Canon REALiS LCOS 4K500ST User Manual

Canon REALiS LCOS 4K500ST Manual

Get Canon REALiS LCOS 4K500ST PDF manuals and user guides View all Canon REALiS LCOS 4K500ST manuals
Add to My Manuals
Save this manual to your list of manuals

Canon REALiS LCOS 4K500ST manual content summary:

  • Canon REALiS LCOS 4K500ST | User Manual - Page 1
    MULTIMEDIA PROJECTOR User's Manual Other Information Advanced Guide Basic Guide Safety Instructions Before Use Installation Procedure Connection Procedure Projection Procedure Convenient Features Using Menus Menu Settings Advanced Projection Maintenance Product Specifications Troubleshooting ENG
  • Canon REALiS LCOS 4K500ST | User Manual - Page 2
    to a network are given in the "Advanced Guide" section. Read this manual thoroughly to make the most of your projector. Installation of the projector should be performed by a qualified technician, if possible. Contact the Canon Customer Support Center for further information. Symbols of Button
  • Canon REALiS LCOS 4K500ST | User Manual - Page 3
    Table of Contents How to Use This Manual 2 Projector Highlights 4 Safety Instructions 5 Precautions for Use 12 Installation and Handling Precautions 13 Precautions on the Lamp 14 Precautions for the Batteries of the Remote Control 15 For Safe
  • Canon REALiS LCOS 4K500ST | User Manual - Page 4
    Projector Highlights 4K Projection Using 4096 x 2400 LCOS Panels Outstanding projection resolution of up to 4096 x 2400 is possible, using three 0.76 inch liquid crystal on silicon (LCOS) panels in conjunction with dual highperformance image processors and a new 4K-compatible wide zoom lens. Bright
  • Canon REALiS LCOS 4K500ST | User Manual - Page 5
    accidents. If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in the back of this manual. If the problem still persists, contact the Canon Customer Support Center. CAUTION
  • Canon REALiS LCOS 4K500ST | User Manual - Page 6
    cm (1.6') 50 cm (1.6') • Do not cover the ventilation slots on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous. • If the projector is unused for an extended time, unplug the projector from the power outlet. • Do not project the same image for
  • Canon REALiS LCOS 4K500ST | User Manual - Page 7
    ■ READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. All the safety and operating instructions should be read before beginning to operate the product. Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Do not
  • Canon REALiS LCOS 4K500ST | User Manual - Page 8
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally after following the operating instructions
  • Canon REALiS LCOS 4K500ST | User Manual - Page 9
    Safety Instructions Safety Instructions AC Power Cord Requirement The AC Power Cord supplied with this projector meets the requirements for use in the country you purchased office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www
  • Canon REALiS LCOS 4K500ST | User Manual - Page 10
    Instructions Federal Communication Commission Notice Model: 4K500ST and used in accordance with the instruction manual, may cause harmful interference to radio adequate measures. The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class
  • Canon REALiS LCOS 4K500ST | User Manual - Page 11
    Safety Instructions Safety Instructions Safety Symbols in this Manual This section describes the safety symbols used in this manual. Important projector safety information is identified by the following symbols. Always observe the safety information by these symbols. Denotes the risk of death or
  • Canon REALiS LCOS 4K500ST | User Manual - Page 12
    plug from the power outlet and contact the Canon Customer Support Center. Failure to do so could cause a fire or result in an electric shock. • If smoke is emitted • If an unusual smell or noise is emitted • If water or other liquid has entered the projector • If metal or any other foreign material
  • Canon REALiS LCOS 4K500ST | User Manual - Page 13
    Safety Instructions Safety Instructions Pay attention to the following points regarding the power containing a liquid on top of the projector. • Do not touch the projector itself, the power cord, or the cable if lightening strikes. • Do not move the projector until you have switched off the power,
  • Canon REALiS LCOS 4K500ST | User Manual - Page 14
    or repair is required, contact the Canon Customer Support Center. • Do not disassemble or modify the projector (including consumable parts) or the remote refer to the installation manual included with the ceiling mount (sold separately). Precautions on the Lamp This projector uses a high-pressure
  • Canon REALiS LCOS 4K500ST | User Manual - Page 15
    , the lamp may have ruptured. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. • With ceiling-mounted projectors, the lamp may fall out when you open the lamp cover, or during replacement. During replacement, stand to the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 16
    Safety Instructions Pay attention to the following points regarding installation and handling of the projector. • If the projector during projection. Doing so could cause a fire. • Presenters in front of the projector should stand where the light does not seem too bright, and where their shadow does
  • Canon REALiS LCOS 4K500ST | User Manual - Page 17
    may shorten the lamp life or damage the lamp. For details, contact the Canon Customer Support Center. • Do not install the projector near high-voltage electrical power lines or an electrical power source. • Do not use the projector on a soft surface such as carpet or sponge mat, etc. Doing so could
  • Canon REALiS LCOS 4K500ST | User Manual - Page 18
    alone. Have at least one assistant. Precautions for Installation Be sure to read "Safety Instructions" and "For Safe Use" (P5 - P17). Also take the following precautions during installation. • Do not strike the projector or Air intake vent subject it to impact. Doing so may cause a malfunction
  • Canon REALiS LCOS 4K500ST | User Manual - Page 19
    projected to return to normal. ■ At Altitudes above 2,300 m (7,545.8'), Adjust the Settings Projector settings must be adjusted when using the projector at altitudes of 2,300 m (7,545.8') or higher. Specifically, refer to instructions for [High altitude] (P102) in the [Install settings] menu. 19
  • Canon REALiS LCOS 4K500ST | User Manual - Page 20
    Before Installation ■ When Using Mounted on the Ceiling When the projector is used mounted on the ceiling or installed in a high location, it is necessary to periodically clean the air intake and exhaust vents, and the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 21
    or downward projection, refer to instructions for [Vertical projection] (P102) in the [Install settings] menu. • Do not attempt to install the projector for upward or downward projection by yourself. Always request installation by a qualified technician or the Canon Customer Support Center. 10° 10
  • Canon REALiS LCOS 4K500ST | User Manual - Page 22
    projection]. (P102) • When mounting the projector on the ceiling, it is more convenient to install the projector right-side up, with the adjustable feet facing Ensure Network Security Take measures to ensure network security. Note that Canon is not liable in any way for direct or indirect loss from
  • Canon REALiS LCOS 4K500ST | User Manual - Page 23
    EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NO SUPPORT Canon Inc., and all its subsidiaries or its dealers do not make any support service regarding the source code. Canon Inc., and all its subsidiaries or its dealers shall not respond to any questions or
  • Canon REALiS LCOS 4K500ST | User Manual - Page 24
    ). However, some buttons are not supported with this projector. The RS-RC05 can also be used as a wired remote. (P33) • Power cord (1.8 m / 5.9') For Continental Europe (AA size x2) • Lens cap For the U.S.A. and Canada • Important Information • User's Manual
  • Canon REALiS LCOS 4K500ST | User Manual - Page 25
    Before Use Part Names Projector ■ Front Side Terminals and connectors (P29) Before Use LED indicators (P27) Projection lens Power cord connector (P59) Anti-theft lock hole An anti-theft wire
  • Canon REALiS LCOS 4K500ST | User Manual - Page 26
    Before Use Side Control (6) (2) (3) (1) (4) (5) (7) (1) POWER button (P60, P79) Turns the projector on or off. (2) INPUT button (P63) Switches the input signal. (3) LENS button (P67) Each time the button is pressed, the adjustment window changes, from focus (
  • Canon REALiS LCOS 4K500ST | User Manual - Page 27
    is on. • STAND BY (red) : Lights up or flashes during standby or when the projector is shutting down. • WARNING (red) : Lights up or flashes when an error occurs. • LAMP (orange) : Lights up or flashes when a problem occurs with the lamp or lamp cover. • TEMP (red) : Lights up or flashes
  • Canon REALiS LCOS 4K500ST | User Manual - Page 28
    is on; : Off LED indicator POWER STAND BY WARNING LAMP TEMP (green) (red) (red) (orange) (red) : Lit : Flashing Operating status A projector is not plugged in. In standby mode. Resuming operation (projection) after standby (flashes once). Cooling down while entering standby or power
  • Canon REALiS LCOS 4K500ST | User Manual - Page 29
    and audio signals across a single cable. (3) Service port (CONTROL) (P177) Used for executing user LAN cable (shielded twisted pair). Used to connect the projector to a network. (5) USB port (P119) Connects a P53, P54) Outputs the audio to external AV equipment. This outputs the audio signal that
  • Canon REALiS LCOS 4K500ST | User Manual - Page 30
    Before Use Remote Control The remote control allows you to operate all functions of the projector. (11) (1) (12) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) POWER button (P60, P79) Turns the projector on or off. (2) ASPECT button (P72, P88) Changes the aspect ratio mode. (3) Pointer buttons (P85)
  • Canon REALiS LCOS 4K500ST | User Manual - Page 31
    blacks out the image. (23) FREEZE button (P80) Freezes the projected image. Before Use (24) Terminal for wired remote control (P33) Connects a cable to the projector for remote control operation. (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) 31
  • Canon REALiS LCOS 4K500ST | User Manual - Page 32
    the remote control notch (1) and push the battery cover down (2). (1) (2) • If buttons on the remote control are inoperative when you attempt to operate the projector, replace the batteries with new ones. • Do not drop the remote control or subject it to impact. • Do not spill any liquids on the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 33
    ■ Remote Control Operating Range The remote control is an infrared type. Point it at the infrared remote receiver on the front or rear of the projector to operate it. 25° 25° 8 m (26.3') 8 m (26.3') 25° 25° • Use the remote control within an angle of 25° in any direction from directly in front
  • Canon REALiS LCOS 4K500ST | User Manual - Page 34
    34
  • Canon REALiS LCOS 4K500ST | User Manual - Page 35
    Basic Guide Other Information Advanced Guide Basic Guide Safety Instructions Before Use Installation Procedure Connection Procedure Projection Procedure Convenient Features Using Menus Menu Settings Advanced Projection Maintenance Product Specifications Troubleshooting 35
  • Canon REALiS LCOS 4K500ST | User Manual - Page 36
    drawn, and other steps taken to make the screen easier to see. Screen Optical axis ■ Floor Installation To adjust the projection position when the projector is installed on the floor, use the lens shift function (P51, P70) to adjust up / down / left / right. For information about the relationship
  • Canon REALiS LCOS 4K500ST | User Manual - Page 37
    Guide Installation Procedure Installation Procedure ■ Installation on High Surfaces Using the lens shift function (P51), you can project images toward a lower level. When setting the projector on a high surface for projection, make sure the surface is flat and stable, and install the projector
  • Canon REALiS LCOS 4K500ST | User Manual - Page 38
    in eye damage. • During projection, never put an object in front of the projector's lens. Make sure the followings when you install and handle the ceiling attachment. • Make sure to ask the Canon Customer Support Center if you want to install the ceiling attachment. An inappropriate installation may
  • Canon REALiS LCOS 4K500ST | User Manual - Page 39
    Basic Guide Installation Procedure Installation Procedure Parts Lineup ■ Parts Included with RS-CL15 sheet for a ceiling-mount hole: 2 shts. A B 4K500ST • M6 screw (25 mm/1.0") : 4 pcs. • Anti-fall wires: 2 pcs. Use the template sheet (B) for the projector. • M4 screw (15 mm/0.6") : 10 pcs. •
  • Canon REALiS LCOS 4K500ST | User Manual - Page 40
    the lens shift feature. • Before mounting the Ceiling Attachment, be sure to check the strength of the ceiling. The ceiling should be strong enough to support the projector and Ceiling Attachment (and optional extension pipe). If the ceiling is not strong enough, be sure to reinforce it. The
  • Canon REALiS LCOS 4K500ST | User Manual - Page 41
    Basic Guide Installation Procedure Installation Dimensions Installation Procedure Projection Distance Height 298 mm (11.7") 236 mm (9.3") 534 mm (21.0") Side view 279 mm (11.0") 263 mm (10.4")
  • Canon REALiS LCOS 4K500ST | User Manual - Page 42
    Installation Procedure Assembly and Installation ■ Installation to flat and level Ceiling Preparation: Separate the Joint fitting from the Ceiling-mount bracket temporarily Remove four M5 screws to separate Joint Direction to the screen fitting from the Ceiling-mount bracket. 1 Make a hole in
  • Canon REALiS LCOS 4K500ST | User Manual - Page 43
    Basic Guide Installation Procedure 3 Attach the Base bracket to the projector 1 Remove the four screws at each corner on top of the projector. 2 Install the attached M6 screws at the four screw fastening positions on the Base bracket. Attach the included toothed lock washer in the back-left
  • Canon REALiS LCOS 4K500ST | User Manual - Page 44
    the cables. • Be sure to secure screws (B) tightly after making the adjustment discussed in "Adjust the Projection Angle" (P48). 8 Connect cables Connect cables to the projector. After completion of installation, adjust the projection angle (P48). 44
  • Canon REALiS LCOS 4K500ST | User Manual - Page 45
    Basic Guide Installation Procedure Installation Procedure ■ Installation to a High Ceiling four M5 screws from the sides of the outer pipe, adjust the inner pipe length according to the projector installation height, and then secure the four M5 screws. • When attaching screws in step 2, insert
  • Canon REALiS LCOS 4K500ST | User Manual - Page 46
    Installation Procedure 6 Attach the top of the extension pipe to the Ceiling-mount bracket Secure to the extension pipe using the four supplied M5 screws. • The open end of the pipe should face the open end of the Ceilingmount bracket as shown. Direction to the screen 7 Attach the Joint fitting to
  • Canon REALiS LCOS 4K500ST | User Manual - Page 47
    Basic Guide Installation Procedure 8 Hook the Base bracket to the Joint fitting and secure it temporarily Hook the Base bracket on the protrusion cover of the pipe. Secure to the extension pipe using the supplied M3 screw. 4 Connect the cables to the projector. Installation Procedure A B 47
  • Canon REALiS LCOS 4K500ST | User Manual - Page 48
    angle. • After completion of adjustment, tighten the screws and check that every fitting is secured firmly. • Be sure to hold the projector from falling until the Ceiling-mount bracket and Base bracket are secured firmly. Adjust the horizontal projection angle. A Adjust the vertical projection
  • Canon REALiS LCOS 4K500ST | User Manual - Page 49
    Guide Installation Procedure ■ Adjust the screen inclination 1 Loosen four screws (D), and then adjust the slant angle of the projector. 2 When the projector the lamp by yourself. Always request service from the Canon Customer Support Center. • With ceiling-mounted projectors, the lamp may fall out
  • Canon REALiS LCOS 4K500ST | User Manual - Page 50
    of the image (P68), and the level of focus (P67). Refer to the following table and decide the distance between the projector and screen. Image Size (diagonal) Height Width 4K500ST Image Size (Dia.) 40 60 80 100 120 140 160 180 200 220 240 260 280 300 350 400 450 500 550
  • Canon REALiS LCOS 4K500ST | User Manual - Page 51
    lens up, down, left, or right. For instructions, refer to "Adjusting the Image Position" (P70). ■ Amount of Lens Shift The amount of lens shift is indicated as a percentage relative to the image height and width. The lens shift ranges for the projector are as follows. A (Amount of vertical shift
  • Canon REALiS LCOS 4K500ST | User Manual - Page 52
    Installation Procedure 4K500ST Maximum vertical (A) and horizontal (B) movement using lens shift values are the approximate vertical lens shift distance from the central image position within the supported lens shift range. • (B) values are the approximate horizontal lens shift distance from the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 53
    Basic Guide Connection Procedure Connection Procedure Before connecting the projector to other equipment, turn off both the projector and the other equipment. For instructions on connecting multiple sources of input for 4K projection, refer to "Multi Input 4K Projection" (P55). Connecting a
  • Canon REALiS LCOS 4K500ST | User Manual - Page 54
    Connection Procedure Connecting AV Equipment Amplified speakers Mini jack RCA terminal Audio cable (not included) Audio cable (not included) AUDIO OUT terminal HDMI terminal HDMI cable (not included) HDMI terminal AV equipment 54
  • Canon REALiS LCOS 4K500ST | User Manual - Page 55
    Basic Guide Connection Procedure Connection Procedure Multi Input 4K Projection ■ projector supports resolutions up to 4096 x 2400. For details, check the table of supported signals. (P169) 1920 x 1080 3840 x 2160 4096 x 2400 ■ 4K Support Using Digital Signals and Multiple Inputs The projector
  • Canon REALiS LCOS 4K500ST | User Manual - Page 56
    's video output (whether dual-link compatible DVI-D or HDMI) support split-screen display or display in four quadrants. To connect the projector to computers, use up to four DVI cables and two HDMI project on two or four screens when the projector is connected to multiple computers or pieces of
  • Canon REALiS LCOS 4K500ST | User Manual - Page 57
    Basic Guide Connection Procedure Connection Procedure ■ Settings for Multi Input For details, check the table of supported signals. (P169) • [Normal] setting Supports many typical images, including [Single], [1x2], [2x2], and [1x4]. • [Single] setting Supports many specialized signals from a single
  • Canon REALiS LCOS 4K500ST | User Manual - Page 58
    to computers the model name and setting values of connected display devices) is a list that consists of video signals used with one or multiple projector terminals. On the video output equipment, you can specify video signals for use with a different number of terminals. [Multi input mode select
  • Canon REALiS LCOS 4K500ST | User Manual - Page 59
    Guide Connection Procedure Connection Procedure ■ 4K Projection Notes Colors may appear distorted when images are viewed from the side on some screens, but this does not indicate a problem with the projector. For best results, use a matte screen with a wide viewing angle. Plugging the Projector
  • Canon REALiS LCOS 4K500ST | User Manual - Page 60
    Projection Procedure Step 1 Turn the Projector On 1 Check the connection between the projector and the computer or AV equipment. (P53, P54) For instructions on connecting the power cord, refer to "Plugging the Projector In" (P59). 2 Press the POWER button. The [POWER] indicator initially flashes
  • Canon REALiS LCOS 4K500ST | User Manual - Page 61
    Basic Guide Projection Procedure Projection Procedure ■ When the Language Selection Screen Appears A screen appears when the projector is turned on for the first time. You can select a language to be used by the projector for displaying menus and messages in the window. Select the desired
  • Canon REALiS LCOS 4K500ST | User Manual - Page 62
    . • The function key you use and the method used to turn on the external monitor output vary depending on the model. For details, see the manual for your notebook computer. • With Windows 8.1, Windows 8 or Windows 7, you can turn on image output by holding down the Windows logo key and pressing the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 63
    inputs when multiple computers or multiple sets of AV equipment are connected. Skip this step if you have not changed the input signal since the last projection. 1 Press the INPUT button to display the window shown below. Remote control Projector The currently active input signal is marked with
  • Canon REALiS LCOS 4K500ST | User Manual - Page 64
    projection by pressing buttons on the remote control to switch input signals (specifically, the DIGITAL or HDMI button). • In multi input mode, the projector combines two or four sources of input for projection together. As sources of input for projection at 4K or other resolutions, choose from [DVI
  • Canon REALiS LCOS 4K500ST | User Manual - Page 65
    Basic Guide Projection Procedure Step 3 Adjust the Image Projection Procedure Setting the Display Resolution of the Computer Based on the maximum resolution of the projector, set the display resolution of the computer to the resolution closest to the output signal resolution of the projector. (
  • Canon REALiS LCOS 4K500ST | User Manual - Page 66
    Personalization] - [Adjust screen resolution] in the [Control Panel Home]. 2 Select the resolution closest to the maximum output signal resolution of the projector from the [Resolution] list. 3 Click the [OK] button. ■ Mac OS X 1 Open the Apple Menu and select [System Preferences]. 2 In the [System
  • Canon REALiS LCOS 4K500ST | User Manual - Page 67
    Basic Guide Projection Procedure Projection Procedure Focusing, Resizing, or Moving the Image ■ Adjusting Image Focus To adjust the focus, press the FOCUS button on the remote control or the LENS button on the projector. 1 Press either the FOCUS button on the remote control or the LENS button on
  • Canon REALiS LCOS 4K500ST | User Manual - Page 68
    The size of the projected image can be adjusted by pressing the ZOOM button on the remote control or the LENS button on the projector. Change the projector installation position if your desired image is too large or too small to adjust it with the zoom function. (P36) 1 Press the ZOOM button
  • Canon REALiS LCOS 4K500ST | User Manual - Page 69
    2 Press the pointer buttons to adjust the image size. Remote control Projector Screen To enlarge the image, use the [ ] button on the remote control or projector. To reduce the image, use the [ ] button on the remote control or projector. 3 When the desired image size is selected, press the OK
  • Canon REALiS LCOS 4K500ST | User Manual - Page 70
    the SHIFT button on the remote control or the LENS button on the projector. It can change the projected screen to the most suitable position by moving adjustment window. Remote control Press the LENS button on the projector repeatedly to switch between windows for parameters adjusted by controlling
  • Canon REALiS LCOS 4K500ST | User Manual - Page 71
    Basic Guide Projection Procedure 2 Press the pointer buttons to adjust. Remote control Projector Projection Procedure Screen To raise or lower the image, use the [ ] / [ ] buttons on the remote control or projector. To move the image left or right, use the [ ] / [ ] buttons on the remote
  • Canon REALiS LCOS 4K500ST | User Manual - Page 72
    to change the setting depending on the resolution of the computer or other AV equipment connected. Select the Aspect Select [Aspect] based on the input signal. Screens of computers with a lower display resolution than the projector are displayed smaller but clearer than in other aspect ratios. There
  • Canon REALiS LCOS 4K500ST | User Manual - Page 73
    Basic Guide Projection correction to adjust the position of each corner of the image. For instructions on switching keystone correction, refer to "Keystone" (P98). • distortion is excessive and cannot be fully corrected, straighten the projector so that it faces the screen directly. • Signals are
  • Canon REALiS LCOS 4K500ST | User Manual - Page 74
    2 Press the pointer buttons to adjust the dimensions. Remote control Projector To correct top distortion, press the [ ] button. To Corner Adjustment 1 Press the KEYSTONE button on the remote control or projector to display the corner adjustment window. (When [Keystone] is set to [
  • Canon REALiS LCOS 4K500ST | User Manual - Page 75
    Basic Guide Projection Procedure Projection Procedure 2 Press the pointer button of the corner for correction, and then press the OK button. Remote control Projector 3 Press the pointer buttons to adjust the corner. Remote control Projector 4 When you have finished correcting, press the OK
  • Canon REALiS LCOS 4K500ST | User Manual - Page 76
    Projection Procedure Step 6 Select the Image Quality (Image Mode) You can select an image mode to suit the projected image. In each image mode, you can further adjust the brightness (P92), contrast, sharpness, gamma, color adjustment (P93), advanced adjustment (P93), and lamp mode. (P96) Image
  • Canon REALiS LCOS 4K500ST | User Manual - Page 77
    Basic Guide Projection Procedure Projection Procedure ■ Selecting an Image Mode Press the , it requires the grayscale tone correction using a luminance meter according to the environment. In this projector, there are 21 types of tone settings for various ambient lights. You can correct the tone
  • Canon REALiS LCOS 4K500ST | User Manual - Page 78
    Projection Procedure ■ Switching the mode to the DICOM SIM Mode 1 Press the IMAGE button on the remote control until [DICOM SIM] is displayed or select [DICOM SIM] from [Image mode] in the [Image adjustment] menu. 2 Press the TEST PATTERN button on the remote control until [DICOM] is displayed or
  • Canon REALiS LCOS 4K500ST | User Manual - Page 79
    Basic Guide Projection Procedure Projection Procedure Step 7 Turn the Projector Off 1 Press the POWER button to display the window shown below. Remote control Projector 2 When this window is displayed, press the POWER button again to turn off the power. After you turn the projector off, the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 80
    that would be distracting, or to pause playback of video or animation. Remote control Press the FREEZE button to freeze the moving image. The projector shows the following icon. Press the FREEZE button again to return to the original display. Screen • It is also cancelled when the input signal
  • Canon REALiS LCOS 4K500ST | User Manual - Page 81
    Basic Guide Convenient Features Convenient Features Specifying Power-Saving Settings Set power input signal. • Power management duration (P114) Specify the period after which the lamp or the projector should go off automatically if left idle without an input signal when [Power management mode] is
  • Canon REALiS LCOS 4K500ST | User Manual - Page 82
    82
  • Canon REALiS LCOS 4K500ST | User Manual - Page 83
    Advanced Guide Other Information Advanced Guide Basic Guide Safety Instructions Before Use Installation Procedure Connection Procedure Projection Procedure Convenient Features Using Menus Menu Settings Advanced Projection Maintenance Product Specifications Troubleshooting 83
  • Canon REALiS LCOS 4K500ST | User Manual - Page 84
    [Install settings] tab (P97) This setting is used when installing the projector. [System settings] tab (P108) You can set the operation of the projector. [Network settings] tab (P123) These settings are for when using the projector from a PC via a network. For the network settings, refer to "Network
  • Canon REALiS LCOS 4K500ST | User Manual - Page 85
    Advanced Guide Using Menus Basic Menu Operations 1 Press the MENU button to display the menu window. Remote control Projector Using Menus 2 Press the [ ] / [ ] buttons to select a tab. Remote control Projector • If the tab position is not highlighted in orange, press the [ ] / [ ] buttons
  • Canon REALiS LCOS 4K500ST | User Manual - Page 86
    [Register network password]. A different screen is displayed. 2. Use the buttons or number buttons on the remote control to enter the projector network password. Selecting from a different screen (2) Example: Random noise reduction (P94) 1. Select [Advanced adjustment]. 2. Press the OK button to
  • Canon REALiS LCOS 4K500ST | User Manual - Page 87
    in cinematic content or moving images in videos. Menus that are not available are grayed out or hidden. Details P88 P88 P88 P89 P89 Advanced Guide Menu Settings 87
  • Canon REALiS LCOS 4K500ST | User Manual - Page 88
    Auto] mode, the signal level is selected automatically. (Some equipment may not support this.) • If HDMI output can be set to [Normal] or [Expanded For more detailed information, refer to the user's manual for the AV equipment connected to the projector. Super white > [Input settings] > [Super
  • Canon REALiS LCOS 4K500ST | User Manual - Page 89
    Selects the optimal color format for input signals. Forces the projector to handle the input signal as an RGB signal. Forces the projector to handle the input signal as a color difference signal. lines are noticeable in media that has a lot of fast-moving action. Advanced Guide Menu Settings 89
  • Canon REALiS LCOS 4K500ST | User Manual - Page 90
    Menu Settings Image adjustment This section describes image quality settings such as brightness, contrast, and sharpness. (When the input signal is HDMI-1) Menu Function Details Image mode * Select overall image quality to suit the projected image. P91 Create profile Save desired image
  • Canon REALiS LCOS 4K500ST | User Manual - Page 91
    gamma values used for medical images * Conforms to DICOM Standard Part 14. However, the projector cannot be used in diagnosis or similar applications. User 1 - 3 Up to 3 user ] • If flickering occurs in Presentation mode, try switching to sRGB or Standard mode. Advanced Guide Menu Settings 91
  • Canon REALiS LCOS 4K500ST | User Manual - Page 92
    Menu Settings Create profile > [Image adjustment] > [Create profile] Save desired image quality settings in up to 3 user profiles. • The saved settings consist of the brightness, contrast, sharpness, gamma, color adjustment, advanced adjustment, and lamp mode. • Although only 3 user profiles are
  • Canon REALiS LCOS 4K500ST | User Manual - Page 93
    5 (Blue Base): Adjust color to suit the color of X-ray film. Advanced adjustment > [Image adjustment] > [Advanced adjustment] Fine-tune noise reduction and color tone. Advanced Guide Menu Settings 93
  • Canon REALiS LCOS 4K500ST | User Manual - Page 94
    Menu Settings Ambient light Minimize the effect of ambient light on the screen. Submenu Function Off Projects an image with no correction. Adjust Type Tungsten Fluorescent For ambient light from conventional light bulbs or fluorescent light of this color. For ambient light from a "day
  • Canon REALiS LCOS 4K500ST | User Manual - Page 95
    Advanced Guide Menu Settings Menu Settings Dynamic gamma You can adjust the gradation representation of light and dark portions of an image automatically. Option Function Off Disable
  • Canon REALiS LCOS 4K500ST | User Manual - Page 96
    Menu Settings Fine-Tune Gamma Adjust white, red, green, and blue gamma curves. Red, green, and blue can be adjusted separately. Adjustments to white are also applied to the three other colors. Note that adjusting any color will overwrite previous adjustments. • [Fine-Tune Gamma] is available in
  • Canon REALiS LCOS 4K500ST | User Manual - Page 97
    to suit the screen or the type of images, or how the projector is installed. (When the input signal is HDMI-1) Menu Positional lock the screen color. Reduce the difference in brightness among models when multiple projectors are used together, by adjusting the lens aperture. Project a test pattern
  • Canon REALiS LCOS 4K500ST | User Manual - Page 98
    the screen. The projected image is inverted in both vertical and horizontal directions. • To hang the projector from the ceiling, use the optional bracket. Contact the Canon Customer Support Center for more detailed information. • Image flipping will reset any adjustment for keystone distortion. In
  • Canon REALiS LCOS 4K500ST | User Manual - Page 99
    Professional settings > [Install settings] > [Professional settings] Specify advanced installation settings. Menu Settings Advanced Guide Menu Settings Panel drive mode Select the LCD panel vertical resolution to use. Option Function 4096x2160 Use a resolution of 4096 x 2160 lines.
  • Canon REALiS LCOS 4K500ST | User Manual - Page 100
    , set [DVI dual link auto setting] to [Off]. • In some cases when DVI terminals are used, the cable may not be a good match for the projector, which may cause video noise or prevent the signal from being detected. If this occurs, adjust values in each setting from [DVI-1 equalizer setting] to
  • Canon REALiS LCOS 4K500ST | User Manual - Page 101
    Guide Menu of the screen is possible by color and area. For detailed instructions, refer to "Advanced Registration to Adjust Projected Images" (P153). color misalignment. Advanced registration Submenu 5-point adjustment Manual adjustment Reset Function Off Disable adjustment. Adjust Enter
  • Canon REALiS LCOS 4K500ST | User Manual - Page 102
    be used to activate and deactivate this focus adjustment. For detailed instructions, refer to "Adjusting Peripheral Focus" (P157). Option Function Off access the adjustment On window, press the LENS button on the projector repeatedly or press the FOCUS button on the remote control. Reset
  • Canon REALiS LCOS 4K500ST | User Manual - Page 103
    area, can be adjusted for a more seamless appearance. For detailed instructions, see "Projecting from Multiple Projectors at Once (Edge Blending)" (P149). [Off] Disable blending. adjustment, by fine-tuning gamma (4) Corner adjustment, using keystone correction Advanced Guide Menu Settings 103
  • Canon REALiS LCOS 4K500ST | User Manual - Page 104
    Menu Settings Submenu Side Function Submenu Left Right Top Bottom Width Function Select the direction of the blending area to adjust. Specify the width between the start and end markers. Moves the position of the start marker. Start position • Large blending areas may cover input signal dialog
  • Canon REALiS LCOS 4K500ST | User Manual - Page 105
    Advanced Guide Menu Settings Submenu Black level adjustment Marker Reset Menu Settings Function Because black is lighter in the blending area than in other areas, you can
  • Canon REALiS LCOS 4K500ST | User Manual - Page 106
    Menu Settings Lens - Position > [Install settings] > [Lens - Position] The projector can store information about the lens position. Up to three sets of lens information (including, focus, zoom, and lens shift settings) can be saved, and
  • Canon REALiS LCOS 4K500ST | User Manual - Page 107
    ] > [Iris] The difference in brightness among models can be reduced when multiple projectors are used together, by adjusting the lens aperture. Submenu Open Close 1-3 Function Disables a little while, but you can view it again by pressing the [ ] / [ ] buttons. Advanced Guide Menu Settings 107
  • Canon REALiS LCOS 4K500ST | User Manual - Page 108
    . Select the terminal for audio input. Display serial communication setting values. You can specify to turn off the lamp or projector automatically after a certain period if the projector and remote control are not used and there is no input signal. Specify how long before the lamp is turned off
  • Canon REALiS LCOS 4K500ST | User Manual - Page 109
    and specify logo display settings. Menu Settings Advanced Guide Menu Settings Logo capture Registers the current image Projector on Select a logo to project after startup until input signals can be projected. Option Function Skip A black screen is projected. Canon logo Displays the Canon
  • Canon REALiS LCOS 4K500ST | User Manual - Page 110
    Menu Settings On screen > [Sysetm settings] > [On screen] Specify display details for on-screen menus, help, and warning or precaution icons. Menu position Reposition menu display. Choose from upper left, upper right, center, lower left, or lower right. Only [Center] is available when edge
  • Canon REALiS LCOS 4K500ST | User Manual - Page 111
    Settings Menu Settings Guide Shows the guide screen. Option Off Hides the guide screen. On Shows the guide screen. Function The guide screen is shown displayed. • When it is almost time to replace the lamp, the projector's [LAMP] indicator will flash. For details, see "LED Indicator
  • Canon REALiS LCOS 4K500ST | User Manual - Page 112
    down instead of pressing them repeatedly. Option Function Off Key repeat is not enabled. On Key repeat is enabled. Key lock Lock the projector to prevent direct or remote control operation. Option Function Off Disables the key lock. Main unit Operation is not possible using the main
  • Canon REALiS LCOS 4K500ST | User Manual - Page 113
    Advanced Guide Menu Settings Menu Settings To Unlock Key Lock Function Turn off the projector and unplug the beep will sound, and the controls will be unlocked. When you access this setting from the projector's side controls, [Main unit] is not available. Similarly, when you access the setting
  • Canon REALiS LCOS 4K500ST | User Manual - Page 114
    [Serial communication] You can check setting values for the service port (CONTROL) used for serial communication. Option Stop bit Standby Function Disable power management mode. Only turns the lamp off. Turns the projector off and puts it in standby. • After the lamp is turned off, projection
  • Canon REALiS LCOS 4K500ST | User Manual - Page 115
    to turn the projector on. You can turn on the projector by connecting the turning off the projector, wait at least 5 minutes before turning it life if you turn on the projector immediately after turning it off. and flickering may occur. • If setting the projector to [Strong] or [Weak] produces distracting
  • Canon REALiS LCOS 4K500ST | User Manual - Page 116
    Menu Settings Language > [System settings] > [Language] Select the menu display language. Language English Russian German Dutch French Finnish Italian Norwegian Spanish Turkish Portuguese Polish Swedish Hungarian Czech Danish Arabic Chinese (Simplified) Chinese (Traditional) Korean
  • Canon REALiS LCOS 4K500ST | User Manual - Page 117
    , reset counters for lamp or air filter replacement, and access other settings and information. Advanced Guide Menu Settings Password settings Disables the projector unless the correct password is entered. Option Function Off The projector can be used even if no password is entered. On The
  • Canon REALiS LCOS 4K500ST | User Manual - Page 118
    panel characteristics Adjust projection to compensate for how long the projector has been used, the projection environment, and other ambient temperature. Compensates for changes in gradation caused by a change in LCOS panel temperature. Submenu Off Adjust Function Do not adjust the panels to
  • Canon REALiS LCOS 4K500ST | User Manual - Page 119
    before updating the firmware. Update the projector firmware as follows. 1. Download updated firmware from the Canon website and store it at the root directory on a USB flash drive. 2. Insert the USB flash drive in the USB port. 3. Follow the instructions shown to complete the update process
  • Canon REALiS LCOS 4K500ST | User Manual - Page 120
    Menu Settings Factory defaults You can reset the menu item settings and restore the system settings to the factory defaults. Option Function OK Settings are reset to default. Cancel Settings are not reset to default. Main factory defaults Input settings Submenu Aspect Input level Super
  • Canon REALiS LCOS 4K500ST | User Manual - Page 121
    screen settings Logo capture Cancel Logo position Center No signal screen Blue Screen when blank Black Projector on Canon logo On screen Menu position Center Menu display time Normal Guide On Show input status On Lamp warning display On Air filter warning display On Overheat
  • Canon REALiS LCOS 4K500ST | User Manual - Page 122
    not overlap with other computers that are on the same LAN. To set a projector IP address, follow the instructions in "Completing Computer Settings for a Network Connection" (P130) and use the web screen, or use projector TCP/ IP settings. (P126) • When you connect the computer to the network for
  • Canon REALiS LCOS 4K500ST | User Manual - Page 123
    Menu Settings Completing Projector Settings Settings described in this section apply to the network connections, setting a network password, and other aspects of RoomView Enable or disable Crestron RoomView. Details P124 P124 P124 P125 P125 P126 P128 P129 P129 Advanced Guide Menu Settings 123
  • Canon REALiS LCOS 4K500ST | User Manual - Page 124
    setting > [Network settings] > [Network password setting] You can set whether or not a password is required in order to change the projector network settings. Option Off On Function A network password is not used. A network password is used. Register network password > [Network settings
  • Canon REALiS LCOS 4K500ST | User Manual - Page 125
    network, and PJLink. All network functions are available even in standby mode. However, the projector may be less responsive than usual when some functions are initially used. • [Low-power] On Function Disable the network function. Enable the network function. Advanced Guide Menu Settings 125
  • Canon REALiS LCOS 4K500ST | User Manual - Page 126
    Gateway address MAC address DHCP Function IP address of the projector. Gateway address of the projector. MAC address of the projector. Submenu Off On Function Disables the DHCP function. TCP/IP settings must be configured manually. Enables the DHCP function. Searches the DHCP server. TCP/IP
  • Canon REALiS LCOS 4K500ST | User Manual - Page 127
    The following network settings are initialized. Settings configured from the projector menu • Network settings lock (P124) • Network password ] (P137) • [Mail] (P138) • [Mail auth] (P139) • [SNMP] (P140) • [Projector info.] (P141) • [PJLink] (P142) Menu Settings Advanced Guide Menu Settings 127
  • Canon REALiS LCOS 4K500ST | User Manual - Page 128
    conforms to Class 1 as defined in PJLink standards established by the Japan Business Machine and Information System Industries Association (JBMIA). This projector supports all commands that are defined by PJLink Class 1, and has been verified as conforming to the PJLink standard Class 1 definition
  • Canon REALiS LCOS 4K500ST | User Manual - Page 129
    ] > [Crestron RoomView] Crestron RoomView enables centralized management of multiple projectors over a network. Networked projectors can be remotely controlled to troubleshoot issues, check the useful life of lamps, or turn the projectors on or off. Specify whether to use Crestron RoomView. Option
  • Canon REALiS LCOS 4K500ST | User Manual - Page 130
    Computer Settings for a Network Connection Specifying an IP Address Instructions for setting a computer's IP address are as follows ] and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. 8
  • Canon REALiS LCOS 4K500ST | User Manual - Page 131
    Advanced Guide Menu Settings Menu Settings ■ Windows 7 1 From the PC [Start] menu, select the following IP address] and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. 7 When the settings are
  • Canon REALiS LCOS 4K500ST | User Manual - Page 132
    mask, router, DNS server, etc.). 4 Create a new network environment and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. 5 Click [Apply] to close the network preference window. ■ Resetting the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 133
    projector is installed MAC address The MAC address of the projector IP address Power status The IP address of the projector The power status of the projector ask the network administrator for the projector IP address. It is possible to check the IP address from the projector menu. (P126) 3 Click
  • Canon REALiS LCOS 4K500ST | User Manual - Page 134
    default user name is "root" and the password is "system". The settings screen is displayed. Complete the network settings on this screen. To control the projector from the computer, click [Projector control]. (P146) ■ Network Setting 1 Select a function to set up from the settings screen menu. 134
  • Canon REALiS LCOS 4K500ST | User Manual - Page 135
    Advanced Guide Menu Settings Menu Settings 2 Enter setting details in the fields shown (1), and then click [OK] (2). (1) (2) 3 A confirmation window appears. Check the contents and if they are correct, click [Apply]. The settings are applied to the projector. Selecting [Network] or [Password] in
  • Canon REALiS LCOS 4K500ST | User Manual - Page 136
    Menu Settings Setting a Password [Password] From [Password] in the settings screen, you can set a user name and password for web screen login. For the setting procedure, refer to "Network Setting" (P134). Item User name New password Confirm new password Explanation When logging into the web screen
  • Canon REALiS LCOS 4K500ST | User Manual - Page 137
    set basic network information. For the setting procedure, refer to "Network Setting" (P134). Advanced Guide Menu Settings Item MAC address DHCP IP address Subnet mask Default gateway Explanation Shows the projector's MAC address. Select whether to turn the DHCP function on or off. If the function
  • Canon REALiS LCOS 4K500ST | User Manual - Page 138
    address for error mails in 1-byte alphanumeric characters and symbols (1 - 63 characters). Enter the sender address for error mails [email protected] in 1-byte alphanumeric characters and symbols (1 - 63 characters). Enter the SMTP server IP address in 1- 0.0.0.0 byte numbers. Enter
  • Canon REALiS LCOS 4K500ST | User Manual - Page 139
    the settings for authentication of mail that is sent when an error occurs. For the setting procedure, refer to "Network Setting" (P134). Advanced Guide Menu Settings Item Mail authentication User name Password Confirm password POP3 server IP address POP3 server port number POP before SMTP response
  • Canon REALiS LCOS 4K500ST | User Manual - Page 140
    screen (P138) is displayed. The sender address which was set from [Mail] in the settings screen (P138) is displayed. The predetermined mail title "Canon Projector test" is displayed. SNMP Settings [SNMP] From [SNMP] in the settings screen, you can configure the settings related to control of
  • Canon REALiS LCOS 4K500ST | User Manual - Page 141
    are installed on the network. For the setting procedure, refer to "Network Setting" (P134). Advanced Guide Menu Settings Item Projector name Comment Explanation Enter the projector name in 1-byte alphanumeric characters and symbols (1 - 63 characters). Enter any relevant notes, such as where
  • Canon REALiS LCOS 4K500ST | User Manual - Page 142
    Menu Settings Setting PJLink [PJLink] From [PJLink] in the settings screen, you can set the PJLink functions which are the standard for projector management on a network. For the setting procedure, refer to "Network Setting" (P134). For information about PJLink, refer to "What is PJLink?" (P128).
  • Canon REALiS LCOS 4K500ST | User Manual - Page 143
    SMTP server. System failed to connect POP3 server. System doesn't support this auth type. System failed to authenticate. The system failed to send a test mail. An authentication type was set which is not supported by the server. Authentication failed attempting to send a test mail. Sending of
  • Canon REALiS LCOS 4K500ST | User Manual - Page 144
    Menu Settings Resetting Network Settings to the Default Settings 1 Perform steps 1 - 3 on "Displaying the Network Configuration Screen" (P132) to display the settings screen. 2 Click [Initialize]. 3 A confirmation window appears. Click [OK]. 144
  • Canon REALiS LCOS 4K500ST | User Manual - Page 145
    are sent when an error occurs in the projector. Error list Errors related to temperature Errors the problem is inside the projector, check whether the projector is installed and operated normally, turn off the projector to same warning occurs again, the projector may be defective. Contact your
  • Canon REALiS LCOS 4K500ST | User Manual - Page 146
    address is "192.168.254.254". If DHCP settings are used, ask the network administrator for the projector IP address. It is possible to check the IP address from the projector menu. 3 Click [Projector control] on the web screen. The password input window appears. 4 Enter the user name and password on
  • Canon REALiS LCOS 4K500ST | User Manual - Page 147
    Advanced Guide Menu Settings Menu Settings 5 When the operations are finished, click [Back to top] to return the initial web screen. 147
  • Canon REALiS LCOS 4K500ST | User Manual - Page 148
    type, resolution, frequency, and color format of the signal is displayed. Firmware Current firmware version Serial no. Serial number unique to this projector IP address IP address used when connected to a network. E-mail sender address* Sender e-mail address used for sending error mails (P138
  • Canon REALiS LCOS 4K500ST | User Manual - Page 149
    Guide Advanced Projection Advanced Projection Projecting from Multiple Projectors at Once (Edge Blending) Overlapping edges of images from multiple projectors used together can be blended to make the overall image more seamless. ■ Basic Instructions Follow these steps when using two projectors
  • Canon REALiS LCOS 4K500ST | User Manual - Page 150
    and [Blue] values individually. 3 Repeat this adjustment on all projectors. ■ Black Level Adjustment In overlapping projection, dark colors are are identified in the context of end markers: A, B, and C. In the following instructions, only area D is adjusted, and the widths of A, B, and C are left
  • Canon REALiS LCOS 4K500ST | User Manual - Page 151
    blending area and area D match. Advanced Guide Advanced Projection Adjust [D-area base] to needed. 4 Repeat this adjustment on all projectors. ■ Smoother Overlapping Areas The black level to suit these blending areas. In this example, instructions are given for adjusting area B. 1 In the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 152
    Advanced Projection 3 Select [B-width], and then specify the width of area B. Adjust the width of area B so that it roughly matches the area where the black level of area B stands out. This will make the width of area D narrower. 4 Select [Adjustment type] > [Black level]. Adjust [B-area base] as
  • Canon REALiS LCOS 4K500ST | User Manual - Page 153
    Guide Advanced Projection Advanced Projection Advanced Registration to Adjust Projected Images Any values you set in 5-point adjustment are retained if you subsequently perform manual adjustment. For more precise correction after 5-point adjustment, perform manual ]. The projector enters 5-point
  • Canon REALiS LCOS 4K500ST | User Manual - Page 154
    Advanced Projection 2 Use the buttons to select the point for correction, and then press the OK button. The projector enters color selection mode. 3 Select [Red] or [Blue] as the color, and then press the OK button. • Select [Chart] to toggle between display of the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 155
    Guide Advanced Projection Advanced Projection ■ Manual Registration Use manual adjustment to correct registration only in certain areas. Any manual ] > [Advanced registration] > [Adjust] > [Manual adjustment]. The projector enters manual adjustment mode, and a point selection window is displayed
  • Canon REALiS LCOS 4K500ST | User Manual - Page 156
    , and then press the OK button. • Select [Chart] to toggle between display of the point selection window and source signal. • Accessing the manual adjustment window during test pattern projection will show the test pattern instead of your supplied signal. 4 Use the buttons to align the adjustment
  • Canon REALiS LCOS 4K500ST | User Manual - Page 157
    press the FOCUS button on the remote control or the LENS button on the projector. 1 Press the FOCUS button on the remote control twice to display the marginal control Press twice. Pressing the LENS button on the projector repeatedly switches between windows for lens-related parameters. Press the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 158
    Advanced Projection 2 Press the pointer buttons to adjust the focus at image edges. Remote control Projector Press the [ ] / [ ] buttons to move the peripheral focus farther away. Press the [ ] / [ ] buttons to move the peripheral focus nearer. 3 Once image edges are in focus,
  • Canon REALiS LCOS 4K500ST | User Manual - Page 159
    Other Information Other Information Advanced Guide Basic Guide Safety Instructions Before Use Installation Procedure Connection Procedure Projection Procedure Convenient Features Using Menus Menu Settings Advanced Projection Maintenance Product Specifications Troubleshooting 159
  • Canon REALiS LCOS 4K500ST | User Manual - Page 160
    the finish of the projector. • When using a chemical dust cloth, make sure to read the instructions thoroughly. • When cleaning the projector's lens, use a electric shock. Once a year, request internal cleaning from the Canon Customer Support Center. (Note that a fee is charged.) Cleaning before
  • Canon REALiS LCOS 4K500ST | User Manual - Page 161
    no longer displayed. • This screen is not displayed when [Air filter warning display] is set to [Off]. (P111) Reset the air filter counter manually. (P119) Replacing the Air Filter Follow the procedure below when replacing the air filter. 1 Turn off the projector power and remove the power plug. 161
  • Canon REALiS LCOS 4K500ST | User Manual - Page 162
    Maintenance 2 Pull out the filter cover tab on bottom while lifting up. 3 Open the filter cover and remove it. 4 Remove the air filter. 5 Holding the new air filter by the tab, insert the air filter in the projector. 162
  • Canon REALiS LCOS 4K500ST | User Manual - Page 163
    replace the lamp. • Contact the Canon Customer Support Center for further information. • Replacement air filter Canon website. Replacing the Lamp When the usage time of the lamp exceeds a certain amount of time, the following message (two types) is displayed for 10 seconds every time the projector
  • Canon REALiS LCOS 4K500ST | User Manual - Page 164
    on, the lamp may be broken. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. Additionally, with ceiling-mounted projectors, the lamp may fall out when you open the lamp cover or while you are attempting to replace it. During
  • Canon REALiS LCOS 4K500ST | User Manual - Page 165
    . Doing so may cause deterioration to the projector's performance. • Handle lamps with care. Impact or abrasion may cause lamps to rupture while they are in use. If a lamp ruptures, contact the Canon Customer Support Center and follow the instructions in "Precautions when replacing lamps that stop
  • Canon REALiS LCOS 4K500ST | User Manual - Page 166
    Maintenance 3 Hook your finger around the lamp cover handle, and open the cover in the direction of the arrow. The lamp cover screw is attached to the lamp cover to prevent it from falling off. 4 Loosen the 3 screws on the inside of the lamp unit, and then slowly pull out the lamp unit in the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 167
    lamp counter. • We recommend cleaning or replacing the air filter (part no.: RS-FL03) when you replace the lamp. • To order air filters, contact the Canon Customer Support Center. 167
  • Canon REALiS LCOS 4K500ST | User Manual - Page 168
    Product Specifications Displayed Test Patterns To access the test pattern menu, from the [Install settings] menu, select [Test pattern] (P107) > [On], or press the TEST PATTERN button on the remote control. While the test pattern is displayed, you can use the [ ] / [ ] buttons to switch patterns.
  • Canon REALiS LCOS 4K500ST | User Manual - Page 169
    Specifications Supported Signal Types This projector supports the following signal types. If your computer or AV equipment is compatible with any of these signals, the projector will determine , so the computer output format must be configured manually. Other Information Product Specifications 169
  • Canon REALiS LCOS 4K500ST | User Manual - Page 170
    EDID for fields that are blank, so the computer output format must be configured manually. Colors may appear distorted when images are viewed from the side on some screens, but this does not indicate a problem with the projector. For best results, use a matte screen with a wide viewing angle. 170
  • Canon REALiS LCOS 4K500ST | User Manual - Page 171
    in the EDID. No information is provided in the EDID for fields that are blank, so the computer output format must be configured manually. DVI 1x2 1 3 Combined multi input resolution Resolution at each input terminal Horizontal frequency [kHz] Vertical frequency [Hz] Dot clock [MHz] DVI multi
  • Canon REALiS LCOS 4K500ST | User Manual - Page 172
    are identified in the EDID. No information is provided in the EDID for fields that are blank, so the computer output format must be configured manually. 172
  • Canon REALiS LCOS 4K500ST | User Manual - Page 173
    fields that are blank, so the computer output format must be configured manually. Colors may appear distorted when images are viewed from the side on some screens, but this does not indicate a problem with the projector. For best results, use a matte screen with a wide viewing angle. Active video
  • Canon REALiS LCOS 4K500ST | User Manual - Page 174
    Product Specifications Specifications ■ Projector Model name 4K500ST Display system RGB liquid crystal system: reflective (LCOS) : 3 panels Optical system Color separation by dichroic mirror / polarizing beam splitter and color composition by prism Projection lens Display device Type / No.
  • Canon REALiS LCOS 4K500ST | User Manual - Page 175
    terminal HDMI terminal LAN terminal USB port CONTROL terminal REMOTE terminal AUDIO IN terminal AUDIO OUT terminal 4K500ST 640 x 480, 720 x 480, 720 x 576, 800 x 600, 1280 x 720, lens cap, Important Information, User's Manual (CD-ROM) and Warranty Card Other Information Product Specifications 175
  • Canon REALiS LCOS 4K500ST | User Manual - Page 176
    supported * 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels may stay lit or unlit due to the characteristics of the LCD panel. * Using the projector 6.9 (D) in 100 g / 3.5 oz ■ External View 4K500ST 175 mm (6.9") 75 mm (3.0") 155 mm (6.1") 111.6 mm
  • Canon REALiS LCOS 4K500ST | User Manual - Page 177
    ■ Service Port (CONTROL) Product Specifications Pin assignment Pin No. Signal 1 OPEN 2 RxD 3 TxD 4 OPEN 5 GND 6 OPEN 7 Internal pull-up 8 OPEN 9 OPEN Communication format Communication mode : RS-
  • Canon REALiS LCOS 4K500ST | User Manual - Page 178
    Product Specifications Main user commands Commands Power on Power supply Power off Power status acquisition HDMI-1 HDMI-2 HDMI 1x2 DVI-1 DVI-2 Input source DVI-3 DVI-4 DVI 1x2 DVI 2x2 DVI 1x4 Input source acquisition Standard Presentation Photo/sRGB DICOM SIM Image Mode Dynamic Video User 1
  • Canon REALiS LCOS 4K500ST | User Manual - Page 179
    Product Specifications Commands ASCII representation Brightness acquisition GET=BRI Sharpness Sharpness value setting SHARP= Sharpness acquisition GET=SHARP Contrast Contrast value setting CONT= Contrast acquisition GET=CONT Aspect Auto True size
  • Canon REALiS LCOS 4K500ST | User Manual - Page 180
    Troubleshooting LED Indicator Details When there is a problem with the projector, the LED indicator on the side of the projector illuminates or flashes continuously after the projector may be a malfunction in the projector. Contact the Canon Customer Support Center. WARNING and Faulty lamp LAMP
  • Canon REALiS LCOS 4K500ST | User Manual - Page 181
    . Remove any obstacle that is blocking the air intake or exhaust vent and contact the Canon Customer Support Center. Check whether the air filter is installed correctly. (P161) Check that Key lock (P112) is not enabled for the projector or the remote control. Other Information Troubleshooting 181
  • Canon REALiS LCOS 4K500ST | User Manual - Page 182
    Troubleshooting ■ You Cannot Project an Image from the Projector Cause A cable is not connected correctly. 20 seconds have not elapsed since the projector was turned on. No image is sent from the AV . For more detailed information, refer to the manual that came with your computer. Check whether the
  • Canon REALiS LCOS 4K500ST | User Manual - Page 183
    Troubleshooting ■ There is no Sound Cause The audio cable is not connected correctly is high, condensation may form on the lens. The condensation will evaporate after a period of time and the projector will be able to project a normal image. Clean the lens. (P160) Activate motion blur reduction. (
  • Canon REALiS LCOS 4K500ST | User Manual - Page 184
    Troubleshooting ■ You Cannot Project an Image Appropriately Cause The projected image is the projector. (P25, P60) Check whether the air filter is clogged with dust. If the air filter is clogged, clean or replace the air filter. (P160, P161) If the lamp has ruptured, follow the instructions in
  • Canon REALiS LCOS 4K500ST | User Manual - Page 185
    Troubleshooting ■ You Cannot Operate the Remote Control Cause Batteries are not installed properly or they have run out. You are operating the remote control from the outside of the remote control operating range. There is an obstacle between the projector and the remote control. You are operating
  • Canon REALiS LCOS 4K500ST | User Manual - Page 186
    IMAGE 77 Image adjustment 84, 90 Image mode (Image quality 76 Information 84, 148 INPUT 63 Input signal select 63 Input terminal 29 Connecting to AV equipment 54 K Key lock 112 KEYSTONE 73 Keystone 73 L Lamp mode 96 Lamp replacement 163, 165 LAN port 29 Language 116 LED indicator 27
  • Canon REALiS LCOS 4K500ST | User Manual - Page 187
    30 Optical zoom 68 P Password 117, 118 PJLink 128, 142 POWER 60, 79 Power-Saving Settings 81 Projecting from Multiple Projectors at Once (Edge Blending 149 Projector on 109 T Test pattern 168 True size (Aspect 72 Turning on external monitor output (preparing the notebook computer 62 U USB
  • Canon REALiS LCOS 4K500ST | User Manual - Page 188
    air filter Part No.: RS-LP10F • Remote control Part No.: RS-RC05 • Remote control Part No.: RS-RC04 * Use the above materials to hang the projector from the ceiling. 188
  • Canon REALiS LCOS 4K500ST | User Manual - Page 189
    INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A. INC. One Canon Park, Melville, New York 11747, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANON EUROPE LTD. 3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET United
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Connection Procedure
Projection Procedure
Convenient Features
Advanced Guide
Using Menus
Menu Settings
Advanced Projection
Other Information
Maintenance
Product Specifications
Troubleshooting
ENG
MULTIMEDIA PROJECTOR
User’s Manual