Canon LX-MW500 User Manual
Canon LX-MW500 Manual
 |
View all Canon LX-MW500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Canon LX-MW500 manual content summary:
- Canon LX-MW500 | User Manual - Page 1
ENGLISH MULTIMEDIA PROJECTOR LX-MW500/LX-MU500 User's Manual - Canon LX-MW500 | User Manual - Page 2
through a web browser (e-Control 52 Controlling the projector using PJLink™ application 54 Menu operation 57 Maintenance 64 Care of the projector 64 Lamp information 66 Indicators 71 Troubleshooting 72 Specifications 73 Projector specifications 73 Dimensions 75 Timing chart 76 Control - Canon LX-MW500 | User Manual - Page 3
accidents. If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in the user's manual. If the problem still persists, contact the Canon Customer Support Center. CAUTION RISK - Canon LX-MW500 | User Manual - Page 4
. Ensure Network Security Take measures to ensure network security. Note that Canon is not liable in any way for direct or indirect loss from / or other countries. • HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. • PJLink - Canon LX-MW500 | User Manual - Page 5
SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY BECOME DETERIORATED. READ AND KEEP THIS MANUAL FOR LATER USE. All the safety and operating instructions should be read before beginning to operate the product. Read all of the - Canon LX-MW500 | User Manual - Page 6
service personnel under the following conditions: a When the power cord or plug is damaged or frayed. b If liquid has been spilled into the projector. c If the projector has been exposed to rain or water. d If the projector does not operate normally after following the operating instructions - Canon LX-MW500 | User Manual - Page 7
Cord supplied with this projector meets the requirements for EQUIPMENT AND EASILY ACCESSIBLE. For the U.S. and Canada, LAMP (S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED or your household waste disposal service or visit www.canon-europe.com/weee, or www.canon-europe.com/battery. For - Canon LX-MW500 | User Manual - Page 8
Multimedia Projector, Model: LX-MW500/LX- instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Park, Melville, New York 11747, U.S.A. Tel No. 1-800-OK-CANON (1-800-652-2666) Safety Symbols in this Manual - Canon LX-MW500 | User Manual - Page 9
or bundled. • Do not use a damaged power cord. If your power cord is damaged, contact the Canon Customer Support Center. • Do not use any power cord other than the type that is included with this projector. • Be sure to connect the ground wire of the power cord to ground. Failure to do so - Canon LX-MW500 | User Manual - Page 10
parts that are hot. These could cause an electric shock or burn. If inspection, maintenance or repair is required, contact the Canon Customer Support Center. • Do not disassemble or modify the projector (including consumable parts) or the remote control. • Do not insert any object into vents in the - Canon LX-MW500 | User Manual - Page 11
or malfunction. It is recommended that periodic maintenance of the projector be performed. For details of maintenance costs, contact the Canon Customer Support Center. Precautions on the lamp This projector uses a high-pressure mercury lamp, which must be handled carefully and correctly as described - Canon LX-MW500 | User Manual - Page 12
glass may be scattered inside the projector. Contact the Canon Customer Support Center for cleaning and inspection of the projector interior and lamp replacement. Caution When handling the lamp, pay attention to the following points. •Be sure not to handle the lamp immediately after it has been used - Canon LX-MW500 | User Manual - Page 13
properly express discomfort with 3D content viewing. Children who are six year of age or younger should not view 3D content. • The optimum 3D viewing distance from the screen is about 3 times of the vertical screen size or more and your eyes should be level with the screen. 13 - Canon LX-MW500 | User Manual - Page 14
has evaporated for the image projected to return to normal. • Do not install the projector in a location where the temperature is high or low. Doing so may cause a malfunction. LX-MW500 Operating temperature: 0°C to 40°C, Operating humidity level: 10% to 90% (non-condensing) Storage temperature - Canon LX-MW500 | User Manual - Page 15
ENGLISH Contents of package Projector (US) (EU) (China) Power cord 1.8 m (70.8") Computer cable 1.8 m (70.8") (5K.1VC09.501) CD & QSG Important Information Warranty card Remote control (type number: LV-RC08) Battery (type number: CR2025) 15 - Canon LX-MW500 | User Manual - Page 16
17 18 19 25 26 29 28 5 29 28 28 8 9 10 11 20 21 22 23 24 27 28 5 1. External control panel (See "Projector" on page 17 for details.) 2. Lamp cover 3. Vent (heated air exhaust) 4. Speaker 5. Adjuster foot 6. Projection lens 7. Front IR remote sensor 8. Lens shift wheel 9. Focus ring and Zoom - Canon LX-MW500 | User Manual - Page 17
the status of the lamp. Lights up or flashes when the lamp has developed a problem. See "Indicators" the projector between standby mode and on. See "Starting up the projector" on page 33 and "Shutting down the projector" Up, / Down) Manually corrects distorted images resulting from an angled projection. - Canon LX-MW500 | User Manual - Page 18
RC08 9. Keystone/Arrow keys ( / Up, / Down) Manually corrects distorted images resulting from 1 8 an angled projection. 46 for details. 5. TIMER When you are under the MHL connection mode and the projector OSD is off, these buttons are available for controlling your smart device: arrow keys, - Canon LX-MW500 | User Manual - Page 19
remote control sensors are located on the front and top of the projector. The distance between the remote control and the sensors should not exceed 8 replaced by an incorrect type. • Dispose of used batteries according to the instructions. • Use of a battery of wrong type may cause explosion. Use - Canon LX-MW500 | User Manual - Page 20
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Third party software support Canon Inc., Canon's affiliated companies, as well as sales companies do not offer any support services for these programs. We are unable to respond to questions or inquiries from you or any other - Canon LX-MW500 | User Manual - Page 21
size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of the possible installation locations: 1. Front Table Select this location with - Canon LX-MW500 | User Manual - Page 22
Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size. 16:10 is the native aspect ratio of LX-MU500/LX-MW500. To be able to project a complete 16:9 (widescreen) - Canon LX-MW500 | User Manual - Page 23
placement of the screen in relation to the horizontal plane of the projector. LX-MU500: If your measured projection distance was 2.5 m and your screen aspect ratio is 16:10, the closest match in the "Distance from the screen: L" column is 2.2 m to 3.5 m. Looking across this row shows that - Canon LX-MW500 | User Manual - Page 24
varies depending on the distance between the screen and the projector. Front projection W A B H Hd A=B L LX-MW500 (16:10) Diagonal Canon recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector - Canon LX-MW500 | User Manual - Page 25
shift control provides flexibility for installing your projector. It allows the projector to be positioned slightly above or below adjust the projected image position. Lens shift adjustable range LX-MW500 Vertical shift: +55%~+57.5% 0.025H H 0.05H LX-MU500 Vertical shift: +52.5%~+55% 0.025H H 0. - Canon LX-MW500 | User Manual - Page 26
cables are firmly inserted. • See the user's manual of each device for details about its connections. • Contact your dealer for details about its connections. • In the connections shown below, some cables may not be included with the projector. They are commercially available from electronics stores - Canon LX-MW500 | User Manual - Page 27
you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below: HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible devices like DTV tuners, DVD players and - Canon LX-MW500 | User Manual - Page 28
, set it as follows. EXPAND or ENHANCED -> NORMAL • See the User's Manual of your DVD player for details. • When you switch to HDMI input, the other end of the cable to the HDMI-1/MHL input terminal on the projector. The final connection path should be like that shown in the following diagram: - Canon LX-MW500 | User Manual - Page 29
continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: 1. Take a Component Video to RGB (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component - Canon LX-MW500 | User Manual - Page 30
can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take an S-Video cable and connect one end to the S-Video output terminal of the Video source device. 2. Connect the - Canon LX-MW500 | User Manual - Page 31
continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. Take a Video cable and connect one end to the composite Video output terminal of the Video source device. 2. Connect - Canon LX-MW500 | User Manual - Page 32
. Notebook computer Control computer Blu-ray player VGA IN YPbPr Projector RJ45 Lan HDMI HDBaseT matrix RS232 IR TX RJ45 HD Connect cable rated at CAT5e or better. • Maximum transmission distance is 100 m. • However, maximum transmission distance may be shorter in some environments. • Do - Canon LX-MW500 | User Manual - Page 33
of trouble with the projector, use an electrical outlet having an earth leakage breaker to supply the power to the projector. If lamp becomes stable. This is not a product malfunction. 3. If the projector is activated for the first time, select your OSD language following the on-screen instructions - Canon LX-MW500 | User Manual - Page 34
Blank Timer Panel Key Lock Sleep Timer Splash Screen OK Front Table 20 min Disable Off Disable Canon Analog RGB MENU Exit 4. Press / / / to select a preferred language and press OK/IMAGE. 5. Press MENU on the projector or remote control to leave and save the settings. Analog RGB MENU Exit 34 - Canon LX-MW500 | User Manual - Page 35
necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall. Setting a password Once a password has been set, the projector cannot be used unless the correct password is entered every time the projector is started. 1. Open the OSD menu and go to - Canon LX-MW500 | User Manual - Page 36
page with 'Off' shown in the row of Power On Lock. You will not have to enter the password next time you turn on the projector. • If the password is incorrect, the password error message is displayed lasting for three seconds, and the message 'INPUT PASSWORD' is displayed for your retry - Canon LX-MW500 | User Manual - Page 37
the INPUT menu is On (which is the default of this projector) if you want the projector to automatically search for the signals. You can also manually cycle through the available input signals. 1. Press INPUT on the projector or remote control. A source selection bar is displayed. 2. Press / until - Canon LX-MW500 | User Manual - Page 38
projector are not parallel to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 39 for details. • Do not look into the lens while the lamp is on. The strong light from the lamp for appropriate projection distance because of small - Canon LX-MW500 | User Manual - Page 39
becomes a trapezoid due to angled projection. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the - Canon LX-MW500 | User Manual - Page 40
AUTO PC to restore the picture to its original size. You can also press repeatedly until it is restored to the original size. **When the projector and computer are connected via USB, the function (Page UP/Page DOWN) which operates the computer from the remote controller is set. The picture can - Canon LX-MW500 | User Manual - Page 41
and the white portions are active areas. OSD menus can be displayed on those unused black areas. 1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width or its vertical height. This is suitable when you want to make most use of the screen without - Canon LX-MW500 | User Manual - Page 42
follow one of the following steps. • Press OK/IMAGE on the remote control or projector repeatedly until your desired mode is selected. • Go to the PICTURE > Image Mode mode: Suitable for projecting photos from a digital camera that supports sRGB. Compatible with the sRGB standard. 4. Movie mode: - Canon LX-MW500 | User Manual - Page 43
vibrant colors in picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors. If you prefer images with that quality, select On. If you do not need it, select Off. On - Canon LX-MW500 | User Manual - Page 44
independently adjust its range and saturation according to your preference. If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc. You can project any image from the disc on the screen and enter - Canon LX-MW500 | User Manual - Page 45
timer is off, pressing this key displays a confirmation message. You can decide whether to activate the timer or not by following the on-screen instruction. • If the timer is already on, pressing this key displays a confirmation message. You can decide whether to restart, continue or turn off the - Canon LX-MW500 | User Manual - Page 46
the image. The word 'FREEZE' will be displayed in the upper left corner of the screen. To release the function, press any key on the projector or remote control. Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected - Canon LX-MW500 | User Manual - Page 47
II POWER a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds (LX-MW500) /120 seconds (LX-MU500) to cool down the projector. 3. Once the cooling process finishes, the POWER indicator light is a steady - Canon LX-MW500 | User Manual - Page 48
• If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press II POWER again to start the projector after the fans stop and the POWER indicator light turns orange. 48 - Canon LX-MW500 | User Manual - Page 49
ENGLISH Watching 3D content This projector supports 3D content display using the DLP Link system. This projector supports 3D image signals in Frame Sequential/Frame Packing/Top-Bottom/Side-BySide format. You need the following items to project and watch 3D content. • 3D - Canon LX-MW500 | User Manual - Page 50
sure to check with the child. The minimum recommended age for viewing 3D content is six years old. • Make sure you are at an appropriate distance from the front of the screen when viewing 3D content. Make sure you are at least three times the height of the screen away from - Canon LX-MW500 | User Manual - Page 51
computer using a web browser or PJLink™ application when the computer and the projector are connected to the same local area network. This projector supports Crestron® software and PJLink™. An example of connecting the projector to computer. External hub Computer LAN cable (option) (100BASE-TX or - Canon LX-MW500 | User Manual - Page 52
OS X v10.4/v10.5/v10.6/v10.7. 1. Enter the IP address of the projector in the address bar of your browser and press enter. (for example, . To switch input source, click on your desired source. When you use the projector control panel or remote control to change the OSD menu settings, it may take - Canon LX-MW500 | User Manual - Page 53
ENGLISH i. When using the Crestron Control System, please refer to the user manual of Crestron Control system for setup information. ii. You can name the projector, keep track of its location and the person in charge of it. This column allows a maximum of 22 single-byte characters. iii. You can - Canon LX-MW500 | User Manual - Page 54
Error". Error Status Description 3: Lamp fail The lamp fails to ignite or turns off during operation. 3: Over Temp The projector temperature is too high or or.jp/english) • This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by - Canon LX-MW500 | User Manual - Page 55
time (hour) calculated based on that Lamp Mode is Economic.) 2nd value: 0 = Lamp off, 1 = Lamp on The following value is returned. "11 12 21 22 31" The command responds with the projector name specified in the Tools page. "Canon" is returned. "LX-MU500" or "LX-MW500" is returned. DMD resolution is - Canon LX-MW500 | User Manual - Page 56
the power is turned on. • Use 1 computer to control/monitor 1 projector. • For how to control/monitor using PJLink™, see the operation manual of the PJLink™ application you use. • When you monitor the projector's operating state using this function by issuing inquiry commands successively, issue an - Canon LX-MW500 | User Manual - Page 57
ENGLISH Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu 1. DISPLAY Sub-menu Screen Color Aspect Keystone Corner Adjustment Position Phase H. Total Dots D.Zoom 3D 2. PICTURE 3D Sync Image Mode Brightness - Canon LX-MW500 | User Manual - Page 58
Volume Menu Settings Menu Display Time Menu Position Lamp Settings Filter Settings Lamp Mode Reset Lamp Time Lamp Time Filter Mode Reset Filter Time Front min Off*/On Disable*/30 min/1 hr/2 hr/3 hr/4 hr/ 8 hr/12 hr Black/Blue/Canon* On/Off* On/Off* 5 sec/10 sec/15 sec*/20 sec/ 25 sec/30 sec - Canon LX-MW500 | User Manual - Page 59
DNS Server Apply Reset All Settings Input Image Mode Current System Status Color Format Resolution Lamp Time Filter Time • * Indicates an item that is factory-set. • The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the - Canon LX-MW500 | User Manual - Page 60
or reduces the projected image. See "Magnifying and searching for details" on page 40 for details. This projector features a 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more the inversion of the image depth, enable this function to correct the problem. 60 - Canon LX-MW500 | User Manual - Page 61
Pre-defined image modes are provided so you can optimize your projector image set-up to suit your program type. See "Selecting for details. See "Choosing a location" on page 21 for details. Allows the projector to turn off automatically if no input signal is detected and no operation is made - Canon LX-MW500 | User Manual - Page 62
47 for details. See "Personalizing the projector menu display" on page 47 for details. Lamp Mode See "Setting Lamp Mode as Economic" on page 66 for details. Reset Lamp Time See "Resetting the lamp timer" on page 70 for details. Lamp Time See "Getting to know the lamp hour" on page 66 for details on - Canon LX-MW500 | User Manual - Page 63
closed captioned (usually marked as "CC" in TV listings). When the projector displays OSD or any dialog, captions are not displayed at the same the input signal. Color Format Shows input system format. Lamp Time Displays the number of hours the lamp has been used. Filter Time Displays the number of - Canon LX-MW500 | User Manual - Page 64
be done by authorized service technicians only. Contact your dealer for instructions. What you can do yourselves on a regular basis is to keep the lens clean, keep the cabinet clean, and replace the air filter. Never remove any parts of the projector except the lamp and air filter cover. Contact - Canon LX-MW500 | User Manual - Page 65
the filter timer. Highlight Reset and press OK/IMAGE. The reset time will be reset to '0'. Storing the projector If you need to store the projector for an extended time, please follow the instructions below: • Make sure the temperature of the storage area is within the recommended range for the - Canon LX-MW500 | User Manual - Page 66
and press / . • When this mode is switched, the projected images may flicker. • If this mode is frequently switched, the lamp may be deteriorated. Setting Auto Power Off This function allows the projector to turn off automatically if no input source is detected and no operation is made by user after - Canon LX-MW500 | User Manual - Page 67
. If the lamp is not replaced beforehand, it must be replaced after 2000 hours usage. The lamp MUST be replaced before the projector will operate normally. Notice Replace Lamp Now Lamp>2000 Hours OK WARNING Out of Lamp Usage Time Replace lamp (Refer to user manual) Then reset lamp timer OK 67 - Canon LX-MW500 | User Manual - Page 68
waste regulations to dispose of this lamp in a proper manner. • Be sure to use the lamp dedicated to this projector, LX-LP02. Use of other lamps may cause a failure of the projector. 1. Turn the power off and disconnect the projector from the wall socket. If the lamp is hot, avoid burns by waiting - Canon LX-MW500 | User Manual - Page 69
in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 7. As shown in - Canon LX-MW500 | User Manual - Page 70
screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screws. 13. Restart the projector. Do not turn the power on with the lamp cover removed. Resetting the lamp timer 14. After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP - Canon LX-MW500 | User Manual - Page 71
. Normal operation. Normal power-down cooling. FW Download. Color Wheel start fail. Scaler shutdown fail (data abort). Burn-in ON Burn-in OFF Lamp error in normal operation. Lamp is not lit up. Fan 1 error (the actual fan speed is +25% outside the desired speed). Fan 2 error (the actual fan speed is - Canon LX-MW500 | User Manual - Page 72
Troubleshooting The projector does not turn on Cause Remedy There is no power from the power cord. Attempting to turn the projector on again during the cooling process. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has - Canon LX-MW500 | User Manual - Page 73
ENGLISH Specifications Projector specifications All specifications are subject to change without notice. Model name Display system Optical system Type Size / Aspect ratio Drive system Number dots / Total number dots LX-MW500 LX-MU500 1-CHIP DLP™ Time division color extraction, sequential - Canon LX-MW500 | User Manual - Page 74
LX-MW500 LX USB mini B Service port USB type Impedance = 47k Ω or more 36 / 33dB (Lamp mode: normal/eco) Operating temperature 0°C (32°F) to Manual (this manual), Important Information and Warranty Card • *1 Compliance with ISO21118-2012 • *2 LX-MU500 only • Note that using the projector - Canon LX-MW500 | User Manual - Page 75
ENGLISH Dimensions 465 mm (W) x 123 mm (H) x 264 mm (D) / 18.3 in (W) x 4.8 in (H) x 10.4 in (D) (including the protrusion) 264 mm (10.4") 123 mm (4.8") 465 mm (18.3") Tolerance:±2 mm (0.08 in) 75 - Canon LX-MW500 | User Manual - Page 76
Timing chart Supported timing for PC input Resolution Mode Refresh Rate (Hz) 720 x 400 640 x 480 800 x 600 1024 x 768 1152 x 864 1280 x 720 1280 x 768 1280 x 800 - Canon LX-MW500 | User Manual - Page 77
1920 x 1200@60Hz WUXGA_60**** (Reduce Blanking) 59.950 74.038 154.00 *Supported timing for 3D signal in Frame Sequential, Top-Bottom and Side-By-Side formats. **Supported timing for 3D signal in Frame Sequential format. ***Supported timing for 3D signal in Top-Bottom and Side-By-Side formats - Canon LX-MW500 | User Manual - Page 78
timing for HDMI (HDCP) input Supported PC timings Resolution Mode 720 x 400 640 x 480 800 x 600 1024 x 768 1152 x 864 1280 x 720 1280 x 768 1280 x 800 1280 x 1024 1280 x 960 1360 x - Canon LX-MW500 | User Manual - Page 79
Bottom and Side-By-Side formats. ****Supported timing for 3D signal in Top-Bottom format. *****LX-MU500 only. Supported MHL timings Timing 480i 480p 576i 576p 25 37.5 45 27 28.13 33.75 28.13 33.75 56.26 67.5 Supported Video timings Timing 480i* 480p 576i 576p 720/50p** 720/60p** 1080/24P** - Canon LX-MW500 | User Manual - Page 80
.25 50 148.5 1080/60P 1920 x 1080 67.5 60 148.5 Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration. Supported timing for Video and S-Video inputs Video mode NTSC PAL SECAM PAL-M PAL-N PAL-60 NTSC4.43 Horizontal Frequency (kHz) 15.73 15.63 15 - Canon LX-MW500 | User Manual - Page 81
ENGLISH Control Commands You can control this projector by sending commands via CONTROL port or LAN port. System Requirement CONTROL port Connection Cable 9-pin RS-232-C Cable (Crossover) Communication Mode RS-232-C asynchronous, - Canon LX-MW500 | User Manual - Page 82
:10 Aspect Status Front Table Rear Table Front Ceiling Rear Ceiling Image flip H/V Status Auto search On Auto search Off Auto search status Lamp Hour Lamp Mode Normal Lamp Mode Economic Lamp Mode Status MUTE=ON MUTE=OFF GET=MUTE RC=VOL_P RC=VOL_M GET=AVOL IMAGE=PRESENTATION - Canon LX-MW500 | User Manual - Page 83
Response Read/ Write Condition W Success Illegal format : Don't W exist command or structure Unsupported item: W this command parameter can't support W Block item: Current state can't use. R Success Response Example i:OK e:0002 INVALID_COMMAND < BLANK=ON > i:OK - Canon LX-MW500 | User Manual - Page 84
R Unsupported item: this command parameter can't support e:000A INVALID_PARAMETER < GET=INVALID > e:000A INVALID_PARAMETER • If the projector didn't receive to finish a command within 5 seconds, it will timeout and you need to resend the command. • No case sensitive. 84 - Canon LX-MW500 | User Manual - Page 85
INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A. INC. One Canon Park, Melville, New York 11747, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANON EUROPE LTD. 3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET United
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
 |
 |
ENGLISH
MULTIMEDIA PROJECTOR
LX-MW500/LX-MU500
User’s Manual