Home » Bosch Manuals » Laundry Dryers » Bosch WTG865H3UC » Manual Viewer

Bosch WTG865H3UC Use and Care Manual

Bosch WTG865H3UC Manual

View all Bosch WTG865H3UC manuals

Add to My Manuals
Save this manual to your list of manuals

Bosch WTG865H3UC manual content summary:

Bosch WTG865H3UC | Use and Care Manual - Page 1
en-us Use and Care Manual, Installation Instructions Dryer WTG865H3UC
Bosch WTG865H3UC | Use and Care Manual - Page 2
you will enjoy the superior performance and reliability. Please do not hesitate to contact our Customer Service department if you have any questions or comments about your new dryer. Thank you for choosing Bosch®. Visit our website at www.boschhome.com/us for more information and to view a selection
Bosch WTG865H3UC | Use and Care Manual - Page 3
information 4 Customer service 5 Your dryer is intended for 6 Safety Definitions 6 IMPORTANT SAFETY INSTRUCTIONS 7 Introduction to of drain hose 41 Troubleshooting 42 Introduction 42 General Troubleshooting 42 STATEMENT OF LIMITED PRODUCT WARRANTY .. 45 Bosch® Clothes Dryer 45 3
Bosch WTG865H3UC | Use and Care Manual - Page 4
and services can be found at www.boschhome.com/us and in the online shop www.bosch- your new Bosch® dryer. This information will be helpful in the event you need to contact Customer Service or would of Purchase Where Purchased E-Nr ex: WTG865H3UC/01) FD ex: 9709|90007, provides production date)
Bosch WTG865H3UC | Use and Care Manual - Page 5
with your dryer, please consult the Troubleshooting section of this manual. ~ Troubleshooting; Page 42 If a technician comes out to advise you of information that is in the Troubleshooting table you may be charged. If problems persist and service becomes necessary, contact your dealer, installer
Bosch WTG865H3UC | Use and Care Manual - Page 6
. Before using the appliance, read the use and installation instructions and all other information included with the appliance and act . Safety Definitions Important SafetyDintso safety information is contained in this manual and on the warning labels located on your dryer. Standard symbols
Bosch WTG865H3UC | Use and Care Manual - Page 7
with the controls. ▯ Do not repair or replace any part of the appliance or attempt any service unless specifically recommended in the user maintenance instructions or in Bosch® published user-repair instructions that you understand and have the skills to carry out. ▯ Do not use fabric softeners or
Bosch WTG865H3UC | Use and Care Manual - Page 8
following label as required by California: 67$7(2)&$/,)251,$352326,7,21:$51,1* :$51,1* &DQFHUDQG5HSURGXFWLYH+DUPZZZ3:DUQLQJVFDJRY SAVE THESE INSTRUCTIONS! Keep these instructions for future reference and in case of change of ownership, manual should be conveyed with the dryer. 8
Bosch WTG865H3UC | Use and Care Manual - Page 9
information Thank you for choosing Bosch® for your laundry appliance needs. Please read and follow the use and care, important safety instructions and troubleshooting information contained in this manual. Please retain this manual for future reference. ~ Troubleshooting; Page 42 This dryer complies
Bosch WTG865H3UC | Use and Care Manual - Page 10
Dimensions and clearances required Installation for best performance Dimensoadclernsquired Appliance dimensions 9 CAUTION DO NOT INSTALL THE DRYER: ▯ outdoors, ▯ in an environment with dripping water, ▯ near flammable materials, ▯ in rooms which are at risk of freezing, ▯ in rooms which may
Bosch WTG865H3UC | Use and Care Manual - Page 11
Minimum clearances Closet: Stacked ( + ) * % & $ Label Dimension U.S. Metric Inches cm E & F are minimum area size! E Top Vent 63 sq. 404 sq. F Bottom Vent 63 sq. 404 sq. Vent spacing is actual (not minimum dimensions) G 37 94 H 26 66 J 3 7.6 K 29 73.6 Under counter (
Bosch WTG865H3UC | Use and Care Manual - Page 12
Under counter (Less Desirable) ( + * ) If front of the appliance is covered ventilation openings must be installed. E & F are minimum area sizes E 63 sq.in. 404 sq. cm F 63 sq.in. 404 sq. cm G & H actual spacing dimensions for min. open area sizes G 3 in. 7.6 cm H 14 in. 35.6 cm
Bosch WTG865H3UC | Use and Care Manual - Page 13
must be performed by a qualified installer, according to these instructions and according to all local codes. ▯ In addition to the installation and safety information in this manual, the local water and electric authorities (services) may have special requirements that must be followed. ▯ Install
Bosch WTG865H3UC | Use and Care Manual - Page 14
remove this item before using the dryer. @ literature pack contents: ▯ User Manual and Product Registration ▯ (2) plastic ties for securing drain hose ▯ Plastic connector ▯ Summary of drain hose installation instructions NOTICE: If any parts are missing please notify your dealer immediately. 14
Bosch WTG865H3UC | Use and Care Manual - Page 15
item number: WMZ20500 Stacking kits The dryer can be stacked on a Bosch® washer of the same dimensions to save space. Stacking kit without a item number: WMZ20600 Accessories can be purchased from Customer Service or your local dealer. ~ Customer service; Page 5 Installation - step by step 1. Unpack
Bosch WTG865H3UC | Use and Care Manual - Page 16
PD[LQ FP PLQLQFP PD[LQFP ▯ Sink/Basin or Floor drain: If using the elbow supplied on the hose re-position elbow closer to the drain end of hose and fasten with the plastic ties as shown in picture "C". & ▯ Sink Drain Pipe: Attach and secure drain hose as shown
Bosch WTG865H3UC | Use and Care Manual - Page 17
a 3-wire power cord follow the installation instructions for such in the next section of this manual. ALL ELECTRICAL CONNECTIONS AND CIRCUITS 9 WARNING electric shock hazard. Replacement power cords can be purchased through our Customer Service department. ▯ Use only a UL listed 30 amp power cord. ▯
Bosch WTG865H3UC | Use and Care Manual - Page 18
3-wire power supply cord 9 WARNING ELECTRIC SHOCK HAZARD To reduce risk of fire, electric shock, serious injury, or death follow the installation instructions below carefully or have work done by an qualified electrician. 4. Remove the 4-wire power cord (as supplied): A. Remove the 3 Philips screws
Bosch WTG865H3UC | Use and Care Manual - Page 19
top cover as previously described in "2" above. Integrated electrical receptacle This appliance is equipped with a 208/240V 15A receptacle for use ONLY with Bosch® washer. 9 CAUTION Do not use this receptacle to power any other device. If any other electrical device is plugged into this receptacle
Bosch WTG865H3UC | Use and Care Manual - Page 20
▯ If the dryer does not work, press the center of the Program Selector to switch off the appliance. Look in the Troubleshooting section of this user manual for hints in solving the problem. Preparing to transport the dryer - step by step 1. Press the center of the Program Selector to switch off the
Bosch WTG865H3UC | Use and Care Manual - Page 21
in position adjacent to the handle slots/openings and the hinge insert in the opposite position as shown. Reinstall the original screws. 6. Follow the instructions at images below to unlock the door ring from the door body. 7. Separate the ring from the door body and rotate the ring 180° from
Bosch WTG865H3UC | Use and Care Manual - Page 22
12.Install the door latch (1) and then door latch cover (2) on the opposite side of the door opening. 13.Install the door and hinge assembly back on the dryer with the original screws. 14.Confirm the door closes and latches in place. Plug in the dryer to operate it. 22
Bosch WTG865H3UC | Use and Care Manual - Page 23
Getting to know your appliance Control panel Getignowkyuraplince &RWWRQV (FR3HUIHFW 3UHZDVK (DV\&DUH 0L[HG)DEULFV 'HOLFDWHV6LON 6WDLQV :RRO 5LQVH 6SLQ 'UDLQ 6SHHG3HUIHFW 7HPSHUDWXUH :DWHU3OXV 5HGXFHG,URQLQJ 6SLQ 6WDUW 5HORDG ² )LQLVKHG,Q &KLOG/RFNVHF (
Bosch WTG865H3UC | Use and Care Manual - Page 24
Display area (FR3HU IHFW 3UHZDVK :DWHU3OXV 5HGXFHG,URQLQJ K 6WDLQV # 6WDUW 5HORDG 6SHHG3HUIHFW 7HPSHUDWXUH C ; 6SLQ 3 ² )LQLVKHG,Q &KLOG/RFNVHF + Buttons Button ( 0 8 Description Select Low Heat. Select Time Dry 5. Select Remote Start. Indicator { e.g. 0 Remote start
Bosch WTG865H3UC | Use and Care Manual - Page 25
Other indicators Indicator E Description Lit: Child lock activated Flashing: A change to the programs or options is not allowed because Child lock is activated. Flashing will stop after a few seconds. é Clean lint filter or heat exchanger DR Check drain indicator | OFF: Wi-Fi is off.
Bosch WTG865H3UC | Use and Care Manual - Page 26
SHOCK, OR INJURY To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS and OPERATING INSTRUCTIONS before operating this appliance. Your new dryer # 3 + ( Control panel, display area, program selector 0 Drum with interior light (depending on
Bosch WTG865H3UC | Use and Care Manual - Page 27
and operating instructions. Check the machine. Never connect the utilities (power or water) to or start a damaged machine! Contact Customer Service! ~ Customer service; Page 5 off the dryer. Look in the Troubleshooting section of the operating instructions for support. ~ Troubleshooting; Page 42 27
Bosch WTG865H3UC | Use and Care Manual - Page 28
Temporary disconnection of the dryer Operate your dryer only when you are at home. If you intend going on vacation or are not using your dryer for an extended period of time, you should: 1. Turn off the circuit breaker. 2. Pull out the power supply plug if possible. 3. Clean the lint filter. Using
Bosch WTG865H3UC | Use and Care Manual - Page 29
no foreign objects are in the drum. Recommended Load Size Recommended maximum load size can be found in the program selection table in this manual. ~ Program selection table; Page 36 The Start/Pause indicator light starts flashing. 2. Press the Start/Pause button. Indicator lamp lights up and the
Bosch WTG865H3UC | Use and Care Manual - Page 30
Indicator of program sequence Bosch® dryers use an advanced control system which continually monitors the laundry's remaining moisture. The current state of the process and status of the program is
Bosch WTG865H3UC | Use and Care Manual - Page 31
of the Home Connect function depends on the availability of Home Connect services in your country. You can find information on this at: www.home-connect.com Notes ▯ Please observe the safety precautions in this instruction manual and make sure that these are complied with even when operating the
Bosch WTG865H3UC | Use and Care Manual - Page 32
Home Connect menu; Page 31 Make sure that you have opened the Home Connect app and are logged in. 1. Set the program to position 3. †'˜ (connect manually) appears in the display. 2. Press Start/Pause. The appliance now sets up its own Wi-Fi network with the name (SSID) Home Connect. '˜˜ (connect
Bosch WTG865H3UC | Use and Care Manual - Page 33
appliance. As soon as a new software update is available, a message appears in the display: -˜š Install the update directly via the message in the display or manually as follows: Ensure that you are in the Home Connect menu. ~ Calling up the Home Connect menu; Page 31 1. Set the program to position
Bosch WTG865H3UC | Use and Care Manual - Page 34
and smart devices. This module is integrated at the factory, under direct control of B/S/H Home Appliances Corporation, and is not user serviceable or upgradable. At least 20cm separation distance should be maintained from device to user. FCC COMPLIANCE STATEMENT 9 CAUTION Changes or modifications
Bosch WTG865H3UC | Use and Care Manual - Page 35
the drying results. ▯ When washing laundry to be tumble-dried, use the correct amount of detergent and textile care products as specified in the manufacturer's instructions. ▯ Clean the moisture sensor regularly. ~ Cleaning the moisture sensors; Page 41 35
Bosch WTG865H3UC | Use and Care Manual - Page 36
Program selection table Progamselctinoable Programs Max. load Type of laundry up to: Cotton full load Normal cotton and linen type load (bed linen, cotton clothes, terry bathrobes etc.) Towels 1/2 load Terrycloth type laundry e.g. towels and bathrobes Anti Shrink 1/3 load Cotton or linen
Bosch WTG865H3UC | Use and Care Manual - Page 37
Optional program settings Low Heat Optinaolrgmsetign Reduced temperature for delicate fabrics, e.g. polyacrylic, polyamide or elastane, with longer drying time. Observe the care information or symbols on the textile's label. Time Dry 5 Available only for Time programs: 5 Air Fluff and 5 Time Dry, ~
Bosch WTG865H3UC | Use and Care Manual - Page 38
Appliance settings Child lock Apliancestign You can secure the appliance against inadvertent changing of the set functions. To do this, activate the Child lock after cycle start. To Activate/Deactivate, press Finish in M and N for approximately 3 seconds. In the display field, you will see the D
Bosch WTG865H3UC | Use and Care Manual - Page 39
Your appliance is designed to give you years of service. Observe the following instructions to maintain your appliance and keep it in top operating condition. Cleaning the lint filter A dirty filter extends the drying time and increases energy consumption. 9
Bosch WTG865H3UC | Use and Care Manual - Page 40
4. Open the filter. 5. Remove fluff (run hand over filter). Cleaning the heat exchanger The heat exchanger requires periodic cleaning (recommended once per month under normal drying conditions). The frequency of cleaning depends on the amount and type loads being dried. To clean the heat exchanger:
Bosch WTG865H3UC | Use and Care Manual - Page 41
maintenance flap until it locks into position. 13. Look in the Troubleshooting table to reset the maintenance indication. ~ Troubleshooting; Page 42 NOTICE: Use white vinegar only! Clean the moisture sensors up after the maintenance, you should contact Customer Service or your local dealer. 41
Bosch WTG865H3UC | Use and Care Manual - Page 42
the power outlet. 3. Call Customer Service. ~ Customer service; Page 5 General Troubleshooting Often when you encounter a problem it will be something minor. Before you call Customer Service, consider the suggestions and instructions below: NOTICE: The troubleshooting items listed below can help
Bosch WTG865H3UC | Use and Care Manual - Page 43
Determing the Problem Problem Possible cause(s) Dryer does not start. Start/Pause indicator light does not illuminate. Power cord end not inserted at all or not inserted correctly. A fuse
Bosch WTG865H3UC | Use and Care Manual - Page 44
Connect™ is not working. ▯ You can find solutions to problems with Home Connect at www.home-connect.com. ▯ The use of the Services in your country. Check here, www.home-connect.com, to see if the Home Connect services are available in your area and further information. If troubleshooting
Bosch WTG865H3UC | Use and Care Manual - Page 45
730) days from the date of purchase, labor charges excluded. Repair/Replace as Your Exclusive Remedy: During this warranty period, Bosch® or one of its authorized service providers will repair your Product without charge to you (subject to certain limitations stated herein) if your Product proves to
Bosch WTG865H3UC | Use and Care Manual - Page 46
to follow operating instructions, mishandling, unauthorized service (including self wrong with the Product; correction of installation problems (you are solely responsible for any structure and DIRECT DAMAGES WHICH ARE DEFINITELY CAUSED EXCLUSIVELY BY BOSCH®, OR OTHERWISE. SOME STATES DO NOT ALLOW
Bosch WTG865H3UC | Use and Care Manual - Page 47
47
Bosch WTG865H3UC | Use and Care Manual - Page 48
*9001426856* 9001426856 9907 1901 Main Street, Suite 600 • Irvine, CA 92614 • 1-800-944-2904 www.bosch-home.com • © 2018 BSH Home Appliances Corporation

Section	Page
en-us Use and Care Manual, Installation Instructions	1
Dryer	1
Welcome to Your New Dryer!	2
Congratulations on your selection of a new Bosch® dryer for your laundry needs. We are confident you will enjoy the superior performance and reliability.	2
Please do not hesitate to contact our Customer Service department if you have any questions or comments about your new dryer.	2
Thank you for choosing Bosch®.	2
Visit our website at www.bosch- home.com/us for more information and to view a selection of our products.	2
Table of contentsen-us Use and Care Manual, Installation Instructions	3
Your dryer is intended for 6	3
Safety Definitions 6	3
IMPORTANT SAFETY INSTRUCTIONS 7	3
Introduction to your new dryer 9	3
Dimensions and clearances required 10	3
INSTALLATION INSTRUCTIONS 13	3
Getting to know your appliance 23	3
OPERATING INSTRUCTIONS 26	3
Home Connect™ 31	3
Laundry 35	3
Program selection table 36	3
Optional program settings 37	3
Appliance settings 38	3
USER-MAINTENANCE INSTRUCTIONS 39	3
Troubleshooting 42	3
STATEMENT OF LIMITED PRODUCT WARRANTY 45	3
Important information	4
Important information	4
Purchase information	4
Customer service	5
1. Contact your installer or the Authorized Service Provider in your area and explain to them why you are not satisfied. This will usually correct the problem.	5
2. If after working with your installer or service technician the problem still has not been resolved to your satisfaction, please let us know either by writing to us at:	5
When writing or calling please have the following information available:	5
Your dryer is intended for	6
Your dryer is intended for	6
Safety Definitions	6
Safety Definitions	6
9 WARNING	6
9 CAUTION	6
NOTICE:	6
Tip:	6
IMPORTANT SAFETY INSTRUCTIONS	7
IMPORTANT SAFETY INSTRUCTIONS	7
READ AND SAVE THESE INSTRUCTIONS	7
WARNING	7
WARNING	7
WARNING	8
WARNING	8
Introduction to your new dryer	9
Introduction to your new dryer	9
9 WARNING	9
Risk of fire, electric shock or injury	9
Standard features and helpful information	9
Special features	9
Environmentally friendly use of your dryer	9
Dimensions and clearances required	10
Dimensions and clearances required	10
Installation for best performance	10
9 CAUTION	10
Do not install the dryer:	10
Tip:	10
Appliance dimensions	10
Length of power cord and drain hose	10
Minimum clearances	11
INSTALLATION INSTRUCTIONS	13
Installation Instructions	13
Introduction	13
9 WARNING	13
Risk of fire, electric shock or injury to persons	13
9 CAUTION	13
These installation instructions are intended for use by qualified installers. In addition to these instructions, the installation must comply with:	13
Before installing the dryer	13
9 CAUTION	13
Waste disposal	13
9 WARNING	13
Warnings for children	13
9 WARNING	13
To avoid risk of injury or death, do the following	13
Parts provided with your dryer	14
NOTICE:	14
Accessories for your appliance	15
Installation - step by step	15
1. Unpack the dryer.	15
2. Remove all objects from the dryer drum.	15
3. Check the dryer for visible damage.	15
4. Position the dryer near the installation location.	15
5. Disconnect the power cord and drain hose from their clips on the back of the dryer.	15
9 CAUTION	15
NOTICE:	15
6. Connect the outlet end of the drain hose to a standpipe or other drain inlet. Examples are shown below.	15
9 CAUTION	15
Appliance damage could occur if drain water flows back into the appliance	15
▯ Plumbing box or Standpipe connection:	15
1. Fasten the dryer drain hose to the washer drain/elbow as shown in picture “A”. Secure with plastic ties supplied.	15
9 CAUTION	15
2. Place drain hose assembly into standpipe as shown in picture “B”.	15
▯ Sink/Basin or Floor drain:	16
NOTICE:	16
▯ Sink Drain Pipe:	16
NOTICES	16
Electrical Connections	17
The attached power cord is a standard 4-wire dryer cord and is UL approved and listed in the USA and Canada. It meets the following requirements:	17
NOTICE:	17
9 WARNING	17
Electric shock hazard	17
9 WARNING	17
Electric shock hazard	17
To reduce the risk of electrical shock:	17
9 WARNING	17
Electric shock hazard	17
9 WARNING	17
Electric shock hazard	17
9 WARNING	18
Electric shock hazard	18
The power cord must meet the following requirements:	18
1. Unplug the current power cord being used from the outlet/receptacle.	18
2. To disconnect and/or reconnect a new power cord the top cover of the appliance must be removed as shown below.	18
A. Remove the two T20 torx head screws.	18
B. Push the top cover toward the rear of the appliance and lift up.	18
3. Open the connection box toward the rear of the appliance by removing the T20 torx head screw fastening the cover.	18
4. Remove the 4-wire power cord (as supplied):	18
A. Remove the 3 Philips screws (2 labeled L and one labeled N).	18
B. Remove the green grounding screw PE (T20 torx).	18
NOTICE:	18
5. Loosen the strain relief clamp screw (Philips head) on rear of the connection box.	18
6. Pull the old power cord out of the connection box.	18
7. Install the new power cord back through the strain relief clamp.	18
NOTICE:	18
8. Ensure the terminal ends are long enough and are formed (bent) so that no part of them (wires or terminal ends) come in contact with connection box enclosure.	18
NOTICE:	18
9. Ensure the terminal ends are long enough and are formed (bent) so they will align with the terminal block fastening locations (screw holes).	18
10. Reinstall the 2 terminal block screws (Philips head) at locations L as shown below.	18
11. If the ground wire shown below from N to PE is not part of the 3-wire cord assembly it must be obtained/ purchased separately and it must be installed.	18
12. Install the last terminal block screw (Philips) and 1 grounding screw (T20 torx) at locations N and PE.	18
13. Alternate Grounding Methode: Neutral wire of 3-wire cord (usually white or middle conductor) can be connected directly to PE as shown below.	19
Electric shock hazard	19
14. Tighten the strain relief screw ensuring the power cord cannot be pulled out of the connection box but not so tight as to cut the power cord insulation.	19
15. Reinstall the connection box cover making sure all wires are routed so they do not touch any part of the enclosure and are secure.	19
16. Reinstall the appliance top cover as previously described in “2” above.	19
9 CAUTION	19
9 CAUTION	19
Leveling the dryer	19
1. Install the dryer on a level and solid surface, preferably in a corner of a room.	19
2. If the floor is uneven (or not level) adjust the dryer feet as required to level the dryer. Do not place anything under the dryer feet to help level the dryer.	19
3. Extend the dryer feet no more than is necessary. The more the feet are extended, the more vibration the dryer will experience. Start with the dryer feet turned all the way in and adjust each foot as necessary.	19
4. Use a bubble level to check the top of the dryer to make sure it is level side to side and front to rear.	19
5. Press down on each corner of the dryer top to make sure the dryer does not “wobble“. There should be no \	19
Check heating system	20
1. Check that the drum is empty.	20
2. Close the dryer door.	20
3. Switch the dryer to the Cotton program and select Extra Dry dryness level.	20
4. Press the Start/Pause button.	20
5. After 2-3 minutes press the Start/Pause button and open the door.	20
Preparing to transport the dryer - step by step	20
1. Press the center of the Program Selector to switch off the appliance.	20
2. Pull out power supply plug.	20
3. Place any accessories in the drum.	20
4. Close the door and secure with adhesive tape.	20
5. Screw the height-adjustable feet of the dryer into the housing to prevent them from being damaged during transportation.	20
Reversing the door - step by step	20
Tip:	20
1. Press the center of the Program Selector to switch off the appliance. Remove the power plug from wall outlet. Open the door completely.	20
2. Remove the hinge screws from the dryer side then remove the door and hinge assembly from the dryer housing.	20
3. Place the door on a flat, smooth, secure surface such as a towel or cloth lying on the floor or table.	20
4. Remove screws from the hinge insert and then remove it from the door.	20
5. Remove screws from the hook insert and then remove it from the door.	21
6. Follow the instructions at images below to unlock the door ring from the door body.	21
7. Separate the ring from the door body and rotate the ring 180° from it's original position. Fit the ring back to the door body as shown below.	21
8. Follow the instructions of the images below to lock the door ring.	21
9. Place the hook insert in position adjacent to the handle slots/openings and the hinge insert in the opposite position as shown. Reinstall the original screws.	21
10. Remove screws from the door latch cover and then remove it from the dryer housing.	21
11. Remove the door latch from the dryer housing.	21
12. Install the door latch (1) and then door latch cover (2) on the opposite side of the door opening.	22
13. Install the door and hinge assembly back on the dryer with the original screws.	22
14. Confirm the door closes and latches in place. Plug in the dryer to operate it.	22
Getting to know your appliance	23
Getting to know your appliance	23
Control panel	23
Display area	24
OPERATING INSTRUCTIONS	26
Operating Instructions	26
9 WARNING	26
Risk of fire, electric shock, or injury	26
Your new dryer	26
9 WARNING	27
Before installing or using your dryer	27
Before using the dryer for the first time	27
1. Read these operating instructions carefully.	27
2. Check that the supply voltage corresponds with the voltage specifications on the rating plate on the dryer, see top rear side of the dryer and/or rating plate label inside the dryer door. ~ Electrical Connections; Page 17	27
3. Remove all objects from the drum.	27
4. Check the dryer for visible damage. If damage found contact your dealer.	27
5. Wipe the inside of the drum with a damp cloth.	27
6. Check heating system. ~ Check heating system; Page 20	27
7. If the dryer does not work, press the center of the Program Selector to switch off the dryer. Look in the Troubleshooting section of the operating instructions for support. ~ Troubleshooting; Page 42	27
Temporary disconnection of the dryer	28
1. Turn off the circuit breaker.	28
2. Pull out the power supply plug if possible.	28
3. Clean the lint filter.	28
Using the program selector to choose a drying program	28
NOTICE:	28
Program selection	28
Selecting optional program settings	28
Loading the laundry	29
9 WARNING	29
Risk of explosion	29
1. Check lint filter.	29
2. Load the laundry into the drum and close the door.	29
Tip:	29
Tips	29
Starting the program	29
1. Switch on the appliance. Rotate program selector to the desired program. Select the program which corresponds to the laundry in the dryer from Program selection table. ~ Program selection table; Page 36	29
2. Press the Start/Pause button. Indicator lamp lights up and the cycle starts.	29
NOTICES	29
3. If required, select Low Heat by pressing the button. ~ Low Heat; Page 37	29
4. If required, select Wrinkle Block™ by pressing the button. ~ Wrinkle Block™; Page 37	29
Indicator of program sequence	30
Selecting a different program	30
1. Press Start/Pause.	30
NOTICE:	30
2. Select another program and/or a different optional program setting.	30
NOTICE:	30
3. Press Start/Pause. The new drying cycle starts from the beginning.	30
Cancel program	30
1. Press Start/Pause.	30
2. Press the center of the Program Selector to switch off the appliance.	30
Program end	30
Removing laundry/switching the appliance off	30
1. Open the door and remove the laundry.	30
2. Press the center of the Program Selector. Appliance is switched off and dryer light goes out.	30
3. Clean lint filter. ~ Cleaning the lint filter; Page 39	30
4. Close the door.	30
Tip:	30
Home Connect ™	31
Home Connect ™	31
1. Install the Home Connect app on your mobile device.	31
2. Register in the Home Connect app.	31
3. Connect your appliance to your home network automatically or manually (you only need to do this the first time).	31
4. Connect your appliance to the Home Connect app.	31
Notes	31
Calling up the Home Connect menu	31
1. Switch the appliance on.	31
2. Press and hold Remote Start for at least 3 seconds.	31
Note:	31
Connecting to the home network and the Home Connect app	31
Notes	31
Note:	31
Connecting to your home network automatically	31
1. Press Start/Pause.	31
2. Activate the WPS function on your home network router within the next 2 minutes.	31
Note:	31
Connecting to your home network manually	32
1. Set the program to position 2.	32
2. Press Start/Pause.	32
3. Call up the Wi-Fi setting on the mobile device.	32
4. Connect the mobile device to the HomeConnect Wi-Fi network and enter the password (key) HomeConnect.	32
5. Once you have connected successfully, open the Home Connectؘ app on your mobile device and carry out the steps in the app.	32
6. In the Home Connect app, enter the network name (SSID) and password (key) for your home network.	32
7. Carry out the last steps in the Home Connect app to connect your appliance.	32
Note:	32
Connecting to the Home Connect app	32
1. Set the program to position 3.	32
2. Press Start/Pause.	32
3. Once your appliance is displayed in the app, carry out the last steps in the Home Connect app.	32
Note:	32
Activating/deactivating Wi-Fi	33
1. Set the program to position 4.	33
2. Press Start/Pause.	33
Notes	33
Resetting your network settings	33
1. Set the program to position 5.	33
2. Press Start/Pause.	33
3. Press Start/Pause.	33
Note:	33
Updating the software	33
1. Set the program to position 6.	33
2. Press Start/Pause.	33
3. Press Start/Pause.	33
Note:	33
Information on data protection	33
Note:	33
Declaration of Conformity	34
Wi-Fi® Module FCC/IC Statements	34
9 CAUTION	34
This device complies with Part 15 of the FCC Rules. Operation to the following two conditions:	34
This device complies with Industry Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions:	34
Laundry	35
Laundry	35
Preparing the laundry	35
NOTICE:	35
Therefore, note the following tips when preparing your laundry:	35
Sorting the laundry	35
Do not dry the following textiles in the dryer:	35
Drying tips	35
Program selection table	36
Program selection table	36
Tip:	36
Optional program settings	37
Optional program settings	37
Low Heat	37
Time Dry 5	37
Remote Start	37
NOTICES	37
Finish in	37
NOTICE:	37
Dryness Level	37
Level Adjust	37
NOTICE:	37
End Signal	37
Wrinkle Block™	37
Appliance settings	38
Appliance settings	38
Child lock	38
NOTICE:	38
Activating setting mode	38
1. Switch on the appliance. The indicator lamp of the program on position 1 (() lights up.	38
2. Press and hold Dryness Level button and, at the same time, turn the program selector to position 2 (0).	38
3. Release Dryness Level button.	38
You can adjust the volume of audible notification signals (that indicate that a program has ended, for example) and audible button signals by turning the program selector to the following positions:	38
1. Turn the program selector to the required position.	38
2. Use the Finish in N or M button to set the volume you require.	38
1. Turn the program selector to position 4 (@).	38
2. Use the Finish in N or M button to switch the appliance's automatic switch-off function on (‹Ÿ) or off (‹””).	38
NOTICE:	38
Exiting setting mode	38
USER-MAINTENANCE INSTRUCTIONS	39
User-maintenance instructions	39
9 WARNING	39
Risk of explosion	39
9 CAUTION	39
Cleaning the housing and control panel	39
NOTICE:	39
Cleaning the lint filter area	39
Cleaning the lint filter	39
Tip:	39
1. Press the center of the Program Selector to switch off the appliance.	39
9 CAUTION	39
2. Open the door.	39
3. Pull out filter.	39
4. Open the filter.	40
5. Remove fluff (run hand over filter).	40
NOTICE:	40
6. Close the filter and re-insert it.	40
7. Close the door.	40
Cleaning the heat exchanger	40
1. If the dryer is hot, run on 5 Air Fluff program to allow the dryer to cool down.	40
2. Residual water may escape, place an absorbent cloth under the maintenance flap.	40
3. Unlock the maintenance flap and open it completely.	40
4. Turn both locking levers towards each other.	40
5. Pull out the heat exchanger cap.	40
6. Remove the heat exchanger.	40
NOTICE:	40
7. Rinse the heat exchanger and the cap on all sides with a jet of water to completely remove all of the lint and fluff.	41
8. Remove all lint and fluff from the seals on the dryer and heat exchanger.	41
9. Allow the cap and the heat exchanger to dry fully.	41
10. First insert the heat exchanger, then the cap.	41
11. Turn back both locking levers.	41
12. Close the maintenance flap until it locks into position.	41
13. Look in the Troubleshooting table to reset the maintenance indication. ~ Troubleshooting; Page 42	41
Cleaning the moisture sensors	41
1. Open the door.	41
2. The deposit on the sensors can easily be removed by wiping the sensors (the two bars next to the lint filter) with a cloth and a little white vinegar.	41
NOTICE:	41
Maintenance of drain hose	41
NOTICE:	41
Troubleshooting	42
Troubleshooting	42
Introduction	42
NOTICE:	42
9 WARNING	42
Risk of injury to skin	42
9 WARNING	42
Risk of electric shock! Explosion hazard	42
1. Press the center of the Program Selector to switch off the appliance.	42
2. Disconnect the dryer from the power outlet.	42
3. Call Customer Service. ~ Customer service; Page 5	42
General Troubleshooting	42
NOTICE:	42
Determing the Problem	43
If troubleshooting did not solve your issue contact Customer Service ~ Customer service; Page 5	44
STATEMENT OF LIMITED PRODUCT WARRANTY	45
STATEMENT OF LIMITED PRODUCT WARRANTY	45

Match case Limit results 1 per page

en-us

Use and Care Manual, Installation Instructions

Dryer

WTG865H3UC