Canon LV-8227A User Manual
Canon LV-8227A Manual
 |
View all Canon LV-8227A manuals
Add to My Manuals
Save this manual to your list of manuals |
Canon LV-8227A manual content summary:
- Canon LV-8227A | User Manual - Page 1
MULTIMEDIA PROJECTOR User's Manual - Canon LV-8227A | User Manual - Page 2
the Wired LAN network function. You can operate and manage the projector via network. For details, refer to the user's manual of "Network Set-up and Operation." (LAN Network function is only for LV-7292A, LV-7297A, LV-7392A, LV-8227A.) ♦ Auto Setup Function This function enables Auto input, Auto - Canon LV-8227A | User Manual - Page 3
Lamp Replacement 68 Appendix 70 Troubleshooting 70 Menu Tree 73 Indicators and Projector Condition 75 Compatible Computer Specifications 76 Technical Specifications 78 Optional Parts 79 PJ Link Notice (Only for LV-7292A, LV-7297A, LV-7392A, LV-8227A) 80 Attaching the Filter Cover - Canon LV-8227A | User Manual - Page 4
again, check operations and cable connections and try the solutions in the "Troubleshooting" section on pages 70-72 of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO - Canon LV-8227A | User Manual - Page 5
service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions - Canon LV-8227A | User Manual - Page 6
cord and remove the dust that builds up on the power cord or connector. WARNING Follow the instructions below to install or handle the projector. Otherwise, a fire, an electric shock, or injury may result. - Do not touch the projector, power cord, or cables when lighting begins. - Do not use the - Canon LV-8227A | User Manual - Page 7
or power sources. - Do not place the projector on a carpet or bed. The internal temperature will rise, causing malfunction. - To avoid increase in the internal temperature, do not block the intake/exhaust vents. - Position the projector at a proper angle. Incorrect positioning may cause troubles and - Canon LV-8227A | User Manual - Page 8
in an unsuitable transport case. This may cause damage to the projector. For information about transporting the projector by courier or any other transport service, consult your dealer. - Do not put the projector in a case before the projector is cooled enough. Exhaust Vent (Hot air exhaust) 8 - Canon LV-8227A | User Manual - Page 9
Multimedia Projector, Model: LV-7292A, LV-7297A, LV-7392A, LV-8227A, LV-7292M, LV-7297M, LV instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A., Inc. One Canon the plug will fit into the power outlet. Do not try to - Canon LV-8227A | User Manual - Page 10
⑪ LAN Connection Terminal (LAN Connection Terminal is only for LV-7292A, LV-7297A, LV-7392A, LV-8227A.) Note: L AN Connection Terminal is for the Network function. Refer to the user's manual of "Network Set-up and Operation" . ⑫ Power Cord Connector Note: Replace only with the same types - Canon LV-8227A | User Manual - Page 11
⑧ ⑦⑥ ① CONTROL When the projector is controlled by a computer, HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI 's manual of "Network Set-up and Operation"). (LAN Connection Terminal is only for LV-7292A, LV-7297A, LV-7392A, LV-8227A.) - Canon LV-8227A | User Manual - Page 12
setting of Auto setup (includes Auto input, Auto PC and Auto Keystone functions) in the setting menu (pp.26, 52). ④ POWER button Turn the projector on or off (pp.21-23). ⑤ POWER indicator - Lights red when the projector is in stand-by mode. - Lights green during operations. - Blinks green in the - Canon LV-8227A | User Manual - Page 13
Part Names and Functions Remote Control Unit ① ② ③ ㉑ ④ ⑳ ⑲ ⑤ ⑥ ⑦ ⑱ ⑧ ⑰ ⑨ ⑯ ⑮ ⑩ ⑭ ⑪ ⑬ ⑫ LV-RC06 ① POWER button Turn the projector on or off. (pp.21-23) ② AUTO SET button Execute the setting of Auto setup (includes Auto input, Auto PC and Auto Keystone functions) in - Canon LV-8227A | User Manual - Page 14
used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Unit Operating Range Point the remote control unit toward the projector (Infrared Remote Receiver) when 1 and Code 2. The initial code is set to Code 1. 14 LV-RC06 MENU button IMAGE button - Canon LV-8227A | User Manual - Page 15
Installation Positioning the Projector For projector positioning, see the figures below. The projector should be set " 4064 x 3048 19.1'(5.8m) 22.9'(7.0m) 300" 6096 x 4572 28.6'(8.7m) 34.4'(10.5m) For LV-8227A, LV-8227M A:B = 13:1 Screen Size 40" (W x H) mm 16:10 aspect ratio 862 x 538 Zoom - Canon LV-8227A | User Manual - Page 16
adjustable foot is lifted too high or the project angle is too oblique to the screen. In these conditions, adjust the height of the support desk of the projector. Note: Keystone distortion of the projected image can be corrected by menu operation. (pp 26, 38, 40, 48, 50) About the brightness of - Canon LV-8227A | User Manual - Page 17
is supplied.) • Audio Cables • HDMI-DVI Cable (*One cable is supplied; other cables are not supplied with the projector.) Note: U nplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. Installation MIC Audio Output Audio cable (stereo - Canon LV-8227A | User Manual - Page 18
• VIDEO Cable • S-VIDEO Cable • S-VIDEO-VGA Cable • Audio Cables • HDMI Cable (Cables are not supplied with the projector. ) Note: Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. Video, DVD player, etc. Video, DVD player, etc - Canon LV-8227A | User Manual - Page 19
connection • Audio Cables • Scart-VGA Cable • COMPONENT Cable • COMPONENT-VGA Cable (Cables are not supplied with this projector.) Note: Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. Video, DVD player, etc. Audio Output RGB - Canon LV-8227A | User Manual - Page 20
electrical shock, do not plug into any other type of power system. If you are not sure of the type of power being supplied, consult your authorized dealer or service center. Connect the projector with all peripheral equipment before turning the projector on. CAUTION The AC outlet must be near this - Canon LV-8227A | User Manual - Page 21
And then follow the input signal guidance window to correct the signal and connection. If the projector is locked with a PIN code, PIN code input dialog box will appear. Enter the PIN code as instructed on the next page. 16 The preparation display will disappear after 30 seconds. Selected Input - Canon LV-8227A | User Manual - Page 22
code. Write down the number as a reminder. Should the PIN code be missing or forgotten, consult your dealer or service center. About the Power Management mode This projector has the Power Management mode function. When there is no signal input for more than 30 seconds and also there is no operation - Canon LV-8227A | User Manual - Page 23
stop immediately. The lamp remains high temperature and needs to be cooled. Note: • When the Direct power on function is set to On, the projector will be turned on automatically by connecting the AC power cord to an AC outlet (p.56). • The running speed of cooling fans is changed according to the - Canon LV-8227A | User Manual - Page 24
projector procedure, refer to respective sections in this manual. 1 Press the MENU button on the LAMP REPLACE VOL POWER AUTO SET POINT buttons VOL MENU OK MENU LV-RC06 When Main menu is selected Point ► or OK button When Sub menu is selected * Point ◄ button * About the guide - Canon LV-8227A | User Manual - Page 25
Used to set the projector's operating configurations. (pp.51-63) ⑧ Information Display the input source information. (p.64) ⑨ Network S ee user's manual of "Network Set-up and Operation". (Network function is only for LV-7292A, LV-7297A, LV-7392A, LV-8227A. ⑩ Guide The key operation is displayed - Canon LV-8227A | User Manual - Page 26
fully adjusted with the Auto PC Adjustment function. When the image is not provided properly with this operation, manual adjustments are required (pp.33-34). Top WCARoNINnGtrol LAMP REPLACE POWER AUTO SET AUTO SET button VOL VOL POINT ▲▼ buttons MENU OK Remote control unit AUTO SET button - Canon LV-8227A | User Manual - Page 27
Basic Operation Sound Adjustment Direct Operation POWER TopWACRNINoG ntrol Volume Press the VOLUME+/- buttons. The Mute function is also effective for the AUDIO OUT jack. Remote control unit LV-RC06 Menu Operation Volume Dialog Box VOLUME +/- buttons VOLUME + button MUTE button VOLUME - - Canon LV-8227A | User Manual - Page 28
, H-sync freq., V-sync freq., Aspect, Language, Lamp status, Lamp counter, Power management mode, Key lock, PIN code lock, Remote control and SERIAL NO. (p. buttons HDMI button COMPONENT button S-VIDEO button INFO. button LAMP button LV-RC06 Note: See the next page for the description of other - Canon LV-8227A | User Manual - Page 29
image mode of the screen. See pages 35, 44 for details. Remote control unit ASPECT button P-TIMER button BLANK button IMAGE button Note: LV-RC06 S ee the previous page for the description of other buttons. BLANK Blank disappears after 4 seconds. P-Timer ASPECT button Select the screen size - Canon LV-8227A | User Manual - Page 30
Computer Input Input Source Selection (ANALOG PC: COMPUTER) Direct Operation Choose COMPUTER (ANALOG PC) by pressing the COMPUTER button on the remote control unit. Remote control unit COMPUTER button COMPUTER (ANALOG PC) COMPUTER (SCART) Menu Operation 1 Press the MENU button to display the On- - Canon LV-8227A | User Manual - Page 31
(pp. 33-34). - - - - There is no signal input from the computer. Check the connection between your computer and the projector. (See "Troubleshooting" on p. 71.) Mode 1 The preset system is manually adjusted in the PC adjust Menu. The adjusted data can be stored in Mode 1-10 (pp. 33-34). SVGA - Canon LV-8227A | User Manual - Page 32
: • The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting a Input Menu • U se PC adjust menu to adjust the System mode manually and store the adjusted parameters in the Custom Mode. See page 34 - Canon LV-8227A | User Manual - Page 33
PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen - Canon LV-8227A | User Manual - Page 34
Computer Input Reset To reset the adjusted data, select Reset and press the OK button. A confirmation box appears and then select Yes. All adjustments will return to their previous figures. Mode free To clear the stored data, select Mode free and then press the Point ► or the OK button. Move the - Canon LV-8227A | User Manual - Page 35
desired item and then press the OK button. Presentation For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. High contrast Picture mode with improved halftone for graphics. Cinema Picture mode adjusted with fine tone. Blackboard (Green) For the image projected - Canon LV-8227A | User Manual - Page 36
* Press the Point ◄► buttons to select Off or On. Off ...... Disabled. On ...... The iris function is activated. * Auto iris is only for LV-7292A, LV-7297A, LV-7392A, LV-8227A. Color temp. Use the Point ◄► buttons to select the desired Color temp. level (XLow, Low, Mid, or High). White balance (Red - Canon LV-8227A | User Manual - Page 37
Computer Input Aspect Setting (For LV-7292A, LV-7297A, LV-7392A, LV-7292M, LV-7297M) This projector has the picture screen resize last stored aspect screen image. Custom adj. Adjust the screen scale and position manually with this function. Press the Point ► button at Custom adj. and the Custom - Canon LV-8227A | User Manual - Page 38
when the AC power cord is plugged out or turned off the projector. Reset..........Release the keystone correction when the AC power cord is plugged their previous figures. 38 Remote control unit POINT buttons OK button Keystone LV-RC06 D.ZOOM + button D.ZOOM - button Press the OK button. - Canon LV-8227A | User Manual - Page 39
Computer Input Aspect Setting (For LV-8227A, LV-8227M) This projector has the picture screen resize function, the last stored aspect screen image. Custom adj. Adjust the screen scale and position manually with this function. Press the Point ► button at Custom adj. and the Custom adjustment - Canon LV-8227A | User Manual - Page 40
power cord is plugged out or turned off the projector. Reset...........Release the keystone correction when the AC power 16:10) ....1 6:10 is the aspect of the LCD panel. The original Screen Menu is available. 16:9 unit POINT buttons OK button Keystone LV-RC06 D.ZOOM + button D.ZOOM - Canon LV-8227A | User Manual - Page 41
select Input and then press the Point ► or the OK button. 2 Use the Point ▲▼ buttons to select VIDEO and then press the OK button. VIDEO LV-RC06 VIDEO When video input signal is connected to the VIDEO jack, select VIDEO. Use the Point ▲▼ buttons to select COMPUTER. And then press the - Canon LV-8227A | User Manual - Page 42
VIDEO Input Input Source Selection (COMPONENT, SCART, HDMI) Direct Operation Choose COMPUTER (COMPONENT) or COMPUTER (SCART) by pressing the COMPONENT or the COMPUTER button on the remote control unit. Choose HDMI by pressing the HDMI button on the remote controller. Remote control unit HDMI - Canon LV-8227A | User Manual - Page 43
system, and adjusts itself to optimize its performance. When VIDEO System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL - Canon LV-8227A | User Manual - Page 44
desired item and then press the OK button. Presentation For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. High contrast Picture mode with improved halftone for graphics. Cinema Picture mode adjusted with fine tone. Blackboard (Green) For the image projected - Canon LV-8227A | User Manual - Page 45
the Point ◄► buttons to select Off or On. Off ...... Disabled. On ...... The Auto iris function is activated. * Auto iris is only for LV-7292A, LV-7297A, LV-7392A, LV-8227A. Use the Point ◄► buttons to adjust the setting value. Color temp. Use the Point ◄► buttons to select the desired Color temp - Canon LV-8227A | User Manual - Page 46
following options. Off........ Disabled. L 1........ For an active picture. L 2........ For a still picture. Film...... For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the OK - Canon LV-8227A | User Manual - Page 47
VIDEO Input Aspect Setting (For LV-7292A, LV-7297A, LV-7392A, LV-7292M, LV-7297M) This projector has the picture screen resize the last stored aspect screen image. Custom adj. Adjust the screen scale and position manually with this function. Press the Point ► button at Custom adj. and the Custom - Canon LV-8227A | User Manual - Page 48
, press the Point ► button. Store...........K eep the keystone correction even when the AC power cord is plugged out or turned off the projector. Reset..........Release the keystone correction when the AC power cord is plugged out. Ceiling When this function is set to On, the picture will - Canon LV-8227A | User Manual - Page 49
VIDEO Input Aspect Setting (For LV-8227A, LV-8227M) This projector has the picture screen resize function, which the last stored aspect screen image. Custom adj. Adjust the screen scale and position manually with this function. Press the Point ► button at Custom adj. and the Custom adjustment - Canon LV-8227A | User Manual - Page 50
the AC power cord is plugged out or turned off the projector. Reset..........Release the keystone correction when the AC power cord is or 16:9 projection screen. Default (16:10) ....1 6:10 is the aspect of the LCD panel. The original Screen Menu is available. 16:9 Set to a 16:9 projection screen - Canon LV-8227A | User Manual - Page 51
Setting Setting This projector has a Setting menu that allows you to set up the other various functions described below. 1 Press the MENU button to display the On-Screen Menu. - Canon LV-8227A | User Manual - Page 52
works under the following situation. -When turning on the projector by pressing the POWER button on the top control or the remote control unit distortion is not corrected properly by pressing the AUTO SET button, adjust manually by pressing the KEYSTONE button on the remote control unit or selecting - Canon LV-8227A | User Manual - Page 53
Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early except; ● On-Screen Menu. ● Power off? (p. 23) ● P-Timer display. (p. 29) ● No signal for Power management (p. 56) ● Please wait ... - Canon LV-8227A | User Manual - Page 54
video equipment can be captured except for 1035i and 1080i. (Only for LV-8227A, LV-8227M) • When capturing the image that has been adjusted by the Keystone function, the adjusted data is automatically reset and the projector captures an image without keystone correction. • When Logo PIN code lock - Canon LV-8227A | User Manual - Page 55
. When you reset the Logo PIN code, the PIN code and Key lock will be reset, as well. 1. Unplug the AC Power Cord from the AC outlet. 2. Hold down the OK button on the projector and connect the AC Power Cord into the outlet again. Keep holding down the OK button until the - Canon LV-8227A | User Manual - Page 56
from equipment to equipment. For details, refer to the user's manual of your Digital RGB equipment. When the black parts of the image power on When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. 56 HDMI setup Power - Canon LV-8227A | User Manual - Page 57
Standby mode This function is available when operating the projector via network. For LV-7292A, LV-7297A, LV-7392A, LV-8227A: Network.. Supply the power to the network function even after turning off the projector by pressing the POWER button on the remote control unit. Eco.......... Select Eco - Canon LV-8227A | User Manual - Page 58
Setting Closed Caption Closed Caption is a printed version of the program sound or other information displayed on the screen. If the input signal contains closed captions, you can turn on the feature and switch the channels. Press the Point ▲▼ buttons to select Off, CC1, CC2, CC3 or CC4. If the - Canon LV-8227A | User Manual - Page 59
mode can not be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized. Remote control This projector provides two different remote control codes: the factory-set initial code - Canon LV-8227A | User Manual - Page 60
where you purchased the projector or the service center. Key lock PIN code lock This function prevents the projector from being operated projector. On 2....... Enter the PIN code to operate the projector once the power cord is disconnected; as long as the AC power cord is connected, the projector - Canon LV-8227A | User Manual - Page 61
. When you reset the PIN code, the Logo PIN code and Key lock will be reset, as well. 1. Unplug the AC Power Cord from the AC outlet. 2. Hold down the OK button on the projector and connect the AC Power Cord into the outlet again. Keep holding down the OK button until the - Canon LV-8227A | User Manual - Page 62
to 2,000 meters above the sea level) where the fans have less cooling effect. On 2 F aster than On 1 mode. Select this mode when using the projector in higher altitudes (about 2,000 meters to 3,000 meters above the sea level) where the fans have lesser cooling effect. Note: The fan noise becomes - Canon LV-8227A | User Manual - Page 63
when the Display function is set to Off (p.53), during Freeze (p.28), or Blank (p.29). Warning log This function records anomalous operations while the projector is in operation and use it when diagnosing faults. Up to 10 warning logs are displayed with the latest warning message at the top of - Canon LV-8227A | User Manual - Page 64
. Aspect The selected Screen size is displayed. LV-RC06 Information Menu Language The selected language is The cumulative lamp operating time is displayed. Power management mode Off, Standby or Exit, projector is displayed. The serial number is used to service the projector. 64 INFO. button - Canon LV-8227A | User Manual - Page 65
cannot be turned on and the WARNING indicator still lights red, unplug the AC power cord and contact the service center. WARNING DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. MENU OK Top Control WARNING - Canon LV-8227A | User Manual - Page 66
arrow direction. 3 Slide the new filter (along the guide rails. Make sure that the filter is inserted completely.) Place the latch back in the LOCK position. 4 Connect the AC power cord to the projector and turn on the projector. 5 Reset the filter counter. Filter Latch CAUTION - D o not - Canon LV-8227A | User Manual - Page 67
secure it in place. 2 To pass the other end of the string into the hole on the bottom of the projector and pull at it. Cleaning the Projection Lens Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of nonabrasive camera lens - Canon LV-8227A | User Manual - Page 68
. If pieces of glass get into your eyes or mouth, seek medical advice immediately. Follow these steps to replace the lamp. 1 Unplug the AC power cord. Let the projector cool for at least one hour. 2 Loosen the screw and open the lamp cover. 3 Loosen the three (3) screws that secure the lamp. Lift - Canon LV-8227A | User Manual - Page 69
projector : LV-7292A, LV-7297A, LV-7392A, LV-8227A, LV-7292M, LV-7297M, LV-8227M ● Replacement Lamp Type No.: LV-LP35 CAUTION LAMP HANDLING PRECAUTIONS This projector the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) - Canon LV-8227A | User Manual - Page 70
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. - Make sure you have properly connected the projector to peripheral equipment as described on pages 17-19. - Make sure all equipment is connected to AC outlet and the power is - Canon LV-8227A | User Manual - Page 71
the setting for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 30 seconds power. settings can not be stored if not registered with Store. See pages 36,46. Power management mode does not work. - Power management - Canon LV-8227A | User Manual - Page 72
power cord and contact the dealer where you purchased the appears on the screen projector or the service center. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact - Canon LV-8227A | User Manual - Page 73
PC On/Off Auto keystone Auto Manual Off Blue/User/Black Off / Sound HDMI/COMPUTER Power management mode Direct power on On/ Code 2 Security Key lock Off Projector Remote control PIN code lock Off/ LV-7292A, LV-7297A, LV-7392A, LV-8227A. *2 Serial is only for LV-7292M, LV-7297M, LV-8227M. 73 - Canon LV-8227A | User Manual - Page 74
63 0-63 0-15 User 4 * Auto iris is only for LV-7292A, LV-7297A, LV-7392A, LV-8227A. Gamma Reset Store 0-15 Yes/No User 1 For LV-7292A, LV-7297A, LV-7392A, LV-7292M, LV-7297M User 4 Aspect Normal For LV-7292A, LV-7297A, LV-7392A, LV-7292M, LV-7297M Full 16:9 Zoom Custom Custom adj. Keystone - Canon LV-8227A | User Manual - Page 75
and cannot be turned on. Unplug the AC power cord and plug it again to turn on the projector. If the projector is turned off again, unplug the AC power cord and contact the dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or - Canon LV-8227A | User Manual - Page 76
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock. When selecting these modes, PC - Canon LV-8227A | User Manual - Page 77
of your PC may not be projected correctly. In such a case, confirm your PC settings. • When you project a DVI signal, connect the cables, turn the projector on, then select the input. Finally, turn on your PC. Be sure to follow this procedure, otherwise an image may not be projected on the - Canon LV-8227A | User Manual - Page 78
Foot Adjustment Multi-media Projector 13.13" x 3.98" x 9.72" (333.5mm x 101.0mm x 247.0mm) (Not including protrusions) LV-7292A, LV-7297A, LV-7392A, LV-8227A : 6.6 lbs (2.99 kg) LV-7292M, LV-7297M, LV-8227M : 6.4 lbs (2.9 kg) 0˚ to 10˚ Panel Resolution LCD Panel System Panel Resolution Number - Canon LV-8227A | User Manual - Page 79
LV-7292A, LV-7297A, LV-7392A, LV-8227A. Accessories User's Manual (CD-ROM) Important Information and Quick Start Guide Warranty card AC Power Cord (0.01% or less) may be ineffective by the characteristics of the LCD panels. Optional Parts The parts listed below are optionally available. When - Canon LV-8227A | User Manual - Page 80
LV-7292A, LV-7297A, LV-7392A, LV-8227A) This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). This projector supports Attach the projector to the ceiling mount in accordance with the instruction manuals which come - Canon LV-8227A | User Manual - Page 81
Red/Cr/S-C Input 9 +5V Power 2 Green/Y/S-Y Input 10 Ground ( Power 9 TMDS Data 0- Input 19 Plug insert detection 10 TMDS Clock+ Input CONTROL CONNECTOR (D-sub 9 pin) Serial 5 SG 1 ----- 6 ----2 R X D 7 ----3 T X D 8 ----4 ----- 9 ----- LAN TERMINAL (For LV-7292A, LV-7297A, LV-7392A, LV-8227A - Canon LV-8227A | User Manual - Page 82
Appendix PIN Code Protection While the projector is locked with the PIN code. Put the label below (supplied) on in a prominent place of the projector's body while it is locked with a PIN code. 82 - Canon LV-8227A | User Manual - Page 83
Dimensions Appendix Unit: mm(inch) Screw Holes for Ceiling Mount Screw: M4 Depth: 12.0(0.47) 4.6(0.18) 80.2(3.16) 247.0(9.72) 138.0(5.43) 122.2(4.81) 114.0(4.49) 2.9(0.11) 105.6(4.16) 24.0(0.94) 5.6(0.22) 195.5(7.70) 70.5(2.78) 71.7(2.82) 24.5(0.96) 137.3(5.41) 71.5(2.81) 322.1(12.68) 333 - Canon LV-8227A | User Manual - Page 84
Lake Success, NY 11042-1198, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Cote-de-Liesse, Montreal Quebec H4T 1V7, Canada
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
 |
 |
MULTIMEDIA PROJECTOR
User’s Manual