Acer Altos R5250 User Manual

Acer Altos R5250 Manual

Get Acer Altos R5250 PDF manuals and user guides View all Acer Altos R5250 manuals
Add to My Manuals
Save this manual to your list of manuals

Acer Altos R5250 manual content summary:

  • Acer Altos R5250 | User Manual - Page 1
    Acer Altos R5250 Series User's Guide
  • Acer Altos R5250 | User Manual - Page 2
    Acer Altos R5250 Series User's Guide Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual affixed to your server. All correspondence concerning
  • Acer Altos R5250 | User Manual - Page 3
    : Phone number: Fax number: Server R5250 Acer America Corporation 333 West San Carlos St., San Jose, CA 95110, U. S. A. Acer Representative 1-254-298-4000 1-254 and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of
  • Acer Altos R5250 | User Manual - Page 4
    not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this server. Use conditions This part complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
  • Acer Altos R5250 | User Manual - Page 5
    v Remarque à l'intention des utilisateurs canadiens Cet appareil numérique de la classe A est conforme a la norme NMB-003 du Canada. Laser compliance statement The CD or DVD drive used with this computer is a laser product. The CD or DVD drive's classification label (shown below) is located on the
  • Acer Altos R5250 | User Manual - Page 6
    Person: Mr. Easy Lai Tel: 886-2-8691-3089 Fax: 886-2-8691-3120 E-mail: [email protected] Hereby declare that: Product: Trade name: Model number: SKU number: Server Acer R5250 R525xx ("x" = 0~9, a~z, A~Z or blank) Is compliant with the essential requirements and other relevant provisions of
  • Acer Altos R5250 | User Manual - Page 7
    vii Declaration of conformity for EU countries Hereby, Acer, declares that this PC series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Russian regulatory certification compliance
  • Acer Altos R5250 | User Manual - Page 8
    Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked . • Unplug the power cord before removing the power supply unit from the server. • If the system has multiple sources of power, disconnect power from the
  • Acer Altos R5250 | User Manual - Page 9
    ix • Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product
  • Acer Altos R5250 | User Manual - Page 10
    4.6 meters (15 feet) maximum length. Safe listening Follow these instructions, suggested by hearing experts,to protect your hearing. • Gradually increase if you can't hear people speaking near you. Product servicing Do not attempt to service this product yourself, as opening or removing covers may
  • Acer Altos R5250 | User Manual - Page 11
    service • the product does not operate normally after following the operating instructions Note: Adjust only those controls that are covered by the operating instructions Electronics Equipment (WEEE) regulations, visit http://global.acer.com/about/ sustainability.htm. Mercury advisory For projectors
  • Acer Altos R5250 | User Manual - Page 12
    xii Tips and information for comfortable use Computer users may complain of eyestrain and headaches after prolonged use. Users are also at risk of physical injury after long hours of working in front of a computer. Long work periods, bad posture, poor work habits, stress, inadequate working
  • Acer Altos R5250 | User Manual - Page 13
    xiii Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following items provide suggestions on how to reduce eyestrain. • Eyes •
  • Acer Altos R5250 | User Manual - Page 14
    xiv Developing good work habits Develop the following work habits to make your computer use more relaxing and productive: • Take short breaks regularly and often. • Perform some stretching exercises. • Breathe fresh air as often as possible. • Exercise regularly and maintain a healthy body. Warning!
  • Acer Altos R5250 | User Manual - Page 15
    compliance vii Information for your safety and comfort viii Safety instructions viii Tips and information for comfortable use xii 1 requirements 19 Connecting peripherals 20 Turning on the system 21 Power-on problems 22 Configuring the system OS 23 Turning off the system 24 3
  • Acer Altos R5250 | User Manual - Page 16
    xvi Pre-installation instructions 28 Post-installation instructions 28 Opening the server 29 Removing and installing the processor 43 Processor upgrading guidelines 43 Upgrading the system memory 47 Memory module population guidelines 47 Installing an expansion card 51 Installing
  • Acer Altos R5250 | User Manual - Page 17
    88 Initial troubleshooting checklist 89 Hardware diagnostic testing 90 Checking the boot-up status 90 Verifying the condition of the storage devices 91 Confirming loading of the operating system 91 Specific problems and corrective actions 92 Appendix A: Server management tools 97
  • Acer Altos R5250 | User Manual - Page 18
    xviii
  • Acer Altos R5250 | User Manual - Page 19
    1 System tour
  • Acer Altos R5250 | User Manual - Page 20
    The Altos R5250 is a feature-rich server equipped with numerous high performance features to provide easy server set up, remote management, highly reliable shared storage, and handle more demanding database or high transaction applications.
  • Acer Altos R5250 | User Manual - Page 21
    are the key features of the Acer Altos R5250 server. Performance Processor • Two socket F (1207-pin) AMD processor sockets supporting dual- core/quad-core AMD Opteron Memory • Supports up to sixteen DDR2-667 registered ECC modules • Eight DIMM slots per processor • Single-processor supports memory
  • Acer Altos R5250 | User Manual - Page 22
    4 1 System tour • Dual-processor supports memory capacity of 64 GB • Supports dual-channel DDR2 memory per processor • Supports memory sparing technology PCI interface • Full height riser slot • One PCI Express x16 bus slots • One PCI-X 133 slot (optional) • One PCI Express x8 bus slot
  • Acer Altos R5250 | User Manual - Page 23
    basic system function Server management • server management Operating system and management utilities • Operating system options: • Microsoft® Windows® Server 2003 • Microsoft® Windows® Server Enterprise Server 10.0 • SUSE Linux® Enterprise Server 10.0, EM64T • Management utilities • Acer EasyBUILD
  • Acer Altos R5250 | User Manual - Page 24
    6 1 System tour • Acer Server Management (ASM) 8.0 • Acer eBusiness Value Pack (optional) • Acer eBusiness ValueSTOR (optional) Mechanical Chassis • Tool-less chassis design for easy hardware access and configuration • Rack-mount (1U, tray-less) setup option • Weight: 16.8 kg (37.04 lbs) •
  • Acer Altos R5250 | User Manual - Page 25
    bezel allow the system status LEDs to be monitored when the front bezel is closed. The front bezel is removable to allow access to the server's hard drives, peripheral device, and control panel. For details on how to remove the front bezel, see "To remove the front bezel" section on page
  • Acer Altos R5250 | User Manual - Page 26
    hot-plug HDD bays USB ports Non-maskable interrupt (NMI) button Puts the server in a halt-state for diagnostic purposes and allows you to issue a non-maskable the chassis and allows you to locate the server you're working on from behind a rack of servers. Power/sleep button Toggles the system power
  • Acer Altos R5250 | User Manual - Page 27
    Rear panel AB C 9 J Item A B C D E F G H I J D E FG H I Component Power supply module Power supply cooling fan PS2 mouse port PS2 keyboard port Serial port Monitor port USB 2.0 ports Gigabit LAN ports (10/100/1000 Mbps) System ID button PCI slot cover
  • Acer Altos R5250 | User Manual - Page 28
    10 Internal components 1 System tour Item A B C D E Component System fan modules SAS RAID or SAS daughter board slot PCI riser card Air duct Power supply
  • Acer Altos R5250 | User Manual - Page 29
    11 System boards Mainboard The mainboard becomes accessible once you open the system. It should look like the figure shown below. 1 2 5 0 3 4
  • Acer Altos R5250 | User Manual - Page 30
    12 1 System tour No. Code Description 1 KB_MS1 Top: PS/2 mouse port Bottom: PS/2 keyboard port 2 COMA1 Serial port 3 VGA1 Monitor port 4 R_USB1 USB 2.0 ports 5 GLAN1 Gigabit LAN port 1 6 GLAN2 Gigabit LAN port 2 7 SW1 ID switch 8 DIMM C1 - C4 DDR2 sockets for processor 2
  • Acer Altos R5250 | User Manual - Page 31
    I2C_2 I2C connector 30 F_PANEL1 Front panel LED connector 31 IPMI1 BMC module slot 32 U41 XGI Volari Z9s VGA controller 33 U42 Video memory 34 iButton RAID activation key (for SAS RAID daughter board) 35 U3 Gigabit LAN controller 36 PCIE_2 SAS RAID or SAS daughter board slot
  • Acer Altos R5250 | User Manual - Page 32
    14 1 System tour Backplane board The backplane board installed on the rear side of the hot-plug drive bay provides support for both SAS and SATA2 hard drives. No. 1 2 3, 5, 6 4 7 8 9 10 Description System fan connectors SAS backplane sensor connector SAS/SATA2 data cable connectors SGPIO (Serial
  • Acer Altos R5250 | User Manual - Page 33
    LAN port Knowing what each LED indicator signifies can aid in problem diagnosis and troubleshooting. Front panel LED indicators The six LED indicators mounted on . Blinking Network connection is established and is running at supported speed. Off Network connection is not established. On HDD
  • Acer Altos R5250 | User Manual - Page 34
    * The status/fault LED indicator is only enabled when the optional BMC module is installed on the mainboard. To purchase this option, contact your local Acer representative. Hot-plug HDD LED indicator A drive activity LED indicator is mounted on the hot-plug HDD carrier. The table below lists the
  • Acer Altos R5250 | User Manual - Page 35
    2 System setup
  • Acer Altos R5250 | User Manual - Page 36
    This chapter gives you instructions on how to set up the system. Procedures on how to connect peripherals are also explained.
  • Acer Altos R5250 | User Manual - Page 37
    air conditioners, radio and TV transmitters, etc. Checking the package contents Check the following items from the package: • Acer Altos R5250 server system • Acer EasyBUILDTM • Acer Altos R5250 accessory box If any of the above items are damaged or missing, contact your dealer immediately. Save the
  • Acer Altos R5250 | User Manual - Page 38
    20 2 System setup Connecting peripherals Refer to the illustration below for specific connection instructions on the peripherals you want to connect to the system. Note: Consult the operating system manual for information on how to configure the network setup.
  • Acer Altos R5250 | User Manual - Page 39
    21 Turning on the system After making sure that you have properly set up the system, applied power, and connected all necessary peripherals, you can now power on the system. To power on the system: 1 Remove the front bezel (A). 2 Press the power button (B). B A The system starts up and displays a
  • Acer Altos R5250 | User Manual - Page 40
    22 2 System setup Power-on problems If the system does not boot after you have applied power, check the following factors that might have caused the boot failure. • The external power
  • Acer Altos R5250 | User Manual - Page 41
    23 Configuring the system OS The Acer Altos R5250 server comes with Acer EasyBUILD that allows you to conveniently close the disc tray. 6 The Acer EasyBUILD sequence begins. Follow all onscreen instructions. For more information, refer to the EasyBUILD Installation guide. Note: Windows or Linux OS CD
  • Acer Altos R5250 | User Manual - Page 42
    Turning off the system There are two ways to turn off the server-via software or via hardware. The software procedure below applies to a the system via hardware: If you cannot shut down the server using the software, press the power button for at least four seconds. Quickly pressing the button may
  • Acer Altos R5250 | User Manual - Page 43
    3 System upgrade
  • Acer Altos R5250 | User Manual - Page 44
    This chapter discusses the precautionary measures and installation procedures you need to know to upgrade the system.
  • Acer Altos R5250 | User Manual - Page 45
    ESD precautions along with pre-installation and post-installation instructions. ESD precautions Electrostatic discharge (ESD) can damage the processor, disk drives, expansion boards, motherboard, memory modules and other server components. Always observe the following precautions before you install
  • Acer Altos R5250 | User Manual - Page 46
    a flat, stable surface. 5 Open the system according to the instructions on page 29. 6 Follow the ESD precautions described in this section when handling a server component. Post-installation instructions Perform the steps below after installing a server component. 1 See to it that all components are
  • Acer Altos R5250 | User Manual - Page 47
    you proceed, make sure that you have turned off the system and all peripherals connected to it. Read the "Pre-installation instructions" on page 28. You need to open the server before you can install additional components. The front bezel and top cover are removable to allow access to the system
  • Acer Altos R5250 | User Manual - Page 48
    30 3 System upgrade To install the front bezel: 1 Line up the center notch on both ends of the bezel with the center guide on the rack handles. 2 Slide the front bezel onto the chassis until it clicks into place.
  • Acer Altos R5250 | User Manual - Page 49
    31 Removing and installing the top cover To remove the top cover: 1 Perform the pre-installation instructions described on page 28. 2 Remove the screw located on the top cover (A). 3 Press and hold the release button (B), then slide the cover toward the back
  • Acer Altos R5250 | User Manual - Page 50
    32 3 System upgrade To install the top cover: 1 Perform the pre-installation instructions described on page 28. 2 Place the top cover on the chassis so that the tabs on the cover align with the slots on the chassis. 3
  • Acer Altos R5250 | User Manual - Page 51
    remove the air duct: You will need to remove the air duct to perform the following procedures: • Removing and installing a processor • Removing and installing the memory modules 1 Perform the pre-installation instructions described on page 28. 2 Lift the air duct from the chassis.
  • Acer Altos R5250 | User Manual - Page 52
    34 3 System upgrade To install the air duct: 1 Perform the pre-installation instructions described on page 28. 2 Place the air duct over the two processor sockets. The front or unplug cables that may be near or under the air duct. 3 Observe the post-installation instructions described on page 28.
  • Acer Altos R5250 | User Manual - Page 53
    support up to three 3.5-inch hot-plug SAS/SATA2 hard disk drives. Removing and installing a hard disk drive Note: Use only Acer local Acer representative. Caution! To ensure proper airflow and server cooling 2 Remove the front bezel. Perform the instructions described in "To remove the front bezel"
  • Acer Altos R5250 | User Manual - Page 54
    described on page 28. For instructions on how to install a new hard disk, refer to the next section. To install an HDD: Note: To puchase a HDD carrier, contact your local Acer representative. 1 Perform steps 1 through 6 described in the "To remove an HDD" section on page 35. 2 If necessary
  • Acer Altos R5250 | User Manual - Page 55
    . 6 Use the lever to push the HDD carrier until it docks into place, then close the HDD carrier lever (B). A B 7 Install the front bezel. Perform the instructions described in "To install the front bezel" section on page 29. 8 Setup the new hard drive's RAID configuration. For related
  • Acer Altos R5250 | User Manual - Page 56
    , unplug the AC power cord from the system, and turn off all peripherals devices connected to the server. To install a slim-line optical drive: 1 Perform the pre-installation instructions described on page 28. 2 Remove the access panel. (1) Remove the eight screws that secure the access panel to
  • Acer Altos R5250 | User Manual - Page 57
    39 3 Remove the new drive from its protective packaging. 4 Install the interposer board on the rear of the optical drive (C), then secure it with the two screws (D). 5 Align the two holes at the left edge of the optical drive with the cutouts in the chassis, then secure it with the two screws (E). D
  • Acer Altos R5250 | User Manual - Page 58
    panel toward the front of the chassis until it is fully closed (A). (2) Secure it with the eight screws you removed earlier (B). 8 Observe the post-installation instructions described on page 28.
  • Acer Altos R5250 | User Manual - Page 59
    41 To remove a slim-line optical drive: 1 Perform the pre-installation instructions described on page 28. 2 Remove the front bezel. Perform the instructions described in "To remove the front bezel" section on page 29. 3 Remove the access panel. Perform step 2 described in the "To install a slim-line
  • Acer Altos R5250 | User Manual - Page 60
    42 3 System upgrade Replacing a system fan Altos R5250 system includes six dual-rotor easy-swap system fan modules to provide adequate airflow and keep system running cool. To replace the system fan: 1 Perform the pre-installation instructions described on page 28. Warning! The system fan becomes
  • Acer Altos R5250 | User Manual - Page 61
    processor Processor upgrading guidelines The server supports two socket F (1207-pin) processor sockets supporting dual-core or quad-core functioning properly. To upgrade the default processor: 1 Perform the pre-installation instructions described on page 28. Warning! The heat sink becomes very hot
  • Acer Altos R5250 | User Manual - Page 62
    44 3 System upgrade 3 Remove the heat sink. (1) Loosen the two screws on the heat sink (A). (2) Pull the heat sink away from the CPU (B). B A CPU2 CPU1 (3) Lay down the heat sink in an upright position-with the thermal patch facing upward. Do not let the thermal patch touch the work surface.
  • Acer Altos R5250 | User Manual - Page 63
    pad to wipe off the old thermal grease from both the HSF assembly and the processor socket retention plate. (2) Apply a thin layer of an Acer-approved thermal interface material before installing the HSF. Make sure that only a very thin layer is applied so that both contact surfaces are still
  • Acer Altos R5250 | User Manual - Page 64
    another. (4) Gradually and equally tighten each captive screw until each is firmly tightened. B A CPU2 CPU1 10 Observe the post-installation instructions described on page 28. To install a second processor: 1 Perform steps 1 through 3 of the previous section. 2 Prepare the processor 2 socket
  • Acer Altos R5250 | User Manual - Page 65
    47 Upgrading the system memory Acer Altos R5250 server supports sixteen DDR2 DIMM slots. The DIMM slots support dual channel DDR2-667 registered ECC memory modules. Important: When you are using a single-processor server, you should install a pair of identical modules into the DIMM A1 and B1, DIMM
  • Acer Altos R5250 | User Manual - Page 66
    organization must be installed in the same colored DIMM slots. • Observe the population sequence in the table below when installing a memory module in a single processor or dual-processor configuration. Single processor configuration DIMM A1/B1 2 x 1 GB 2 x 1 GB 2 x 1 GB 2 x 1 GB 2 x 2 GB 2 x 2 GB
  • Acer Altos R5250 | User Manual - Page 67
    easily into the socket, you may have inserted it incorrectly. Reverse the orientation of the DIMM and insert it again. 6 Observe the post-installation instructions described on page 28. 7 Reconfigure the system memory. See 'To reconfigure the system memory" section on page 50 for more information.
  • Acer Altos R5250 | User Manual - Page 68
    previous section for related procedure, otherwise reinstall the air duct, then observe the post-installation instructions described on page 28. To reconfigure the system memory: The system automatically detects the amount of memory installed. Run the BIOS setup to view the new value for total system
  • Acer Altos R5250 | User Manual - Page 69
    51 Installing an expansion card To install an expansion card: 1 Perform the pre-installation instructions described on page 28. 2 Remove the PCI riser assembly. (1) Loosen the thumbscrew on the metal bracket (A). (2) Gently pull the riser assembly to disengage from the
  • Acer Altos R5250 | User Manual - Page 70
    the thumbscrew to secure the assembly to the chassis (D). C D 7 Connect the necessary cables to the PCI card as required. 8 Observe the post-installation instructions described on page 28. When you turn on the system, the BIOS setup automatically detects and assigns resources to the new device
  • Acer Altos R5250 | User Manual - Page 71
    on how to install a SAS daughter board and a SAS RAID daughter board. To install the SAS daughter board: 1 Perform the pre-installation instructions described on page 28. 2 Locate the SAS daughter board slot. 3 Remove the SAS daughter board from its protective packaging, handling it by the
  • Acer Altos R5250 | User Manual - Page 72
    To install the SAS RAID daughter board: Altos R5250 system supports SAS RAID through installation of a SAS RAID daughter board. With the addition of a RAID activation key to the SAS RAID daughter board is enabled. 1 Perform the pre-installation instructions described on page 28. 2 Locate the SAS
  • Acer Altos R5250 | User Manual - Page 73
    55 Installing an BMC module The optional BMC module allows system administrators to manage the Altos R5250 system remotely over a network. To install a BMC module: 1 Perform the pre-installation instructions described on page 28. 2 Remove the SAS daughter board. (1) Detach any cables attached to the
  • Acer Altos R5250 | User Manual - Page 74
    at both ends to snap the snap the standoff into the matching hole on the module (B). B A 6 Reinstall the SAS daughter board. 7 Observe the post-installation instructions described on page 28.
  • Acer Altos R5250 | User Manual - Page 75
    4 System BIOS
  • Acer Altos R5250 | User Manual - Page 76
    This chapter gives information about the system BIOS and discusses how to configure the system by changing the settings of the BIOS parameters.
  • Acer Altos R5250 | User Manual - Page 77
    setup loads the configuration values in a battery-backed nonvolatile memory called CMOS RAM. This memory area is not part of the system RAM which to as "Setup" or "Setup utility" in this guide. The screenshots used in this guide display default system values. These values may not be the same
  • Acer Altos R5250 | User Manual - Page 78
    menu bar. BIOS setup primary menus The tabs on the Setup menu bar correspond to the six primary BIOS Setup menus, namely: • Main • Advanced • Security • Server • Boot • Exit In the descriptive table following each of the menu screenshots, settings in boldface are the default and suggested settings.
  • Acer Altos R5250 | User Manual - Page 79
    61 BIOS setup navigation keys Use the following keys to move around the Setup utility. • Left and Right arrow keys - Move between selections on the menu bar. • Up and Down arrow keys - Move the cursor to the field you want. • PgUp and PgDn keys - Move the cursor to the previous and next page of a
  • Acer Altos R5250 | User Manual - Page 80
    62 Main menu 4 System BIOS Parameter System Time System Date BIOS Version BIOS Date Processor CPU Type CPU Speed CPU Count Total Memory Size Description Set the system time following the hour-minute-second format. Set the date following the weekday-month-day-year format. Version number of
  • Acer Altos R5250 | User Manual - Page 81
    63 Advanced menu The Advanced menu display submenu options for configuring the function of various hardware components. Select a submenu item, then press Enter to access the related submenu screen.
  • Acer Altos R5250 | User Manual - Page 82
    Clock speeds are expressed in megahertz (MHz), with 1 MHz being equal to 1 million cycles per second. The faster the clock, the more instructions the CPU can execute per second. CPU1/2 ID Processor ID number CPU1/2 L2 Cache Processor second-level cache size detected during POST Size Note: This
  • Acer Altos R5250 | User Manual - Page 83
    65 Parameter Description Option Enhanced Virus Protection Select whether to enable the Enhanced Virus Protection function. Enhanced Virus Protection allows the processor to disable code execution when a worm attempts to insert a code in the buffer preventing damage and worm propagation.
  • Acer Altos R5250 | User Manual - Page 84
    Configuration 4 System BIOS Parameter Description Option System Memory Total size of system memory detected during POST Extended Memory Total size of extended memory detected during POST Clear Disabled DIMMs Press Enter to clear disabled DIMMs. DIMM Information Displays information about
  • Acer Altos R5250 | User Manual - Page 85
    67 Advanced Chipset Control Parameter Wake on Keyboard/ Mouse Wake On Ring Wake On RTC Alarm Description Select whether to wake up the system using keyboard or mouse. Select whether to wake up the system when an incoming call is detected on the modem. Select whether to wake up the system when an
  • Acer Altos R5250 | User Manual - Page 86
    68 PCI Configuration 4 System BIOS Parameter PCI Slot 1 Option ROM Onboard LAN1/2 Control LAN 1/2 Option ROM Scan Onboard VGA Control Description When enabled, this setting will initialize the device expansion ROM for the related PCI slot. Select whether to enable the onboard network 1/2
  • Acer Altos R5250 | User Manual - Page 87
    you to configure the serial port settings. When set to Auto allows the server's BIOS or OS to select a configuration. When set to Disabled, displays or disables support for legacy Legacy Support USB devices. Enabled Disabled Serial 0,1,2 controller Select whether to enable support for SATA
  • Acer Altos R5250 | User Manual - Page 88
    70 4 System BIOS IDE Configuration The IDE Configuration submenu lets you define the parameter settings related to the system hard drive(s).
  • Acer Altos R5250 | User Manual - Page 89
    -Sector Set the multi-sector transfer mode. Transfers 16 Sectors Disabled 2 Sectors 4 Sectors 8 Sectors LBA Mode Control Selects the hard disk drive translation method. For drivers with more than 504 MB, LBA mode is necessary. Enabled Disabled
  • Acer Altos R5250 | User Manual - Page 90
    72 4 System BIOS Parameter 32-bit I/O Transfer Mode Description Option Enables or disables the 32-bit data transfer function Enabled Disabled Select a transfer mode to enhance hard disk performance. Fast PIO 4 Standard Fast PIO 1 Fast PIO 2 Fast PIO 3 FPIO 3/DMA 1 FPIO 4/DMA 2
  • Acer Altos R5250 | User Manual - Page 91
    73 Boot Configuration Parameter Description Option Boot-time Diagnostic Screen Choose whether to display the boot-time diagnostic screen during POST. Enabled Disabled Multiprocessor Select the multiprocessor (MP) specification 1.4 Specification revision level. 1.1 Note: Some operating
  • Acer Altos R5250 | User Manual - Page 92
    74 4 System BIOS Parameter NumLock Description Select the NumLock behavior during boot-up. Security Mode for PWR/RST button Enables or disables the security mode for the power button or the reset button. Option Auto On Off Enabled Disabled
  • Acer Altos R5250 | User Manual - Page 93
    Date, and Set User Password fields. • Power-on password When the Password on Boot field is enabled, a password will be required to boot up the server. To enable or disable this field, a supervisor password must first be set.
  • Acer Altos R5250 | User Manual - Page 94
    76 4 System BIOS Parameter Description Option Supervisor Password Is This parameter indicates whether a supervisor password has been assigned. Clear Enabled User Password Is This parameter indicates whether a user password has been assigned. Clear Enabled Set Supervisor Password Press
  • Acer Altos R5250 | User Manual - Page 95
    77 Changing a system password 1 Use the up/down keys to select a password parameter (Set Supervisor Password or Set User Password), then press Enter. 2 Type the original password then press Enter. 3 Type a new password then press Enter. 4 Retype the password to verify the first entry then press
  • Acer Altos R5250 | User Manual - Page 96
    78 4 System BIOS Server menu The Server menu displays submenu options for viewing basic system ID information and viewing console redirection-related and event logrelated settings. Select a submenu item, then press Enter to access the related submenu screen.
  • Acer Altos R5250 | User Manual - Page 97
    79 System Management The System Management submenu is a simple display page for basic system ID information, as well as BIOS and BMC firmware versions. Items on this window are non-configurable. Parameter Description Option Clear Case Press Enter then select whether to enable or disable the
  • Acer Altos R5250 | User Manual - Page 98
    80 Console Redirection 4 System BIOS Parameter Description COM Port Address Select whether to enable console redirection. Console redirection enables users to manage the system from a remote location. Baud Rate Select the baud rate for console redirection. Console Type Select a terminal type
  • Acer Altos R5250 | User Manual - Page 99
    81 Parameter Description Option Flow Control Assign control for the console redirection flow. None XON/OFF CTS/RTS Continue Select whether to enable console On C.R. After redirection after POST. Off POST
  • Acer Altos R5250 | User Manual - Page 100
    82 Event Log Configuration 4 System BIOS Parameter Clear All Event Logs Log POST Sys. Event Description Option Press Enter then select whether to clear all entries in the system event log. Select whether to enable the BIOS event log to be integrated in the system event log. Enabled Disabled
  • Acer Altos R5250 | User Manual - Page 101
    83 Boot menu The Boot menu allows you to set the drive priority during system boot-up. BIOS setup will display an error message if the drive(s) specified is not bootable. By default, the server searches for boot devices in the following order: 1 Optical disc drive 2 Hard drive
  • Acer Altos R5250 | User Manual - Page 102
    the default settings for all BIOS setup parameters. Setup Defaults are quite demanding in terms of resources consumption. If you are using low-speed memory chips or other kinds of low-performance components and you choose to load these settings, the system might not function properly. Discards all
  • Acer Altos R5250 | User Manual - Page 103
    5 System troubleshooting
  • Acer Altos R5250 | User Manual - Page 104
    This chapter provides possible solutions for specific problems. If you cannot correct the problem, contact your local Acer representative or authorized dealer for assistance.
  • Acer Altos R5250 | User Manual - Page 105
    the system Before going through in-depth troubleshooting, attempt first to reset the system using one of the methods below. Perform Soft boot reset Cold boot reset Purpose To clear the system memory and reload the operating system. To clear the system memory, restart POST, and reload the operating
  • Acer Altos R5250 | User Manual - Page 106
    troubleshooting Initial system startup problems Problems that occur at initial system startup are usually caused by an incorrect installation or configuration. Hardware failure is a less possible cause. If the problem you are experiencing is with a specific application, see the "There is problem
  • Acer Altos R5250 | User Manual - Page 107
    89 Initial troubleshooting checklist Use the checklist below to eliminate the possible cause for the problem you're encountering. • AC power is the system power button to turn the server on (power on indicator should be lit green)? • Are all device drivers properly installed? • Is hard disk drive
  • Acer Altos R5250 | User Manual - Page 108
    90 5 System troubleshooting Hardware diagnostic testing This section provides a detailed approach to identifying a hardware problem and its cause. Checking the boot-up status Caution: Before disconnecting any peripheral cables from the server, turn off the system and any peripheral devices.
  • Acer Altos R5250 | User Manual - Page 109
    and any other 5.25-inch device you may have installed. If any of these indicators fail to light up, refer to related problems listed in the "Specific problems and corrective actions" section. Confirming loading of the operating system Once the system boots up, the operating system prompt appears on
  • Acer Altos R5250 | User Manual - Page 110
    System troubleshooting Specific problems and corrective actions Listed below are specific problems that may arise during the use of your server and if one of them is causing the problem. • Make sure that you have properly installed system compliant memory modules, and that there populated according
  • Acer Altos R5250 | User Manual - Page 111
    guidelines. • Make sure the memory modules are properly installed on their mainboard slots. Network connection indicators do not light. Do the following: • Check the cabling and network equipment to make sure that they are in proper condition. • Reinstall the network drivers. • Try another port or
  • Acer Altos R5250 | User Manual - Page 112
    documentation for instructions on setting up and using the software. • Try a different version of the software to see if the problem is with if one of them is causing the problem. • Make sure that you have properly installed system compliant memory modules, and that there populated according
  • Acer Altos R5250 | User Manual - Page 113
    does not emit any beep code and characters still does not appear, the display monitor or the video controller may be defective. Contact your local Acer representative or authorized dealer for technical assistance.
  • Acer Altos R5250 | User Manual - Page 114
    96 5 System troubleshooting
  • Acer Altos R5250 | User Manual - Page 115
    Appendix A: Server management tools
  • Acer Altos R5250 | User Manual - Page 116
    This appendix gives an overview of the different server management tools supported by your server.
  • Acer Altos R5250 | User Manual - Page 117
    management overview The server management tools supported by the Altos R5250 system is listed in the table below. Tool Function Phoenix BIOS Setup Utility Use this tool to configure the different hardware components and system functions (memory, processor, and security settings). Go to the
  • Acer Altos R5250 | User Manual - Page 118
    100 Appendix A: Server management tools RAID configuration utilities RAID option for the Altos R5250 system is provided through either the onboard SATA controller or through an external daughter board option (SAS daughter board or SAS RAID daughter board with
  • Acer Altos R5250 | User Manual - Page 119
    the MediaShield ROM BIOS 6.77 will not appear during POST. 1 Turn on the server and the monitor. 2 During POST, press F10 on the MediaShield ROM BIOS 6.77 . Refer to the user documentation that came with your OS for related instructions. To assign a hot spare disk: You can skip this procedure. If
  • Acer Altos R5250 | User Manual - Page 120
    SAS daughter board is installed. To initialize the SAS Daughter Board Configuration Utility: 1 Turn on the server and the monitor. If the server is already turned on, close all open applications, then restart the server. 2 During POST, press Ctrl-C on the SAS BIOS prompt. To load the factory default
  • Acer Altos R5250 | User Manual - Page 121
    then exit this menu. Proceed to the installation of the operating system. Refer to the user documentation that came with your OS for related instructions. To initialize a RAID 1 volume You can skip this procedure if you selected to create a new IM array (or pressed D) while performing the creating
  • Acer Altos R5250 | User Manual - Page 122
    ) is installed. To initialize the LSI MegaRAID SAS RAID Configuration Utility: 1 Turn on the server and the monitor. If the server is already turned on, close all open applications, then restart the server. 2 During POST, press Ctrl-M on the RAID BIOS prompt. After POST completion, the Adapter
  • Acer Altos R5250 | User Manual - Page 123
    reboot the system. Proceed to the installation of the operating system. Refer to the user documentation that came with your OS for related instructions. To assign a hot spare disk: 1 On the Management menu, select Objects. 2 Select Physical Drive. All drives will be listed. 3 Select the drive marked
  • Acer Altos R5250 | User Manual - Page 124
    106 Appendix A: Server management tools
  • Acer Altos R5250 | User Manual - Page 125
    Appendix B: Rack mount configuration
  • Acer Altos R5250 | User Manual - Page 126
    This appendix shows you how to set up the Altos R5250 server in a rack mount configuration.
  • Acer Altos R5250 | User Manual - Page 127
    109 Rack installation information The Altos R5250 server system can also be mounted in a rack-model position. A rack mount kit is available for customers who want to convert system to rack-model design. To purchase a rack mount kit, contact your local Acer representative or order directly from http
  • Acer Altos R5250 | User Manual - Page 128
    110 Appendix B: Rack mount configuration • Elevated operating ambient temperature The maximum operating temperature of the system is 35 °C (95°F). Careful consideration should be given to installing the system in an environment compatible with the 35 °C (95°F) maximum ambient temperature. •
  • Acer Altos R5250 | User Manual - Page 129
    111 System rack installation The Acer Altos R5250 server should be mounted into a rack. A tool-less rack rail and CMA (cable management arm) kit is available for installing system to a rack cabinet. The figure below shows the server in a rack-mount position.
  • Acer Altos R5250 | User Manual - Page 130
    mounting holes arranged in a manner shown in the figure below: The system occupies 1U in the rack. Count the U positions and hole numbers from the bottom up the center of the next pair is equivalent to 1U. Note: The unit of measurement used in this guide is "U" (1U = 1.75 inches or 44.45 mm). The
  • Acer Altos R5250 | User Manual - Page 131
    113 Installing the system into the rack Caution! To minimize the chances of injuries, make sure that two or more people help in installing the server. To install the system into a four-post rack 1 Remove the inner rails from the mounting rails. (1) Extend the inner rail from the mounting rail until
  • Acer Altos R5250 | User Manual - Page 132
    when pressing the inner rail release latches and sliding the component into the rack. 2 Attach the inner rails to both sides of the server. Align the screw holes of the inner rail to the server screws (A), then slide rails to the left until the rails lock into place with an audible click (B).
  • Acer Altos R5250 | User Manual - Page 133
    115 3 Install the mounting rails to the rack posts. (1) Determine the vertical position in the rack. Refer to "Vertical mounting hole pattern" on page 112 for more information. (2) Align and insert the mounting rails into the rack posts' mounting holes (A). (3) Make certain the proper mounting holes
  • Acer Altos R5250 | User Manual - Page 134
    116 Appendix B: Rack mount configuration (6) Fully extend the mounting rails on the rack.
  • Acer Altos R5250 | User Manual - Page 135
    should be taken when pressing the inner rail release latches and sliding the component into the rack. (1) Carefully align the inner rails attached to the server with the fully extended mounting rails on the rack. (2) Press the release latch on both sides of the
  • Acer Altos R5250 | User Manual - Page 136
    118 Appendix B: Rack mount configuration 5 Attach the CMA (cable management arm) to the rear of the server. The CMA allows you to tie-wrap all cables to and from the system. As you slide the system in and out of the rack,
  • Acer Altos R5250 | User Manual - Page 137
    119 (6) Connect the power, peripheral and networking cables into their appropriate ports. Refer to "Connecting peripherals" on page 20 for detailed instructions. (7) Route all cables through the cable clips.
  • Acer Altos R5250 | User Manual - Page 138
    120 Appendix B: Rack mount configuration
  • Acer Altos R5250 | User Manual - Page 139
    inch device bays supported devices 4 A 70 Main menu 62 Memory Configuration 66 navigation keys 61 PCI Configuration 68 Security menu 75 Server menu 78 System activity indicator, status 15 BIOS settings 70 RAID configuration 100 troubleshooting 92 hardware monitor 12 HDD installing 36 removing 35 heat
  • Acer Altos R5250 | User Manual - Page 140
    LAN port 16 M media storage specification 4 memory BIOS settings 66 reconfiguring 50 troubleshooting 93 O Onboard SATA RAID Configuration Utility Daughter Board Configuration Utility 104 serial port BIOS setting 69 server management tools 99 setting up the system 19 preinstallation requirements
  • Acer Altos R5250 | User Manual - Page 141
    28 preinstallation instructions 28 T thermal grease 45 top cover installing 32 removing 31 123 troubleshooting display problems 94 DVD-ROM drive problems 92 FAQ 92 hardware diagnostics 90 HDD problem 92 initial checklist 89 initial startup problems 88 memory problem 93 network problems 93 power
  • Acer Altos R5250 | User Manual - Page 142
    124
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Acer Altos R5250 Series
User’s Guide