Boss Audio ATV30BRGB User Manual V2

FCC

COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of this device.

This transmitter must not be co-located or operated in conjunction with any other

antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by

user. This equipment complies with FCC/ IC radiation exposure limits set forth for

an uncontrolled environment and meets the FCC radio frequency (RF) Exposure

Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This

equipment has very low levels of RF energy that it deemed to comply without

maximum permissive exposure evaluation (MPE). But it is desirable that it should

be installed and operated keeping the radiator at least 20 cm or more away from

person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration

or modifications carried out without appropriate authorization may invalidate the

user’s right to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guar-

antee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

□ Relocate or reorient the receiving antenna.

□ Increase the separation between the equipment and receiver.

□ Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

□ Consult the dealer or an experienced radio/TV technician for help.

THIS PACKAGE CONTAINS

1- ATV

30

B

RGB

All Terrain Speaker System

1- Bluetooth Multi-Function Controller

1- Handlebar Mounting Kit

1- Quick Connect Power Extension Adaptor

5- Nylon Mounting Straps and Nylon Zip Tie

1- User Manual Quick Start Guide / Poster

1- Warranty Card

USER MANUAL

QUICK START GUIDE

Thank you for purchasing this

ATV

30

B

RGB

All

-

Terrain Sound System

Please read through these instructions carefully so you will know how to

operate your model properly.

After you have finished reading the instructions, keep this document in a

safe place for future reference.

INFORMATION TO THE USER

INFORMATION TO THE USER

T

he Bluetooth® word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such marks is under license.

Other trademarks and trade names are those of their respective owners.

CAUTION!!

ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

GETTING TO KNOW YOUR

ATV

30BRGB

MULTIFUNCTION CONTROLLER (MFC)

BEFORE YOU START

IMPORTANT SAFETY PRECAUTIONS

● Do not operate mobile equipment while driving a motorized vehicle – safe driving and

safety consideration of others should always be your highest priority.

● In the event you should notice smoke, strange noises or odor from this product, or any

other abnormal signs, immediately turn off the power and consult your dealer or the nearest

authorized BOSS AUDIO Service Center. Using this product in this condition may result in

permanent damage to the system.

● Set your volume control at a low setting, then slowly increase the sound until you can

hear it comfortably without distortion, or ear discomfort.

●

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

- Do not turn up the volume so high that you can’t hear what’s around you.

- Use caution or temporarily discontinue use in potentially hazardous situations.

INSTALLATION PRECAUTIONS

WARNING

- Always consult a professional installer

● Do not attempt to install or service this product by yourself. Installation or servicing of this

product by persons without professional training and experience in electronic equipment

and motorized vehicle accessories may be dangerous and could expose you to the risk of

electric shock, injury or other hazards

● Refer any repairs to a qualified BOSS AUDIO SYSTEMS Service Center

● The ATV25B can be powered from a vehicles cigarette lighter / auxiliary power port, or

hard wired directly to the battery through an optional relay / accessory switch

● When wiring directly to the vehicles battery, be sure to disconnect the batteries negative

terminal wire before starting any wiring procedures, it is suggested that an optional fuse and

fuse holder (not included) with minimum rating of 15 Amps be in line with the positive

battery terminal

● The ground cable length should not exceed 18-inches (See wiring diagram)

● The ATV25B has a weather resistant design, it should not be submerged in or under water

under any circumstances

● Use only the installation parts provided with the ATV25B

● Wash with a mild soap or detergent and lukewarm water using a clean sponge or a

soft

cloth. Rinse well with clean water.

“Don’ts” - Very Important

● DON’T clean in hot sun or on very hot days.

● DON’T use abrasive or highly alkaline cleaners on the main body

● DON’T scrape the main body with razor blades, or other sharp instruments

● DON’T ever use, gasoline, acetone or carbon tetrachloride

GETTING STARTED

A

1

2

3

4

5

A

4

5

2

1

MFC - MULTIFUNCTION CONTROLLER

PLAY/PAUSE / Press and hold for POWER ON

NEXT TRACK / Press and hold for VOL +

PREVIOUS TRACK / Press and hold for VOL -

BLUETOOTH PAIRING / Press and hold

3.5mm AUX-INPUT

CAUTION!! Using other mounting methods may void this warranty

PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION

To avoid battery exhaustion, be sure to occasionally run the

vehicles engine while using this product.

Using this product without running the engine can drain the battery.

BLUETOOTH OPERATION

BLUETOOTH OPERATION

RECONNECTION

1)

Power on the

ATV

30

B

RGB

and your last paired device

Bluetooth.

2)

The unit will now automatically reconnect

3) If your device was previously paired with the

ATV

30

B

RGB

, but it wasn’t the last paired device:

a.

Ensure no other devices are currently paired

b.

Enter the

Bluetooth Menu

on your device being paired

c.

“BOSS AUDIO ATV”

will display under

AVAILABLE

DEVICES

d.

Choose the

“ATV

30

B

RGB

”

to reconnect

4)

If the device is out of range from the

ATV

30

B

RGB

, it will disconnect automatically:

a.

To reconnect once device is back in range, press the

1

P

lay/Pause

button

b.The

ATV

30

B

RGB

will now reconnect to the device

1

4

Tips

:

MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION

1) Press the

1

once to start playing music or press the

PLAY

button from your device

touch screen

2) To skip songs or advance, press the

2

NEXT TRACK

button

3) To select the previous song, press the

3

PREVIOUS TRACK

button

VOLUME CONTROL

4) To raise the volume

Press and Hold

the

2

button 2 ~ 3 seconds

5) To lower the volume

Press and Hold

the

3


MULTIFUNCTION CONTROLLER AUX-IN OPERATION

1)

Power on the

ATV

30

B

RGB

by pressing the

1

Play/Pause

multifunction button

momentarily

2)

Connect an optional 3.5mm

AUX-IN

cable located on right side of the MFC to your devices

headphone jack

3)

Route the wire back to ATV25B, and secure your device

VOLUME CONTROL

4) To raise the volume

Press and Hold

the

2


5) To lower the volume

Press and Hold

the

3


STREAMING MUSIC

Make sure your device Bluetooth volume is set at 100% level

before stowing in to the carry pouch

AUX-INPUT

Make sure your device headphone volume is set at 100% level

before stowing in to the carry pouch

ATV

30

B

RGB

can play audio from any

device that has a 3.5mm headphone

audio jack.

YOUR DEVICE

& AUX CABLE

1

3

2

Tips

:

Tips

:

MULTI-FUNCTION CONTROLLER MOUNTING

LEFT

or

RIGHT

FOR ILLUSTRATION PURPOSES

YOUR VEHICLE MAY VARY

FOR ILLUSTRATION PURPOSES

YOUR VEHICLE MAY VARY

RUBBER

SHIM

INSERT

WASHER

LOCK NUT

ALLEN HEAD

BOLT

LOCK NUT

ALLEN HEAD

BOLT

MULTI-FUNCTION

CONTROLLER

UNIT

SNAP

BRACKET

Z-BRACKET

HANDLEBAR

CLAMP

TOOLS NEEDED:

- 12mm Socket, Wrench or Pliers

- 6mm Allen Wrench

BEFORE INSTALLING THIS PRODUCT

When replacing the fuse, be sure to only use a fuse of the rating specified on

this product. To avoid short-circuiting, cover any disconnected leads with insulating

tape. It is especially important to insulate any unused wires, which if left uncovered

may cause a short circuit. When connecting other devices to this product, refer to

the manual for the product to be connected. The black cable is ground, make sure

to connect the ground wire first. Ensure that the ground wire is properly connected

to metal parts of the vehicles body frame or direct to the battery if your vehicle

does not have a grounded chassis frame The ground wire of this units power amp

and a second powered system must be connected to the frame separately with

different screws. If the screw for the ground wire loosens or falls out, it could result

in fire or malfunction.

To avoid potential shorts in the electrical

system, be sure to disconnect the (–)

bat

tery cable before installation. Use this

unit

with a 12-Volt battery and negative

ground

-ing only. Failure to do so may

result in a

fire or malfunction.

BLUETOOTH

®

ENABLED

ALL-TERRAIN SOUND SYSTEM

USER MANUAL

QUICK START GUIDE

ATV30BRGB

USER MANUAL

ATV30BRGB

BLUETOOTH

®

ENABLED | ALL-TERRAIN SOUND SYSTEM

PRINTED IN CHINA

VER:

2

.0 EN

0

118

BOSS Audio Systems

3451 Lunar Court • Oxnard, CA 93030

www.bossaudio.com

|

800.999.1236

Tech Support: www.bossaudio.com/support/technical-support/

BLUETOOTH

SPEAKERS

AMPLIFIER

• Version: 3.0 w/ EDR

• A2DP

• Range: 33ft (10m)

• Dimensions: 6.5” / 165.1mm

• Impedance: 4Ω

• Magnet: 11oz

• Cone Type: PP CARBON + RUBBER

SURROUND

• Tweeter Size: 1”

S

OFT DOME

• Maximum Output Power: 450 Watts

• Input impedance: 10kΩ

• Frequency Response: 45Hz-25kHz

SPECIFICATIONS

WIRE DIAGRAM

15A

Fuse and fuse holder

(not included)

Chassis

ground

point

BATTERY

Mini-DIN

Connector

Fuse is located inside the power adaptor

Turn counter clockwise to open

Replace with 10A AGC Fuse type only

Normally open switch

(not included)

INSERT

OPTIONAL DIRECT BATTERY WIRING CIRCUIT

RED

BLACK

Chassis

ground

point

QUICK RELEASE

POWER ADAPTOR

(INCLUDED)

POWER ADAPTOR

10A

Ground wire

Metal frame

Recommended 12 ~ 14ga Wire

(not included)

Align arrows

GENERAL

• Operational Power: 12VDC (10-16V allowable)

• MAX Current Draw: 10A

• Replacement Fuse: 10A AGC TYPE

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

2

3

iPod / iPhone are trademarks of Apple Inc. registered in the U.S. and other countries.

BOSS Audio Systems is not affiliated with Apple Inc.

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any

means, including photocopying, recording, or other electronic or mechanical methods, without the prior written

permission of BOSS AUDIO Inc.

Copyright © 201

8

BOSS AUDIO Inc.

3

1

SPEAKER MOUNTING SUGGESTIONS

1

ATV

30

B

RGB_

UM

_

POSTER-STYLE-v

2.0

.indd

0118

1)

Power on the

ATV

30BRGB

by pressing the

Play/Pause button momentarily,

then long press the BLUETOOTH

button, it will start to quickly flash blue color,

signaling that the ATVB69LEDis now ready for Bluetooth pairing.

NOTE:

You have 2 minutes before you must restart this procedure over again.

4

1

2)

Now that the

ATV

30BRGB

i

s in pairing mode:

ANDROID users:

a.

Go into the

Settings Menu

of your device

b. Enter the

Bluetooth Menu

c.

TURN ON Bluetooth

and press

SCAN

d.


will now be displayed under

AVAILABLE DEVICES

e. If prompted, enter passcode: “

0000

”

iOS users:

a. Go into the

Settings Menu

of your

iOS

device

b. Enter the

Bluetooth Menu

c

. TURN ON Bluetooth

d.


will now be displayed

e. If prompted, enter passcode: “

0000

”

4) If

BOSS AUDIO ATV

is not seen, repeat the above steps and refresh the “

Device List”

5) You will hear a tone when the connection is successful, you are now ready to stream

music from your favorite media player to the

ATV

30BRGB

NOTE:

You have 2 minutes before you must restart this procedure over again.

28.5"

7.95"

11.58"

Boss Audio ATV30BRGB User Manual V2

Boss Audio ATV30BRGB Manual

Boss Audio ATV30BRGB manual content summary: