Boss Audio NX1600.2 User Manual in English
Boss Audio NX1600.2 Manual
 |
View all Boss Audio NX1600.2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Boss Audio NX1600.2 manual content summary:
- Boss Audio NX1600.2 | User Manual in English - Page 1
NX3000.2 NX2000.2 NX1600.2 Two Channel MOSFET Car Audio Amplifiers NX3000.4 NX2500.4 NX2000.4 Four Channel MOSFET Car Audio Amplifiers NX2800.1 NX1800.1 MonoBlock MOSFET 17 4CH Power and Speaker wiring TriMode 18 Troubleshooting 19 Specifications ONYX MOSFET Amplifier User's Manual - page 1 - Boss Audio NX1600.2 | User Manual in English - Page 2
purchased the amplifier. • ONYX amplifier •High input cable with connector (2- and 4-channel models only) • Remote subwoofer level control • Four (4) mounting screws ONYX MOSFET Amplifier User's Manual - page 2 - Boss Audio NX1600.2 | User Manual in English - Page 3
have enough current to run the amplifiers into a 2 Ohm load. If you lack adequate current, your music reproduction will be distorted. ONYX MOSFET Amplifier User's Manual - page 3 - Boss Audio NX1600.2 | User Manual in English - Page 4
securely using screws. SHOCK HAZARD! Do not open the case of this product. There are dangerous voltages present within the unit. There are no user-serviceable parts within the unit. ONYX MOSFET Amplifier User's Manual - page 4 - Boss Audio NX1600.2 | User Manual in English - Page 5
16 gauge (or heavier) wire. 3. Connect an empty fuse holder within 18" (45 cm) of the car battery, and run 8 gauge in this manual. Be sure to observe proper polarity to avoid audio phase problems. 7. your input level requires it. Ignoring these instructions will result in an input overload to the - Boss Audio NX1600.2 | User Manual in English - Page 6
LEVEL CONT ROL POWER PROTECTION + SPEAKER To Audio Outputs of head unit or signal processor FUSES +1 2V GND RE M POWER CONNECTIONS ONYX MOSFET Amplifier User's Manual - page 6 - Boss Audio NX1600.2 | User Manual in English - Page 7
level inputs from your receiver to your amplifier at the same time! 2-Channel Amplifiers NX3000.2 NX2000.2 NX1600.2 Remote Subwoofer Level Control L+ L- HIGH LEVEL INPUTS GND R+ R- L INPUTS 2V-8V To Audio Outputs of head unit or signal processor ONYX MOSFET Amplifier User's Manual - page 7 - Boss Audio NX1600.2 | User Manual in English - Page 8
level inputs from your receiver to your amplifier at the same time! 4-Channel Amplifiers NX3000.4 NX2500.4 NX2000.4 To FRONT Audio Outputs of head unit or signal processor Remote Subwoofer Level Control CH 1 +1 Outputs of head unit or signal processor ONYX MOSFET Amplifier User's Manual - page 8 - Boss Audio NX1600.2 | User Manual in English - Page 9
low level inputs from your receiver to your amplifier at the same time! 2-Channel Amplifiers NX3000.2 NX2000.2 NX1600.2 Remote Subwoofer Level Control L+ R+ L+ L- HIGH LEVEL INPUTS GND R+ R- L MAX FUSES +1 2V GND RE M POWER CONNECTIONS L- R- ONYX MOSFET Amplifier User's Manual - page 9 - Boss Audio NX1600.2 | User Manual in English - Page 10
low level inputs from your receiver to your amplifier at the same time! 4-Channel Amplifiers NX3000.4 NX2500.4 NX2000.4 Remote Subwoofer Level Control CH 1 +1 +21 CH CH 12 +1 CH +1 CH INPUTS 34 GND +CH4 To Speaker Terminals of head unit ONYX MOSFET Amplifier User's Manual - page 10 - Boss Audio NX1600.2 | User Manual in English - Page 11
PROTECTION + SPEAKER FUSES +1 2V GND RE M POWER CONNECTIONS Battery FUSE to REMOTE TURN-ON terminal of head unit Chassis ground point ONYX MOSFET Amplifier User's Manual - page 11 - Boss Audio NX1600.2 | User Manual in English - Page 12
Power and Speaker Wiring 2 Channel 2-Channel Amplifiers NX3000.2 NX2000.2 NX1600.2 Two Channel Mode LEFT Speaker RIGHT Speaker SPEAKER IMPEDANCE 2-8 OHMS L+ L- HIGH LEVEL INPUTS GND R+ R- to REMOTE TURN-ON terminal of head unit Chassis ground point ONYX MOSFET Amplifier User's Manual - page 12 - Boss Audio NX1600.2 | User Manual in English - Page 13
Power and Speaker Wiring Bridged Mode 2-Channel Amplifiers NX3000.2 NX2000.2 NX1600.2 Connect the Positive (+) terminal of the subwoofer to the L (+) amplifier terminal. Connect the Negative (-) REMOTE TURN-ON terminal of head unit Chassis ground point ONYX MOSFET Amplifier User's Manual - page 13 - Boss Audio NX1600.2 | User Manual in English - Page 14
allows you to connect this amplifier to a pair of main speakers NX3000.2 NX2000.2 NX1600.2 plus a subwoofer on one pair of output channels. The main speakers will 8 OHMS Subwoofer Battery FUSE ONYX MOSFET Amplifier User's Manual - page 14 to REMOTE TURN-ON terminal of head unit Chassis ground - Boss Audio NX1600.2 | User Manual in English - Page 15
Power and Speaker Wiring 4 Channel Mode Four Channel Mode 4-Channel Amplifiers NX3000.4 NX2500.4 NX2000.4 SPEAKER IMPEDANCE 2-8 OHMS CH2 Speaker CH1 Speaker CH 1 +1 +21 CH CH 12 +1 CH +1 CH TURN-ON terminal of head unit Chassis ground point ONYX MOSFET Amplifier User's Manual - page 15 - Boss Audio NX1600.2 | User Manual in English - Page 16
the Negative (-) terminal of the RIGHT subwoofer to the CH4(-) amplifier terminal. 4-Channel Amplifiers NX3000.4 NX2500.4 NX2000.4 SPEAKER IMPEDANCE 4-8 OHMS CH 1 +1 +21 CH CH 12 +1 CH +1 CH INPUTS 34 GND of head unit Chassis ground point ONYX MOSFET Amplifier User's Manual - page 16 - Boss Audio NX1600.2 | User Manual in English - Page 17
mode operation allows you to connect this amplifier to a pair of main speakers NX3000.4 NX2500.4 NX2000.4 plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO TURN-ON terminal of head unit Chassis ground point ONYX MOSFET Amplifier User's Manual - page 17 - Boss Audio NX1600.2 | User Manual in English - Page 18
previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM POSSIBLE the Protection LED still comes on, then the amplifier is faulty and needs servicing. No output. Check that all fuses are OK. Check that amplifier Manual - page 18 - Boss Audio NX1600.2 | User Manual in English - Page 19
Specifications MODEL 2-Channel MOSFET Amplifiers NX1600.2 NX2000.2 NX3000.2 MonoBlock MOSFET Amplifiers NX1800.1 NX2800.1 RMS POWER into 4 Ohms 400W x 2 500W x 2 700W x 2 18-5/16" 23-1/2" All specifications subject to change without notice. ONYX MOSFET Amplifier User's Manual - page 19
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
 |
 |
CONTENTS
ONYX MOSFET Amplifier User’s Manual - page 1
USER’S MANUAL
2
Introduction
2
What is included?
3
Features
3
About 2 Ohm operation
4
General precautions
4
Installation precautions
4
Mounting the amplifier
5
Connecting the amplifier
6
Low level input wiring
9
High level input wiring
11
MonoBlock Power and
Speaker wiring
12
2CH Power and Speaker wiring
2CH Mode
13
2CH Power and Speaker wiring
Bridged Mode
14
2CH Power and Speaker wiring
TriMode
15
4CH Power and Speaker wiring
4CH Mode
16
4CH Power and Speaker wiring
Bridged Mode
17
4CH Power and Speaker wiring
TriMode
18
Troubleshooting
19
Specifications
page
NX3000.2
NX2000.2
NX1600.2
Two Channel
MOSFET Car Audio
Amplifiers
NX3000.4
NX2500.4
NX2000.4
Four Channel
MOSFET Car Audio
Amplifiers
Congratulations on your
purchase of a
ONYX
Amplifier.
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
Thank you for making
your choice for car audio
entertainment!
NX2800.1
NX1800.1
MonoBlock
MOSFET Car Audio
Amplifier