Adaptec 1870700 Installation Guide
Adaptec 1870700 - 29160 Powerdomain Mac Sglu160 SCSI Hd68 LVD Ext Conn Manual
 |
UPC - 760884137321
View all Adaptec 1870700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Adaptec 1870700 manual content summary:
- Adaptec 1870700 | Installation Guide - Page 1
R INSTALLATION GUIDE ADAPTEC SCSI CARD 29160 ULTRA160 SCSI CONTROLLER - Adaptec 1870700 | Installation Guide - Page 2
- Adaptec 1870700 | Installation Guide - Page 3
the Adaptec SCSI Card 29160 is a 64-bit PCI card, it also works in a 32-bit PCI slot. When installed in a 32-bit PCI slot, the card automatically runs in the slower 32-bit mode. This installation guide explains how to • Install the Adaptec SCSI Card 29160 • Set up SCSI devices • Connect SCSI devices - Adaptec 1870700 | Installation Guide - Page 4
the primary LVD/SE segment from the secondary SE segment on the SCSI bus. This allows the Adaptec SCSI Card 29160 to support LVD SCSI devices at speeds up to 160 MBytes/sec on the primary LVD/SE segment while at the same time supporting Ultra (legacy) devices at speeds up to 40 MBytes/sec on the - Adaptec 1870700 | Installation Guide - Page 5
Adaptec SCSI Card 29160 INSTALLING THE ADAPTEC SCSI CARD 29160 STEP 1 Discharge any static electricity build-up before handling the SCSI card you can install the card in a 32-bit PCI slot. (The expansion slot must be compliant with PCI Rev. 2.1 or higher and must support Bus Mastering.) Save the - Adaptec 1870700 | Installation Guide - Page 6
Guide Computers may have vertical or horizontal expansion slots. Refer to your computer manual to locate the PCI slots. If your computer is a tower model, lay it on its side to make it easier to install the Adaptec SCSI Card 29160. WARNING Be careful when inserting the Adaptec SCSI Card 29160 - Adaptec 1870700 | Installation Guide - Page 7
for specific instructions. Below are some guidelines for checking SCSI IDs, setting termination, and mounting devices in your computer. Refer to the Adaptec SCSI Card 29160 User's Reference for more information on these topics. Check the SCSI IDs The Adaptec SCSI Card 29160 and each device - Adaptec 1870700 | Installation Guide - Page 8
Installation Guide usually have a terminator built into the end of cable. With this type SCSI device. Mount the Devices If you have internal SCSI devices, mount each device in an available drive bay inside your computer, as shown below. Refer to your computer and device documentation for instructions - Adaptec 1870700 | Installation Guide - Page 9
to the Adaptec SCSI Card 29160 User's Reference. NOTE SCSI devices can be connected to all four SCSI connectors on the Adaptec SCSI Card 29160 at the same time. Connecting Internal LVD SCSI Devices Connect internal LVD SCSI devices to the internal LVD/SE connector on the Adaptec SCSI Card 29160. To - Adaptec 1870700 | Installation Guide - Page 10
Installation Guide STEP 2 Plug the nonterminated end of the cable to the internal LVD/SE connector. 68-pin Internal LVD SCSI Cable 68-pin Internal LVD/SE Connector STEP 3 Plug the internal LVD SCSI devices to the other cable connectors, starting with the connector at the terminated end of the - Adaptec 1870700 | Installation Guide - Page 11
Adaptec SCSI Card 29160 STEP 4 Connect a power cable from your computer's internal power supply to each internal SCSI device. Power Cable (From the Power Supply Inside the Computer) Power Input Connector on the Back of the Device STEP 1 Connecting Internal Ultra/Wide SCSI Devices Connect - Adaptec 1870700 | Installation Guide - Page 12
Installation Guide STEP 2 Plug one end of the cable to the Wide SCSI connector on the Adaptec SCSI Card 29160. 68-pin Internal Wide SCSI Cable 68-pin Wide SCSI Connector STEP 3 Plug the other end of the cable to a terminated Ultra/Fast Wide SCSI device. Terminated SCSI Device STEP 4 If you - Adaptec 1870700 | Installation Guide - Page 13
Adaptec SCSI Card 29160 STEP 5 Connect a power cable from your computer's internal power supply to each internal device. Power Cable (From the Power Supply Inside the Computer) Power Input - Adaptec 1870700 | Installation Guide - Page 14
Installation Guide J STEP 2 Plug one end of the cable to the 50-pin internal SE Narrow SCSI connector on the Adaptec SCSI Card 29160. 50-pin Internal Narrow SCSI Connector STEP 3 50-pin Internal Ultra Narrow SCSI Cable Plug the other end of the cable to a terminated Ultra/Fast Narrow SCSI - Adaptec 1870700 | Installation Guide - Page 15
. (See Bus Segments on the Adaptec SCSI Card 29160 on page 4.) STEP 1 Follow these steps to connect the external devices: Connect one end of the external LVD SCSI cable to the external LVD/SE connector on the Adaptec SCSI Card 29160. 68-pin External LVD/SE SCSI Connector 68-pin External LVD - Adaptec 1870700 | Installation Guide - Page 16
Installation Guide STEP 2 Connect the other end of the external SCSI cable to a SCSI connector on the back of an external SCSI device. SCSI Terminator 4 4 If you are installing only one external device, terminate the device and skip to Step 4. NOTE An LVD terminator must be used for LVD SCSI - Adaptec 1870700 | Installation Guide - Page 17
systems. Refer to the Ultra160 Family Manager Set User's Guide and Adaptec SCSI Card 29160 User's Reference for instructions on either installing driver software when installing your operating system, or installing driver software when the operating system is already installed. NOTE Operating - Adaptec 1870700 | Installation Guide - Page 18
Guide TROUBLESHOOTING If you have any problems while installing the Adaptec SCSI Card 29160, check the following items first: • Are all SCSI devices powered on? • Are all SCSI cables and power cables properly connected? • Does each device on the SCSI bus have a unique SCSI ID? • Does the total SCSI - Adaptec 1870700 | Installation Guide - Page 19
- Adaptec 1870700 | Installation Guide - Page 20
information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, Adaptec, Inc. assumes no liability resulting from errors or omissions in this document, or from the use of the information contained herein - Adaptec 1870700 | Installation Guide - Page 21
energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is , including interference that may cause undesired operation. Adaptec, Inc. Adaptec SCSI Card 29160 Tested to Comply With FCC Standards FOR HOME - Adaptec 1870700 | Installation Guide - Page 22
- Adaptec 1870700 | Installation Guide - Page 23
- Adaptec 1870700 | Installation Guide - Page 24
R We move the information that moves your world.™ © 2000 Adaptec, Inc. All rights reserved. Printed in Singapore Stock No.: 512520-03, Rev. A RAC 1/00 (SRC: 512520-00, Ver. AA)
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
 |
 |
R
I
NSTALLATION
G
UIDE
A
DAPTEC
SCSI C
ARD
29160
U
LTRA
160 SCSI C
ONTROLLER