Canon LV-WX300ST User Manual

Canon LV-WX300ST Manual

Get Canon LV-WX300ST PDF manuals and user guides View all Canon LV-WX300ST manuals
Add to My Manuals
Save this manual to your list of manuals

Canon LV-WX300ST manual content summary:

  • Canon LV-WX300ST | User Manual - Page 1
    ENGLISH MULTIMEDIA PROJECTOR LV-WX300ST/LV-X300ST User's Manual
  • Canon LV-WX300ST | User Manual - Page 2
    through a web browser (e-Control 47 Controlling the projector using PJLink™ application 49 Menu operation 52 Maintenance 59 Care of the projector 59 Lamp information 60 Indicators 65 Troubleshooting 66 Specifications 67 Projector specifications 67 Dimensions 69 Timing chart 70 Control
  • Canon LV-WX300ST | User Manual - Page 3
    accidents. If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in the user's manual. If the problem still persists, contact the Canon Customer Support Center. CAUTION RISK
  • Canon LV-WX300ST | User Manual - Page 4
    SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY BECOME DETERIORATED. READ AND KEEP THIS MANUAL FOR LATER USE. All the safety and operating instructions should be read before beginning to operate the product. Read all of the
  • Canon LV-WX300ST | User Manual - Page 5
    service personnel under the following conditions: a When the power cord or plug is damaged or frayed. b If liquid has been spilled into the projector. c If the projector has been exposed to rain or water. d If the projector does not operate normally after following the operating instructions
  • Canon LV-WX300ST | User Manual - Page 6
    Power Cord Requirement The AC Power Cord supplied with this projector meets the requirements for use in the country you , waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www.canon-europe.com/battery. For CA, USA only Included lithium
  • Canon LV-WX300ST | User Manual - Page 7
    ENGLISH Federal Communication Commission Notice Multimedia Projector, Model: LV-WX300ST / LV-X300ST This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
  • Canon LV-WX300ST | User Manual - Page 8
    or bundled. • Do not use a damaged power cord. If your power cord is damaged, contact the Canon Customer Support Center. • Do not use any power cord other than the type that is included with this projector. • Be sure to connect the ground wire of the power cord to ground. Failure to do so
  • Canon LV-WX300ST | User Manual - Page 9
    parts that are hot. These could cause an electric shock or burn. If inspection, maintenance or repair is required, contact the Canon Customer Support Center. • Do not disassemble or modify the projector (including consumable parts) or the remote control. • Do not insert any object into vents in the
  • Canon LV-WX300ST | User Manual - Page 10
    cause a fire or malfunction. It is recommended that periodic maintenance of the projector be performed. For details of maintenance costs, contact the Canon Customer Support Center. Precautions on the lamp This projector uses a high-pressure mercury lamp, which must be handled carefully and correctly
  • Canon LV-WX300ST | User Manual - Page 11
    to cool down sufficiently. Failure to do so could result in a burn or personal injury due to heat from the lamp or projector. • When an instruction to replace the lamp has been displayed (LAMP Indicator Displays (See "Timing of replacing the lamp" on page 61 for details)), the possibility of
  • Canon LV-WX300ST | User Manual - Page 12
    the adjustable feet. • Attach the lens cap to protect the lens. Pay attention to the following points when installing or using the projector. • Be sure to install the projector in a location where the air intake and exhaust vents are separated from the wall by more than 50 cm (1.6'). Failure to do
  • Canon LV-WX300ST | User Manual - Page 13
    ENGLISH Contents of package Projector (US) (EU) (China) Power cord 1.8 m (70.8") Computer cable 1.8 m (70.8") (5K.1VC09.501) CD & QSG Important Information Warranty card Remote control (type number: LV-RC08) Battery (type number: CR2025) 13
  • Canon LV-WX300ST | User Manual - Page 14
    panel (See "Projector" on page 15 for details.) 2. Lamp cover 3. Vent (heated air exhaust) 5 4. Quick-release button 5. Focus ring 6. Front IR remote sensor 7. Projection lens 8 8. Vent (air intake) 6 9. Lens cap 7 Rear/lower side 10 11 12 18 19 20 9 13 14 15 16 17 21 22 10. SERVICE port 11
  • Canon LV-WX300ST | User Manual - Page 15
    the lamp. Lights up or 12 flashes when the lamp has developed a problem. 10 See "Indicators" on page 65 for details. 9. AUTO PC 1. / Down) 2. POWER indicator light Manually corrects distorted images resulting from Lights up or flashes when the projector is under operation. See "Indicators"
  • Canon LV-WX300ST | User Manual - Page 16
    Remote control: LV-RC08 7. MUTE 9. Keystone/Arrow keys ( / Up, / Down) 5 9 Manually corrects distorted images resulting from 6 14 an angled projection. See " Toggles the projector between standby mode and on. See "Starting up the projector" on page 28 and "Shutting down the projector" on page
  • Canon LV-WX300ST | User Manual - Page 17
    are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam. • You may not be able replaced by an incorrect type. • Dispose of used batteries according to the instructions. • Use of a battery of wrong type may cause explosion. Use Lithium
  • Canon LV-WX300ST | User Manual - Page 18
    USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Third party software support Canon Inc., Canon's affiliated companies, as well as sales companies do not offer any support services for these programs. We are unable to respond to questions or inquiries from you or any other
  • Canon LV-WX300ST | User Manual - Page 19
    any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location. • When the projector is mounted on the ceiling, images may appear darker than those projected in the case of tabletop mounting. This isn't a product malfunction. 19
  • Canon LV-WX300ST | User Manual - Page 20
    factors in the projected image size. 4:3 is the native aspect ratio of LV-X300ST. To be able to project a complete 16:9 (widescreen) aspect ratio image, the projector can resize and scale a widescreen image to the projector's native aspect width. This will result in a proportionally smaller height
  • Canon LV-WX300ST | User Manual - Page 21
    note of the "Hd" value. This will determine the final placement of the screen in relation to the horizontal plane of the projector. LV-X300ST: If your measured projection distance was 1 m and your screen aspect ratio is 4:3, the closest match in the "Distance from the screen: L" column
  • Canon LV-WX300ST | User Manual - Page 22
    projector. Front projection W A B H Hd A=B L LV-X300ST 20.6 9.0 22.9 10.8 27.4 LV-WX300ST (16:10) Diagonal Size inch m 60 Canon recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector
  • Canon LV-WX300ST | User Manual - Page 23
    (option) Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled
  • Canon LV-WX300ST | User Manual - Page 24
    of matching terminals on both the projector and the Video source device as described below: HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible as follows. EXPAND or ENHANCED -> NORMAL • See the User's Manual of your DVD player for details. 24
  • Canon LV-WX300ST | User Manual - Page 25
    can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take an S-Video cable and connect one end to the S-Video output terminal of the Video source device. 2. Connect the
  • Canon LV-WX300ST | User Manual - Page 26
    continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. Take a Video cable and connect one end to the composite Video output terminal of the Video source device. 2. Connect
  • Canon LV-WX300ST | User Manual - Page 27
    diagram: Video cable (option) Audio cable (option) Speakers Audio cable (option) AV device • If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also
  • Canon LV-WX300ST | User Manual - Page 28
    safety in case of trouble with the projector, use an electrical outlet having an earth leakage breaker to supply the power to the projector. If you do malfunction. 4. If the projector is activated for the first time, select your OSD language following the on-screen instructions. 5. If you are
  • Canon LV-WX300ST | User Manual - Page 29
    Power Off Panel Key Lock Sleep Timer Splash Screen OK Front Table 20 min Disable Off Disable Canon Analog RGB MENU Exit 4. Press / / / to select a preferred language and press OK/IMAGE. 5. Press MENU on the projector or remote control to leave and save the settings. Analog RGB MENU Exit 29
  • Canon LV-WX300ST | User Manual - Page 30
    necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall. Setting a password Once a password has been set, the projector cannot be used unless the correct password is entered every time the projector is started. 1. Open the OSD menu and go to
  • Canon LV-WX300ST | User Manual - Page 31
    as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is You will not have to enter the password next time you turn on the projector. • If the password is incorrect, the password error message is displayed lasting
  • Canon LV-WX300ST | User Manual - Page 32
    projector) if you want the projector to automatically search for the signals. You can also manually cycle through the available input signals. 1. Press INPUT on the projector The native display resolution of this projector is in a 4:3 (LVX300ST)/16:10 (LV-WX300ST) aspect ratio. For best display
  • Canon LV-WX300ST | User Manual - Page 33
    comes from. Auto-adjusting the image In some cases, you may need to optimize the picture quality. To do this, press AUTO PC on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will readjust the values of Frequency and Clock to provide the best
  • Canon LV-WX300ST | User Manual - Page 34
    image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control Press / on the
  • Canon LV-WX300ST | User Manual - Page 35
    in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio
  • Canon LV-WX300ST | User Manual - Page 36
    areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. LV-X300ST LV-WX300ST 1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width or its vertical height. This is suitable when you want to make
  • Canon LV-WX300ST | User Manual - Page 37
    one of the following steps. • Press OK/IMAGE on the remote control or projector repeatedly until your desired mode is selected. • Go to the PICTURE > Image sRGB mode: Suitable for projecting photos from a digital camera that supports sRGB. Compatible with the sRGB standard. 4. Movie mode: Suitable
  • Canon LV-WX300ST | User Manual - Page 38
    vibrant colors in picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors. If you prefer images with that quality, select On. If you don't need it, select Off. On is
  • Canon LV-WX300ST | User Manual - Page 39
    ENGLISH To adjust the settings: 1. Go to the PICTURE menu and highlight 6-axis Color Adjust. 2. Press OK/IMAGE and the 6-axis Color Adjust page is displayed. 3. Highlight Select Color and press / to select a color from among Red, Green, Blue, Cyan, Magenta, or Yellow. 4. Press to highlight Hue
  • Canon LV-WX300ST | User Manual - Page 40
    timer is off, pressing this key displays a confirmation message. You can decide whether to activate the timer or not by following the on-screen instruction. • If the timer is already on, pressing this key displays a confirmation message. You can decide whether to restart, continue or turn off the
  • Canon LV-WX300ST | User Manual - Page 41
    the image. The word 'FREEZE' will be displayed in the upper left corner of the screen. To release the function, press any key on the projector or remote control. Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected
  • Canon LV-WX300ST | User Manual - Page 42
    light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector. 3. Once the cooling process finishes, the POWER indicator light is a steady orange and fans stop. 4. Disconnect the power cord from the wall socket
  • Canon LV-WX300ST | User Manual - Page 43
    without closing the menu, the setting data of the menu may not be saved. 4. If you shut down the projector while controlling the projector using the network function, the application software such as e-Control™ may fail. In this case, close the application software first. After the connection
  • Canon LV-WX300ST | User Manual - Page 44
    Watching 3D content This projector supports 3D content display using the DLP Link system. This projector supports 3D image signals in Frame Sequential/Frame Packing/Top-Bottom/Side-By-Side format. You need the following items to project and watch 3D content. •
  • Canon LV-WX300ST | User Manual - Page 45
    ENGLISH • Children viewing 3D content should always be accompanied by an adult. Children may not tell you if they are feeling unwell when viewing 3D content, so always be sure to check with the child. The minimum recommended age for viewing 3D content is six years old. • Make sure you are at an
  • Canon LV-WX300ST | User Manual - Page 46
    computer using a web browser or PJLink™ application when the computer and the projector are connected to the same local area network. This projector supports Crestron® software and PJLink™. An example of connecting the projector to computer. External hub Computer LAN cable (option) (100BASE-TX or
  • Canon LV-WX300ST | User Manual - Page 47
    Remote control: LV-RC08" on page 16 for details. ii. To switch input source, click on your desired source. When you use the projector control panel System, please refer to the user manual of Crestron Control system for setup information. ii. You can name the projector, keep track of its location and
  • Canon LV-WX300ST | User Manual - Page 48
    to go back to the remote network operation page. • After making the adjustments, press the Send button and the data will be saved in the projector. • Once the password is set, the Log Out button will display beside the Tools button. • Write down your selected password in advance or right after
  • Canon LV-WX300ST | User Manual - Page 49
    Japan Business Machine and Information System Industries Association (JBMIA). (http://pjlink.jbmia.or.jp/english) • This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by PJLink™ Class 1, and the compliance has been verified with the
  • Canon LV-WX300ST | User Manual - Page 50
    PJLink™ supported commands The table below shows commands to control the projector using the PJLink™ protocol. Commend 21 22 31" The command responds with the projector name specified in the Tools page. "Canon" is returned. "LV-X300ST" or "LV-WX300ST" is returned. DMD resolution is returned. "1"
  • Canon LV-WX300ST | User Manual - Page 51
    the power is turned on. • Use 1 computer to control/monitor 1 projector. • For how to control/monitor using PJLink™, see the operation manual of the PJLink™ application you use. • When you monitor the projector's operating state using this function by issuing inquiry commands successively, issue an
  • Canon LV-WX300ST | User Manual - Page 52
    * Indicates an item that is factory-set (after reset). Options Off*/Light Yellow/Pink/Light Green/Blue/Blackboard Auto*/Real/16:10 (LV-WX300ST)/ 4:3/16:9 Auto*/Frame Sequential/ Frame Packing/Top-Bottom/ Side-By-Side Normal*/Invert Presentation/Standard*/sRGB/ Movie/User 1/User 2 On*/Off High
  • Canon LV-WX300ST | User Manual - Page 53
    */5 min/10 min/15 min/ 20 min/25 min/30 min Off*/On Disable*/30 min/1 hr/2 hr/3 hr/4 hr/ 8 hr/12 hr Black/Blue/Canon* On/Off* On/Off* On/Off* 5 sec/10 sec/15 sec*/20 sec/ 25 sec/30 sec Center*/Top-Left/Top-Right/ Bottom-Right/Bottom
  • Canon LV-WX300ST | User Manual - Page 54
    On/Off* CC1*/CC2/CC3/CC4 Standby LAN Off*/On PJLink Certification Off*/On Change PJLink Password LAN Settings DHCP On*/Off Projector IP Address Subnet Mask Default Gateway DNS Server Apply Reset All Settings Input Image Mode Current System Status Color Format Resolution Lamp
  • Canon LV-WX300ST | User Manual - Page 55
    or reduces the projected image. See "Magnifying and searching for details" on page 35 for details. This projector features a 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more the inversion of the image depth, enable this function to correct the problem. 55
  • Canon LV-WX300ST | User Manual - Page 56
    Color Tint Sharpness BrilliantColor™ Color Temperature 6-axis Color Adjust Auto Search DESCRIPTION Pre-defined image modes are provided so you can optimize your projector image set-up to suit your program type. See "Selecting a image mode" on page 37 for details. Adjusts the brightness of the image
  • Canon LV-WX300ST | User Manual - Page 57
    , it may not be turned on successfully and will rerun its cooling fans. See "Adjusting the sound" on page 42 for details. See "Personalizing the projector menu display" on page 42 for details. Lamp Mode See "Setting Lamp Mode as Economic" on page 60 for details. Reset Lamp Time See "Resetting
  • Canon LV-WX300ST | User Manual - Page 58
    dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings). When the projector displays OSD or any dialog, captions are not displayed at the same time. Caption Channel Selects a preferred closed captioning mode. To view captions
  • Canon LV-WX300ST | User Manual - Page 59
    ENGLISH Maintenance Care of the projector Your projector needs maintenance from time to time, depending on the environmental circumstances, and should be done by authorized service technicians only. Contact your dealer for instructions. The only thing you can do yourselves on a regular basis is to
  • Canon LV-WX300ST | User Manual - Page 60
    the projected images may flicker. • If this mode is frequently switched, the lamp may be deteriorated. Setting Auto Power Off This function allows the projector to turn off automatically if no input source is detected and no operation is made by user after a set period of time to prevent unnecessary
  • Canon LV-WX300ST | User Manual - Page 61
    cause a malfunction in the projector and in some instances the power off and let the projector cool for 45 minutes. If the projector is normally run with Economic to operate the projector until the 3950 the inconvenience when the projector runs out of lamp time before the projector will operate normally.
  • Canon LV-WX300ST | User Manual - Page 62
    LV-LP38 (LV-X300ST)/LV-LP40 (LV-WX300ST) • Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. • To reduce the risk of electrical shock, always turn the projector . When the instruction of lamp replacement
  • Canon LV-WX300ST | User Manual - Page 63
    the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 7. As
  • Canon LV-WX300ST | User Manual - Page 64
    secure the lamp cover. • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screws. 13. Restart the projector. Do not turn the power on with the lamp cover removed. Resetting the lamp timer 14. After the startup logo, open the On-Screen Display
  • Canon LV-WX300ST | User Manual - Page 65
    ENGLISH Indicators Light POWER TEMP Power events Orange Off Green Flashing Off Green Off Orange Flashing Off Red Off Green Off Red Flashing Off Lamp events Off Off Off Off Thermal events Red Red Red Green Red Red Flashing Green Red LAMP Off Off Off Off Off Red Off Red Red
  • Canon LV-WX300ST | User Manual - Page 66
    Troubleshooting The projector does not turn on Cause Remedy There is no power from the power cable. Attempting to turn the projector on again during the cooling process. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet
  • Canon LV-WX300ST | User Manual - Page 67
    ENGLISH Specifications Projector specifications All specifications are subject to change without notice. Model name Display system Optical system Type Size / Aspect ratio Drive system Number dots / Total number dots LV-WX300ST LV-X300ST 1-CHIP DLP™ Time division color extraction, sequential
  • Canon LV-WX300ST | User Manual - Page 68
    PC / COMPONENT terminal LV-WX300ST LV-X300ST Digital PC, digital video input Analog PC, Component (mini D-sub 15-pin) Input terminal Mini-DIN4 S video input RCA terminal Video input LAN terminal Network connection (100BASE-TX / 10BASE-T) USB Port Service port CONTROL terminal RS
  • Canon LV-WX300ST | User Manual - Page 69
    ENGLISH Dimensions 282 mm (W) x 117.9 mm (H) x 267.5 mm (D) / 11.1 in (W) x 4.6 in (H) x 10.5 in (D) (including the protrusion) 267.5 mm (10.5") 117.9 mm (4.6") 282 mm (11.1") 91 mm (3.6") Tolerance:±2 mm (0.08 in) 69
  • Canon LV-WX300ST | User Manual - Page 70
    Timing chart Supported timing for PC input Resolution 720 x 400 640 x 480 800 x 600 1024 x 85.500 108.000 *Supported timing for 3D signal in Frame Sequential, Top-Bottom and Side-By-Side formats. **Supported timing for 3D signal in Frame Sequential format. ***Supported timing for 3D signal in
  • Canon LV-WX300ST | User Manual - Page 71
    timing for HDMI (HDCP) input Supported PC timings Resolution 720 x 400 640 x 480 800 x 600 1024 x .500 108.000 *Supported timing for 3D signal in Frame Sequential, Top-Bottom and Side-By-Side formats. **Supported timing for 3D signal in Frame Sequential format. ***Supported timing for 3D signal
  • Canon LV-WX300ST | User Manual - Page 72
    .25 50 148.5 1080/60P 1920 x 1080 67.5 60 148.5 Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration. Supported timing for Video and S-Video inputs Video mode NTSC PAL SECAM PAL-M PAL-N PAL-60 NTSC4.43 Horizontal Frequency (kHz) 15.73 15.63 15
  • Canon LV-WX300ST | User Manual - Page 73
    ENGLISH Control Commands You can control this projector by sending commands via CONTROL port or LAN port. System Requirement CONTROL port Connection Cable Communication Mode Baud Rate Character Length Parity Check Stop Bits
  • Canon LV-WX300ST | User Manual - Page 74
    W W W Image Mode W W W R W W W Aspect W W R W W Image W Flip H/V W R W Auto Search W R R W Lamp W R Presentation Standard sRGB Movie User1 User2 Image Mode Aspect 4:3 Aspect 16:9 Aspect Auto Aspect Real Aspect 16:10 Aspect Status Front Table Rear Table Front Ceiling Rear
  • Canon LV-WX300ST | User Manual - Page 75
    Response Read/ Write Condition W Success Illegal format : Don't W exist command or structure Unsupported item: W this command parameter can't support W Block item: Current state can't use. R Success Response Example i:OK e:0002 INVALID_COMMAND < BLANK=ON > i:OK
  • Canon LV-WX300ST | User Manual - Page 76
    R Unsupported item: this command parameter can't support e:000A INVALID_PARAMETER < GET=INVALID > e:000A INVALID_PARAMETER • If the projector didn't receive to finish a command within 5 seconds, it will timeout and you need to resend the command. • No case sensitive. 76
  • Canon LV-WX300ST | User Manual - Page 77
    , Melville, New York 11747, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
ENGLISH
MULTIMEDIA PROJECTOR
LV-WX300ST/LV-X300ST
User’s Manual