Asus VivoMini UN65U commercial UN65UInstallationGuideEnglish
Asus VivoMini UN65U commercial Manual
 |
View all Asus VivoMini UN65U commercial manuals
Add to My Manuals
Save this manual to your list of manuals |
Asus VivoMini UN65U commercial manual content summary:
- Asus VivoMini UN65U commercial | UN65UInstallationGuideEnglish - Page 1
First Edition October 2016 UN65U Installation Guide Your VivoMini comes with the following items. Please contact ASUS Service Center if you cannot find the SO-DIMMs to the VivoMini's DIMM slots. NOTE: Some models may only support up to a maximum of 8GB memory To install or upgrade the memory - Asus VivoMini UN65U commercial | UN65UInstallationGuideEnglish - Page 2
the screw holes and fasten it using a 3mm round screw. 8 5. Follow steps 7-8 on pages 4-5 under the Installing or upgrading memory modules section of this guide to replace the bottom cover back on your VivoMini. 3. Connect the bundled HDD cable to the HDD, then secure the HDD and bracket to
-
1 -
2
 |
 |
2
3
4
5
6
E12147
First Edition
October 2016
UN65U Installation Guide
IMPORTANT!
•
It is recommended that you install or upgrade the memory modules, wireless
card, and solid state drive (SSD), under professional supervision. Visit an ASUS
service center for further assistance.
•
Ensure that your hands are dry before proceeding with the rest of the installation
process. Before installing any of the features in this guide, use a grounded wrist
strap or touch a safely grounded object or metal object to avoid damaging them
due to static electricity.
Your VivoMini comes with the following items. Please contact ASUS Service Center if you cannot
find the following items:
•
4 pcs holed rubber foot
•
2 pcs 2mm round screws, 1 hexagon screw
•
4 pcs 3mm round screws, 4 pcs 2mm round screws (on selected models)
•
2 pcs HDD bracket (on selected models)
•
1 pc HDD cable (on selected models)
15060-69320000
To install or upgrade the memory modules:
1.
Turn off your VivoMini then disconnect all cables and peripherals.
2.
Place the VivoMini on a flat stable surface, with its top side facing down.
3.
Using a flat-head screwdriver or straightened paper clip, remove the rubber feet from
the bottom side and set them aside, then remove the four (4) screws securing the cover.
Your VivoMini comes with two SO-DIMM memory slots that allow you to install two 2GB, 4GB,
8GB, or 16GB unbuffered with non-ECC 1.35 V DDR4 260-pin SO-DIMMs for a maximum of 32GB
memory.
Installing or upgrading memory modules
IMPORTANT!
Refer to http://www.asus.com for the list of compatible DIMMs. You can
only install DDR4 SO-DIMMs to the VivoMini’s DIMM slots.
NOTE:
Some models may only support up to a maximum of 8GB memory
NOTE:
The illustrations in this guide are for reference only. The slots may vary
depending on model.
4.
Get one screw from the ones you previously removed then place it into the hole.
Leave a portion of the screw head that would be enough for you to hold.
IMPORTANT!
Take note of the orientation of the holed rubber foot on the cover, and
the number printed under each rubber foot. These indicate the sequence you must
follow when removing the rubber foot from its slot. Refer to the following illustration
for details.
5.
Hold the screw then gently pull out the cover from the bottom side of the VivoMini.
Use your other free hand to hold the VivoMini in place.
6.
Align and insert the memory module into the slot (A) and press it down (B) until it is
securely seated in place. Repeat the same steps to install the other memory module.
IMPORTANT!
Always install into the lower slot first.
7.
Remove the screw you previously attached on the bottom cover (A), then align and
insert the bottom cover back on your VivoMini (B)
8.
Reattach the screws to secure the cover back on the bottom side of the main box, then
replace the rubber feet back on each screw hole.
IMPORTANT!
Take note of the orientation of the holed rubber foot on the cover, and
the number printed under each rubber foot. These indicate the sequence you must
follow when replacing the rubber foot back into each slot. Refer to the following
illustration for details.
Installing or upgrading the M.2 SSD
To install or upgrade a half-size M.2 SSD:
1.
Follow steps 1-5 on pages 2-3 under the
Installing or upgrading memory modules
section
of this guide to remove the bottom cover of your VivoMini.
2.
Insert the hexagon screw, as illustrated.
Your VivoMini includes a PCIe slot that supports a full-size or a half-size M.2 SSD.
4.
Gently push down the half-size M.2 SSD on top of the screw hole and fasten it using a
3mm round screw. Refer to the illustration for the location of the screw hole.
3.
Align and insert the half-size M.2 SSD into its slot inside the VivoMini. Refer to the illustration
for its location.
5.
Follow steps 7-8 on pages 4-5 under the
Installing or upgrading memory modules
section
of this guide to replace the bottom cover back on your VivoMini.