Acer Altos R700 Altos R700 Chassis Subassembly
Acer Altos R700 Manual
 |
View all Acer Altos R700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Acer Altos R700 manual content summary:
- Acer Altos R700 | Altos R700 Chassis Subassembly - Page 1
Altos R700 Chassis Subassembly Product guide - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 2
© 2002 Acer Incorporated All Rights Reserved. Altos R700 Chassis Subassembly Product guide Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual or - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 3
installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 4
not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this server. Use conditions This part complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 5
safety instructions Read these instructions carefully. Save these instructions for future reference. 1 Follow all warnings and instructions marked on all servicing to qualified service personnel. 11 Unplug this product from the wall outlet and refer servicing to qualified service personnel under - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 6
when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper If the product exhibits a distinct change in performance, indicating a need for service. 12 Replace the battery with the same type as the product's battery we - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 7
Before You Begin 17 Supplies Needed 17 Installation/Assembly Safety Instructions 18 Use Only for Intended Applications 18 Checking the Power a PCI Card on a Riser Card 35 Installing the Riser Cards on the Server Board 36 Installing a Hard Drive 37 Installing a DVD drive/FDD or CD- - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 8
57 Installing a Redundant Fan 59 Replacing the Fan Module 61 Replacing a Backplane Board 62 Replacing a Front Panel Board 63 Replacing a Server Board 64 Appendix A: Equipment Log and Worksheets 67 Equipment Log 68 Current Usage 70 Calculating Power Usage 70 Worksheet, Calculating - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 9
1 Chassis Description - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 10
2 What Your Kit Includes 1 Chassis Description Your Altos R700 server chassis kit is designed to support the Altos R700 Server Board. The fan module and riser cards are installed for shipment, but you must remove and reinstall them when you install the server board. Your kit includes the following - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 11
3 Items You Must Purchase Separately The following components must be purchased separately: • Front bezel (optional) • Altos R700 Server Board • Minimum of one Intel® Xeon™ processor • Registered ECC DDR RAM memory DIMMs • SCSI hard disk drives (HDD) • Slimline DVD/CD-ROM drive/floppy disk - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 12
1 Chassis Description Label A B C D E F G H Description Power supply PCI card bracket (full-lenght) Riser card assembly (full-lenght) PCI card bracket (low-profile) Server board (accessory to system) PCI add-in card (accessory to system) Riser card assembly (low-profile) Processor air duct - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 13
5 Label I J K L M N O Description Front panel board Intrusion switch Control panel Flex bay (optional DVD/CD-ROM drive/FDD module available) Tape drive bay (tape drive available from others) Hard drive bay (one of six, accessory to system) Backplane board Chassis Front Panel and Peripheral Bays - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 14
6 1 Chassis Description Label D E F Description Flex bay (optional DVD/CD-ROM drive/FDD module shown installed) Front panel indicator lights Tape drive bay (tape drive not included) Chassis Back I/O Ports and Features Label A B C D E F G H I Description PCI card bracket (low profile) RJ45 NIC - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 15
7 Label J K L M N O Description RJ45 serial port PS/2 mouse/keyboard connector RJ45 NIC 1 connector SCSI channel A connector (If available) Video connector USB connector 1 Note: 480 Watt redundant power supply shown. Your power supply may be different. Front Panel Controls and Indicators Shown - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 16
8 Label C D E F G H I J K Description Power/sleep LED Fixed disk drive status LED System status LED ID LED ID button Reset button USB Connector NMI button Video Connector 1 Chassis Description - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 17
compliant operating systems. Reboots and initializes the system. Pressing the recessed button with a paper clip or pin issues a non-maskable interrupt and puts the server in a halt state for diagnostic purposes. Toggles on/off the front panel ID LED and the baseboard ID LED. The baseboard ID LED is - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 18
Management Controller (BMC), or the system board must be used with the 2U Altos R700 hot swappable backplane. 3. Also off when the system is powered off or in the chipset. If the system is powered down without going through BIOS, the LED state in effect at the time of power off will be restored when - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 19
11 Peripherals The chassis provides external bays for peripherals that can be purchased separately and added to the system. The following describes the available options. Label A B C D E Description Hard drive bays (6) Flex bay (1) DVD/CD-ROM drive/floppy disk drive module Tape drive Hard disk - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 20
and is rated as follows: • 100-120 V~ at 50/60 Hertz (Hz); 5.2 A maximum • 200-240 V~ at 50/60 Hz; 2.6 A maximum The power subsystem supports implementation of remote management features including remote enable that permits power to be activated from a variety of sources. System Cooling The chassis - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 21
the cover is opened, the switch, located on the front panel board, transmits a signal to the Baseboard Management Controller (BMC) on the server board, where server management software processes the signal. Locking and Unlocking the Front Bezel To unlock the bezel, insert the key in the lock and - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 22
14 1 Chassis Description - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 23
2 Assembling the System - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 24
the System Before the Altos R700 can be installed for use, you must assemble the hardware components that make up your particular system. Additionally, you will want to add any peripherals and add-in cards purchased for the system. The following procedures help guide you through this assembly - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 25
make sure you have the following supplies available: • Anti-static wrist strap (recommended) • Altos R700 accessory kit (included) • Altos R700 Server Board • Processors and memory you purchased separately to add to the server board • Optional peripherals and add-in cards you want to include in the - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 26
Instructions Before you start the assembly process, you will need to make sure you follow certain basic safety precautions. Caution: Only technically qualified persons shall perform integration/ servicing observe all warnings and cautions in the Installation Guide. To avoid injury, be careful of: • - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 27
power cord must be rated for the available AC voltage and have a current rating that is at least 125% of the current rating of the server. • The plug on the power cord that plugs into the wall outlet must be a grounding-type male plug designed for use in your region. It - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 28
power. To disconnect power from the server, you must unplug all AC power server before opening it. Otherwise, personal injury or equipment damage can result. Warning: Do not open the power supply. Hazardous voltage, current and energy levels are present inside the power supply. Refer servicing - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 29
21 Installing System Components Remove the Cover 1 While pressing the blue latch button (A) with your left thumb, slide the top cover back using the heel of your right hand on the blue pad. Note: A non-skid surface or a stop behind the chassis may be needed if attempting to remove the top cover on a - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 30
22 Remove the Processor Air Duct Lift the processor air duct out of the chassis. 2 Assembling the System Remove the Riser Cards 1 Insert your finger in the plastic loop. On riser card (A), also grasp the opposite end at (C). 2 Pull straight up and remove the riser card from the chassis. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 31
23 3 Discard the protective blocks. Remove the Fan module 1 Lift the processor duct out of the chassis. 2 If it is installed, remove the 100-pin flex circuit. 3 At the end of the fan module closest to the chassis centerline, push on the tab to release it from the chassis (A). 4 While pushing on the - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 32
24 6 Lift the fan module out of the chassis. 2 Assembling the System Install the Server Board Caution: Do not install any server board support bumpers in the Altos R700 chassis. System components must be installed in the order presented below. If installed in a different order, component damage - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 33
25 5 Attach the board to the chassis using the three screws shipped in the chassis accessory kit. 6 Install processors and memory, following the directions on the Altos R700 Server Board Product Guide. 7 If you only install one processor, you must install the processor air dam. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 34
26 2 Assembling the System a Attach processor retention piece (B) to the server board (C) using the provided screws (A). b Put the air dam(D) into place. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 35
27 Routing Cables Label 1 2 3 4 Description Power Supply SCSI Hard Disk Drives DVD/CD-ROM/FDD module Tape Drive (optional) - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 36
Assembling the System Label 5 6 7 8 A B C D E F G H I J Description Front Panel Board Fan Module SCSI Backplane (shown horizontal for clarity) Server Board To backplane power connector from power supply To server board primary power connector from power supply Floppy/FP/IDE flex circuit cable from - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 37
board power cable to the white 24-pin connector on the server board. Firmly press the two connectors together until they are fully seated. Install the Fan module Caution: When installing the fan module, avoid pinching cables - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 38
down on the fan module, slide it in the direction of arrow (2) until the latch snaps into place. 5 Connect the fan power cables to the server board. Connect Flex Circuit Cable 1 Remove the flex circuit cable from the cable bag in the accessory kit. Connect the end marked "P1 - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 39
31 the backplane board and connect the other cable end to the matching connector on the backplane. Caution: Ensure that each cable connector is properly seated in the board connector. The connector should be parallel to its board connector and not cocked to one side. If in doubt, remove, reinsert, - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 40
place over the backplane and flex circuit cable. Connect Auxiliary Power Cables 1 Connect the auxiliary power cable to the 8-pin auxiliary power connector on the server board (A). 2 Connect the signal cable to the 5-pin signal connector on the - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 41
USB cable to the USB connector on the front panel. Route the cable along the top of the fan module and connect it to the server board. Make sure the cable does not lay on top of the corner of the backplane or it will get damaged when you install the - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 42
from the power supply should route through the notch in the bottom of the baffle. 4 Connect the SCSI cable to the SCSI connector on the server board. Route the cable between the memory connectors and the full height PCI riser, through the clips on the side of the processor duct, through - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 43
nearest the chassis sidewall (see "Installing the Riser Cards on the Server Board" on page 36, B) supports three Low Profile (LP) PCI add-in cards. The riser If your full-length card has a card guide attached to the end opposite the metal bracket, remove the guide. 2 Insert the edge connector of the - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 44
into the riser card slot until it is fully seated. 4 Close the retainer clip (E). Ensure the clip is latched. Installing the Riser Cards on the Server Board 1 Align the riser card connector with the server board slot. 2 Firmly press the riser card straight down until it is fully seated in the - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 45
37 3 Install the other riser card in the same manner. Label A B Description Full-length riser card Low-profile riser card Installing a Hard Drive The server can support up to seven hot swappable hard drives: six hard drives in the drive bays, plus one in the flex bay. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 46
Store the air baffle for future reinstallation in the event you must operate your server without a drive in one of the bays. 5 Remove the hard drive from or switches on the drive according to the drive manufacturer's instructions. 7 With the drive circuit-side-down (A), position the connector end (E) - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 47
Reinstall a carrier/air baffle in any bays where you are not installing a carrier/drive. Installing a DVD drive/FDD or CD-ROM drive/FDD Module Your server does not come with a DVD drive, CD-ROM drive or floppy disk drive. As an accessory, Intel offers slim-line DVD drive/FDD and CDROM - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 48
40 2 Assembling the System 3 Insert the module into the flex bay and slide it back until you feel the connectors touch. 4 With your thumbs positioned above the handle bar indentations (D), push the module in until it locks in place. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 49
"Chassis Back I/O Ports and Features" on page 6). Connect the other end to the COM 1 serial port header on the server board (see the documentation that shipped with your server board). Install the Cover 1 Place the cover over the chassis. 2 Slide it forwards until it latches into place. Installing - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 50
42 2 Assembling the System To release the plastic loop and free the cord, squeeze the release lever (D). Install the Bezel Place the bezel between the chassis handles and push it toward the front of the chassis until it snaps into place. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 51
3 Installing the System in a Rack - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 52
44 3 Installing the System in a Rack Your Altos R700 chassis comes equipped with a rack mount kit that support to prevent it from falling over when one or more servers are extended in front of it on slide assemblies. The equipment rack must be installed according to the manufacturer's instructions - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 53
to maintain proper cooling. It must also include ventilation sufficient to exhaust a maximum of 2110 Btu's per hour for a fully loaded Altos R700 server. It is important to note that this is the maximum, and a minimum or typical system could be much less. You may want to calculate the - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 54
46 3 Installing the System in a Rack - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 55
4 Working Inside Your Server - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 56
This chapter describes how to replace components in your server after it has been set up. All references to left, right, front and rear are based on the reader facing the front of the chassis. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 57
components inside the server. Only a technically qualified person should integrate and configure the server. Lithium Battery manufacturer. Dispose of used batteries according to the manufacturer's instructions. ADVARSEL: Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 58
50 4 Working Inside Your Server VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 59
51 Replacing Components Replacing a Hard Drive CAUTION: To allow proper airflow and cooling during operation, all drive bays must contain either a carrier/drive or a carrier with air baffle installed. 1 Before removing the cover to work inside the system, observe the safety guidelines on page 48. 2 - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 60
jumpers and/or switches on the drive according to the drive manufacturer's instructions. 8 Install the new drive in the carrier and the carrier/drive into hot swappable. Before replacing it, you must first take the server out of service, turn off all peripheral devices connected to the system, turn - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 61
53 3 Grasp the handle bar at both ends and firmly pull out to disengage the connector. (When you first pull, resistance will be high until the connector disengages.) 4 Slide the module out of the flex bay. 5 On the replacement module, rotate the handle bar down. 6 Insert the replacement module into - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 62
54 4 Working Inside Your Server Replacing a PCI Add-in Card If you will be replacing a low-profile PCI add-in card, see figure below. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 63
55 If you will be replacing a full-length PCI add-in card, see figure below. 1 Before removing the cover to work inside the system, observe the safety guidelines on page 48. 2 Insert your finger in loop A and remove the riser card assembly that contains the add-in card you desire to replace. If you - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 64
must take the server out of service before replacing the single module. 1 Squeeze the module handle to depress the latch (A) that is the right side of the handle. 2 Rotate the handle down (B) while pulling the module toward you (C). As you pull the module out, support - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 65
the fan module. 7 Disconnect and remove all data cabling necessary to gain access to the power cables. 8 Disconnect the main power connector from the server board. 9 Disconnect all other power cables from their devices. 10 At the rear of the chassis, remove the two screws (A) that secure the power - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 66
chassis standoff and slide it toward the front of the server (D). Lift the power supply out of the chassis Plug the main power connector into the server board. 16 Connect all other power cables to module and connect the fan power cables to the server board. 18 Install the full-height PCI riser card - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 67
59 21 21. Connect the power cord(s) to the power cord receptacle(s) and plug the cord(s) back into the power source. Installing a Redundant Fan 1 Before removing the cover to work inside the system, observe the safety guidelines on page 48. 2 Remove the cover from the chassis. 3 Remove the full- - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 68
60 4 Working Inside Your Server 10 Remove the fan blank from the fan module. 11 Connect the fan module toward the chassis sidewall until it has locked in place. 15 Plug the fan cables into the server board system fan connectors. 16 Make sure the USB cable is routed along the top of the fan module - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 69
the chassis floor. 11 Slide the fan module toward the chassis sidewall until it has locked in place. 12 Plug the fan cables into the server board system fan connectors. 13 Make sure the USB cable is routed along the top of the fan module. 14 Connect the flex circuit cable - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 70
62 4 Working Inside Your Server 15 Install the flex circuit cable retention clip. 16 Install the full-height PCI riser card. 17 Replace the chassis cover. Replacing a Backplane Board 1 Before - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 71
63 9 Install and tighten the thumscrew. Caution: Carefully route cables in their original paths to minimize airflow blockage and cooling problems. 10 Connect all cables to the board. 11 Install the fan module. 12 Install the full-height PCI riser card. 13 Install all hard drives - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 72
to the chassis with the thumbscrew. 8 Plug the USB and backplane cables back into the front panel board. 9 Replace the chassis cover. Replacing a Server Board 1 Before removing the cover to work inside the system, observe the safety guidelines on page 48. 2 Disconnect all cables from the rear I/O of - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 73
the rear chassis wall and that the sheet is laying flat on the chassis floor. 11 Place the new server board on the chassis standoffs, being careful to position the board I/O connectors in the rear chassis I/O openings. cables in their original paths to minimize airflow blockage and cooling problems. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 74
66 4 Working Inside Your Server 15 Cable the new server board to the other system components. 16 Install the fan module. 17 Install the PCI riser cards. 18 Replace the chassis cover. 19 Connect any cables removed from the rear I/O of the chassis. - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 75
Appendix A: Equipment Log and Worksheets - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 76
information about your system. You will need some of this information when you run the SSU. Item Manufacturer Name and Model Name Chassis Server Board Processor Speed and Cache Video Display Video Controller Keyboard Mouse 3.5-inch Drive CD-ROM Drive Hard Disk Drive 1 Hard Disk Drive - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 77
69 Item DAT TApe Drive Manufacturer Name and Model Name Serial Number Date Installed - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 78
70 Appendix A: Equipment Log and Worksheets Current Usage Calculating Power Usage The total combined power consumption for your configuration must be less than 500W, with any combination of loads not to exceed maximum current on any one channel as defined in Power Usage Worksheet 1. The combined - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 79
Power Usage Worksheet 1 Device Current (maximum) at voltage level: +5 Vsb +3.3 V +5 V +12 V -12 V Boards, processors, and memory (get totals from your board manual) SCSI backplane and 0.40 front panel 3.5-inch drive 0.30 CD-ROM drive 0.60 3.5-inch tape drive or other peripheral 1st hot - Acer Altos R700 | Altos R700 Chassis Subassembly - Page 80
72 Appendix A: Equipment Log and Worksheets Worksheet, Total Combined Power Used by the System 1 From the previous worksheet, enter the total current for each column. 2 Multiply the voltage by the total current to get the total wattage for each voltage level. 3 Add the total wattage for each
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
 |
 |
Altos R700
Chassis Subassembly
Product guide