switch must be set at ACCESSORY or IGNITION ON mode. Vehicles without smart key system - The engine switch must be set at "ACC" or "ON" position. 1. Push the " " button. 158 - 2010 Toyota Corolla | Navigation Manual - Page 154
such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident. D To reduce the chance of injury in case of faces down, the disc cannot be played. In this case, "CD Check" appears on the screen. NOTICE Do not obstruct the display while it is - 2010 Toyota Corolla | Navigation Manual - Page 155
(b) Ejecting discs (c) Playing a disc Push the " " button. The display will open and the disc will be ejected. A disc can then be inserted. Push the "DISC·AUX" button if the disc are already loaded in the CD player. The "CD" screen will be displayed. NOTICE If a disc cannot be ejected, do not - 2010 Toyota Corolla | Navigation Manual - Page 156
AUDIO SYSTEM (d) Operating an audio CD D Playing an audio CD D Selecting a desired track Push the "AUDIO" button to display this screen. "TUNE·SEEK/TRACK" button: Use for a direct access to a desired track. Push " " or " " sides of the "TUNE·SEEK/TRACK" button and repeat it until the desired - 2010 Toyota Corolla | Navigation Manual - Page 157
AUDIO SYSTEM D Searching for a desired track Touch the desired track number. The CD player will start playing the selected track from the beginning. : By touching this button, the list moves up by 6 track groups. If this button is touched when the top page of the list is displayed, the last page - 2010 Toyota Corolla | Navigation Manual - Page 158
to. While the track is playing, touch "RPT" briefly. "RPT" appears on the screen. When the track is finished, the CD player will automatically go back to the beginning of the track and play the track again. To cancel it, touch "RPT" once again. 163 - 2010 Toyota Corolla | Navigation Manual - Page 159
AUDIO SYSTEM (e) Operating a MP3/WMA disc D Playing a MP3/WMA disc D Selecting a desired folder "FOLDERY": Touch this button to go to the next folder. "FOLDERB": Touch this button to go to the previous folder. "FOLDER LIST": The desired folder can be selected in a list. This function is available - 2010 Toyota Corolla | Navigation Manual - Page 160
AUDIO SYSTEM D Selecting a desired file "FILE": The desired file can be selected in a list. This function is available only when the vehicle is not moving. Touch "FILE". The file list is displayed. "TUNE·SEEK/TRACK" button: Use for direct access to a desired file. Push " " or " " sides of the " - 2010 Toyota Corolla | Navigation Manual - Page 161
AUDIO SYSTEM D Searching for a desired file Touch the desired file number. The CD player will start playing the selected file from the beginning. : By touching this button, the list moves up by 6 file groups. If this button is touched when the top page of the list is displayed, the last page is - 2010 Toyota Corolla | Navigation Manual - Page 162
a file - While the file is playing, touch"RPT" briefly. "RPT" appears on the screen. When the file is finished, the CD player will automatically go back to the beginning of the file and play the file again. To cancel it, touch "RPT" once again. Repeating a folder - While the folder is playing - 2010 Toyota Corolla | Navigation Manual - Page 163
insert it correctly. If a disc which is not playable is inserted, "CD Check" will also appear on the screen. For appropriate discs for this player, appears on the display: The following causes are possible. D There is a trouble inside the system. Eject the disc. D The inside of the player unit may - 2010 Toyota Corolla | Navigation Manual - Page 164
" switch Each time you push the "MODE" switch, the system changes the audio mode. To turn the audio system on, push the parts of the audio system can be adjusted with the switches on the steering wheel. Details of the specific switches, controls, and features are described below. 1 Volume control - 2010 Toyota Corolla | Navigation Manual - Page 165
alternately noise, wires can interfere with AM signals. And of course, radio signals have a limited range, and the farther you are from a station, the weaker its signal will be. In addition, reception conditions change constantly as your vehicle moves. Here are some common reception problems - 2010 Toyota Corolla | Navigation Manual - Page 166
). D The MP3/WMA player plays back files with .mp3 or .wma file extensions as MP3 or WMA files. To prevent noise and playback errors, use the appropriate if fast−forward or reverse operations are used. It is not possible to check folders that do not include MP3/WMA files. MP3/WMA files in folders - 2010 Toyota Corolla | Navigation Manual - Page 167
AUDIO SYSTEM CD−R AND CD−RW DISCS D CD−R/CD−RW discs that have not 001.mp3 002.wma Folder 1 003.mp3 Folder 2 004.wma 005.mp3 Folder 3 006.mp3 D D The play order of the compact disc with the structure shown on the left is as follows: D D D D been subject to the "finalizing process" (a - 2010 Toyota Corolla | Navigation Manual - Page 168
player is intended for use with 12 cm (4.7 in.) discs only. D Extremely high temperature can keep your CD player from working. On hot days, use air conditioning to cool the vehicle interior before you listen to a disc. D Bumpy roads or other vibrations may make your CD player skip. D If moisture - 2010 Toyota Corolla | Navigation Manual - Page 169
AUDIO SYSTEM " Special shaped discs " Labeled discs NOTICE D Do not use special shaped, transparent/translucent, low quality or labeled discs such as those shown in the illustrations. The use of such discs may damage the player or changer, or it may be impossible to eject the disc. D This system - 2010 Toyota Corolla | Navigation Manual - Page 170
skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.) D Remove discs from the players when you are not using them. Store them in their plastic cases away from moisture soft, lint−free cloth. Do not use a conventional record cleaner or anti−static device. 175 - 2010 Toyota Corolla | Navigation Manual - Page 171
with ID3 tag editing functions. Although the tags are restricted to the number of characters, the information can be viewed when the track is played back. WMA Tag- WMA files can contain a WMA tag that is used in the same way as an ID3 tag. WMA tags carry information such as - 2010 Toyota Corolla | Navigation Manual - Page 172
APPENDIX SECTION APPENDIX Appendix D Limitations of the navigation system D Map database information and updates 7 178 180 177 - 2010 Toyota Corolla | Navigation Manual - Page 173
APPENDIX Limitations of the navigation system This navigation system calculates the current vehicle position using satellite signals, various vehicle signals, map data, etc. However, the accurate position may not be shown depending on the satellite condition, road configuration, vehicle condition - 2010 Toyota Corolla | Navigation Manual - Page 174
or left. D It may take a long time to operate auto reroute during high speed driving. In auto reroute, a detour route may be shown. D After auto reroute, the route may not be changed. D An unnecessary U−turn may be shown or announced. D A location may have multiple names and the system will announce - 2010 Toyota Corolla | Navigation Manual - Page 175
APPENDIX Map database information and updates - After replacing a tire, implement the operation described in the "TIRE CHANGE CALIBRATION". (See page 120.) This navigation system uses tire turning data and is designed to work with factory− specified tires for your vehicle. Installing tires - 2010 Toyota Corolla | Navigation Manual - Page 176
OF THE SPATIAL MAP DATABASE, INCLUDING LOCATION CODES AND RELATED PRODUCTS (COLLECTIVELY, THE extract stand−alone data from or publish any part of the DATABASE without the prior written consent copy, duplicate, modify, adapt, translate, disassemble, decompile, or reverse engineer any portion of the - 2010 Toyota Corolla | Navigation Manual - Page 177
A WARRANTY, AND YOU ARE NOT ENTITLED TO RELY ON ANY SUCH ADVICE OR INFORMATION. THIS DISCLAIMER OF WARRANTIES IS AN information due to the passage of time, changing circumstances, and due to the nature of the ; road slope or grade; bridge height, weight or other limits; road or traffic conditions; - 2010 Toyota Corolla | Navigation Manual - Page 178
data − commercial items clause); FAR 52.227−14 Alternates I, II, and III (JUN 1987) (civilian limitations on the Government's rights shall control. Contractor/manufacturer is Tele Atlas North clause void and unenforceable, in whole or in part, for any reason, this Agreement shall be considered - 2010 Toyota Corolla | Navigation Manual - Page 179
ServiceR to publish and sell ZIP+4R information. ©United States Postal ServiceR 2007. Prices are not established, controlled or approved by the United States Postal ServiceR otherwise reproduce, copy, modify, decompile, disassemble or reverse engineer any portion of this Data, and may not transfer or - 2010 Toyota Corolla | Navigation Manual - Page 180
. The Data may contain inaccurate or incomplete information due to the passage of time, changing circumstances, sources used and the nature of collecting comprehensive geographic data, any of which may lead to incorrect results. No Warranty. This Data is provided to you "as is," and you agree to use - 2010 Toyota Corolla | Navigation Manual - Page 181
APPENDIX Export Control. You agree not to export from anywhere any part of the Data provided to you or any direct product thereof except in compliance with, and , federal government agency,or any federal official must notify NAVTEQ prior to seeking additional or alternative rights in the Data. 186 - 2010 Toyota Corolla | Navigation Manual - Page 182
in the navigation system is in part provided by infoUSA Inc. ("infoUSA"). copy, modify, adapt, translate, disassemble, decompile, or reverse engineer any portion of purposes, and not for service bureau, time−sharing or management or similar applications. No Warranty. This information is provided to - 2010 Toyota Corolla | Navigation Manual - Page 183
OR CONDITIONS, WHETHER IN AN ACTION IN CONTRACT OR TORT OR BASED ON A WARRANTY, EVEN IF DENSO OR ITS LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF . However, the names of roads, streets, facilities, and their locations frequently change. In some places, construction on roads may be in progress. - 2010 Toyota Corolla | Navigation Manual - Page 184
APPENDIX - Changing the map DVD−ROM 1. Push the "MENU" button. 4. Insert the new map DVD−ROM with the label side up. 5. Push the "CLOSEY" button to close the display. 2. Touch "Map DVD". 3. Touch " DVD". 189 - 2010 Toyota Corolla | Navigation Manual - Page 185
be thrown about and possibly injure people in the vehicle during sudden braking or in an accident. D To reduce the chance of injury in DVD−ROM will be ejected. 2. Touch "Map DVD". INFORMATION Under extremely cold conditions, the display may react slowly or operation sound may become louder. - 2010 Toyota Corolla | Navigation Manual - Page 186
manual carefully to ensure proper use. Keep this manual in your vehicle at all times. The Navigation System is one of the most technologically advanced vehicle accessories will guide you there. The system will provide both a visual map and audio instructions. The audio instructions will announce - 2010 Toyota Corolla | Navigation Manual - Page 187
COROLLA_Navi_U(L/O 0902) Please be aware that all current vehicle navigation systems have certain limitations that may affect their ability to perform properly. The accuracy of the vehicle's position depends on the satellite condition, road configuration, vehicle condition or other circumstances. - 2010 Toyota Corolla | Navigation Manual - Page 188
to make sure you understand the system. Do not allow other people to use this system until they have read and understood the instructions in this manual. For your safety, some functions may become inoperable when driving. Unavailable touch screen buttons are dimmed. Only when the vehicle is not - 2010 Toyota Corolla | Navigation Manual - Page 189
change. Therefore, before following any instruction from the system, look to see whether the instruction services. If unsure about the safety of an area, do not drive into it. Under no circumstances is this system a substitute for the driver's personal judgement. Use this system only in locations - 2010 Toyota Corolla | Navigation Manual - Page 190
Quick guide - - Overview buttons and guidance screen 0U5111aX No. 1 2 Name North−up or heading−up symbol Scale indicator "MAP/VOICE" button "DEST" button "MENU" button "DISP/TILT" button Function This symbol indicates a map view with north−up or heading−up. Touching this symbol changes the map - 2010 Toyota Corolla | Navigation Manual - Page 191
position or the cursor position as a memory point. Touch this button to change the route. Touch this button to browse information about guidance route, to to display the foot print map and the building information. Touch this button to change the screen mode. Page 128, 132, 138, 141 37 31 76, 78 82 - 2010 Toyota Corolla | Navigation Manual - Page 192
- Registering home 1 Push the "DEST" button. 0U5113X 2 Touch . If home has not been registered, you can register it by touching . 3 There are 11 different methods to search your home. See "Destination search" on page 43. 4 Touch "Enter". The "Memory Point" screen is displayed. 7 - 2010 Toyota Corolla | Navigation Manual - Page 193
5 Touch "OK". Registration of home is complete. You can also register home by pushing the "MENU" button. (See " - Registering home" on page 104.) You can change the icon, quick access, name, location and phone number. (See " - Editing memory points" on page 98.) 8 - 2010 Toyota Corolla | Navigation Manual - Page 194
- Registering preset memory points (Quick access) 1 Push the "DEST" button. 0U5112X 2 Touch one of the quick access buttons. You can set a memory point to one of the quick access buttons which has not been set. 3 There are 12 different methods to search preset memory points. See "Destination - 2010 Toyota Corolla | Navigation Manual - Page 195
You can also register preset memory points by pushing the "MENU" button. (See " - Registering memory points" on page 97.) You can change the icon, quick access, name, location and phone number. (See " - Editing memory points" on page 98.) The registered points can be used on the "Destination" screen - 2010 Toyota Corolla | Navigation Manual - Page 196
methods to search destinations. See "Destination search" on page 43. 3 Touch "Enter". The navigation system performs a search for the route. 4 Touch "Guide", and start driving. Routes other than the one recommended can also be selected. (See "Starting route guidance" on page 65.) 5 Guidance - 2010 Toyota Corolla | Navigation Manual - Page 197
. (To register "Home", see " - Registering home" on page 104.) 3 Touch "Enter". The navigation system performs a search for the route. 4 Touch "Guide", and start driving. Routes other than the one recommended can also be selected. (See "Starting route guidance" on page 65.) 5 Guidance to the