Adaptec 29320-R Installation Guide
Adaptec 29320-R - SCSI Card RAID Controller Manual
 |
UPC - 760884140208
View all Adaptec 29320-R manuals
Add to My Manuals
Save this manual to your list of manuals |
Adaptec 29320-R manual content summary:
- Adaptec 29320-R | Installation Guide - Page 1
INSTALLATION GUIDE ADAPTEC SCSI CARD 29320 - Adaptec 29320-R | Installation Guide - Page 2
computer with 64- or 32-bit PCI/PCI-X expansion slots. The Adaptec SCSI Card 29320 guide explains how to: •Install the Adaptec SCSI Card 29320 •Set up SCSI devices •Connect SCSI devices NOTE If you connect Wide Ultra/Ultra SCSI devices to the same SCSI connectors as Ultra320/160 and Ultra2 SCSI - Adaptec 29320-R | Installation Guide - Page 3
3 Locate an unused 64-bit PCI/PCI-X expansion slot and remove the expansion slot cover. If the computer does not have a 64-bit slot, you can install the card in a 32-bit PCI slot. The Adaptec SCSI Card 29320 supports both 5V and 3.3V 64-bit slots. (The expansion slot must be compliant with PCI Rev - Adaptec 29320-R | Installation Guide - Page 4
or horizontal expansion slots. Refer to your computer manual to locate the PCI/PCI-X slots. If your computer is a tower model, lay it on its side to allow for easier installation of the Adaptec SCSI Card 29320. WARNING Be careful when inserting the Adaptec SCSI Card 29320 in a PCI slot. Some 32-bit - Adaptec 29320-R | Installation Guide - Page 5
You can connect a total of up to 15 LVD and/or 15 SE SCSI devices to the Adaptec SCSI Card 29320. Before connecting devices, be sure to review Setting Up SCSI Devices on page 3. Connecting Internal Ultra320/160 and Ultra2 Devices A special 68-pin internal LVD cable is needed to connect internal - Adaptec 29320-R | Installation Guide - Page 6
have a terminator built into the end of the cable. The Adaptec SCSI Card 29320 has one internal 68-pin LVD/SE connector and two internal SE connectors to which you can connect internal SCSI devices, as shown in the figure on page 1. NOTE Adaptec recommends that you keep your Ultra320/160 and Ultra2 - Adaptec 29320-R | Installation Guide - Page 7
the terminator at the end of the LVD SCSI cable. STEP 4 STEP 1 Connect a power cable from your computer's internal power supply to each internal SCSI device. Connecting Wide SCSI Devices Connect internal Wide SCSI devices to the 68-pin internal SE Wide SCSI connector. To do this, use a 68-pin Wide - Adaptec 29320-R | Installation Guide - Page 8
STEP 2 Plug one end of the cable to the Wide SCSI connector on the Adaptec SCSI Card 29320. STEP 3 STEP 4 STEP 5 STEP 1 STEP 2 Plug the other end of the cable to a terminated Ultra/Fast Wide SCSI device. If you have other Ultra/Fast Wide SCSI devices, attach them to the connectors between the two - Adaptec 29320-R | Installation Guide - Page 9
the Ultra320/160 and Ultra2 SCSI devices on the same SCSI channel of the Adaptec SCSI Card 29320. STEP 1 Follow these steps to connect your external SCSI devices: Connect one end of an external SCSI cable to the external Ultra320/160 connector on the Adaptec SCSI Card 29320. 68-pin external LVD - Adaptec 29320-R | Installation Guide - Page 10
on the back of an external device. If you are installing only one external device, terminate the device and skip to Step 4. SCSI terminator 4 4 STEP 3 Connect the other external SCSI devices by linking each device to the previous one, as shown below. Terminate only the device at the end of the - Adaptec 29320-R | Installation Guide - Page 11
(sometimes called an Ultra terminator) the SCSI devices will not operate properly. TROUBLESHOOTING If you have any problems while installing the Adaptec SCSI Card 29320, check the following items first: •Are all SCSI devices powered on? •Are all SCSI cables and power cables properly connected - Adaptec 29320-R | Installation Guide - Page 12
the computer manufacturer. No further action is necessary to install the driver. Embedded Adaptec Drivers Some operating systems have embedded driver support for the Adaptec SCSI Card 29320. To determine if the card is supported by the operating system you are using, read the operating system manual - Adaptec 29320-R | Installation Guide - Page 13
been made in the preparation of this document to assure its accuracy, Adaptec, Inc. assumes no liability resulting from errors or omissions in this and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there - Adaptec 29320-R | Installation Guide - Page 14
interference that may cause undesired operation. Adaptec, Inc. Adaptec SCSI Card 29320 Tested to Comply With FCC Standards causes radio frequency interference problem if used too near to a television or radio. Please handle it correctly per this documentation. R © 2002 Adaptec, Inc. All rights
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
I
NSTALLATION
G
UIDE
A
DAPTEC
SCSI C
ARD
29320