Canon LV-X420 User Manual
Canon LV-X420 Manual
 |
View all Canon LV-X420 manuals
Add to My Manuals
Save this manual to your list of manuals |
Canon LV-X420 manual content summary:
- Canon LV-X420 | User Manual - Page 1
MULTIMEDIA PROJECTOR User's Manual #&'03&64*/( #&463&503&"%5)*464&34."/6"- 3FBEUIFl4BGFUZ*OTUSVDUJPOTzJOUIJTNBOVBMUIPSPVHIMZBOEVTFDPS SFDUMZUIFQSPKFDUPS 4UPSFUIJTVTFSTNBOVBMJOBDPOWFOJFOUMPDBUJPOXIFSFZPVDBOSFGFS UPJUFBTJMZ - Canon LV-X420 | User Manual - Page 2
...61 REPLACING THE PROJECTION LAMP ...61 Resetting the Lamp Hour ...64 CLEANING THE PROJECTOR ...65 Cleaning the Lens...65 Cleaning the Case ...65 USING THE KENSINGTON LOCK...66 Using the Kensington Lock...66 Using the Security Bar...66 TROUBLESHOOTING ...67 COMMON PROBLEMS AND SOLUTIONS ...67 TIPS - Canon LV-X420 | User Manual - Page 3
SPECIFICATIONS ...71 PROJECTION DISTANCE VS. PROJECTION SIZE ...73 Projection Distance and Size Table ...73 TIMING MODE TABLE ...75 PROJECTOR DIMENSIONS ...77 REGULATORY COMPLIANCE ...78 FCC WARNING ...78 CANADA ...78 SAFETY CERTIFICATIONS ...78 APPENDIX I...79 RS-232 PROTOCOL...79 - ii - - Canon LV-X420 | User Manual - Page 4
accidents. If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in the user's manual. If the problem still persists, contact the Canon Customer Support Center. THIS SYMBOL - Canon LV-X420 | User Manual - Page 5
SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY BECOME DETERIORATED. READ AND KEEP THIS MANUAL FOR LATER USE. All the safety and operating instructions should be read before beginning to operate the product. Read all of the - Canon LV-X420 | User Manual - Page 6
service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally after following the operating instructions - Canon LV-X420 | User Manual - Page 7
Cord supplied with this projector meets the requirements for EQUIPMENT AND EASILY ACCESSIBLE. For the U.S. and Canada, LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED or your household waste disposal service or visit www.canon-europe.com/weee, or www.canon-europe.com/battery. For - Canon LV-X420 | User Manual - Page 8
Projector, Model: LV-HD420 / LV has been tested and found instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Park, Melville, New York 11747, U.S.A. Tel No. (1) 631-330-5000 Safety Symbols in this Manual - Canon LV-X420 | User Manual - Page 9
mounting. • Do not remove the cabinet from the projector or disassemble it. The interior of the projector contains high-voltage components as well as parts that are hot. If inspection, maintenance or repair is required, contact the Canon Customer Support Center. • Do not disassemble or modify the - Canon LV-X420 | User Manual - Page 10
a fire, electric shock or personal injury. • Do not look directly into the exhaust vents during use. • Do not insert any object into vents in the projector, such as the air intake vent or exhaust vents. • Do not place a pressurized can in front of the exhaust vents. The pressure of the contents - Canon LV-X420 | User Manual - Page 11
replacement yourself. Request replacement from an installer or Canon Customer Support Center. • With ceiling-mounted projectors, the lamp may fall out when you open the lamp cover, or during replacement. During replacement, stand to the side of the lamp cover, not directly under it. Precautions for - Canon LV-X420 | User Manual - Page 12
are more likely to rupture once the lamp replacement message has been displayed. Replace the lamp with a new one as soon as possible. • Before removing the lamp, wait at least 45 minutes after turning off the projector and confirm that the lamp and projector have cooled down sufficiently. Failure to - Canon LV-X420 | User Manual - Page 13
bare hands. Doing so may result in deterioration of image quality. Take the following precautions when installing or using the projector. • Be careful of condensation. If the projector is abruptly taken to a warmer location, or if the room temperature rises abruptly, moisture in the air may condense - Canon LV-X420 | User Manual - Page 14
in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically, and may lead to other unpredictable damages. 151°5° -1-51°5° Allow - Canon LV-X420 | User Manual - Page 15
. Ensure Network Security Take measures to ensure network security. Note that Canon is not liable in any way for direct or indirect loss from access. Before using the projector, configure the appropriate projector, computer, and network security settings. Install the projector in a network protected - Canon LV-X420 | User Manual - Page 16
check that the following items are included: PROJECTOR REMOTE CONTROL (WITH ONE CR2025 BATTERY) RGB CABLE(1.8 M / 5.9') (MINI D-SUB 15-PIN / MINI D-SUB 15-PIN) (P/N: 3081409201) POWER CORD (1.8 M / 5.9') Warranty Card CD-ROM (THIS USER'S MANUAL) IMPORTANT INFORMATION WARRANTY CARD - 13 - - Canon LV-X420 | User Manual - Page 17
Views of Projector Parts Front-right View Exhaust vent Air intake vent ITEM 1. 2. 3. 4. 5. 6. LABEL Lamp Cover IR receiver Projection Lens Focus ring Zoom ring Function keys DESCRIPTION Remove to change the lamp. Receive IR signal from remote control. Focuses the projected image. Enlarges the - Canon LV-X420 | User Manual - Page 18
image size, position, and resolution Navigates and changes settings in the OSD Quick Menu - For Keystone Enter the lamp mode menu Enter or confirm highlighted OSD menu item Turns the projector On or Off. Navigates and changes settings in the OSD 29 Quick Menu - For Keystone Opens and exits - Canon LV-X420 | User Manual - Page 19
the HDMI cable from a HDMI device. (*) Connect the MHL cable from a MHL-compatible device. Note: • A dedicated adapter is required if your projector does not support the standard MHL cable. • Use a MHL cable (available on the market) and MHL-HDMI conversion adapter (available on the market) that - Canon LV-X420 | User Manual - Page 20
Lock system 66 Receive IR signal from remote control. Connect RS-232 serial port cable to control the projector with control commands Connect the USB cable from a computer (For service only) Connect an AUDIO cable to audio amplifier Connect the Microphone for use Connect the S-VIDEO cable - Canon LV-X420 | User Manual - Page 21
55mm [2.2"] 126mm [5"] 145mm [5.7"] 1 3 21 155mm [6.1"] 31mm [1.2"] ITEM 1. 2. 3. LABEL Ceiling support holes Adjustable feet Fixed foot DESCRIPTION SEE PAGE Contact your dealer for information on mounting the projector on a ceiling Rotate adjuster lever to adjust angle position. 26 - 18 - Canon LV-X420 | User Manual - Page 22
on the remote control are inoperative when you attempt to operate the projector, replace the batteries with new ones. Do not drop the remote control /OFF EXIT ASPECT RATIO SOURCE CONTRAST PC DESCRIPTION SEE PAGE Turns the projector On or Off. 29 Goes back to previous OSD menu, exits and - Canon LV-X420 | User Manual - Page 23
25. LABEL BLANK HDMI VIDEO MUTE VOLUME KEYSTONE STATUS 3D ZOOM FREEZE BRIGHTNESS LAMP MENU AUTO DESCRIPTION SEE PAGE Toggles the screen between blank and normal. Also, the infrared remote receiver on the front or rear of the projector to operate it. Remote control range is up to approximately 5 - Canon LV-X420 | User Manual - Page 24
Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A). Pull out the cover (B).. SETUP AND OPERATION 2. Insert the battery with the positive side facing up. 3. Replace the cover. Warning: Pay attention to the - Canon LV-X420 | User Manual - Page 25
. The projector splash screen displays and connected devices are detected. See Setting an Access Password (Security Lock) on page 24 if security lock is enabled. 4. If more than one input device is connected, press the SOURCE button and use ▲▼ to scroll among devices. (Component is supported through - Canon LV-X420 | User Manual - Page 26
Do not unplug the power cord until the POWER LED stops flashing-indicating the projector has cooled down. How to store the projector in the soft carrying case (LV-SC02) The soft carrying case is not provided with the projector. Please contact with a store if you want to purchase it. Note: To protect - Canon LV-X420 | User Manual - Page 27
help on using OSD menus.) Note: Keep the password strictly. Without the password, you will not be able to use the projector. If you lose the password, contact Canon Customer Support Center for information on clearing the password. 1. Press the MENU button to open the OSD menu. 2. Press the cursor - Canon LV-X420 | User Manual - Page 28
the Security Lock is enabled. Enter the password in the order you set it at step 5. In case you forget the password, please contact the Canon Customer Support Center. - 25 - - Canon LV-X420 | User Manual - Page 29
Level Take note of the following when setting up the projector: The projector table or stand should be level and sturdy. Position the projector so that it is perpendicular to the screen. To adjust the angle of the picture, turn the Adjustable feet right or left until the desired - Canon LV-X420 | User Manual - Page 30
Adjusting the Zoom, Focus and Keystone 1. Use the zoom ring to resize the projected image Use the Focus ring to sharpen the projected image. 2. Use the KEYSTONE buttons to correct image-trapezoid (wider top, bottom, left side or right side). The keystone control appears on the display. Press / for V - Canon LV-X420 | User Manual - Page 31
Adjusting the Volume 1. Press the Volume buttons on the remote control. The volume control appears on the display. Press the ◄/► buttons on the remote control to adjust volume. 2. Press the MUTE button to turn off the volume. (This feature is available only on the remote). - 28 - - Canon LV-X420 | User Manual - Page 32
that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the projector keypad to navigate and make changes to the OSD. 6 5 1 3 37 2 4 13 7 26 3 5 4 1 1. To enter the OSD, press the MENU button. 2. There are - Canon LV-X420 | User Manual - Page 33
Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1. Press the cursor ▲▼ button to move to the Advanced 1 menu. 2. Press (Enter) / ► to enter the Advanced 1 sub menu. Press the cursor ▲▼ - Canon LV-X420 | User Manual - Page 34
OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting. Main Menu Image Sub Menu Picture Mode Brightness Contrast Analog setting Auto Image Advanced Color Manager Horizontal Position Vertical Position Frequency Tracking Settings - Canon LV-X420 | User Manual - Page 35
Blank, Red, Green, Blue, White Splash Logo On, Off Closed Captioning Off, On KeypadLock Off, On 3D Setting 3D Off, DLP-Link 3D Sync Invert Off, On Test Pattern H Image Shift 3D Format Frame Sequential, Top/Bottom, Side-BySide, Frame Packing None, Grid, White, Red, Green, Blue, Black - Canon LV-X420 | User Manual - Page 36
(ECO, Normal, Smart Eco) Software Version Menu Position Translucent Menu Standby Power Fan Speed Lamp Hour Reset Projector ID Network Advanced 2 Sleep Timer Source Filter Screen Color Color Space Input Level Settings Off, On 0(Off), 1~180 Off, On ECO, Normal, Smart Eco Left, - Canon LV-X420 | User Manual - Page 37
the Presentation mode prioritizes brightness. ・Movie mode: Suitable for projecting movies. ・sRGB mode: Suitable for projecting photos from a digital camera that supports sRGB. Press the cursor ◄► button to enter and adjust the display brightness. Press the cursor ◄► button to enter and adjust the - Canon LV-X420 | User Manual - Page 38
Analog setting Menu Press the MENU button to open the OSD menu. Press ◄► to move to the Image menu. Press ▲▼ to move to the Analog setting menu and then press Enter or ►. Press ▲▼ to move up and down in the Analog setting menu. ITEM DESCRIPTION Horizontal Position Vertical Position Frequency - Canon LV-X420 | User Manual - Page 39
Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the Advanced menu. ITEM DESCRIPTION Brilliant Color Sharpness Gamma Color Temperature Video AGC Video - Canon LV-X420 | User Manual - Page 40
White Balance Press the ENTER button to enter the White Balance sub menu. ITEM R Gain G Gain B Gain R Offset G Offset B Offset DESCRIPTION Press the ◄► buttons to adjust the Red Gain. Press the ◄► buttons to adjust the Green Gain. Press the ◄► buttons to adjust the Blue Gain. Press the ◄► buttons - Canon LV-X420 | User Manual - Page 41
Color Manager Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Color Manager menu and then press Enter or ►. Press ▼▲ to move up and down in the Color Manager menu. ITEM Red Green Blue Cyan Magenta Yellow White DESCRIPTION Select to enter the - Canon LV-X420 | User Manual - Page 42
Settings 1 Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings 1 menu. Press the cursor ▲▼ button to move up and down in the Settings 1 menu. Press ◄► to enter and change values for settings. ITEM Source Projection Aspect Ratio Keystone Digital Zoom - Canon LV-X420 | User Manual - Page 43
Keystone Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▼▲ to move to the Keystone menu and then press Enter or ►. Press ▼▲to adjust vertical values from -30 to 30. Press ◄► to adjust horizontal values from -30 to 30. Audio Press the Menu button to open - Canon LV-X420 | User Manual - Page 44
Advanced 1 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced 1 menu. Press ◄► to enter and change values for setting. ITEM DESCRIPTION - Canon LV-X420 | User Manual - Page 45
. If some case, turn on the 3D feature. 6. Turn on and set up the 3D glasses in accordance with the setup instructions in the document for the 3D glasses.. Note: There are various types of 3D glasses (for DLP Link projectors). Please set up your 3D glasses in accordance with the corresponding setup - Canon LV-X420 | User Manual - Page 46
and down in the Advanced 2 menu. Press ◄► to enter and change values for setting. ITEM Test Pattern H Image Shift V Image Shift DESCRIPTION Press the cursor ◄► button to enter and select internal test pattern. Press the cursor ◄► button to enter and select H Image Shift. Press the cursor ◄► button - Canon LV-X420 | User Manual - Page 47
4 Corner Press (Enter) / ► to enter the 4 Corner sub menu. 1. Press the cursor ▲ / ▼ buttons to select a corner and press ENTER. 2. Press the cursor ▲ / ▼ buttons to adjust vertical and press the cursor ◄ / ► buttons to adjust horizontal. 3. Press MENU to save and Exit the settings. - 44 - - Canon LV-X420 | User Manual - Page 48
button to enter and enable or disable a function to power on the projector only by connecting the AC power cable. Press the cursor ◄► button to enter and select the lamp mode for higher brightness or lower brightness to save lamp life. Press (Enter) / ► to reset all settings to default values. Reset - Canon LV-X420 | User Manual - Page 49
▲▼ button to move up and down in the Settings 2 menu. Select the Status menu and press Enter or ► to enter. ITEM Active Source Video Information Lamp Hours (Eco, Normal, Smart Eco) Software Version DESCRIPTION Display the activated source. Displays resolution/video information for RGB source - Canon LV-X420 | User Manual - Page 50
down in the Advanced 1 menu. Press ◄► to enter and change values for setting. ITEM Menu Position Translucent Menu Standby Power Fan Speed Lamp Hour Reset Projector ID Network DESCRIPTION Press the cursor ◄► button to enter and select different OSD location. Press the cursor ◄► button to enter and - Canon LV-X420 | User Manual - Page 51
Reset Please refer to Resetting the Lamp Hour on page 64 to reset the lamp hour counter. Network ITEM DHCP IP Address Subnet Mask Gateway DNS Apply DESCRIPTION Press the cursor ◄► button to turn DHCP On or Off. Note: If - Canon LV-X420 | User Manual - Page 52
of information about the diverse types of external devices which can be connected to the LAN/RJ45 port and remote/control the projector, as well as the related control commands supporting for each external device, kindly please get contact with the Canon Customer Support Center directly. - 49 - - Canon LV-X420 | User Manual - Page 53
LAN_RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 2. On the PC (Laptop), select Start → Control Panel →Network and Internet. - 50 - - Canon LV-X420 | User Manual - Page 54
3. Right-click on Local Area Connection, and select Properties. 4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP). 5. Click Properties. 6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. - 51 - - Canon LV-X420 | User Manual - Page 55
7. Press the Menu button on the projector. 8. Select Settings2→ Advanced1 → Network 9. After getting into Network, input the following: DHCP: Off IP the IP address: 10.10.10.10. 12. Press (Enter) / ►. The projector is setup for remote management. The LAN/RJ45 function displays as follows. - 52 - - Canon LV-X420 | User Manual - Page 56
CATEGORY ITEM INPUT-LENGTH IP Address 15 Crestron Control IP ID 3 Port 5 Projector Name 10 Projector Location 10 Assigned To 10 DHCP (Enabled) (N/A) IP Address 15 Network Configuration Subnet Mask 15 Default Gateway 15 DNS Server 15 Enabled (N/A) User Password New - Canon LV-X420 | User Manual - Page 57
Preparing Email Alerts 1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for example, Microsoft Internet Explorer). 2. From the Homepage of LAN/RJ45, click Alert Mail Settings. 3. By default, these input boxes in Alert Mail Settings are blank. - 54 - - Canon LV-X420 | User Manual - Page 58
field is the sender's email address (for example, the projector administrator). This is a required field. Select the alert conditions by checking the desired boxes. Note: Fill in all fields as specified. User can click Send Test Mail to test what setting is correct. For sending an e-mail alert - Canon LV-X420 | User Manual - Page 59
way, so called "RS232 by TELNET" for LAN/RJ45 interface. Quick Start-Guide for "RS232 by TELNET" 1. Check and get the IP-Address on OSD of the projector. 2. Make sure that laptop/PC can access the web-page of the projector. 3. Have the TELNET function enabled. See How to have TELNET enabled in - Canon LV-X420 | User Manual - Page 60
How to have TELNET enabled in Windows 7 / 8 / 10 By default installation for Windows, "TELNET" function is not included. But end-user can have it by way of "Turn Windows features On or Off" to be enabled. 1. Open "Control Panel" in Windows 2. Open "Programs" 3. Select "Turn Windows features on or - Canon LV-X420 | User Manual - Page 61
Specsheet for "RS232 by TELNET" : 1. Telnet: TCP 2. Telnet port: 23 (for more detail, kindly please get contact with the Canon Customer Support Center) 3. Telnet utility: Windows "TELNET.exe" (console mode) 4. Disconnection for RS232-by-Telnet control normally: Close Windows Telnet utility directly - Canon LV-X420 | User Manual - Page 62
. ITEM Sleep Timer Source Filter Screen Color Color Space Input Level DESCRIPTION Press the cursor ◄► button to enter and set Sleep timer. The projector automatically turns off after the preset period of time. Press (Enter) / ► to enter the Source Filter menu. See page 60 for more information - Canon LV-X420 | User Manual - Page 63
Source Filter Press the ENTER button to enter the Source Filter sub menu. If Enable is selected , the source becomes the object of Auto search. ITEM COMPUTER 1 COMPUTER 2 Composite Video S-Video HDMI 1 HDMI 2 / MHL DESCRIPTION Press the ◄► buttons to enter and enable or disable the COMPUTER 1 - Canon LV-X420 | User Manual - Page 64
may be broken. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. Additionally, with ceiling-mounted projectors, the lamp may fall out when you open the lamp cover or while you are attempting to replace it. During replacement - Canon LV-X420 | User Manual - Page 65
2. Remove the lamp cover. 3. Disconnect the lamp connector 1 2 4. Remove the two screws from the lamp module. 5. Lift the module handle up. 6. Pull firmly on the module handle to remove the lamp module. - 62 - - Canon LV-X420 | User Manual - Page 66
must be installed flush with the connector base as shown in the image below. A gap between the Lamp Connector and the connector base will cause damage to the projector. The following images illustrate correct and incorrect Lamp Connector installations. No Gap Correct Gap Incorrect 8. Close the - Canon LV-X420 | User Manual - Page 67
move to the Settings 2 menu. Press the cursor ▼▲ button to move down to Advanced 1 and press enter. 3. Press the cursor ▼▲ button to move down to Lamp Hour Reset. 4. Press the cursor ► or Enter button. A message screen appears. 5. Press the four buttons in order, to reset the - Canon LV-X420 | User Manual - Page 68
paper. The lens surface is easily damaged, so do not use a hard cloth or tissues. Cleaning the Case Refer to the following to clean the projector case. 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then - Canon LV-X420 | User Manual - Page 69
Using the Kensington Lock Using the Kensington Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensington security cable. The security lock - Canon LV-X420 | User Manual - Page 70
and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact Canon Customer Support Center. Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check - Canon LV-X420 | User Manual - Page 71
and wait for one (1) minute before restarting the projector. If the Power or Lamp LEDs are still blinking or any other situation that isn't listed in the chart above, please contact Canon Customer Support Center. Problem and Countermeasures Image Problems Problem: No image appears on the screen - Canon LV-X420 | User Manual - Page 72
on the Image->Advanced menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the - Canon LV-X420 | User Manual - Page 73
, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem: For servicing, return the projector to the place you purchased it or Canon Customer Support Center. - 70 - - Canon LV-X420 | User Manual - Page 74
periphery to center (*2) Speaker Supported input signal types LV-HD420 LV-X420 1-chip DLP™ Time division color extraction, sequential display 0.65'' / 16:9 0.55'' / 4:3 2,073,600 (1920 X 1080) X 1 panel 786,432 (1024 X 768) X 1 panel V:65%, Fixed Manual (X 1.5） Manual f=20.7 - 31.1mm F=2.42 - Canon LV-X420 | User Manual - Page 75
10BASE-T) Service port Power feeding (1.5A) 40/36 dB (Lamp mode Manual(CD-ROM),Important Information and Warranty Card *1: Picture mode: Presentation *2: Compliance with ISO21118-2012 *3: Optimizes the contrast depending on the brightness of each scene by adjusting lamp output. • Using the projector - Canon LV-X420 | User Manual - Page 76
Projection Distance vs. Projection Size Projection Distance and Size Table LV-HD420 Image size (16:9) Projection Distance Diagonal Width Height Wide Table inch cm cm m inch m inch 30 66 37 - - 1.39 55 40 89 50 1.23 48 1. - Canon LV-X420 | User Manual - Page 77
LV-X420 Image size (16:9) Diagonal Width Height inch cm cm 30 61 46 40 81 61 60 122 91 80 163 122 100 203 152 - Canon LV-X420 | User Manual - Page 78
Timing Mode Table SIGNAL RESOLUTION H-SYNC (KHZ) NTSC － 15.734 PAL/SECAM － 15.625 720 x 400 37.9 640 x 480 31.5 640 x 480 37.9 640 x 480 37.5 640 x 480 43.3 800 x 600 35.2 800 x 600 37.9 800 x 600 46.9 800 x 600 48.1 800 x 600 53.7 800 x 600 76.3 1024 x 768 48.4 - Canon LV-X420 | User Manual - Page 79
1080p 56.3 50.0 － O － O 1080p 27 24.0 － O － O 1080p 28 25.0 － O － O 1080p 33.7 30.0 － O － O O：Frequency supported -：Frequency not supported *：LV-HD420 native resolution of the panel is 1920 x 1080 LV-X420 native resolution of the panel is 1024 x 768 The aspect ratio of an - Canon LV-X420 | User Manual - Page 80
Projector Dimensions 314mm [12.4"] 218mm [8.6"] 112mm [4.4"] - 77 - - Canon LV-X420 | User Manual - Page 81
REGULATORY COMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a - Canon LV-X420 | User Manual - Page 82
Command Note: "CR" mean Carriage Return XX=00-98, projector's ID, XX=99 is for all projectors Return Result P=Pass / F=Fail n: 0:Disable/1: Enable/Value(0~9999 Xh Xh 53h 30h 30h 30h 36h 0Dh Power On Power Off Resync Get Lamp Hours System Reset 56h Xh Xh 47h 30h 30h 30h 37h 0Dh Get System - Canon LV-X420 | User Manual - Page 83
Command Group 01 ASCII HEX Function VXXS0105n 56h Xh Xh 53h 30h 31h 30h 35h nh 0Dh Set Sharpness VXXG0106 56h Xh Xh 47h 30h 31h 30h 36h 0Dh Get Color Temperature VXXS0106n 56h Xh Xh 53h 30h 31h 30h 36h nh 0Dh Set Color Temperature VXXG0107 56h Xh Xh 47h 30h 31h 30h 37h 0Dh Get Gamma - Canon LV-X420 | User Manual - Page 84
n=0~1 56h Xh Xh 53h 30h 33h 31h 35h nh 0Dh Set 3D Mode 0:Off 1:DLP 56h Xh Xh 47h 30h 33h 31h 36h 0Dh Get 3D sync inverter n=0~1 56h Xh FP 56h Xh Xh 47h 30h 33h 31h 39h 0Dh Get Lamp mode n=0~2 56h Xh Xh 53h 30h 33h 31h 39h nh 0Dh Set Lamp mode 0:Eco 1:Normal 2:Smart ECO 56h Xh Xh 47h 30h - Canon LV-X420 | User Manual - Page 85
Command Group 03 ASCII HEX Function Description VXXG0331 VXXS0331n VXXG0332 VXXS0332n VXXG0333 VXXS0333n VXXG0334 VXXS0334n VXXG0335 VXXS0335n VXXG0336 VXXS0336n VXXG0337 VXXS0337n VXXG0338 VXXS0338n VXXG0339 VXXS0339n VXXG0340 VXXS0340n VXXG0341 VXXS0341n VXXG0342 VXXS0342n VXXG0343 VXXS0343n - Canon LV-X420 | User Manual - Page 86
Command Group 03 ASCII HEX Function Description VXXG0351 VXXS0351n VXXG0352 VXXS0352n VXXG0353 VXXS0353n VXXG0354 VXXS0354n VXXG0355 VXXS0355n VXXG0356 VXXS0356n VXXG0357 VXXS0357n VXXG0358 VXXS0358n 56h Xh Xh 47h 30h 33h 35h 31h 0Dh Get the Cyan Gain n=-100~100 56h Xh Xh 53h 30h 33h 35h 31h - Canon LV-X420 | User Manual - Page 87
INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A. INC. One Canon Park, Melville, New York 11747, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANON EUROPE LTD. 3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET United
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
 |
 |
MULTIMEDIA PROJECTOR
User’s Manual
BEFORE USING, BE SURE TO READ THIS USER'S MANUAL.
Read the “Safety Instructions” in this manual thoroughly and use cor-
rectly the projector.
Store this user's manual in a convenient location where you can refer
to it easily.