Behringer LC2412 Manual
Behringer LC2412 Manual
 |
View all Behringer LC2412 manuals
Add to My Manuals
Save this manual to your list of manuals |
Behringer LC2412 manual content summary:
- Behringer LC2412 | Manual - Page 1
User Manual EUROLIGHT LC2412 Professional 24-Channel DMX Lighting Console - Behringer LC2412 | Manual - Page 2
2 EUROLIGHT LC2412 User Manual Table of Contents Thank you 2 Important Safety Instructions 3 Legal Disclaimer 3 Limited Warranty 3 1. Introduction 4 2. Control Elements 5 3. Presets 10 4. The B Memory Section 11 5. Sound-to-Light 13 6. Chase Control 13 7. Additional Functions of the LC2412 - Behringer LC2412 | Manual - Page 3
EUROLIGHT LC2412 User Manual Important Safety Instructions the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid 13. Unplug this apparatus of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has - Behringer LC2412 | Manual - Page 4
EUROLIGHT LC2412 User Manual 1. Introduction This user's manual is designed to give you an overview of all the controls, so that you get to know all possible applications the LC2412 offers. General safety instructions are followed by a structured overview of the control -minded BEHRINGER technology - Behringer LC2412 | Manual - Page 5
back and forth between individual steps of a single chase manually or automatically. Preview With this function, you can preview stored for song pauses. MIDI The LC2412 can be controlled via MIDI. Two EUROLIGHT LC2412s can be operated as master and slave by using the MIDI interface. Entire shows - Behringer LC2412 | Manual - Page 6
EUROLIGHT LC2412 User Manual (10) (11) (5) (1) (2) Fig. 2.1: Section overview (4) (3) (8) (9) (6) (7) 2.1 Control elements of the A PRESET section (33) (12) 2.2 Control used for setting up a preset that can be directly recalled by moving fader A (41). As in all other setups, the MAIN fader - Behringer LC2412 | Manual - Page 7
7 EUROLIGHT LC2412 User Manual Exception: When the LC2412 is in preset mode ("P" shown in the bank display), the faders control the same channels as the faders of the A PRESET section. This way, you can simul-taneously create a second preset. (14) - (17) These faders are also a - Behringer LC2412 | Manual - Page 8
Control elements of the programming section ( 5 ) Despite its compact size, the EUROLIGHT LC2412 MIDI and SELECT SPECIAL. Further information about these functions is to be found in chapters 7 and 8, "ADDITIONAL FUNCTIONS OF THE LC2412" and "DIMMER CONTROL has to be manually activated in memory mode - Behringer LC2412 | Manual - Page 9
9 EUROLIGHT LC2412 User Manual (42) B fader. This fader is the master control for the B MEMORY section; it DMX channels are at your disposal. (59) MIDI IN connector. Used to feed in MIDI data (e.g. from a MIDI sequencer or another LC2412) to control the LC2412. (60) ANALOG IN connector. Connect an - Behringer LC2412 | Manual - Page 10
EUROLIGHT LC2412 User Manual your BEHRINGER EUROLIGHT LC2412. The LC2412 LC2412 is now in upper mode, that is, that the faders of the A PRESET section now control channels 13 - 24. The faders from the B MEMORY section affect channels 13 - 24 while in preset mode. 2. Set up your preset by moving - Behringer LC2412 | Manual - Page 11
the control LEDs. 3. Move the master B fader downward, then move the master A fader upward. Preset B is faded out, while preset A is faded in (manual The setup can only be observed on the control LEDs. The remaining functions of the EUROLIGHT LC2412 remain active. After you press the preview key, - Behringer LC2412 | Manual - Page 12
EUROLIGHT LC2412 User Manual 4.2 Crossfading between different setups 4.2.1 Crossfading between presets and memories Crossfading between memories and presets works exactly the same way as crossfading between two presets. The only difference is that the EUROLIGHT LC2412 respective control lights). - Behringer LC2412 | Manual - Page 13
13 EUROLIGHT LC2412 User Manual 4.4 Programming memories without direct control (Blind) In addition to programming memories by using the preview function (see chapter 4.1.3), you can also program memories using yet another method, without being visible - Behringer LC2412 | Manual - Page 14
to "0" (faded out). 2. Press INSERT or MANUAL. 3. Disable SOUND or RUN mode. 4. Select a chase containing no programmed steps. 6.2.1 Chase control through music When an audio signal source is connected at the ANALOG IN connector (60) at the rear of your EUROLIGHT LC2412, the speed of chases can be - Behringer LC2412 | Manual - Page 15
15 EUROLIGHT LC2412 User Manual Each step is shown in the display; the STEP key is disabled. If you additionally enable the INSERT key, you can fade in and out between the two steps selected last. Key On Off INSERT • MANUAL • Table. 6.4: Fading in and out via X-Fade fader 6.2.4 Manual - Behringer LC2412 | Manual - Page 16
16 EUROLIGHT LC2412 User Manual and turning the DATA wheel. The chase selected will be indicated on the control lights as long as you keep the key pressed. Releasing "Hold" MAIN fader all the way down and then all the way up. Moving up the fader crossfades between the former setup and the new one. - Behringer LC2412 | Manual - Page 17
chart as well as the required information on individual controllers can be found in this manual's appendix. 7.5.1 Cascading two EUROLIGHT LC2412s Using MIDI also lets you cascade a second LC2412 to your console. To this end, connect the MIDI OUT connector (58) of the first console (transmitting unit - Behringer LC2412 | Manual - Page 18
18 EUROLIGHT LC2412 User Manual MIDI Out PC with MIDI-software MIDI In LC2412 rear DMX512 Out DMX512 In 7.7 Adjusting differing illumination levels The EUROLIGHT LC2412 lets you settings relevant to the console's functions are reset to their factory settings (SOLO ALL ENABLED, CURVE ALL LINEAR). - Behringer LC2412 | Manual - Page 19
19 EUROLIGHT LC2412 User Manual 8. Dimmer Control 8.2 Digital control via DMX512 Dimmerpack DMX512 output DMX512 input LC2412 rear 0-10 V switch box Analog output 0-10 V Analog input Tape/Send output 8.2.1 Digital control features The EUROLIGHT LC2412 features a modern digital interface - Behringer LC2412 | Manual - Page 20
20 EUROLIGHT LC2412 User Manual DMX channels A DMX channel consists out of one digitally transmitted information unit (1 Byte/8 Bit), whereas 256 different information units can be transmitted. These units are - Behringer LC2412 | Manual - Page 21
9.1: Cable layout of the sub D connection 9.3.3 MIDI connection Coonect to other MIDI equipment or another EUROLIGHT LC2412 by using common MIDI cables. The cables should never be longer than 15 m (45 ft). 9.3.4 Audio connections To control the EUROLIGHT LC2412 via an audio signal, please use a mono - Behringer LC2412 | Manual - Page 22
EUROLIGHT LC2412 User Manual 10. Specifications CHANNELS 26 (24 + 2 special switchable channels) DMX 78 out of 512 DMX channels (max. 3 DMX channels per console-channel) MEMORIES max. 120 CHASES max. 99 Steps max. 650, up to 99 per chase Inputs Analog In Level Footswitch MIDI BEHRINGER - Behringer LC2412 | Manual - Page 23
23 EUROLIGHT LC2412 User Manual Function Midi Channel Mode Note Number Velocity After Touch Pitch Bender Control Change 0 1 Flash 11 Key Flash 12 Bank Chaser Nr. Key Channel Flash Key Solo Special 1 Special 2 Key Manual Y Y Sound/Run Y Y Insert Y Y Key Preset Y Y Key Memory N N - N - Behringer LC2412 | Manual - Page 24
24 EUROLIGHT LC2412 User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION EUROLIGHT LC2412 Responsible Party Name: Address: Phone/Fax No.: MUSIC Group Services US Inc. 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA Phone: +1 425 672 0816 Fax: +1 425 673 7647 EUROLIGHT - Behringer LC2412 | Manual - Page 25
We Hear You
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
 |
 |
User Manual
EUROLIGHT LC2412
Professional 24-Channel DMX Lighting Console