Amana UMV1160CW Installation Instructions

Amana UMV1160CW Manual

Get Amana UMV1160CW PDF manuals and user guides View all Amana UMV1160CW manuals
Add to My Manuals
Save this manual to your list of manuals

Amana UMV1160CW manual content summary:

  • Amana UMV1160CW | Installation Instructions - Page 1
    Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting Plate 4 Rotate Blower Motor 4 Locate Wall Stud(s 6 Mark
  • Amana UMV1160CW | Installation Instructions - Page 2
    and parts before starting installation. Read and follow the instructions provided ■■ Mounting plate (attached to back of microwave oven) E. 1/4" x 2" lag screws (2) ■■ Cardboard template (part of drywall or plaster/lath within cabinet opening. ■■ Support for weight of 150 lbs (68 kg) which
  • Amana UMV1160CW | Installation Instructions - Page 3
    Failure to follow these instructions can result in death, mounting kit replacing the I bar mounting plate fr om the wall. The bump out mounting kit (part # W11185746) is not provided but can be purchased from Whirlpool. 12" DEEPER 14" 14" DEEPER 15" I bar mounting plate Bump out mounting bracket
  • Amana UMV1160CW | Installation Instructions - Page 4
    INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be in the foam cover the work surface. 1. Remove any remaining contents from the microwave oven cavity. 2. If the mounting plate is attached to the back of the microwave oven, remove it and set it aside.
  • Amana UMV1160CW | Installation Instructions - Page 5
    8. Lower blower motor back into the microwave oven. A A. Exhaust Port 9. Using diagonal wire cutting pliers, gently snip out the rectangular damper vent covers at the perforations. Roof Venting Installation Only 1. Repeat Step 1 from "Wall Venting Installation Only." 2. Repeat Step 2 from "Wall
  • Amana UMV1160CW | Installation Instructions - Page 6
    plate) B. Cabinet opening vertical centerline C. Wall stud centerlines D. Holes for lag screws E. Support tabs F. Mounting plate center markers Mark Rear Wall The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of 1 lag screw, preferably 2. 1. Using
  • Amana UMV1160CW | Installation Instructions - Page 7
    level line with each other. They must each be 141⁄8" (35.96 cm) from the centerline. 5. With the support tabs facing forward (see illustrations in the "Locate Wall Stud(s)" section), align the mounting plate center markers to the centerline on the wall, making sure its bottom edge is aligned to the
  • Amana UMV1160CW | Installation Instructions - Page 8
    at One End Hole (Figure 3) 1. With the support tabs of the mounting plate facing forward, insert a 3/16-24 x bottom. The template has trim lines to use as guides. ■■ If the wall behind the microwave oven sure the "Rear Wall" arrows align to the thickest part of t he rear wall (for example, the
  • Amana UMV1160CW | Installation Instructions - Page 9
    Weight Hazard Use two or more people to move and install microwave oven. Failure to do so can result in back or other injury. A B A. Mounting plate B. Support tabs 5. With front of microwave oven still tilted, thread power supply cord through the power supply cord hole in the bottom of the upper
  • Amana UMV1160CW | Installation Instructions - Page 10
    A AA. .BBooltslts NOTE: Avoid damage to the mounting nut, screw the bolts into the mounting nut holes around 15-20 mm by hand first, problem continues, call an electrician. ■■ Check that the power supply cord is plugged into a grounded 3 prong outlet. ■■ See the User Instructions for troubleshooting
  • Amana UMV1160CW | Installation Instructions - Page 11
    VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/ contractor reference only. NOTES: ■■ Vent materials needed for installation are not provided with microwave hood combination. ■■ We do not recommend using a flexible metal vent. ■■ To avoid possible
  • Amana UMV1160CW | Installation Instructions - Page 12
    in the User Guide. Accessories Filler Panel Mounting Screw Kit (includes parts A-G in "Parts Supplied" in the "Tools and Parts" section) A A. Filler panels Filler Panel Kits: 8171336 White 8171337 Black 8171338 Biscuit 8171339 Stainless Steel 99403 Almond See your authorized dealer or service
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See the “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration
in these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY
W11359526A
MICROWAVE HOOD COMBINATION SAFETY
..................................
1
INSTALLATION REQUIREMENTS
.......................................................
2
Tools and Parts
..................................................................................
2
Remove Cardboard Template
............................................................
2
Location Requirements
......................................................................
2
Product Dimensions
...........................................................................
3
Electrical Requirements
.....................................................................
3
INSTALLATION INSTRUCTIONS
.........................................................
4
Remove Mounting Plate
....................................................................
4
Rotate Blower Motor
..........................................................................
4
Locate Wall Stud(s)
............................................................................
6
Mark Rear Wall
...................................................................................
6
Drill Holes in Rear Wall
.......................................................................
7
Attach Mounting Plate to Wall
...........................................................
7
Prepare Upper Cabinet
......................................................................
8
Install Damper Assembly
...................................................................
9
Install the Microwave Oven
................................................................
9
Complete Installation
.......................................................................
10
VENTING DESIGN SPECIFICATIONS
...............................................
11
ASSISTANCE
......................................................................................
12
Replacement Parts
..........................................................................
12
Accessories.
.....................................................................................
12