Boss Audio EQ600 User Manual in English

- 1 -

- 2 -

Introduction

The

EQ-600

is a Six Channel Pre-Amp Equalizer Network with which you can install various types of

multi-amplifier systems in a car. The

EQ-600

is

to be used

with

high quality power amplifiers and

speakers in a multi-amplifier system for hi-fi (high fidelity) sound reproduction.

You will be satisfied with the

EQ-600

provides maximum flexibility to configure every possible multi-

amplifier car stereo system. Before designing and installing your system, please read this manual

thoroughly so that you can

set up

the system that practically suits you. Having the

EQ-600

in the

center of your multi-amplifier

car stereo system, your car stereo system will provide you with the

ultimate in hi-fi reproduction.

Key Features

This unit is designed for 12V DC operation only.

Avoid Installing the unit where:

- It would be subject to high temperatures, such as

direct sunlight or from hot air from the heater.

- It would be exposed to rain or moisture

- It would be subject to dust or dirt

If your car

is parked in direct sunlight and there is a considerable rise in temperature inside the

car, allow the unit to cool off before operating.

If this unit is placed

too close to the car radio or any vehicle wires, an interference may occur, in

this case, separate the unit

from the car radio and power wires.

Precautions

Location and Function of Controls (outside)

Dual-bandwidth Equalization:

Car interiors vary widely in size and acoustic make-up. The addition interior design

don't make the

best location for speaker placement causing your high performance speaker system to sound not as

good as it could be. The

EQ-600

provide a

maximum equalization control for each area of the audio

spectrum. One-third octave bass equalization combined with one-half and full octave high frequency

equalization offers an ideal level control.

13 Volts Pre-Amp Line Driver:

The

EQ-600

offers a high quality line driver that takes the low output voltage of a source unit and

increases it up to 18dB (13 volts peak). This allows you to maximize the signal-to-noise of

your

system

and drive your

amplifiers to

their maximum output without clipping. No hiss, clicks,

or pops

plus maximum sound quality.

Speaker Level Inputs:

The

EQ-600

has a unique high impedance speaker level input that will interface with most head units

and let you add amplifiers and speakers to your audio system.

PFM Subsonic Filter:

This unique feature is able to fine-tune the bass response of any system. Why waste power on nasty

subsonic information when your Programmable Frequency Match (PFM) filter will help you clean things

up.

1. Inputs:

The

EQ-600

has two types of inputs, Pre-Amp and Speaker Level. These inputs should get

their

signals from

the main

head unit and should attach to either

RCA

jacks or speaker leads that are

coming out of your source unit. If your source unit has a front, rear and

subwoofer pre-amp output,

connect them to identical inputs on your

EQ-600

. If the source unit only has front and rear inputs, don't

worry about losing your bass equalization,

the

EQ-600

will automatically routes your subwoofer

equalization controls to the rear channels.

2. Input Gain Controls:

Theses knobs allow you to increase or decrease the signal level from your

source

unit to the

EQ-600

. Most aftermarket

source units

will require an increase whereas radios

installed by the automobile manufacturer will probably require you to decrease the signal level.

3. Equalization Controls:

Each of these knobs control the

audio spectrum. They can be adjusted

the

audio output to suit your personnel taste.

4. Output Level Controls:

Although

your

EQ-600

has the ability to increase your signal voltage to

13 volts

peak, your

amplifiers may not

necessarily accept that much signal. These controls allow

you

to regulate the proper amount of pre-amp signal from the

EQ-600

to

the

amplifiers.

5. Output Voltage Indicators:

These

LED's

indicate the level of signal

voltage that is

coming out of

the various outputs

of your

EQ-600

.

6. Outputs:

These

RCA

connectors should be connected to the next component after the

EQ-600

, such

as a crossover or amplifier. Do not connect any speakers directly to your

EQ-600

or to any home

appliances.

7. Power Connections:

With

this connector, you

can wire up the power, ground and remote turn-

on

from the convenience and then casually plug it in the back of your

EQ-600

.

1

2

3

4

5

6

7

Section	Page
Page 1	1
Page 2	2
Page 3	3

Boss Audio EQ600 User Manual in English

Boss Audio EQ600 Manual

Boss Audio EQ600 manual content summary: