Acer ConceptD CM100-51A User Manual
Acer ConceptD CM100-51A Manual
 |
View all Acer ConceptD CM100-51A manuals
Add to My Manuals
Save this manual to your list of manuals |
Acer ConceptD CM100-51A manual content summary:
- Acer ConceptD CM100-51A | User Manual - Page 1
ConceptD User Manual ConceptD CM100 - Acer ConceptD CM100-51A | User Manual - Page 2
Reserved. Desktop Computer Covers: Tower models This revision: Jan 2020 V1.00 Important This manual contains proprietary information that is protected by copyright laws. The information contained in this manual is subject to change without notice. Images provided herein are for reference only and - Acer ConceptD CM100-51A | User Manual - Page 3
Table of Contents 1. UPGRADING YOUR COMPUTER 5 Installation precautions 5 ESD precautions 5 Required tools 5 Pre-installation instructions 6 Post-installation instructions 6 System Upgrade 7 Re moving the left side syste m cover .... 7 Installing the left side system cover ..... 8 Hard - Acer ConceptD CM100-51A | User Manual - Page 4
4 - Upgrading your Computer Upgrading your Computer In this section, you will find: • Instructions on how to replace a hardware component - Acer ConceptD CM100-51A | User Manual - Page 5
that you read the following sections. These sections contain important ESD precautions along with pre-installation and post-installation instructions. ESD precautions Electrostatic discharge (ESD) can damage your processor, disk drives, expansion boards, and other components. Always observe the - Acer ConceptD CM100-51A | User Manual - Page 6
may cause serious damage. Do not attempt the procedures described in the following sections unless you are a qualified service technician. Post-installation instructions Observe the following after installing a computer component: 1. See to it that the components are installed according to the - Acer ConceptD CM100-51A | User Manual - Page 7
system cover 1. Before you proceed, make sure that you have turned off your computer and all peripherals connected to it. Read the Pre- installation instructions on page 6. 2. Remove the two screws that secure the system cover to the computer. 3. Slide the cover toward the back of the computer and - Acer ConceptD CM100-51A | User Manual - Page 8
8 - Upgrading your Computer Installing the left side system cover 1. Align the cover to the sides of the computer and slide the cover toward the front of the computer. 2. Secure the cover with two screws. 3. Observe the Post-installation instructions on page 6. - Acer ConceptD CM100-51A | User Manual - Page 9
Upgrading your Computer - 9 Hard drives The computer supports installation of one 3.5-inch SATA hard drives in the internal HDD cage. Removing the 3.5-inch hard drives 1. Perform Pre-installation instructions on page 6. 2. Remove the front bezel. - Acer ConceptD CM100-51A | User Manual - Page 10
10 - Upgrading your Computer 3. Disconnect the power、data cables (1) and the power button cable (2) . 1 2 4. Remove five screws for HDD cage. - Acer ConceptD CM100-51A | User Manual - Page 11
Upgrading your Computer - 11 5. Release two mounting structure form the chassis. 6. Remove the four screws that secure the hard drives to the bracket. - Acer ConceptD CM100-51A | User Manual - Page 12
12 - Upgrading your Computer Installing the 3.5-inch hard drives 1. Remove the new hard drive from their packaging. 2. Insert the new hard drive into the bracket and secure the new hard drive with four screws. 3. Installing HDD cage on chassis. - Acer ConceptD CM100-51A | User Manual - Page 13
4. Fixed five screws for HDD cage. Upgrading your Computer - 13 5. Connect the power、data cables (1) and the power button cable (2) . 1 2 - Acer ConceptD CM100-51A | User Manual - Page 14
14 - Upgrading your Computer 6. Installing the front bezel. 7. Observe the Post-installation instructions on page 6. - Acer ConceptD CM100-51A | User Manual - Page 15
Upgrading your Computer - 15 Memory The computer has four DDR4 U-DIMM slots that support up to 64 GB maximum system memory. Memory configuration guidelines DIMM2 DIMM1 To ensure data integrity, use only Acer-approved DDR4 2400 MHz or DDR4 - Acer ConceptD CM100-51A | User Manual - Page 16
16 - Upgrading your Computer Removing a memory module 1. Perform Pre-installation instructions on page 6. 2. Press outward the holding clips on both sides of the DIMM slot outward to release the memory module (1). 3. Gently pull the memory module - Acer ConceptD CM100-51A | User Manual - Page 17
notch in the module lines up with the tab in the memory slot. 1 2 5. Repeat steps 1~4 to install the other memory modules. 6. Observe the Post-installation instructions on page 6. - Acer ConceptD CM100-51A | User Manual - Page 18
installed in the PCIe x16 slots. The detail configuration will be differed by different models. Removing the Graphic board 1. Perform Pre-installation instructions on page 6. 2. Remove the screw that secure the Graphic boards to the chassis. 3. Release the latch that secures the graphic board to - Acer ConceptD CM100-51A | User Manual - Page 19
Upgrading your Computer - 19 4. Detach the Graphic board from the PCIe x16 slot. - Acer ConceptD CM100-51A | User Manual - Page 20
supply first in order to make sure the graphic board and power supply could work. 3. Secure the Graphic board with screws. 4. Observe the Post-installation instructions on page 6. - Acer ConceptD CM100-51A | User Manual - Page 21
- 21 M.2 SSD module The computer contains one M.2 SSD module installed in the M.2 PCIe slot. Removing the M.2 SSD module 1. Perform Pre-installation instructions on page 6. 2. Remove the 3.5-inch hard drives. See removing the 3.5-inch hard drives. 3. Remove the screws that secure the M.2 SSD module - Acer ConceptD CM100-51A | User Manual - Page 22
the mainboard. 3. Secure the M.2 SSD module and mainboard with screws. 4. Replace the 3.5-inch hard drives. See installing the 3.5-inch hard drives. 5. Observe the Post-installation instructions on page 6.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
 |
 |
ConceptD
User Manual
ConceptD CM100