Biostar P4TPT800 P4TPT BIOS setup guide

Biostar P4TPT800 Manual

Get Biostar P4TPT800 PDF manuals and user guides View all Biostar P4TPT800 manuals
Add to My Manuals
Save this manual to your list of manuals

Biostar P4TPT800 manual content summary:

  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 1
    P4TPT BIOS Setup BIOS Setup 1 1 Main Menu 3 2 Standard CMOS Features 6 3 Advanced BIOS Features 9 4 Advanced Chipset Features 12 5 Integrated Peripherals 15 6 Power Management Setup 19 7 PnP/PCI Configurations 24 8 PC Health Status 26 9 Frequency Control 27 i
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 2
    password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system. The rest of this manual is intended to guide you through the process of configuring your system using Setup. Plug and Play Support These AWARD BIOS supports the Plug and Play Version
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 3
    Version 2.1 of the Intel PCI (Peripheral Component Interconnect) local bus specification. DRAM Support DDR DRAM (Double Data Rate Synchronous DRAM) are supported. Supported CPUs This AWARD BIOS supports the Intel Pentium ® 4 CPU. Using Setup In general, you use the arrow keys to highlight items
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 4
    WARNING !! The information about BIOS defaults on manual (Figure 1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS installed on board, for update options. Advanced BIOS Features This submenu allows you to configure enhanced features of the BIOS. Advanced Chipset Features This
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 5
    P4TPT BIOS Setup Integrated Peripherals This submenu allows you to configure certain IDE M/B damage!) Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence. These configurations are factory settings optimized for
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 6
    all configuration changes to CMOS(memory) and exit setup. Confirmation message will be displayed before proceeding. Exit Without Saving Abandon all changes made during the current session and exit setup. Confirmation message will be displayed before proceeding. Upgrade BIOS This submenu allows you
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 7
    P4TPT BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 8
    P4TPT BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu. Item Options Description Date mm : dd : yy Set
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 9
    , but Diskette All, but Disk/ Key N/A N/A N/A Description Select the situation in which you want the BIOS to stop the POST process and notify you. Displays the amount of conventional memory detected during boot up. Displays the amount of extended memory detected during boot up. Displays the total
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 10
    used to protect the IDE Hard Disk boot sector. If this function is enabled and an attempt is made to write to the boot sector, BIOS will display a warning message on the screen and sound an alarm beep. Enabled Virus protection is activated. Disabled (default) Virus protection is disabled. CPU
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 11
    controls Gate A20. Fast (default) Lets chipset control Gate A20. Typematic Rate Setting When BIOS to the operating system. The Choices: Enabled (default), Disabled. MPS Version Control For OS The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor specification. Select version supported
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 12
    P4TPT BIOS Setup OS Select For DRAM > 64MB A choice other than Non-OS2 is only used for OS2 systems with memory exceeding 64MB. The Choices: Boot Seq & Floppy Setup First/ Second/ Third/ Boot Other Device These BIOS attempt to load the operating system from the device in the sequence selected in
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 13
    BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system. This chipset manage bus speeds and access to system memory DRAM timing. The Choices: By SPD (default), Manual. CAS Latency Time When synchronous DRAM is installed
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 14
    , a system error may result. The Choices: Enabled (default), Disabled. Video BIOS Cacheable Select Enabled allows caching of the video BIOS, resulting a better system performance. However, if any program writes to this memory area, a system error may result. The Choices: Disabled (default), Enabled
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 15
    P4TPT BIOS Setup Delayed Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1. The Choices: Enabled (default), Disabled. AGP Aperture Size (MB) Select the size of the
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 16
    P4TPT BIOS Setup 5 Integrated Peripherals ! Figure 5. Integrated Peripherals Onboard CMI Enabled (default), Disabled. USB Keyboard Support The default value is Disabled. Enabled Disabled (default) Enable USB Keyboard Support. Disable USB Keyboard Support. AC97 Audio/ Modem This item allows
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 17
    P4TPT BIOS Setup Init Display First This item allows you to decide to active whether PCI Slot or on-chip VGA first. The Choices: AGP (default), PCI Slot. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read / write. If your IDE hard drive supports
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 18
    P4TPT BIOS Setup The Choices: Half (default), Full. Onboard Parallel Port This fields let you set a PIO mode (0-4) for each of the IDE devices that the onboard IDE interface supports. Modes 0 to 4 will increased performance progressively. In Auto mode, the system automatically determines the best
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 19
    IDE hard drives in your system. As well, your operating environment requires a DMA driver (Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/100, select Auto to enable BIOS support. The Choices: Auto (default), Disabled. 18
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 20
    run VGA BIOS to initialize the VGA card when system wakes up from S3 state . The system time is shortened if you disable the function , but system will need AGP driver to initialize the card . So , if the AGP driver of the VGA card does not support the initialization feature , the display may work
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 21
    P4TPT BIOS Setup Power Management This category allows you to select the type (or degree) of power saving and is directly related to the following modes: 1.HDD
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 22
    P4TPT BIOS Setup Video Off In Suspend This determines the manner in which the monitor is blanked. The Choices: Yes (default), No. Suspend Type This item allows
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 23
    BIOS this function, you need a LAN add-on card which support power on function. It should also support the wake-up on LAN jumper. The Choices: Enabled, subsequent manual intervention. There are 3 sources that provide current to the CMOS area that retains these Power-On instructions; the motherboard
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 24
    P4TPT BIOS Setup used. There are 3 options: "Former-Sts", "On", "Off". "Off" (default) power is lost. Means always set CMOS to the "Off" status when AC "On"
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 25
    Reset Configuration Data The system BIOS supports the PnP feature which requires update ESCD to the memory locations. These locations (4K) are reserved in the system BIOS. If the Disabled settings will be shown on the screen only if "Manual" is chosen for the resources controlled by function. Legacy
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 26
    Setup Resources Controlled By By Choosing "Auto(ESCD)" (default), the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral.By Choosing "Manual", the user will need to assign IRQ & DMA for add-on cards. Be sure that there are no
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 27
    P4TPT BIOS Setup 8 PC Health Status ! Figure 8. PC Health Status Shutdown Temperature This item allows you to set up the CPU shutdown Temperature. This item only effective
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 28
    P4TPT BIOS Setup 9 Frequency Control ! Figure 9. Frequency Control CPU Clock Ratio This item allows you to select the CPU Ratio. CPU Voltage This item allows you to
  • Biostar P4TPT800 | P4TPT BIOS setup guide - Page 29
    P4TPT BIOS Setup CPU Clock This item allows you to select CPU Clock, and CPU over clocking. If unfortunately, the system's frequency that you are selected is
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
P4TPT BIOS Setup
i
BIOS Setup
.......................................................................................
1
1 Main Menu
...................................................................................................
3
2 Standard CMOS Features
.............................................................................
6
3 Advanced BIOS Features
.............................................................................
9
4 Advanced Chipset Features
........................................................................
12
5 Integrated Peripherals
.................................................................................
15
6 Power Management Setup
..........................................................................
19
7 PnP/PCI Configurations
..............................................................................
24
8 PC Health Status
.........................................................................................
26
9 Frequency Control
......................................................................................
27