Canon REALiS 4K600STZ User Manual

Canon REALiS 4K600STZ Manual

Get Canon REALiS 4K600STZ PDF manuals and user guides View all Canon REALiS 4K600STZ manuals
Add to My Manuals
Save this manual to your list of manuals

Canon REALiS 4K600STZ manual content summary:

  • Canon REALiS 4K600STZ | User Manual - Page 1
    Advanced Guide Basic Guide Safety Instructions Before Use Installation Procedure Connection Procedure Projection Procedure Convenient Features Using Menus Menu Configuration Menu Settings Using the Projector on a Network Advanced Projection Maintenance Product Specifications Troubleshooting ENG
  • Canon REALiS 4K600STZ | User Manual - Page 2
    a Canon projector. The 4K600STZ Multimedia Projector is a high-performance laser projector capable of projecting high-resolution computer screens and high-quality digital images on a large screen. This Manual This is the user's manual for the 4K600STZ Multimedia Projector (hereafter, "projector
  • Canon REALiS 4K600STZ | User Manual - Page 3
    Table of Contents How to Use This Manual 2 Projector Highlights 4 Safety Instructions 6 Safety Symbols in this Manual 12 Precautions for Use 13 Installation and Handling Precautions 14 Laser Precautions 16 Precautions for the Batteries of the Remote Control 18 For Safe Use 20 Before
  • Canon REALiS 4K600STZ | User Manual - Page 4
    , at 559 x 624 x 201 mm (22.0 x 24.6 x 7.9 in., W x D x H). Features a laser light source that lasts longer than traditional mercury lamps. (P202) Supports Fully Digital Input Compatible with HDMI: 2 (4K / Deep Color / HDCP2.2), the projector enables 4K projection (up to 4096 x 2160 at 60 Hz) via
  • Canon REALiS 4K600STZ | User Manual - Page 5
    also supports Wi-Fi. In Projector Access Point (PJ AP) mode, the projector can be connected to up to five computers without using a wireless access point. Quiet Mode This feature reduces laser output from the light source to less than half and lowers the speed of the cooling fan to reduce noise
  • Canon REALiS 4K600STZ | User Manual - Page 6
    accidents. If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in the back of this manual. If the problem still persists, contact the Canon Customer Support Center. CAUTION
  • Canon REALiS 4K600STZ | User Manual - Page 7
    At least 2 cm (0.8") • Do not cover the ventilation slots on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous. • If the projector is unused for an extended time, unplug the projector from the power outlet. • Do not project the same image for
  • Canon REALiS 4K600STZ | User Manual - Page 8
    ■ READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. All the safety and operating instructions should be read before beginning to operate the product. Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Do not
  • Canon REALiS 4K600STZ | User Manual - Page 9
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally after following the operating instructions
  • Canon REALiS 4K600STZ | User Manual - Page 10
    Safety Instructions AC Power Cord Requirement The AC Power Cord supplied with this projector meets the requirements for use in the country you , waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www.canon-europe.com/battery. 10
  • Canon REALiS 4K600STZ | User Manual - Page 11
    if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation required to take adequate measures. The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class A . Use
  • Canon REALiS 4K600STZ | User Manual - Page 12
    Safety Instructions Safety Symbols in this Manual This section describes the safety symbols used in this manual. Important projector safety always observe this information. Denotes the risk of eye injury from laser emission if usage restrictions are not observed. Denotes prohibited actions.
  • Canon REALiS 4K600STZ | User Manual - Page 13
    plug from the power outlet and contact the Canon Customer Support Center. Failure to do so could cause a fire or result in an electric shock. • If smoke is emitted • If an unusual smell or noise is emitted • If water or other liquid has entered the projector • If metal or any other foreign material
  • Canon REALiS 4K600STZ | User Manual - Page 14
    Safety Instructions Pay attention to the following points regarding the power source containers containing a liquid on top of the projector. • Do not touch the projector itself, the power cord, or the cable if lightening strikes. • Do not move the projector until you have switched off the power,
  • Canon REALiS 4K600STZ | User Manual - Page 15
    -voltage components as well as parts that are hot. If inspection, maintenance or repair is required, contact the Canon Customer Support Center. • Do not disassemble or modify the projector (including consumable parts) or the remote control. • Do not look directly into the exhaust vents during use
  • Canon REALiS 4K600STZ | User Manual - Page 16
    from laser light. • The Laser module is equipped in this product. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. • For assistance when disposing of the projector, contact the Canon Customer Support Center
  • Canon REALiS 4K600STZ | User Manual - Page 17
    Safety Instructions Safety Instructions 17
  • Canon REALiS 4K600STZ | User Manual - Page 18
    Safety Instructions Precautions for the Batteries of the Remote Control Pay attention to the following points regarding handling of batteries. Failing to do so could result in a
  • Canon REALiS 4K600STZ | User Manual - Page 19
    Safety Instructions Safety Instructions Pay attention to the following points regarding installation and handling of the projector. • If the projector will not be used for a long period of time, be sure to remove the power plug from the power outlet to ensure safety. Failure to
  • Canon REALiS 4K600STZ | User Manual - Page 20
    room temperature rises abruptly, moisture in the air may condense on the lens and mirror, causing the image to become blurred. • Do not install the projector in a location where the temperature is high or low. Doing so may cause a malfunction. The temperature range for operation and storage are as
  • Canon REALiS 4K600STZ | User Manual - Page 21
    alone. Have at least one assistant. Precautions for Installation Be sure to read "Safety Instructions" and "For Safe Use" (P6 - P20). Also take the following precautions during installation. • Do not strike the projector or subject it to impact. Doing so may cause a malfunction. • Do not install
  • Canon REALiS 4K600STZ | User Manual - Page 22
    projected to return to normal. ■ At Altitudes above 2,300 m (7,545.8'), Adjust the Settings Projector settings must be adjusted when using the projector at altitudes of 2,300 m (7,545.8') or higher. Specifically, refer to instructions for [High altitude] (P111) in the [Install settings] menu. 22
  • Canon REALiS 4K600STZ | User Manual - Page 23
    (0.8") from the air intake vent on the bottom of the projector. • There are no options for installing the projector other than the ceiling attachment. • When mounting the projector on the ceiling, it is more convenient to install the projector right-side up, with the adjustable feet facing down. 23
  • Canon REALiS 4K600STZ | User Manual - Page 24
    Before Installation ■ Precautions for Portrait (Upright) Installation • Do not block the air intake or exhaust vents. In particular, because there is an air intake vent on the bottom, always ensure a minimum clearance of 2 cm (0.8") from the bottom. • Note that no mounting brackets or similar
  • Canon REALiS 4K600STZ | User Manual - Page 25
    Ensure Network Security Take measures to ensure network security. Note that Canon is not liable in any way for direct or indirect loss from firewall or the like, instead of direct Internet connections. • When using the projector in a wireless network, also configure the Wi-Fi security settings. •
  • Canon REALiS 4K600STZ | User Manual - Page 26
    EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NO SUPPORT Canon Inc., and all its subsidiaries or its dealers do not make any support service regarding the source code. Canon Inc., and all its subsidiaries or its dealers shall not respond to any questions or
  • Canon REALiS 4K600STZ | User Manual - Page 27
    control (AA size x2) The remote control can also be used in a wired connection with the projector. (P36) • Power cord (1.8 m / 5.9') For Continental Europe • Lens cap • User's Manual (CD-ROM) For the U.S.A. and Canada • Important Information • Warranty Card ■ Lens Cap Always remove the lens
  • Canon REALiS 4K600STZ | User Manual - Page 28
    Before Use Part Names Projector ■ Front Side Terminals and connectors (P32) Power cord connector (P51) LED indicators (P30) Air intake vent Air filter (P194) Do not block the air intake.
  • Canon REALiS 4K600STZ | User Manual - Page 29
    Before Use ■ Bottom Air intake vent Before Use Side Control (1) (2) (3) (4) (5) (6) (7) (1) POWER button (P52, P71) Turns the projector on or off. (2) INPUT button (P55) Switches the input signal. (3) LENS button (P59) Each time the button is pressed, the adjustment window changes, from
  • Canon REALiS 4K600STZ | User Manual - Page 30
    standby mode. Otherwise, flashes in the following situations. • As the projector transitions from projection to standby • While the light source is off in . • LIGHT (orange) : Lights up or flashes when a problem occurs with the light source. • TEMP (red) : Lights up or flashes when
  • Canon REALiS 4K600STZ | User Manual - Page 31
    is on; LED indicator POWER STAND BY WARNING LIGHT (green) (red) (red) (orange) : Off TEMP (red) : Lit : Flashing Operating status Projector not plugged in. In standby mode. Resuming operation (projection) after standby. Cooling down while entering standby or power management mode from power
  • Canon REALiS 4K600STZ | User Manual - Page 32
    monitor output from a computer. Receives digital PC signal (Digital PC). (4) Service port (CONTROL) (P205) Used for executing user commands (P206 - (P135) Connects the LAN cable (shielded twisted pair). Used to connect the projector to a network. (6) USB port (P134) Connects a USB flash drive. Used
  • Canon REALiS 4K600STZ | User Manual - Page 33
    Before Use Remote Control (11) (1) (12) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) POWER button (P52, P71) Turns the projector on or off. (2) ASPECT button (P64, P93) Changes the aspect ratio mode. (3) Pointer buttons (P77) Selects the upper, lower, left or right item in the
  • Canon REALiS 4K600STZ | User Manual - Page 34
    blacks out the image. (23) FREEZE button (P72) Freezes the projected image. (24) Terminal for wired remote control (P36) Connects the remote control to the projector, for remote control operation. (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) 34
  • Canon REALiS 4K600STZ | User Manual - Page 35
    the remote control notch (1) and push the battery cover down (2). (1) (2) • If buttons on the remote control are inoperative when you attempt to operate the projector, replace the batteries with new ones. • Do not drop the remote control or subject it to impact. • Do not spill any liquids on the
  • Canon REALiS 4K600STZ | User Manual - Page 36
    ■ Remote Control Operating Range The remote control is an infrared type. Point it at the infrared remote receiver on the front or rear of the projector to operate it. 25° 25° 8 m (26.3') 8 m (26.3') 25° 25° • Use the remote control within an angle of 25° in any direction from directly in front
  • Canon REALiS 4K600STZ | User Manual - Page 37
    Advanced Guide Basic Guide Safety Instructions Before Use Installation Procedure Connection Procedure Projection Procedure Convenient Features Using Menus Menu Configuration Menu Settings Using the Projector on a Network Advanced Projection Maintenance Product Specifications Troubleshooting
  • Canon REALiS 4K600STZ | User Manual - Page 38
    screens. For best results, use a matte screen with a wide viewing angle. Screen Optical axis ■ Floor Installation To adjust the projection position when the projector is installed on the floor, use the lens shift function (P42, P62) to adjust the image up / down / left / right. For information
  • Canon REALiS 4K600STZ | User Manual - Page 39
    Guide Installation Procedure Installation Procedure ■ Installation on High Surfaces Using the lens shift function (P42), you can project images toward a lower level. When setting the projector on a high surface for projection, make sure the surface is flat and stable, and install the projector
  • Canon REALiS 4K600STZ | User Manual - Page 40
    zoom position (check specifications for details on the range in focus). Refer to the following table and decide the distance between the projector and screen. Image Size (diagonal) Height Width Relationship between image size and projecting distance (reference values) Image Size (Dia.) 40 60 80
  • Canon REALiS 4K600STZ | User Manual - Page 41
    Basic Guide Installation Procedure Installation Procedure Image Size (Dia.) 300 350 400 450 500 550 600 4096 x 2160 4096 x 2400 Image Size [cm (in)] Projection distance [m (feet)]
  • Canon REALiS 4K600STZ | User Manual - Page 42
    control, which moves the lens up, down, left, or right. For instructions, refer to "Adjusting the Image Position" (P62). ■ Amount of percentage relative to the image height and width. The lens shift ranges for the projector are as follows. A (Amount of vertical shift) B (Amount of horizontal shift
  • Canon REALiS 4K600STZ | User Manual - Page 43
    Basic Guide Installation Procedure Installation Procedure Maximum vertical (A) and horizontal (B) values are the approximate vertical lens shift distance from the central image position within the supported lens shift range. • (B) values are the approximate horizontal lens shift distance from the
  • Canon REALiS 4K600STZ | User Manual - Page 44
    Connection Procedure Before connecting the projector to other equipment, turn off both the projector and the other equipment. For instructions on connecting multiple sources of input for 4K projection, refer to "4K Projection" (P46). Connecting a Computer Computer AUDIO output terminal HDMI
  • Canon REALiS 4K600STZ | User Manual - Page 45
    Basic Guide Connection Procedure Connecting AV Equipment AV equipment HDMI terminal Connection Procedure Trigger terminal HDMI cable (not included) HDMI terminal AUDIO OUT terminal Audio cable (not
  • Canon REALiS 4K600STZ | User Manual - Page 46
    2160 4096 x 2400 The projector supports input signals at resolutions up to the maximum 4K resolution of 4096 x 2400. For details, check the table of supported signals. (P198) ■ 4K Digital Signal Compatibility The projector is equipped with DVI-D and HDMI: 2 (4K / Deep Color / HDCP 2.2*1) inputs
  • Canon REALiS 4K600STZ | User Manual - Page 47
    Basic Guide Connection Procedure Connection Procedure Resolution Frequency Subsampling Color depth HDMI 1.4 (10.2 to display devices such as projectors. HDCP specifications are established and managed by Digital Content Protection, LLC. *2 Use an HDMI cable supporting 18 Gbps. ■ Multi Input
  • Canon REALiS 4K600STZ | User Manual - Page 48
    combined to form a single image. Connect desktop computers by using two HDMI cables • Split-screen or four-quadrant projection is not supported when the projector is connected to multiple devices. • A single image cannot be projected by using two HDMI 2.0 cables with 4096 x 2160 signals (vertical
  • Canon REALiS 4K600STZ | User Manual - Page 49
    Basic Guide Connection Procedure Connection Procedure ■ Settings for Multi Input Mode Select layout. • [1x4] setting Supports many specialized signals using four input terminals, for projection side by side. For instructions on turning the projector on, see "Step 1 Turn the Projector On" (P52). 1 In
  • Canon REALiS 4K600STZ | User Manual - Page 50
    to computers the model name and setting values of connected display devices) is a list that consists of video signals used with one or multiple projector terminals. On the video output equipment, you can specify video signals for use with a different number of terminals. [Multi input mode select
  • Canon REALiS 4K600STZ | User Manual - Page 51
    Basic Guide Connection Procedure Connection Procedure Plugging the Projector In Connect the power cord to the projector and plug it in. • Unplug the power cord when the projector is not in use for an extended period. • [Date and time settings] may be reset if the projector is left unplugged for an
  • Canon REALiS 4K600STZ | User Manual - Page 52
    Projection Procedure Step 1 Turn the Projector On 1 Check the connection between the projector and the computer or AV equipment. (P44, P45) For instructions on connecting the power cord, refer to "Plugging the Projector In" (P51). 2 Press the POWER button. The [POWER] indicator initially flashes
  • Canon REALiS 4K600STZ | User Manual - Page 53
    Basic Guide Projection Procedure Projection Procedure ■ When the Language Selection Screen Appears A screen appears when the projector is turned on for the first time. You can select a language to be used by the projector for displaying menus and messages in the window. Select the desired
  • Canon REALiS 4K600STZ | User Manual - Page 54
    . • The function key you use and the method used to turn on the external monitor output vary depending on the model. For details, see the manual for your notebook computer. • With Windows 10, Windows 8.1, Windows 8 or Windows 7, you can turn on image output by holding down the Windows logo key and
  • Canon REALiS 4K600STZ | User Manual - Page 55
    Basic Guide Projection Procedure Projection Procedure Step 2 Select an Input Signal Select the last projection. 1 Press the INPUT button to display the window shown below. Remote control Projector The currently active input signal is marked with a green circle and enclosed by a orange border
  • Canon REALiS 4K600STZ | User Manual - Page 56
    signals (specifically, the DIGITAL or HDMI button). • Using the projector's multi-input feature, you can supply a single image via two or four cables. As sources of input for projection at 4K or other resolutions, choose from [DVI 1x2], [DVI 2x2], [DVI 1x4], or
  • Canon REALiS 4K600STZ | User Manual - Page 57
    Basic Guide Projection Procedure Step 3 Adjust the Image Projection Procedure Setting the Display Resolution of the Computer Based on the maximum resolution of the projector, set the display resolution of the computer to the resolution closest to the output signal resolution of the projector. (
  • Canon REALiS 4K600STZ | User Manual - Page 58
    Personalization] - [Adjust screen resolution] in the [Control Panel Home]. 2 Select the resolution closest to the maximum output signal resolution of the projector from the [Resolution] list. 3 Click the [OK] button. ■ Mac OS X 1 Open the Apple Menu and select [System Preferences]. 2 In the [System
  • Canon REALiS 4K600STZ | User Manual - Page 59
    Basic Guide Projection Procedure Projection Procedure Focusing, Resizing, or Moving the Image ■ Adjusting Image Focus To adjust the focus, press the FOCUS button on the remote control or the LENS button on the projector. 1 Press either the FOCUS button on the remote control or the LENS button on
  • Canon REALiS 4K600STZ | User Manual - Page 60
    The size of the projected image can be adjusted by pressing the ZOOM button on the remote control or the LENS button on the projector. Change the projector installation position if your desired image is too large or too small to adjust it with the zoom function. (P38) 1 Press the ZOOM button
  • Canon REALiS 4K600STZ | User Manual - Page 61
    2 Press the pointer buttons to adjust the image size. Remote control Projector Screen To enlarge the image, use the [ ] button on the remote control or projector. To reduce the image, use the [ ] button on the remote control or projector. 3 When the desired image size is selected, press the OK
  • Canon REALiS 4K600STZ | User Manual - Page 62
    the SHIFT button on the remote control or the LENS button on the projector. It can change the projected screen to the most suitable position by moving adjustment window. Remote control Press the LENS button on the projector repeatedly to switch between windows for parameters adjusted by controlling
  • Canon REALiS 4K600STZ | User Manual - Page 63
    Basic Guide Projection Procedure 2 Press the pointer buttons to adjust. Remote control Projector Projection Procedure Screen To raise or lower the image, use the [ ] / [ ] buttons on the remote control or projector. To move the image left or right, use the [ ] / [ ] buttons on the remote
  • Canon REALiS 4K600STZ | User Manual - Page 64
    . ■ True size The image is projected with the original resolution of the input signal. Screens of computers with a lower display resolution than the projector are displayed smaller but clearer than in other aspect ratios. There may be some cases when this cannot be selected, depending on the input
  • Canon REALiS 4K600STZ | User Manual - Page 65
    Basic Guide Projection Procedure to adjust the position of each corner of the image. For instructions on switching keystone adjustment, refer to "Keystone" (P107). • distortion is excessive and cannot be fully corrected, straighten the projector so that it faces the screen directly. • Signals are
  • Canon REALiS 4K600STZ | User Manual - Page 66
    2 Press the pointer buttons to adjust the dimensions. Remote control Projector To correct top distortion, press the [ ] button. To Corner Adjustment 1 Press the KEYSTONE button on the remote control or projector to display the corner adjustment window. (When [Keystone] is set to [
  • Canon REALiS 4K600STZ | User Manual - Page 67
    Basic Guide Projection Procedure Projection Procedure 2 Press the pointer button of the corner for correction, and then press the OK button. Remote control Projector 3 Press the pointer buttons to adjust the corner. Remote control Projector 4 When you have finished correcting, press the OK
  • Canon REALiS 4K600STZ | User Manual - Page 68
    Projection Procedure Step 6 Select the Image Quality (Image Mode) You can select an image mode to suit the projected image. In each image mode, you can further adjust the brightness, contrast, sharpness, gamma, HDR range, color adjustment (P100), advanced adjustment (P100), light source mode (P104)
  • Canon REALiS 4K600STZ | User Manual - Page 69
    Basic Guide Projection Procedure Projection Procedure ■ Selecting an Image Mode Press the , it requires the grayscale tone correction using a luminance meter according to the environment. In this projector, there are 21 types of tone settings for various ambient lights. You can correct the tone
  • Canon REALiS 4K600STZ | User Manual - Page 70
    Projection Procedure ■ Switching the mode to the DICOM SIM Mode 1 Press the IMAGE button on the remote control until [DICOM SIM] is displayed or select [DICOM SIM] from [Image mode] in the [Image adjustment] menu. 2 Display test patterns by pressing the TEST PATTERN button on the remote control or
  • Canon REALiS 4K600STZ | User Manual - Page 71
    Basic Guide Projection Procedure Projection Procedure Step 7 Turn the Projector Off 1 Press the POWER button to display the window shown below. Remote control Projector 2 When this window is displayed, press the POWER button again to turn off the power. After you turn the projector off,
  • Canon REALiS 4K600STZ | User Manual - Page 72
    that would be distracting, or to pause playback of video or animation. Remote control Press the FREEZE button to freeze the moving image. The projector shows the following icon. Press the FREEZE button again to return to the original display. Screen • It is also cancelled when the input signal
  • Canon REALiS 4K600STZ | User Manual - Page 73
    Basic Guide Convenient Features Convenient Features Specifying Power-Saving Settings Set power- (P124) Automatically turns off the light source or the power after a certain period if the projector is idle without an input signal. • Power management duration (P125) Specify the period after which the
  • Canon REALiS 4K600STZ | User Manual - Page 74
    74
  • Canon REALiS 4K600STZ | User Manual - Page 75
    Advanced Guide Basic Guide Safety Instructions Before Use Installation Procedure Connection Procedure Projection Procedure Convenient Features Using Menus Menu Configuration Menu Settings Using the Projector on a Network Advanced Projection Maintenance Product Specifications Troubleshooting
  • Canon REALiS 4K600STZ | User Manual - Page 76
    . [Install settings] tab (P106) This setting is used when installing the projector. [System settings] tab (P117) You can set the operation of the projector. [Network settings] tab (P135) These settings are for when using the projector from a PC via a network. [Information] tab (P155) You can check
  • Canon REALiS 4K600STZ | User Manual - Page 77
    the [ ] / [ ] buttons to select a tab. Remote control Projector • If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to move the current selection to the top. 3 Press the [ ] / [ ] buttons to select an item. Remote control Projector Advanced Guide Using Menus 77
  • Canon REALiS 4K600STZ | User Manual - Page 78
    ) 1. Select [Register network password]. 2. Press the OK button to display a different screen. 3. Use the buttons or number buttons on the remote control to enter the projector network password. 78
  • Canon REALiS 4K600STZ | User Manual - Page 79
    Advanced Guide Using Menus Using Menus Selecting from a different screen (2) Example: Random noise reduction (P101) 1. Select [Advanced adjustment]. 2. Press the OK button to display a different screen. 3. Select [
  • Canon REALiS 4K600STZ | User Manual - Page 80
    Menu Configuration Input settings (P92) Aspect Auto* P93 True size Input level HDMI P93 Auto* Normal Expanded Super white HDMI P93 Off On* Color space HDMI P94 Auto* RGB YCbCr Progressive HDMI P94 Off Film/auto* Video 1 Video 2 25p/30p(PsF) Input signal details Input
  • Canon REALiS 4K600STZ | User Manual - Page 81
    Advanced Guide Menu Configuration Menu Configuration Create profile (Displayed when [Image mode] is not [User 1] - [User 3]) User 1 User 2 User 3 Save profile P99 (Displayed when [Image mode] is [
  • Canon REALiS 4K600STZ | User Manual - Page 82
    Menu Configuration MPEG noise reduction Dynamic gamma Dynamic contrast Colorimetry (1) HDR Mem. color correct 6-axis color adjust Fine-Tune Gamma (2) Light source mode Brightness level (3) Reset Off* Weak Middle Strong Off*1 Weak Middle Strong Off* Mode 1 Mode 2 Mode 3 Auto* BT.709 BT.2020 Auto
  • Canon REALiS 4K600STZ | User Manual - Page 83
    Advanced Guide Menu Configuration Install settings (P106) Positional lock Off* On Image flip H/V * Adjust Registration Off* Adjust Advanced registration Off* Adjust 5-point adjustment Off* Adjust Manual adjustment Reset Menu Configuration P107 P107 P107 P108 P108 P109 P110 * Factory default,
  • Canon REALiS 4K600STZ | User Manual - Page 84
    Menu Configuration High altitude Operating mode Marginal focus Edge blending Lens - Position Screen color Iris Test pattern Off* On Normal* Fixed brightness Long duration 1 Long duration 2 Off* On Reset Off* Adjust Left Right Top Bottom Color blending adjustment Black level adjustment Marker Reset
  • Canon REALiS 4K600STZ | User Manual - Page 85
    Screen when blank Projector on On screen Menu position Menu display time Menu rotation Guide Show input status Air filter warning display Overheat warning display Remote control/Side control Beep Key repeat Key lock Remote control channel Black* Blue Light source off User logo Skip Canon logo* User
  • Canon REALiS 4K600STZ | User Manual - Page 86
    Menu Configuration Audio in terminal select DVI-1 DVI-2 DVI-3 DVI-4 HDMI-1 HDMI-2 DVI 1x2 DVI 2x2 / 1x4 HDMI 1x2 Serial communication Power supply settings Standby power setting Quick startup Power management mode Power management duration Direct power on P123 Off Audio in* Off Audio in* Off
  • Canon REALiS 4K600STZ | User Manual - Page 87
    schedule Reset Copy schedule to different day P125 P126 P127 P128 P128 P128 P129 * Factory default, or state after [Factory defaults] is executed. 87 Advanced Guide Menu Configuration
  • Canon REALiS 4K600STZ | User Manual - Page 88
    Menu Configuration Special period 1 Special period 2 Special period 3 Special period 4 Special period 5 Calibration Gamma restore Adjust panel temperature Light source calibration Trigger out Off* On Edit Period Day of week Edit schedule Reset Copy schedule to different day Off* On Edit Period Day
  • Canon REALiS 4K600STZ | User Manual - Page 89
    Advanced Guide Menu Configuration Air filter counter Power counter Firmware Factory defaults Reset / IPv6 Off* On Detailed IPv6 address settings Link local Auto Manual Gateway Auto settings Off* On Manual settings IP address Prefix length Gateway address Network setting initialization Yes
  • Canon REALiS 4K600STZ | User Manual - Page 90
    Channel Signal strength MAC address Wi-Fi Protected Setup Manual settings Detailed IPv4 address settings IPv6 Detailed IPv6 address IP address Subnet mask Gateway address Off* On Link local Auto Manual Gateway Auto settings Off On* Manual settings IP address Prefix length Gateway address Yes / No Off
  • Canon REALiS 4K600STZ | User Manual - Page 91
    (wired) IPv4 IPv6 Link local Auto Manual Detailed information (wireless) IPv4 IPv6 Link local Auto Manual P153 P153 P154 Information (P155) Model name Input signal Firmware Serial no. Projector usage time IP address (wired) IP address (wireless) Projector name Comments System information ID The
  • Canon REALiS 4K600STZ | User Manual - Page 92
    Menu Settings Input settings This section describes settings for aspect ratio, etc. (When the input signal is HDMI-1) Menu Function Aspect Select an image aspect ratio. Input level Select the input level for HDMI signal. Super white Select super white mode for HDMI signal. Color space
  • Canon REALiS 4K600STZ | User Manual - Page 93
    select the [Aspect] settings. Advanced Guide Menu Settings Input level > [Input level is selected automatically. (Some equipment may not support this.) • If the HDMI output of the connected , refer to the user's manual for the equipment connected to the projector. Super white > [Input settings
  • Canon REALiS 4K600STZ | User Manual - Page 94
    . Option Auto RGB YCbCr Function Selects the optimal color format for input signals. Forces the projector to handle the input signal as an RGB signal. Forces the projector to handle the input signal as a color difference signal. Progressive > [Input settings] > [Progressive] Performs progressive
  • Canon REALiS 4K600STZ | User Manual - Page 95
    Advanced Guide Menu Settings Menu Settings Input signal details > [Input settings] > [Input signal details] Shows input signal details for each input terminal used, for the selected input
  • Canon REALiS 4K600STZ | User Manual - Page 96
    Settings HDR information > [Input settings] > [HDR information] When HDMI signals are supplied, shows the Dynamic Range and Mastering InfoFrame information. The projector determines and indicates whether HDMI signals are SDR or HDR. HDR HDMI signals have an area that includes color and luminance
  • Canon REALiS 4K600STZ | User Manual - Page 97
    quality settings such as brightness, contrast, and sharpness. Advanced Guide Menu Settings (When the input signal is HDMI-1) Menu Function * Adjust projection brightness as controlled by the drive current of the laser diode. P105 Reset Restore the current image quality settings to defaults
  • Canon REALiS 4K600STZ | User Manual - Page 98
    Somewhat dark; conforms to the sRGB standard DICOM SIM Medical or other monochrome images Conforms to DICOM Standard Part 14. However, the projector cannot be used in diagnosis or similar applications. User 1 - 3 Up to 3 user profiles can be stored for your selected image quality settings
  • Canon REALiS 4K600STZ | User Manual - Page 99
    Advanced Guide Menu Settings Menu Settings Create profile > [Image adjustment] > [Create profile] Save desired image quality settings in up to 3 user profiles. • The saved settings are [Brightness], [
  • Canon REALiS 4K600STZ | User Manual - Page 100
    Menu Settings Color adjustment > [Image adjustment] > [Color adjustment] Adjust color-related settings such as color level, color balance, and color temperature. (In image modes other than DICOM SIM.) Submenu Color level Color balance Color temperature R / G / B Gain R / G / B Offset Function
  • Canon REALiS 4K600STZ | User Manual - Page 101
    image noise. Option Off Weak Middle Strong Function Disables MPEG noise reduction. Specify one of three levels of intensity of the MPEG noise reduction. Advanced Guide Menu Settings 101
  • Canon REALiS 4K600STZ | User Manual - Page 102
    Menu Settings Dynamic gamma You can adjust the gradation representation of light and dark portions of an image automatically. Option Function Off Disable dynamic gamma adjustment. Weak Middle Specify one of three levels of dynamic gamma adjustment. Strong Dynamic contrast For dark images
  • Canon REALiS 4K600STZ | User Manual - Page 103
    adjustment. Adjust Reset Use the [ ] / [ ] buttons to select [ Hue], [ Saturation], or [ Brightness], and use the [ ] / [ ] buttons for adjustment. Returns all adjustment values to zero. Advanced Guide Menu Settings 103
  • Canon REALiS 4K600STZ | User Manual - Page 104
    Menu Settings Fine-Tune Gamma Adjust white, red, green, and blue gamma curves. Red, green, and blue can be adjusted separately. Adjustments to white are also applied to the three other colors. Note that adjusting any color will overwrite previous adjustments. Use the [ ] / [ ] buttons to select a
  • Canon REALiS 4K600STZ | User Manual - Page 105
    Brightness level > [Image adjustment] > [Brightness level] Control the laser diode to adjust the projection brightness. Use the [ ] / [ ] buttons to adjust the brightness. Menu Settings Advanced Guide Menu Settings [Brightness level] appears instead of [Light source mode] when the operating mode
  • Canon REALiS 4K600STZ | User Manual - Page 106
    Menu Settings Install settings Adjust projection to suit the screen or the type of images, or how the projector is installed. (When the input signal is HDMI-1) Menu Function Positional lock Operation of installation related functions can be prohibited. Image flip H/V Specify settings for
  • Canon REALiS 4K600STZ | User Manual - Page 107
    Advanced Guide Menu Settings Menu Settings Positional lock > [Install settings] > [Positional lock] projector is installed upside-down. • When mounting the projector on a ceiling, use the optional ceiling attachment (RSCL15) and ceiling-mount arm (RS-CL17). Contact the Canon Customer Support
  • Canon REALiS 4K600STZ | User Manual - Page 108
    Menu Settings Professional settings > [Install settings] > [Professional settings] Specify advanced installation settings. Panel drive mode Select the LCD panel vertical resolution to use. Option Function 4096x2160 Use a resolution of 4096 x 2160 lines. 4096x2400 Use a resolution of 4096 x
  • Canon REALiS 4K600STZ | User Manual - Page 109
    3840 x 2160 (4K) at 60 Hz, YCbCr 4:4:4. Select in case of incorrect video or audio output from the projector because the EDID is not read correctly by connected equipment when set to Wide bandwidth (4K60Hz). Even if this function is used, the list of supported video
  • Canon REALiS 4K600STZ | User Manual - Page 110
    relative to images from other projectors used at the same time, screen is possible by color and area. For detailed instructions, refer to "Advanced Registration to Adjust Projected Images" Advanced registration Submenu 5-point adjustment Manual adjustment Reset Function Off Disable adjustment
  • Canon REALiS 4K600STZ | User Manual - Page 111
    manual adjustment. • Any values you manual adjustment. For more precise correction after 5-point adjustment, perform manual adjustment. • Any manual installation. Laser diode projector continuously for 24 hours or more, or when turning the projector not executed, the projector will be unable
  • Canon REALiS 4K600STZ | User Manual - Page 112
    , which form a blending area, can be adjusted for a more seamless appearance. For detailed instructions, see "Projecting from Multiple Projectors at Once (Edge Blending)" (P183). [Off] Disable blending. [Adjust] Display the menu for blending area adjustment. Start marker End marker Blending
  • Canon REALiS 4K600STZ | User Manual - Page 113
    unwanted colors or discrepancies in the blending area. Individually adjust red, green, and blue to correct unwanted colors or discrepancies in the blending area. Advanced Guide Menu Settings 113
  • Canon REALiS 4K600STZ | User Manual - Page 114
    Menu Settings Submenu Black level adjustment Marker Reset Function Because black is lighter in the blending area than in other areas, you can adjust the black level outside the blending area to make this difference in brightness less noticeable. Left image Position of end marker (hidden) $#"
  • Canon REALiS 4K600STZ | User Manual - Page 115
    Menu Settings Lens - Position > [Install settings] > [Lens - Position] The projector can store information about the lens position. Up to three sets of lens information (including, focus greenboard. Select to fine-tune the gain and offset of red, blue, and green. Advanced Guide Menu Settings 115
  • Canon REALiS 4K600STZ | User Manual - Page 116
    Menu Settings Iris > [Install settings] > [Iris] Use this feature for projection emphasizing contrast over brightness. Submenu Open Close 1-3 Function Disables aperture adjustment. Specify the aperture value in a range of 1-3. The [Iris] setting does not affect power consumption. Test pattern
  • Canon REALiS 4K600STZ | User Manual - Page 117
    Menu Settings System settings Customize projector and remote control operation, beeping, and other details after startup, during standby, and in other situations. Advanced Guide Menu Settings (When the input signal is HDMI-1) Menu Function User screen settings Customize user screens shown at
  • Canon REALiS 4K600STZ | User Manual - Page 118
    is all black. Blue The screen is all blue. Light source off The light source is turned off. User logo The user logo is projected. Projector on Select a logo to project after startup until input signals can be projected. Option Function Skip A black screen is projected
  • Canon REALiS 4K600STZ | User Manual - Page 119
    -screen menus, help, and warning or precaution icons. Advanced Guide Menu Settings Menu position Reposition menu display. Choose from upper [Extended] 30 seconds 3 minutes 10 seconds 3 minutes The windows for manual adjustment or 5-point adjustment in RGB alignment, and for other settings such
  • Canon REALiS 4K600STZ | User Manual - Page 120
    after startup or when this setting is switched to [Auto]. • Menus are not rotated automatically in response to changes in projector orientation during projection. Guide As you use the projector, messages are shown as guidance to introduce features and operation. Option Function Off Hides the
  • Canon REALiS 4K600STZ | User Manual - Page 121
    which operations are available using buttons on the remote control or in the projector's side controls. Advanced Guide Menu Settings Beep You can select whether a beep sounds or not when you operate the projector. Option Function Off Disables the beep. On Enables the beep. The beep will
  • Canon REALiS 4K600STZ | User Manual - Page 122
    to hold down the OK button. In a moment, a beep will sound, and the controls will be unlocked. When you access this setting from the projector's side controls, [Main unit] is not available. Similarly, when you access the setting from the remote control, [Remote (wireless)] is not available. Remote
  • Canon REALiS 4K600STZ | User Manual - Page 123
    communication > [System settings] > [Serial communication] You can check setting values for the service port (CONTROL) used for serial communication. Option Baud rate Data bits Parity Function Modulation at startup, in standby, and when no signal is supplied. Advanced Guide Menu Settings 123
  • Canon REALiS 4K600STZ | User Manual - Page 124
    network functions are enabled, including the web screen and PJLink. Low-power All network functions are available even in standby mode. However, the projector may be less responsive than usual when some functions are initially used. • If [Low-power] is selected, some features may take a long time
  • Canon REALiS 4K600STZ | User Manual - Page 125
    signal when the projector is idle, the projector starts displaying a can turn on the projector by connecting the power cable turn the projector on. On You can turn on the projector by connecting and flickering may occur. • If setting the projector to [Strong] or [Weak] produces distracting
  • Canon REALiS 4K600STZ | User Manual - Page 126
    Menu Settings Language > [System settings] > [Language] Select the menu display language. Language English Russian German Dutch French Finnish Italian Norwegian Spanish Turkish Portuguese Polish Swedish Hungarian Czech Danish Arabic Chinese (Simplified) Chinese (Traditional) Korean
  • Canon REALiS 4K600STZ | User Manual - Page 127
    , reset the air filter counter, schedule operation, and access other settings and information. Advanced Guide Menu Settings Password settings Disables the projector unless the correct password is entered. Option Function Off The projector can be used even if no password is entered. On The
  • Canon REALiS 4K600STZ | User Manual - Page 128
    clock. Date display format Daylight saving time • The date/time display format is set in [Date display format]. • Settings may be reset if the projector is left unplugged for an extended period. Choose [Year/month/date], [Month/date/year], or [Date/month/year] as the date display format shown
  • Canon REALiS 4K600STZ | User Manual - Page 129
    is not available unless the SNTP server IP address has been set. Schedule Some projector tasks can be automated by scheduling them. As the timing of scheduled tasks, or one of five special period times that you set up. Advanced Guide Menu Settings The [Period] setting of a special period cannot be
  • Canon REALiS 4K600STZ | User Manual - Page 130
    Menu Settings Detailed schedule setting Option Off On Disable the schedule. Enable the schedule. Edit the schedule. ■ Default Function Edit 130
  • Canon REALiS 4K600STZ | User Manual - Page 131
    Menu Settings Advanced Guide Menu Settings Select a day in [Day of week], and select the times, operations, and parameters. Light source calibration can also be scheduled during your specified period, by selecting CALIBRATION. (For details, see page 132.) However, the projector must project
  • Canon REALiS 4K600STZ | User Manual - Page 132
    for changes in image quality from long-term use or differences in the environment of use. Submenu Function Restore the original gamma if, after the projector has been used for some time, you notice that tone curves have changed, or if neutral colors have become tinted. Gamma restore can only be
  • Canon REALiS 4K600STZ | User Manual - Page 133
    external device can be triggered by turning the projector on or off. Option Function Off No output screen or other external device in sync when the projector is turned on or off. Air filter counter This the total time that the projector has been connected to a power supply. This
  • Canon REALiS 4K600STZ | User Manual - Page 134
    before updating the firmware. Update the projector firmware as follows. 1. Download updated firmware from the Canon website and store it at the root directory on a USB flash drive. 2. Insert the USB flash drive in the USB port. 3. Follow the instructions shown to complete the update process
  • Canon REALiS 4K600STZ | User Manual - Page 135
    Connecting the projector to a network enables you to control the projector from a computer and receive notification of projector errors via following is an explanation of preparation on the computer side. Connection Methods The projector can be connected to a wired network with a LAN cable or to a
  • Canon REALiS 4K600STZ | User Manual - Page 136
    can be used as an access point for direct communication with wireless LAN-compatible computers. Up to five computers can be connected at once. Projector (in PJ AP mode) Wireless LAN-compatible computers The following network features are available in PJ AP mode. • Web features • User commands Other
  • Canon REALiS 4K600STZ | User Manual - Page 137
    Advanced Guide Menu Settings Menu Settings • The following network features are available in on the network. To set a projector IP address, follow the instructions in "Completing Computer Settings for a Network Connection" (P156) and use the web screen, or use projector TCP/IP settings. (P144, P149
  • Canon REALiS 4K600STZ | User Manual - Page 138
    where use of the wireless LAN function permitted. Canon assumes no responsibility whatsoever for problems, etc., that may arise from use of the wireless LAN function in countries and regions other than those listed. ■ Model Number 4K600STZ (including WLAN module model: CH9-1346) Complies with
  • Canon REALiS 4K600STZ | User Manual - Page 139
    Guide Menu Settings Menu Settings Statement on EC directive Canon Inc. tímto prohlašuje, že tento CH9-1346 je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Undertegnede Canon van richtlijn 1999/5/EG. Hawnhekk, Canon Inc., jiddikjara li dan CH9-1346
  • Canon REALiS 4K600STZ | User Manual - Page 140
    Menu Settings Completing Projector Settings Settings described in this section apply to wired and wireless network connections, setting a network password, and other aspects of networked projection. (When the input
  • Canon REALiS 4K600STZ | User Manual - Page 141
    You can set whether or not a password is required in order to change the projector network settings. Option Off On Function A network password is not used. A network the buttons or number buttons on the remote control to enter the projector network password. Advanced Guide Menu Settings 141
  • Canon REALiS 4K600STZ | User Manual - Page 142
    in PJ AP mode (P136) requesting that you check security key settings. Detailed settings (wired) > [Network settings] > [Detailed settings (wired)] Display and manually change the wired IP address, gateway address, and other settings. Available only when wired networking is [On]. Menu MAC address
  • Canon REALiS 4K600STZ | User Manual - Page 143
    Menu Settings Function Configure details of the projector's wired LAN (IPv4) function. Detailed IPv4). DHCP Option Function Off Disables the DHCP function. TCP/IP settings can be configured manually. Enables the DHCP function. Searches the DHCP server. It will no longer be On possible
  • Canon REALiS 4K600STZ | User Manual - Page 144
    subnetwork, or change [Network (wired/wireless)] to [On/Off] before entering the wired IP address again. IPv6 Option Off On Function Disables the projector's wired LAN (IPv6) function. Enables the projector's wired LAN (IPv6) function. [Detailed IPv6 address settings] is now available. 144
  • Canon REALiS 4K600STZ | User Manual - Page 145
    Menu Menu Settings Function Configure details of the projector's wired LAN (IPv6) function. Advanced Guide Menu Settings Detailed IPv6 address settings Submenu Link local Auto Manual Gateway Auto settings Function Link-local address of the wired LAN (IPv6). Automatic addresses (up to 5) of the
  • Canon REALiS 4K600STZ | User Manual - Page 146
    network settings are initialized. Settings configured from the projector menu • Network settings lock (P141) • Network (P144) - IPv6 (P144) - Detailed IPv6 address settings (P145) - Auto settings (P145) - Manual settings (P145) - IP address (wired LAN (IPv6)) (P145) - Prefix length (P145) - Gateway
  • Canon REALiS 4K600STZ | User Manual - Page 147
    manually change the wireless IP address, gateway address, and other settings. Available only when wireless networking is [On]. Advanced Guide projector. Select the method of connection in infrastructure mode. Submenu PBC PIN Function Connect in PBC (push-button) mode. Following the instructions
  • Canon REALiS 4K600STZ | User Manual - Page 148
    Menu Function Manually specify the projector's wireless settings. Submenu Mode Function Shows the wireless connection mode. (P136) A list of available access point SSIDs is displayed. You can find available access points nearby and change the name of the connection. Manual settings SSID
  • Canon REALiS 4K600STZ | User Manual - Page 149
    , subnet mask, or gateway address manually, because the IP address is acquired from the DHCP server. Configure the projector's wireless TCP/IP settings. TCP/ Advanced Guide Menu Settings IPv6 Option Off On Function Disables the projector's wireless LAN (IPv6) function. Enables the projector's
  • Canon REALiS 4K600STZ | User Manual - Page 150
    Menu Settings Menu Function Configure details of the projector's wireless LAN (IPv6) function. Detailed IPv6 address settings Submenu Link local Auto Manual Gateway Auto settings Function Link-local address of the wireless LAN (IPv6). Automatic addresses (up to 5) of the wireless LAN (IPv6).
  • Canon REALiS 4K600STZ | User Manual - Page 151
    - IPv6 (P149) - Detailed IPv6 address settings (P150) - Auto settings (P150) - Manual settings (P150) - IP address (wireless LAN (IPv6)) (P150) - Prefix length (P150 (P172) - Default gateway (P172) • [Mail] (P174) • [Mail auth] (P175) • [Projector info.] (P177) Advanced Guide Menu Settings 151
  • Canon REALiS 4K600STZ | User Manual - Page 152
    conforms to Class 1 as defined in PJLink standards established by the Japan Business Machine and Information System Industries Association (JBMIA). This projector supports all commands that are defined by PJLink Class 1, and has been verified as conforming to the PJLink standard Class 1 definition
  • Canon REALiS 4K600STZ | User Manual - Page 153
    [Network settings] > [Crestron RoomView] Crestron RoomView enables centralized management of multiple projectors over a network. Networked projectors can be remotely controlled to troubleshoot issues, or turn the projectors on or off. Specify whether to use Crestron RoomView. Option Function Off
  • Canon REALiS 4K600STZ | User Manual - Page 154
    of the wired LAN (IPv4). Link local Link-local IP address of the wired LAN (IPv6). Auto Automatic IP address of the wired LAN (IPv6). Manual Manual IP address of the wired LAN (IPv6). Detailed information (wireless) IPv4 IPv6 IP address of the wireless LAN (IPv4). Link local Link-local IP
  • Canon REALiS 4K600STZ | User Manual - Page 155
    Menu Settings Checking Projector Information You can check information about the signal types of the images projected and other information. Advanced Guide Menu Settings Menu Function Model name Shows the model name. Input signal Details of the input signal currently selected Information such
  • Canon REALiS 4K600STZ | User Manual - Page 156
    Using the Projector on a Network Completing Computer Settings for a Network Connection Specifying an IP Address Instructions for setting a computer's IP address (for wired connections or wireless connections) are as follows for each operating system. ■ Windows 10 1 Right-click the Start button (
  • Canon REALiS 4K600STZ | User Manual - Page 157
    etc). 7 Select [Use the following IP address] and set the IP address and subnet mask. The projector's own default IP address is "192.168.254.254" for wired connections and "192.168.253. Close] button in the [Ethernet Properties] window to close it. 157 Advanced Guide Using the Projector on a Network
  • Canon REALiS 4K600STZ | User Manual - Page 158
    settings (IP address, subnet mask, default gateway, etc). 6 Select [Use the following IP address] and set the IP address and subnet mask. The projector's own default IP address is "192.168.254.254" for wired connections and "192.168.253.254" for wireless connections. Specify a different IP address
  • Canon REALiS 4K600STZ | User Manual - Page 159
    server, and so on). 4 Create a new network environment and set the IP address and subnet mask. The projector's own default IP address is "192.168.254.254" for wired connections and "192.168.253.254" for based on the notes taken before the change. 159 Advanced Guide Using the Projector on a Network
  • Canon REALiS 4K600STZ | User Manual - Page 160
    address of the wired LAN (IPv4) MAC address of the wireless LAN IP address of the wireless LAN (IPv4) The power status of the projector Air filter operating time Error message (if an error has occurred) Temperature abnormality Light source abnormality Faulty air filter unit Faulty cooling fan Faulty
  • Canon REALiS 4K600STZ | User Manual - Page 161
    user name is "root" and the password is "system". The settings screen is displayed. Complete the network settings on this screen. To control the projector from the computer, click [Projector control]. (P181) ■ Network Setting 1 Select a function to set up from the settings screen menu. 161 Advanced
  • Canon REALiS 4K600STZ | User Manual - Page 162
    Using the Projector on a Network 2 Enter setting details in the fields shown (1), and then click [OK] (2). (1) (2) 3 A confirmation window appears. Check the contents and if they are correct, click [Apply]. 162
  • Canon REALiS 4K600STZ | User Manual - Page 163
    other than above, "Save completed" is displayed. Click [Back to top] to return to the top page of the web screen. Advanced Guide Using the Projector on a Network Setting a Password [Password] From [Password] in the settings screen, you can set a user name and password for web screen login
  • Canon REALiS 4K600STZ | User Manual - Page 164
    Using the Projector on a Network Setting the Date and Time [Date and time settings] From [Date and time settings] in the settings screen, you can set time settings
  • Canon REALiS 4K600STZ | User Manual - Page 165
    Using the Projector on a Network Day & Time Summer Time Item Explanation Factory default setting IPv4 SNTP Enter the IPv4 SNTP server 0.0.0.0 server time for daylight saving time in 1-byte numbers, in the range 00:00 to 23:59. 00:00 Advanced Guide Using the Projector on a Network 165
  • Canon REALiS 4K600STZ | User Manual - Page 166
    on a Network Setting a Scheduling [Schedule] From [Schedule] in the settings screen, you can automate some projector tasks by scheduling them. As the timing of scheduled operation, choose from [Usually], which is not during a certain period, or one of five special period
  • Canon REALiS 4K600STZ | User Manual - Page 167
    usual schedule or period schedule selected in [Schedule view]. Green vertical line: projector on; gray vertical line: projector off; blue vertical line: switch input signals. Up to 8 schedules can edit the schedule of the selected day or time. Advanced Guide Using the Projector on a Network 167
  • Canon REALiS 4K600STZ | User Manual - Page 168
    Using the Projector on a Network Edit schedule Item Day Time Operation Parameter Explanation Shows the day of the week for the selected schedule. Enter the automatic execution time
  • Canon REALiS 4K600STZ | User Manual - Page 169
    the [Schedule copy] screen, enabling you to copy a schedule to any day for the selected usual schedule or period schedule. Advanced Guide Using the Projector on a Network Schedule copy Item Copy origin Registration Events Copy to day Explanation Factory default setting Select the day to copy
  • Canon REALiS 4K600STZ | User Manual - Page 170
    or off for wired LAN (IPv4). The following settings cannot be configured manually when this setting is [ON], because the IP address is acquired from the DHCP server. [IP address] [Subnet mask] [Default gateway] Enter the projector's wired LAN (IPv4) IP address in 1byte numbers. Enter the wired LAN
  • Canon REALiS 4K600STZ | User Manual - Page 171
    Using the Projector on a Network IPv6 address Item Explanation IPv6 Specify on or off for the IPv6 function of the wired LAN (IPv6). If the network subnet mask was changed, select [Subnet mask] in the above screen and set the new subnet mask. Advanced Guide Using the Projector on a Network 171
  • Canon REALiS 4K600STZ | User Manual - Page 172
    off for wireless LAN (IPv4). The following settings cannot be configured manually when this setting is [ON], because the IP address is acquired the DHCP server. [IP address] [Subnet mask] [Default gateway] Enter the projector's wireless LAN (IPv4) IP address in 1byte numbers. Enter the wireless LAN
  • Canon REALiS 4K600STZ | User Manual - Page 173
    the Projector on a simple method of establishing a wireless connection. None (Manual) Mode Select the wireless connection mode. infrastructure mode Select Channel Shows the wireless channel 1 number. When [Mode] is set to projector access point (PJ AP) mode, a channel can be selected. Key ID
  • Canon REALiS 4K600STZ | User Manual - Page 174
    Using the Projector on a Network Wireless setting Item Key Explanation Enter the wireless security key. Factory default setting
  • Canon REALiS 4K600STZ | User Manual - Page 175
    Using the Projector on a Network Item Explanation Factory default setting IPv6 SMTP server IP address Enter the SMTP server numbers (0 - 9999 milliseconds). Factory default setting OFF 0.0.0.0 110 110 300 Advanced Guide Using the Projector on a Network 175
  • Canon REALiS 4K600STZ | User Manual - Page 176
    the bottom of the screen. SNMP Settings [SNMP] From [SNMP] in the settings screen, you can configure the settings related to control of projectors which use SNMP (Simple Network Management Protocol). For the setting procedure, refer to "Network Setting" (P161). Item SNMP Receive community Password
  • Canon REALiS 4K600STZ | User Manual - Page 177
    and symbols (1 - 63 characters). Enter any relevant notes, such as where the projector is installed. Factory default setting Canon Projector001 Some characters such as # cannot be used for [Projector name] and [Comment]. Setting PJLink [PJLink] From [PJLink] in the settings screen
  • Canon REALiS 4K600STZ | User Manual - Page 178
    Using the Projector on a Network Item PJLink PJLink authentication Password Confirm password Explanation Turn the PJLink function on or off. If OFF is selected, the PJLink function will
  • Canon REALiS 4K600STZ | User Manual - Page 179
    Using the Projector on a Network Error System failed to connect SMTP server. System failed to connect POP3 server. System doesn't support this auth type. System Click [Initialize network settings]. 3 A confirmation window appears. Click [OK]. Advanced Guide Using the Projector on a Network 179
  • Canon REALiS 4K600STZ | User Manual - Page 180
    Text Error name Text Error name Text Temperature abnormality The internal temperature of the projector is abnormally high, or else the ambient air temperature exceeds the threshold. If the problem is with the projector, verify that it is properly installed and is being used correctly, and let the
  • Canon REALiS 4K600STZ | User Manual - Page 181
    recommended that you change the user name and password. (P163) The projector control screen appears. Advanced Guide Using the Projector on a Network The projector can be controlled from this screen. Item Projector name Comment Refresh Power Input Aspect Image mode Blank Explanation The name of
  • Canon REALiS 4K600STZ | User Manual - Page 182
    Using the Projector on a Network Item Mute Information Explanation Switches the mute setting on or off. (P34) Shows the results of control, or control error information, at the top of the screen. 5 When the operations are finished, click [Back to top] to return the initial web screen. 182
  • Canon REALiS 4K600STZ | User Manual - Page 183
    projectors used together can be adjusted to make them blend in better. ■ Basic Instructions Follow these steps when using two projectors Values indicated for this blending area are adjusted to match manually entered blending area values. Shading is applied to this area Guide Advanced Projection
  • Canon REALiS 4K600STZ | User Manual - Page 184
    and [Blue] values individually. 3 Repeat this adjustment on all projectors. ■ Black Level Adjustment In overlapping projection, dark colors are are identified in the context of end markers: A, B, and C. In the following instructions, only area D is adjusted, and the widths of A, B, and C are left
  • Canon REALiS 4K600STZ | User Manual - Page 185
    blending area and area D match. Advanced Guide Advanced Projection Adjust [D-area base] to needed. 4 Repeat this adjustment on all projectors. ■ Smoother Overlapping Areas The black level to suit these blending areas. In this example, instructions are given for adjusting area B. 1 In the
  • Canon REALiS 4K600STZ | User Manual - Page 186
    Advanced Projection 3 Select [B-width], and then specify the width of area B. Adjust the width of area B so that it roughly matches the area where the black level of area B stands out. This will make the width of area D narrower. 4 Select [Adjustment type] > [Black level]. Adjust [B-area base] as
  • Canon REALiS 4K600STZ | User Manual - Page 187
    points in the corners and center of the screen) and more precise manual adjustment based on 54 points (in a 6 x 9 grid). Any registration] > [Adjust] > [5-point adjustment] > [Adjust]. The projector enters 5-point adjustment mode, and a chart is displayed. • Charts Guide Advanced Projection
  • Canon REALiS 4K600STZ | User Manual - Page 188
    Advanced Projection 2 Use the buttons to select the point for correction, and then press the OK button. The projector enters color selection mode. Press the MENU button to return to [Advanced registration]. 3 Select [Red] or [Blue] as the color, and then press the OK
  • Canon REALiS 4K600STZ | User Manual - Page 189
    Manual Registration Use manual adjustment to correct registration only in certain areas. Any manual Advanced registration] > [Adjust] > [Manual adjustment]. The projector enters manual adjustment mode, and a chart is button. The projector enters color selection mode. Press the MENU button
  • Canon REALiS 4K600STZ | User Manual - Page 190
    OK button. • Each time you select [Chart] and press the OK button, display switches between the chart and the source signal. • Accessing the manual adjustment window during test pattern projection will show the test pattern instead of your supplied signal. 4 Use the buttons to align the adjustment
  • Canon REALiS 4K600STZ | User Manual - Page 191
    press the FOCUS button on the remote control or the LENS button on the projector. 1 Press the FOCUS button on the remote control twice to display the marginal control Press twice. Pressing the LENS button on the projector repeatedly switches between windows for lens-related parameters. Press the
  • Canon REALiS 4K600STZ | User Manual - Page 192
    Off] will not reset the setting value for peripheral focus. ■ Using Trigger out If you connect a screen or other external device to the projector's trigger terminal (P32) and configure [System settings], [Trigger out], [Link with power] (P133), operation of the device can be triggered by turning the
  • Canon REALiS 4K600STZ | User Manual - Page 193
    Advanced Guide Basic Guide Safety Instructions Before Use Installation Procedure Connection Procedure Projection Procedure Convenient Features Using Menus Menu Configuration Menu Settings Using the Projector on a Network Advanced Projection Maintenance Product Specifications Troubleshooting
  • Canon REALiS 4K600STZ | User Manual - Page 194
    . • Never use volatile cleaning liquid or benzine, as these may damage the finish of the projector. • When using a chemical dust cloth, make sure to read the instructions thoroughly. • When cleaning the projector's lens, use a commonly available air blower or lens cleaning paper. The lens surface is
  • Canon REALiS 4K600STZ | User Manual - Page 195
    2 Pull out the filter cover by gripping the two tabs at the bottom and lifting. 3 Open the filter cover and remove it. Maintenance 4 Grasp the air filter by the handles and remove it. Other Information Maintenance 195
  • Canon REALiS 4K600STZ | User Manual - Page 196
    air filter in the projector. 6 Align the filter cover tab with the groove and close the filter cover. • Handle the air filter carefully. If damaged, the air filter will not work properly. • To purchase a replacement air filter (part no: RS-FL04), contact the Canon Customer Support Center or visit
  • Canon REALiS 4K600STZ | User Manual - Page 197
    Product Specifications Displayed Test Patterns To access the test pattern menu, from the [Install settings] menu, select [Test pattern] (P116) > [On], or press the TEST PATTERN button on the remote control. While the test pattern is displayed, you can use the [ ] / [ ] buttons to switch patterns.
  • Canon REALiS 4K600STZ | User Manual - Page 198
    Product Specifications Supported Signal Types The projector automatically projects input signals correctly from computers or AV equipment compatible with any of these signals. HDMI (single) 1 Signal resolution 640x480 720x480 720x576 800x600 1280x720
  • Canon REALiS 4K600STZ | User Manual - Page 199
    in the EDID. No information is provided in the EDID for fields that are blank, so the computer output format must be configured manually. HDMI 1x2 1 2 FP : Front porch SW : Sync width BP : Back porch Combined multi input resolution Resolution at each input terminal Horizontal frequency [kHz
  • Canon REALiS 4K600STZ | User Manual - Page 200
    in the EDID. No information is provided in the EDID for fields that are blank, so the computer output format must be configured manually. DVI 1x2 1 3 FP : Front porch SW : Sync width BP : Back porch Combined multi input resolution Resolution at each input terminal Horizontal frequency [kHz
  • Canon REALiS 4K600STZ | User Manual - Page 201
    for fields that are blank, so the computer output format must be configured manually. Active video Blanking interval FP SW BP Active video Video signal Sync signal set to [4096x2160]. *3 Only YCbCr 4:2:0 is supported when [HDMI-1(2) EDID] is set to [9Gbps]. (RGB, YCbCr 4:4:4, and YCbCr 4:2:2
  • Canon REALiS 4K600STZ | User Manual - Page 202
    Projector Model name Display system Optical system Effective display area Effective pixels Other characteristics Zoom Focus Lens shift Focal length F number 4K600STZ 22.3 mm F2.6 Light source Type Blue laser diode + yellow phosphor Image size and projection Supported input signals See "Supported
  • Canon REALiS 4K600STZ | User Manual - Page 203
    jack Mini jack Mini jack RS-232C USB HDMI (single) HDMI (1 x 2) DVI-D x 4 HDMI x 2 4K600STZ 640 x 480, 720 x 480, 720 x 576, 800 x 600, 1280 x 720, 1024 x 768, 1366 Information, User's Manual (CDROM) and Warranty Card Wireless connectivity Standards IEEE802.11b/g/n Supported channels 1 CH
  • Canon REALiS 4K600STZ | User Manual - Page 204
    to the characteristics of the LCD panel. * Using the projector continuously for an extended period of time may accelerate the 2.0 (W) x 1.1 (H) x 6.9 (D) in Weight 100 g / 3.5 oz ■ External View 4K600STZ 201 mm (7.9") 90 mm (3.5") 177 mm (7.0") 133 mm (5.2") 559 mm (22.0") 605 mm
  • Canon REALiS 4K600STZ | User Manual - Page 205
    ■ Service Port (CONTROL) Product Specifications Pin assignment Pin No. Signal 1 OPEN 2 RxD 3 TxD 4 OPEN 5 GND 6 OPEN 7 Internal pull-up 8 OPEN 9 OPEN Communication format Communication mode : RS-
  • Canon REALiS 4K600STZ | User Manual - Page 206
    Product Specifications Main user commands Commands Power on Power supply Power off Power status acquisition HDMI-1 HDMI-2 HDMI 1x2 DVI-1 DVI-2 Input source DVI-3 DVI-4 DVI 1x2 DVI 2x2 DVI 1x4 Input source acquisition Standard Presentation Photo/sRGB DICOM SIM Image Mode Dynamic Video User 1
  • Canon REALiS 4K600STZ | User Manual - Page 207
    Product Specifications Commands ASCII representation Brightness acquisition GET=BRI Sharpness Sharpness value setting SHARP= Sharpness acquisition GET=SHARP Contrast Contrast value setting CONT= Contrast acquisition GET=CONT Aspect Auto True size
  • Canon REALiS 4K600STZ | User Manual - Page 208
    Troubleshooting LED Indicator Details When there is a problem with the projector, the LED indicator on the side of the projector illuminates or flashes continuously after the projector air filter correctly and restart the projector. Contact the Canon Customer Support Center if the same warning
  • Canon REALiS 4K600STZ | User Manual - Page 209
    . Remove any obstacle that is blocking the air intake or exhaust vent and contact the Canon Customer Support Center. Check whether the air filter is installed correctly. (P194) Check that Key lock (P121) is not enabled for the projector or the remote control. ■ You Cannot Project an Image from the
  • Canon REALiS 4K600STZ | User Manual - Page 210
    Troubleshooting Cause The BLANK function has been selected. No image is projected due to a problem with the computer. The depending on the model of notebook computer. For more detailed information, refer to the manual that came with your computer. Check whether the dual screen (multi-display) mode
  • Canon REALiS 4K600STZ | User Manual - Page 211
    is automatically turned off to protect the projector. (The [WARNING] indicator and [TEMP] indicator are lit.) Wait until the projector temperature drops, then make sure that the intake and exhaust vents (P28) are not blocked and turn on the projector. (P52) Other Information Troubleshooting 211
  • Canon REALiS 4K600STZ | User Manual - Page 212
    PJ AP mode, try changing the wireless channel on the projector (P147 - P148). In infrastructure mode, try changing the wireless channel on the access point. If connection is still not possible, contact the Canon Customer Support Center. ■ You Cannot Operate the Remote Control Cause Batteries are
  • Canon REALiS 4K600STZ | User Manual - Page 213
    Troubleshooting Cause You are operating the remote control in an unsuitable operating environment. The channel setting of the remote control does not match the setting of the projector. The key lock function is preventing operation of the remote control. Countermeasure Check whether the infrared
  • Canon REALiS 4K600STZ | User Manual - Page 214
    Index Numerics G 6-axis color adjust 103 Gamma 99 A Adjusting keystone distortion 65 Air filter 28, 194 Ambient light 101 AMX Device Discovery 153 ASPECT 64 Aspect 64 AUDIO IN terminal 32 AUDIO OUT terminal 32 Auto (Aspect 64 B BLANK 72 Brightness 99 C Ceiling mounted 39, 107
  • Canon REALiS 4K600STZ | User Manual - Page 215
    Wired Networks 142 Wireless Networks .......... 136, 142, 147 P Password 127, 128 PJLink 152, 177 POWER 52, 71 Projecting from Multiple Projectors at Once (Edge Blending 183 Projector on 118 R Rear projection 39, 107 Remote control 33, 34, 35, 122 Reset 67, 105, 134 S Screen color 115
  • Canon REALiS 4K600STZ | User Manual - Page 216
    * • Air filter Part No.: RS-FL04 • Remote control Part No.: RS-RC05 • Remote control Part No.: RS-RC04 * Use the above materials to hang the projector from the ceiling. * For ceiling mounting, both ceiling attachment (RS-CL15) and ceiling-mount arm (RS-CL17) are required. 216
  • Canon REALiS 4K600STZ | User Manual - Page 217
    INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A. INC. One Canon Park, Melville, New York 11747, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANON EUROPE LTD. 3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET United
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Connection Procedure
Projection Procedure
Convenient Features
Advanced Guide
Using Menus
Menu Configuration
Menu Settings
Using the Projector on a
Network
Advanced Projection
Other Information
Maintenance
Product Specifications
Troubleshooting
ENG
MULTIMEDIA PROJECTOR
User’s Manual