Canon REALiS WUX4000 User manual

Canon REALiS WUX4000 Manual

Get Canon REALiS WUX4000 PDF manuals and user guides View all Canon REALiS WUX4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Canon REALiS WUX4000 manual content summary:

  • Canon REALiS WUX4000 | User manual - Page 1
    MULTIMEDIA PROJECTOR User's Manual/ Installation Manual Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network
  • Canon REALiS WUX4000 | User manual - Page 2
    How to Use This Manual Thank you for purchasing a Canon projector. The WUX4000 Multimedia Projector (hereinafter referred to as "the projector") is a highperformance projector that is capable of projecting a high-resolution computer screen and high-quality digital image on a large screen. User's
  • Canon REALiS WUX4000 | User manual - Page 3
    Saving Mode (P96) Turning on the Projector by Connecting the Power Cord (P96) Disabling the Beep During Operation (P97) Disabling Buttons (P97) Hiding Guide Messages (P99) Setting a Password (P101) Producing a Presentation Temporarily Blacking Out an Image (P66) Freezing the Picture (P66) Adjusting
  • Canon REALiS WUX4000 | User manual - Page 4
    Manual 2 Quick Reference Guide 3 Safety Instructions...10 Safety Precautions ...11 CAUTION ON HANGING FROM THE CEILING 11 ■ READ AND KEEP THIS OWNER'S MANUAL an Image 35 Steps for Connecting the Projector and Projecting an Image 36 Connecting the Projector 37 Connecting the Projector to
  • Canon REALiS WUX4000 | User manual - Page 5
    ...59 Adjusting Keystone Distortion 59 ■ Resetting the Keystone Adjustment 61 Selecting an Image Mode 62 ■ Image Modes...62 ■ How to Select an Image Mode 63 Turning Off the Projector 64 Useful Functions Available During a Presentation 65 Useful Functions Available During a Presentation
  • Canon REALiS WUX4000 | User manual - Page 6
    Selecting an Image Projection Selecting an Image Quality 86 Image adjustment...86 Saving the Desired Image Quality 87 89 Adjusting Color ...90 Correcting the Image According to the Ambient Light 91 Noise ...94 Reducing the Lamp Brightness 95 Resetting the Image Settings 95 Setting Various
  • Canon REALiS WUX4000 | User manual - Page 7
    Display Language 99 Showing/Hiding the Guide Screen 99 Showing/Hiding the Input Lamp Counter 105 ■ About the Display of the Lamp Counter 106 Resetting to the Default Setting 107 Checking Projector Projector 122 ■ Positioning the Projector in Front of the Screen 122 ■ Relationship Between Image
  • Canon REALiS WUX4000 | User manual - Page 8
    150 Controlling the Projector from a Computer 151 Error Mail ...153 Maintenance 155 Cleaning the Projector 156 Cleaning and Replacing the Air Filter 157 Replacing the Air Filter ...157 Cleaning the Air Filter...158 Replacing the Lamp 159 Replacement Lamp ...160 Replacing the Lamp ...160 8
  • Canon REALiS WUX4000 | User manual - Page 9
    of Contents Appendix 163 Appendix ...165 Troubleshooting ...166 LED Indicator Meanings ...166 Symptoms and Solutions ...167 ■ You Cannot Turn on the Projector 167 ■ You Cannot Project an Image from the Projector 167 ■ You Cannot Hear Sound 168 ■ The Projected Image Is Blurred 169 ■ You Cannot
  • Canon REALiS WUX4000 | User manual - Page 10
    , check operations and cable connections, and try the solutions in the "Troubleshooting" section in the back of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE
  • Canon REALiS WUX4000 | User manual - Page 11
    not cover the ventilation slots on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous. • If the projector is unused for an extended time, unplug the projector from the power outlet. • Do not project the same image for a long time. An afterimage may
  • Canon REALiS WUX4000 | User manual - Page 12
    ■READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. All the safety and operating instructions should be read before beginning to operate the product. Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Do not
  • Canon REALiS WUX4000 | User manual - Page 13
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally after following the operating instructions
  • Canon REALiS WUX4000 | User manual - Page 14
    Instructions AC Power Cord Requirement The AC Power Cord supplied with this projector . NOTE FOR CUSTOMERS IN THE US LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST authorized one-for-one basis when you buy a new similar product or to an service or visit www.canon-europe.com/environment. (EEA
  • Canon REALiS WUX4000 | User manual - Page 15
    Safety Instructions Safety Instructions Federal Communication Commission Notice Multimedia Projector, Model: WUX4000 This device complies in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Plaza,
  • Canon REALiS WUX4000 | User manual - Page 16
    power outlet and contact a Canon dealer. Failure to do so could cause a fire or result in an electric shock. • If smoke is emitted • If an unusual smell or noise is emitted • If a loud noise is heard and the lamp turns off • If water or other liquid has entered the projector • If metal or
  • Canon REALiS WUX4000 | User manual - Page 17
    Safety Instructions Safety Instructions Warning Pay attention to the following points regarding to a body of water. • Do not place containers containing a liquid on top of the projector. • Do not place the projector in any location where it will be exposed to oily smoke or steam, such as a kitchen
  • Canon REALiS WUX4000 | User manual - Page 18
    maintenance or repair is required, contact a Canon dealer. • Do not disassemble or modify the projector (including consumable parts) or the remote • When giving a presentation in front of the projector while it is projecting an image, conduct your presentation from a position where your shadow
  • Canon REALiS WUX4000 | User manual - Page 19
    do so could result in an electric shock or personal injury. • Be sure to remove the power plug from the power outlet before replacing the lamp. • When the lamp is damaged, shards of glass may be scattered inside the projector. Contact a Canon dealer for cleaning and inspection of the
  • Canon REALiS WUX4000 | User manual - Page 20
    to do so could result in a burn or personal injury due to heat from the lamp or projector. • When an instruction to replace the lamp has been displayed (LAMP Indicator Displays (P31)), the possibility of the lamp breaking will increase. Replace the lamp with a new one as soon as possible. • If the
  • Canon REALiS WUX4000 | User manual - Page 21
    Safety Instructions Safety Instructions For Safe Use Precautions for Carrying and Transporting Projector • This projector is a precision instrument. Do not knock it over or subject it to impacts. Doing so may cause a malfunction. • When carrying or holding up the projector after attaching the lens
  • Canon REALiS WUX4000 | User manual - Page 22
    components such as the lens and the mirror and may result in deterioration of image quality. • Do not touch the lens with bare hands. Doing so may result in deterioration of image quality. • If the projector is suddenly moved from a location where the temperature is low to a location where the
  • Canon REALiS WUX4000 | User manual - Page 23
    Before Use 23 Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Appendix Index
  • Canon REALiS WUX4000 | User manual - Page 24
    Accessories Check that the following accessories have been supplied with the projector.  Remote control (part No.: RS-RC04)  Batteries mini D-sub 15-pin) For the U.S.A. and Canada  User's Manual/ Installation Manual (CD-ROM)  Warranty Card  Important Information ■Installing Remote Control
  • Canon REALiS WUX4000 | User manual - Page 25
    control at the infrared remote receiver on the front or rear of the projector whenever pressing any button. (26.3') (26.3') • Use the remote control strong light of lighting equipment. • When you use 2 or more projectors at the same time, you can change the channel settings to prevent the 2 remote
  • Canon REALiS WUX4000 | User manual - Page 26
    Part Names Main Unit of Projector ■Front Side Power cord connector (P43) Side control (P30) Lens unit Air intake vent Terminals and connectors a malfunction. ■Rear Side Exhaust vent Do not block the air exhaust. Doing so may cause a malfunction. Lamp cover Infrared remote receiver (P25) 26
  • Canon REALiS WUX4000 | User manual - Page 27
    on the installation environment, an extension pipe (part No.: RS-CL08 or RS-CL09) may also be required. Contact a Canon dealer where you purchased the projector for more detailed information. • Make sure to use the optional ceiling attachment. • You should never install the ceiling attachment by
  • Canon REALiS WUX4000 | User manual - Page 28
    remote control allows you to operate all functions of the projector. POWER button (P43, P64) Turns the projector on or off. FOCUS button (P57) Adjusts focusing Moves the image up, down, left, or right when [16:9 D. image shift] or [4:3 D. image shift] is selected. (P52, P53) • To move the image, use
  • Canon REALiS WUX4000 | User manual - Page 29
    (P66) Mutes the sound. Toggles between display/non-display of image. LAMP button (P95) GAMMA button (P89) Adjusts the gamma of the image. Toggles the lamp mode between Standard and Silent. [ ] button: Corrects dark parts of the image so that they are easier to see. [ ] button: Corrects bright
  • Canon REALiS WUX4000 | User manual - Page 30
    . • STAND BY (red) : Lights up or flashes during standby or when the projector is shut down. • WARNING (red) : Lights up or flashes when an error occurs. • LAMP (orange) : Flashes when the time for replacing the lamp is near. Also lights up together with the [WARNING] indicator (constantly lit
  • Canon REALiS WUX4000 | User manual - Page 31
    Indicator Displays The illumination status of the LED indicators indicates the operating status of the projector. Status Power is not connected. POWER ON (green) : Off : Lit LED indicator STAND BY WARN- LAMP (red) ING (red) (orange) : Flashing TEMP (red) Ready to turn power on (standby). Power
  • Canon REALiS WUX4000 | User manual - Page 32
    HDMI IN Terminal (HDMI IN) (P39) Receives the digital content image signal (HDMI). Carries both video and audio signals across a single cable. (1) (2) (3) (4) (5) (6) (7) (5)Service Port (CONTROL) This terminal is used by servicing technicians. It is not used during ordinary use. (6)AUDIO IN
  • Canon REALiS WUX4000 | User manual - Page 33
    MULTIMEDIA PROJECTOR Operation 33
  • Canon REALiS WUX4000 | User manual - Page 34
    34
  • Canon REALiS WUX4000 | User manual - Page 35
    Projecting an Image 35 Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Appendix Index
  • Canon REALiS WUX4000 | User manual - Page 36
    Installation work will be performed by a qualified technician or Canon dealer where the projector was purchased. Connecting the Projector to Equipment (P126) Starting Projection (P43) Do you want to project an image from a notebook computer? Yes No For a notebook computer, turn on the monitor
  • Canon REALiS WUX4000 | User manual - Page 37
    to the computer. Before connecting the cables, turn off both the projector and computer. A digital connection (P38) is recommended when projecting a WUXGA or UXGA image in high quality. When using a computer with an HDMI output terminal, a digital connection (P39) can be made using an HDMI cable
  • Canon REALiS WUX4000 | User manual - Page 38
    15-pin BNC terminal converter cable (not included) Monitor output terminal (mini D-sub 15-pin) BNC cable (not included) When inputting corresponding sound. Projector To ANALOG PC/COMPONENT IN AUDIO OUT terminal (AUDIO OUT) Audio cable (not included) To AUDIO IN • A signal with a dot clock of
  • Canon REALiS WUX4000 | User manual - Page 39
    digital sound is also connected at the same time. ■Outputting Audio to Speakers It is possible to output audio from the projected images to amplified speakers. Projector Speaker To AUDIO OUT RCA terminal Audio cable (not included) Mini jack Audio input terminal (AUDIO IN) Use an audio cable
  • Canon REALiS WUX4000 | User manual - Page 40
    and AV equipment. Before connecting the cables, turn off both the projector and AV equipment. The description provided here is one example. For more detailed information, refer to the manual for the connected AV equipment. ■Connecting to Digital Video Output Terminal (Digital Connection) HDMI
  • Canon REALiS WUX4000 | User manual - Page 41
    Operation Projecting an Image Connecting the Projector ■Connecting to Analog Video Output Terminal (Analog Connection) Component cable (Input signal type: [Component] - P46) A component video signal from the AV equipment can be inputted into the projector by connecting the component cable to the
  • Canon REALiS WUX4000 | User manual - Page 42
    ■Outputting Audio to Speakers It is possible to output audio from the projected images to AV equipment or amplified speakers. Projector Speaker To AUDIO OUT RCA terminal Audio cable (not included) Mini jack Audio input terminal (AUDIO IN) Use an audio cable without a built-in resistor
  • Canon REALiS WUX4000 | User manual - Page 43
    projector and the computer or AV equipment. (P40 - P42) 2 Connect the power cord and make sure that the [STAND BY] indicator is lit (red). Operation Projecting an Image projector, wait at least 5 minutes before turning it on again. It may shorten the lamp life if you turn on the projector
  • Canon REALiS WUX4000 | User manual - Page 44
    the countdown window. (P43) Using the Power Saving Mode (Power Management) When you enable the power management mode, the lamp is automatically turned off if the projector receives no signal input for a certain period of time. (P96) ■When the Language Selection Screen Appears A window appears when
  • Canon REALiS WUX4000 | User manual - Page 45
    , refer to "Changing Notebook Computer Screen Output" below. ■Adjusting Image • For the display resolution of the computer, select "1920 x the model. For details, see the instructions for your notebook computer. • With Windows 7, you can turn on image output by holding down the Windows logo key and
  • Canon REALiS WUX4000 | User manual - Page 46
    the input signal since the last projection. ■Types of Input Signals The table below shows the relationship among input signals supported by the projector, input terminals and connection cables. Input signal Input terminal Types of connection cables HDMI HDMI IN HDMI cable (not included
  • Canon REALiS WUX4000 | User manual - Page 47
    Operation Projecting an Image Selecting an Input Signal (INPUT) ■Selecting an Input Signal 1 Press the INPUT button to display the window shown on the lower right. Remote control Projector The currently active input signal is marked with a circle and highlighted in orange. An input signal that
  • Canon REALiS WUX4000 | User manual - Page 48
    Adjusting the Image Setting the Display Resolution of the Computer Based on the performance of the projector (resolution: 1920 x 1200 pixels), set the display resolution of the computer to "1920 x 1200 pixels" or the resolution closest to the output signal resolution of
  • Canon REALiS WUX4000 | User manual - Page 49
    Auto PC Function Press the AUTO PC button to perform projector adjustment. Remote control If the projected image was not properly adjusted with the Auto PC function, perform pixels] to make adjustments. (P77 - P79) • For the signal types supported by the projector, see the table on page 173. 49
  • Canon REALiS WUX4000 | User manual - Page 50
    change the setting depending on the resolution of the computer. If the image is not projected with the desired aspect ratio, see "Relationship between select the aspect ratio of the projected image. 1 Press the MENU button to display a menu window. Remote control Projector 2 Use the [ ] / [
  • Canon REALiS WUX4000 | User manual - Page 51
    Use the [ ] / [ ] buttons to select the desired contents. Remote control Projector Operation Projecting an Image 16:10 Select this when you use a screen with aspect ratio of 16:10. Also, select this when you project an image on a wall. 16:9 Select this when you use a screen with aspect ratio of
  • Canon REALiS WUX4000 | User manual - Page 52
    on the lower right. Remote control 2 Use the [ ] / [ ] buttons to move the image. The minimum value is -60, and the maximum value is +60. Remote control Projector [ ] button Moves image up [ ] button Moves image down 3 When image shift adjustment has been completed, press the OK button. 52
  • Canon REALiS WUX4000 | User manual - Page 53
    the lower right. Remote control 2 Use [ ] / [ ] to move the image. The minimum value is -60, and the maximum value is +60. Remote control Projector [ ] button Moves the image left [ ] button Moves the image right 3 When image shift adjustment has been completed, press the OK button. Resetting
  • Canon REALiS WUX4000 | User manual - Page 54
    projecting visual software which has an aspect ratio of 4:3 and black bars at the top and bottom of the image. • This mode is available when you select [16:10], [16:9] or [16:9 D. image shift] for [Screen aspect] and select [HDMI (480p, 576p)] or [Component (480p, 480i, 576p, 576i)]. True size The
  • Canon REALiS WUX4000 | User manual - Page 55
    type. For more details on the aspect ratios, refer to page 171 "Relationship between Aspect and Screen Aspect". Remote control Example: Operation Projecting an Image You can also select any aspect ratio from the menu. (P75) Some aspect ratios may not appear depending on the type of input signal
  • Canon REALiS WUX4000 | User manual - Page 56
    can be adjusted by pressing the ZOOM button on the remote control or the LENS button on the projector. Change the projector installation position if your desired image is too large or too small to adjust it with the zoom function. (P123) 1 Press either the ZOOM button on the remote controller or
  • Canon REALiS WUX4000 | User manual - Page 57
    To adjust the focus, press the FOCUS button on the remote control or the LENS button on the projector. With the Standard Zoom Lens / Long Zoom Lens / Short Fixed Lens, the projection image may be out of focus if the projection distance is not within the range of approx. 1.3 m - 9.6 m (4.3' - 31
  • Canon REALiS WUX4000 | User manual - Page 58
    , or right, press the LENS-SHIFT button on the remote control or the LENS button on the projector. This function is referred to as "lens shift" because the position of the projected image is changed by moving the lens position. • The available range for lens shift (percentage of movement relative
  • Canon REALiS WUX4000 | User manual - Page 59
    The result of keystone adjustment is stored in memory. If you place the projector in the same position, the keystone adjustment is not necessary. • Signals are processed digitally when keystone distortion is corrected. The image may look different from the original one. In addition, the aspect ratio
  • Canon REALiS WUX4000 | User manual - Page 60
    Adjusting the Image 1 Press the D.SHIFT/KEYSTONE button to display the window shown on the lower right. Remote control 2 Press the pointer buttons to adjust. Remote control Projector [ ] button Reduces the length of the upper edge [ ] button Reduces the length of the lower edge [ ] button
  • Canon REALiS WUX4000 | User manual - Page 61
    Operation Projecting an Image Adjusting the Image ■Resetting the Keystone Adjustment Perform the following steps to reset the keystone adjustment. Press the D.SHIFT/KEYSTONE button twice to display the [Keystone reset] window.
  • Canon REALiS WUX4000 | User manual - Page 62
    the brightness, contrast, sharpness, gamma, color adjustment, advanced adjustment, and lamp mode. (P86) ■Image Modes The image modes which can be selected vary somewhat depending on the selected input signal. Image Mode Compatible input signals Digital PC Analog PC HDMI ([Computer]) Component
  • Canon REALiS WUX4000 | User manual - Page 63
    button on the remote control to select. The image mode changes each time the IMAGE button is pressed. (The displayed image modes vary depending on the selected input signal.) Remote control You can also select any image mode from the [Image mode] menu. (P86) • User settings 1 - 5 are displayed when
  • Canon REALiS WUX4000 | User manual - Page 64
    , wait at least 5 minutes before turning it on again. It may shorten the lamp life if you turn on the projector immediately after turning it off. • Using the projector for a long time may shorten the life of the lamp and internal optical components. 2 Disconnect the power cord from the AC outlet. If
  • Canon REALiS WUX4000 | User manual - Page 65
    Useful Functions Available During a Presentation Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance
  • Canon REALiS WUX4000 | User manual - Page 66
    again to show the • You can set the screen state while blacking out the image on the menu. (P84) • The lamp remains illuminated while the image is blacked out. Press the button to freeze the moving image. The projector shows the following icon. Press the button again to cancel the FREEZE function
  • Canon REALiS WUX4000 | User manual - Page 67
    Useful Functions Available During a Presentation Adjusting the Volume Muting the Sound Useful when: • You want to adjust the volume level of the projector or external speakers. Remote control Useful when: • You want to temporality mute unnecessary sound. • You want to immediately mute the sound
  • Canon REALiS WUX4000 | User manual - Page 68
    : • Zooming in on an object such as a small graph during a presentation (up to 12x). • Focusing on the current subject. Press the button. A part of the image is enlarged each time the button is pressed. Remote control You can move the enlarged area by using the buttons. Remote control
  • Canon REALiS WUX4000 | User manual - Page 69
    Useful Functions Available During a Presentation Showing the Elapsed Time Useful when: • You want to manage the timing of the presentation. Operation Useful Functions Available During a Presentation Press the button to start counting. • The elapsed time is displayed on the lower right corner of
  • Canon REALiS WUX4000 | User manual - Page 70
    70
  • Canon REALiS WUX4000 | User manual - Page 71
    Setting Functions from Menus Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Appendix Index 71
  • Canon REALiS WUX4000 | User manual - Page 72
    refer to "Installation and Maintenance". preference. [Information] tab (P108) You can check information about the signal types of the images projected and other projector-specific informa- tion. Contents of menu Menu items Input Signal Types for which a Menu Item is Displayed Different menu
  • Canon REALiS WUX4000 | User manual - Page 73
    to Use Menus ■Basic Operation of Menu 1 Press the [MENU] button to display the menu window. Remote control Projector 2 Use the [ ] / [ ] buttons to select a tab. Remote control Projector • If the tab position is not highlighted in orange, use the [ ] / [ ] buttons to move the highlight to
  • Canon REALiS WUX4000 | User manual - Page 74
    the setting. Selecting from a different screen (1) Example: Menu position 1. Press the OK button to display a different screen. 2. Then follow the instruction on the screen. Selecting from a different screen (2) Example: Tracking 1. Press the OK button to display a different screen. 2. Use the
  • Canon REALiS WUX4000 | User manual - Page 75
    Projection Mode [Aspect] HDMI Digital PC Component Analog PC You can select a projection mode corresponding to the aspect ratio of the image. (P54) Display settings Aspect • Different contents are displayed for different screen aspects or input signal types. • The ASPECT button on the remote
  • Canon REALiS WUX4000 | User manual - Page 76
    (P49) cannot project the correct image from a computer. Display settings Input the proper component signal type if the video image from AV equipment is not projected correctly. resolution of the computer. • For the signal types supported by the projector, see the table on page 173. Press the OK
  • Canon REALiS WUX4000 | User manual - Page 77
    you have completed the adjustment, press the MENU button. • Perform this adjustment if the [AUTO PC] function (P49) cannot adjust the projected image correctly. Use [ ] / [ ] to select a value. When you have completed the adjustment, press the MENU button. • Perform this adjustment if the [AUTO PC
  • Canon REALiS WUX4000 | User manual - Page 78
    you have completed the adjustment, press the MENU button. • Perform this adjustment if the [AUTO PC] function (P49) cannot adjust the projected image correctly. When you have completed the adjustment, press the MENU button. • Perform this adjustment if the [AUTO PC] function (P49) cannot adjust
  • Canon REALiS WUX4000 | User manual - Page 79
    you have completed the adjustment, press the MENU button. • Perform this adjustment if the [AUTO PC] function (P49) cannot adjust the projected image correctly. When you have completed the adjustment, press the MENU button. • Perform this adjustment if the [AUTO PC] function (P49) cannot adjust
  • Canon REALiS WUX4000 | User manual - Page 80
    in [Auto] mode. (Some AV equipment may not support this.) • If the HDMI output of your AV equipment recommend you to set [Expanded]. The contrast of images will be improved and dark scenes will be rendered to the User's Manual of the AV equipment connected to the projector. Auto RGB YCbCr Select
  • Canon REALiS WUX4000 | User manual - Page 81
    Display Status Performing Progressive Processing [Progressive] HDMI Digital PC Component Analog PC You can select this as required when the images have low resolution. Display settings Progressive Operation Setting Functions from Menus Off The entire input signal (100%) is projected. The
  • Canon REALiS WUX4000 | User manual - Page 82
    to the desired position, press the OK or MENU button. Normal Greenboard Adjust Select this if a standard type of projection screen is used. The images are projected in a light quality similar to that of natural light. Select this if a Greenboard (dark green color) is used for the projection screen
  • Canon REALiS WUX4000 | User manual - Page 83
    • [None] is the factory default. Rear ceiling mounted projection • To hang the projector from the ceiling, use the optional bracket. Contact a Canon dealer where you purchased the projector for more detailed information. • If you flip the image, the keystone distortion adjustment will be reset. 83
  • Canon REALiS WUX4000 | User manual - Page 84
    settings] - [Screen when blank] HDMI Digital PC Component Analog PC You can display a black or blue screen and temporarily blank out the projected image by pressing the BLANK button on the remote control. Display settings User screen settings Screen when blank Black Blue The screen is all
  • Canon REALiS WUX4000 | User manual - Page 85
    after turning on the projector. Displays the Canon logo that was registered in advance at the factory. Press the OK button to accept your setting and then press the MENU button. • [Canon logo] is the factory default. 16:10 16:9 4:3 16:9 D. image shift 4:3 D. image shift Select this when
  • Canon REALiS WUX4000 | User manual - Page 86
    when using the projector in a dimly lit room. User 1 - 5 Up to 5 user-selected combina- tions of image quality settings can be image quality by adjusting the following items in each image mode: [Brightness], [Contrast], [Sharpness], [Gamma], [Color adjustment], [Advanced adjustment] and [Lamp
  • Canon REALiS WUX4000 | User manual - Page 87
    quality settings can be stored. The stored image quality can be selected as an image mode. Image adjustment Create Profile • The saved settings consist of the brightness, contract, sharpness, gamma, color adjustment, advanced adjustment, and lamp mode. • The number of displayed user memories
  • Canon REALiS WUX4000 | User manual - Page 88
    less vivid, adjust the difference in tone between the lightest and darkest portions of the image. Image adjustment Contrast [ ] Increases the brightness of an image. [ ] Decreases the brightness of an image. When you have completed the adjustment, press the MENU button. • The adjustment you have
  • Canon REALiS WUX4000 | User manual - Page 89
    you have completed the adjustment, press the MENU button. • The adjustment you have made is stored as adjusted values for the input signals and image mode of the current projection. [ ] Brightens the dark portion [ ] Darkens the bright portion When you have completed the adjustment, press the MENU
  • Canon REALiS WUX4000 | User manual - Page 90
    intensity of color. Color Adjusts the color balance of a reddish balance or greenish image. [ ] Corrects a reddish image. [ ] Corrects a greenish image. Color Adjusts the color temperature of the temper- image. ature [ ] Changes to a bluish color (cold color). [ ] Changes to a reddish color (warm
  • Canon REALiS WUX4000 | User manual - Page 91
    this if the ambient light is normal. H Select this if the ambient light is high. Operation Setting Functions from Menus Off Adjust Projects an image with no correction. You can specify the type and level (brightness) of the ambient light. Examples of Ambient Light Settings Level Example Location
  • Canon REALiS WUX4000 | User manual - Page 92
    gamma] HDMI Digital PC Component Analog PC You can adjust the gradation representation of light and dark portions of an image automatically. Image adjustment Advanced adjustment Dynamic gamma Off Weak Middle Strong Disables noise reduction. Specifies the intensity of the noise reduction in
  • Canon REALiS WUX4000 | User manual - Page 93
    MENU button. • [Off] is the factory default. • The adjustment you have made is stored as adjusted values for the input signals and image mode of the current projection. Reset Use the [ ] / [ ] buttons to select [ Hue], [ Saturation], or [* Brightness], then adjust them with the [ ] / [ ] buttons
  • Canon REALiS WUX4000 | User manual - Page 94
    . When you have completed the adjustment, press the OK button. • The adjustments you have made are stored as adjusted values for the input signals and image mode of the current projection. • For the details of gamma correction, refer to page 89. Fine-Tune Gamma Select [Fine-Tune Gamma] then press
  • Canon REALiS WUX4000 | User manual - Page 95
    reduces power consumption and cooling fan noise. You can also enable or disable this mode with the LAMP button on the remote control. Image adjustment Lamp mode Selecting an Image Quality Resetting the Image Settings [Reset] HDMI Digital PC Component Analog PC You can reset the current
  • Canon REALiS WUX4000 | User manual - Page 96
    Direct power on Off Standby Exit Disables the power management mode. If no input signal is received for 30 seconds, the projector enters the standby mode, turning off the lamp five minutes after start of countdown. If it receives an input signal or is operated during this period of 30 seconds
  • Canon REALiS WUX4000 | User manual - Page 97
    ] is the factory default. • The beep will not sound if you mute the projector sound with the MUTE button on the remote control. Off Disables the key lock. which is not locked. To Unlock Key Lock Function Turn off the projector and unplug the power plug. Hold down the OK button on the side
  • Canon REALiS WUX4000 | User manual - Page 98
    OK button and MENU button at the same time for 3 seconds. Ch1 Ch2 Ch3 Ch4 Independent Select the remote control channel to use with this projector. Remote controls set to any channel can be used. Press the OK button to accept your setting and then press the MENU button. • The factory
  • Canon REALiS WUX4000 | User manual - Page 99
    Swedish Russian Dutch Finnish Norwegian Turkish Polish Hungarian Czech Danish Arabic Chinese (Simplified) Chinese (Traditional) Korean Japanese Off Hides the guide screen. On Shows the guide screen. Press the OK button to accept your setting and then press the MENU button. • [On] is the factory
  • Canon REALiS WUX4000 | User manual - Page 100
    button to accept your setting and then press the MENU button. • [On] is the factory default. Auto Computer Select when AV equipment will be connected. Image processing, menu displays, and other elements are adjusted for video equipment. Select when a computer will be connected
  • Canon REALiS WUX4000 | User manual - Page 101
    unless the correct password is entered. System settings Other settings Password settings Setting Various Functions To Cancel the Password Turn off the projector and unplug the power plug. Hold down the MENU button on the side control and connect the power plug. Make sure to keep holding
  • Canon REALiS WUX4000 | User manual - Page 102
    Setting Various Functions Registering a Password [Other settings] - [Register password] HDMI Digital PC Component Analog PC You can register a password for starting projection. System settings Other settings Register password Prohibiting Operation of the Lens [Other settings] - [Lens Ctrl
  • Canon REALiS WUX4000 | User manual - Page 103
    (P56) -Focus adjustment (P57) -Keystone adjustment (P59) -Keystone reset (P61) -D.image shift adjustment (P52, P53) -D.image shift reset (P53) 4 to 10 seconds -Aspect (P55) -Image mode (P62) -Volume adjustment (P67) -Lamp mode (P95) 3 minutes -Lens shift (P58) -Lens shift reset (P103
  • Canon REALiS WUX4000 | User manual - Page 104
    adjusts the image display in order to reduce flickering in the projected image. • Deflicker can only be used when the lamp has been warning] icon shown below will be displayed when the temperature inside the projector is abnormally high. Off Deflicker adjustment is not performed. Select [
  • Canon REALiS WUX4000 | User manual - Page 105
    deflicker is performed, the image adjustment screen is projected for approximately 20 seconds. • To cancel deflicker, press the POWER button. Resetting the Lamp Counter [Other settings] - [Lamp counter] HDMI Digital PC Component Analog PC You can reset the lamp counter that indicates the time
  • Canon REALiS WUX4000 | User manual - Page 106
    bar. Select [OK] on the screen for confirmation and press the OK button to reset the lamp counter. Press the MENU button. ■ About the Display of the Lamp Counter The lamp counter displays the hours of use of the lamp in the following way. Less than 2,700 hours Displayed as a green bar. The message
  • Canon REALiS WUX4000 | User manual - Page 107
    the OK button to accept your setting and then press the MENU button. • This function does not reset the values for [Lamp counter], [Language], [Remote control], [Input signal], [Network Setting], [Filter counter], [Focus position], [Zoom position], and [Lens shift position]. • For factory defaults
  • Canon REALiS WUX4000 | User manual - Page 108
    Information [Information] HDMI Digital PC Component Analog PC You can confirm information about the signal types of the images projected and other projector-specific information. Information Information shown Item Model name Input signal Firmware Serial No. IP address* Gateway address* E-mail
  • Canon REALiS WUX4000 | User manual - Page 109
    MULTIMEDIA PROJECTOR Installation and Maintenance Do not attempt installation yourself. Be sure to request installation from a qualified technician or Canon dealer. 109
  • Canon REALiS WUX4000 | User manual - Page 110
    110
  • Canon REALiS WUX4000 | User manual - Page 111
    Installation 111 Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Appendix Index
  • Canon REALiS WUX4000 | User manual - Page 112
    grasp the lens while transporting it. Doing so may damage the projector. Installation Precautions Be sure to read "Safety Instructions" on page 10 - 22. Pay attention to the following when installing the projector. • Do not strike the projector or subject it to impact. Doing so Intake may cause
  • Canon REALiS WUX4000 | User manual - Page 113
    50 cm (1.6') to the rear.) ■ Be Careful of Condensation If the temperature of the room rises suddenly, moisture in the air may condense on the projector lens and mirror, causing the image to become blurred. Wait until condensation evaporates and a normal picture is shown. 113
  • Canon REALiS WUX4000 | User manual - Page 114
    of 360° *1 as shown in the illustration below. However, if projecting upward or downward, the life span of the lamp may be shortened. ˃ ˃ ˃ ˃ Downward projection: Inclination of the projector should be no more than 10° from the vertical axis. *2 Upward projection: Inclination of the
  • Canon REALiS WUX4000 | User manual - Page 115
    Installation Procedure Selecting the Projection Method and Installation Location (P116) Installing/Removing the Lens Unit (P117) Setting Up the Projector (P122) Connecting to AV Equipment (P126) Selecting an Input Signal (P46) Adjusting the Image (P48) Connecting to a Network (P129) 115
  • Canon REALiS WUX4000 | User manual - Page 116
    on a Flat Surface When the screen is in a higher position, point the projector up using the adjustable feet. You can incline it upwards to a maximum of 6°. When the projector is inclined upwards, the projected image will be distorted into a trapezoid shape. This can be corrected by using the
  • Canon REALiS WUX4000 | User manual - Page 117
    picture quality. • For details about which devices the projector is compatible with, contact a Canon dealer. 1 Use a Phillips-head screwdriver and loosen the lamp cover screw, then open the lamp cover. The lamp cover screw is attached to the lamp cover and designed to prevent it from falling off
  • Canon REALiS WUX4000 | User manual - Page 118
    . The cosmetic panel screw is attached to the cosmetic panel and designed to prevent it from falling off. 3 In order to prevent damage, close the lamp cover and temporarily fasten the screw. 4 Remove the sleeve screws (2 on top and 2 on bottom). After the 2 screws on top are removed, turn the
  • Canon REALiS WUX4000 | User manual - Page 119
    back over and remove the sleeve. 6 Referring the following illustration, insert the lens connector of the lens unit into the front right side of the projector slowly until it contacts the end. At this time, pull out the lens cable shown in the illustration and fix it. Lens cable Lens connector
  • Canon REALiS WUX4000 | User manual - Page 120
    Installing/Removing the Lens Unit 8 Insert the projector lens cable into the connector until a click sound is heard. 9 Return the sleeve, cosmetic panel, and lamp cover to their original conditions. When the power is first turned on after the lens unit is replaced, the initialization operation will
  • Canon REALiS WUX4000 | User manual - Page 121
    Installation and Maintenance Installation Installing/Removing the Lens Unit ■Removing the Lens Unit 1 Perform steps 1 to 5 of "Installing the Lens Unit" (P117 - P119) and remove the sleeve. 2 Disconnect the lens cable from the lens connector. When pulling out (disconnecting) the lens cable, press
  • Canon REALiS WUX4000 | User manual - Page 122
    , and other steps taken to make the screen easier to see. Screen Optical axis ■Relationship Between Image Size and Projecting Distance The projected image size is determined by the distance between the projector and the screen (projection distance) as well as the zoom. Refer to the table below and
  • Canon REALiS WUX4000 | User manual - Page 123
    Installation and Maintenance Installation Setting Up the Projector Lens unit Diagonal Image size (cm) Projection distance Distance from optical when axis when projection is 16:10 (diagonal) 16:10 16:9 4:3 Zoom Zoom Maximum Minimum perpendicular to screen* (
  • Canon REALiS WUX4000 | User manual - Page 124
    Setting Up the Projector ■Lens Shift Function The projector includes a lens shift function. Operation of the buttons slides the lens up, down, left, and right, moving the image position. For the function operations, refer to "Adjusting the Image Position" (P58). The amount of lens shift is indicated
  • Canon REALiS WUX4000 | User manual - Page 125
    Setting Up the Projector ˃ Moves right by up to approximately 10% of the image width. Installation and Maintenance Installation At maximum rightward lens shift Area where lens movement is not possible With the Standard Zoom Lens and Long Zoom
  • Canon REALiS WUX4000 | User manual - Page 126
    connect to a PC. Computer (P39) * Select playback mode before connecting. LAN terminal Network (P130) Service port (not normally used) AUDIO IN terminal AUDIO OUT terminal Audio signal for each image input (P37, P38, P41) Analog PC/ Component Amplified speakers (P39, P42) (P38) Digital PC
  • Canon REALiS WUX4000 | User manual - Page 127
    Installation and Maintenance Installation Connecting to AV Equipment ■Connection Terminal and Connection Cable Input signal HDMI Input terminal HDMI IN Types of connection cables HDMI cable (not included) Digital PC DVI-D IN DVI digital cable (LV-CA29, option) VGA cable (supplied item)
  • Canon REALiS WUX4000 | User manual - Page 128
    128
  • Canon REALiS WUX4000 | User manual - Page 129
    Connecting to a Network Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Appendix Index 129
  • Canon REALiS WUX4000 | User manual - Page 130
    IP address is not overlapped with other computers that are on the same LAN. When you set the IP address of the projector, follow the instruction in "Configuring the Network from the Computer" (P140) on the web screen or refer to "TCP/IP Setting" (P139). • When you connect the computer to
  • Canon REALiS WUX4000 | User manual - Page 131
    mask, default gateway, etc). 6 Select [Use the following IP address] and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. Example IP address:192.168.254.1 Subnet mask: 255.255.255
  • Canon REALiS WUX4000 | User manual - Page 132
    mask, default gateway, etc). 6 Select [Use the following IP address] and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. Example IP address:192.168.254.1 Subnet mask: 255.255.255
  • Canon REALiS WUX4000 | User manual - Page 133
    mask, default gateway, etc). 5 Select [Use the following IP address] and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. Example IP address:192.168.254.1 Subnet mask: 255.255.255
  • Canon REALiS WUX4000 | User manual - Page 134
    , subnet mask, router, DNS server, etc.). 4 Create a new network environment and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. Example IP address:192.168.254.1 Subnet mask: 255.255.255
  • Canon REALiS WUX4000 | User manual - Page 135
    Network Settings on the Projector From the projector menus screen, network settings can be configured on the [Network Setting] tab. For the menu operations, refer to "How to Use Menus" (P72). Locking the
  • Canon REALiS WUX4000 | User manual - Page 136
    function Setting a Network Password [Network Password setting] You can set whether or not a password is required in order to change the projector network settings. Network Setting Network Password setting Off Disables the network function. On Enables the network function. Press the OK button to
  • Canon REALiS WUX4000 | User manual - Page 137
    conforms to Class 1 as defined in the PJLink standards of the JBMIA (Japan Business Machine and Information System Industries Association). This projector supports all commands that are defined by PJLink Class 1, and has been verified as conforming to the PJLink standard Class 1 definition. • For
  • Canon REALiS WUX4000 | User manual - Page 138
    Standardization of control and monitoring specifications for basic projector functions Basic projector control: Power control, input selection, etc. Acquisition of projector information and status: Power status, input selection status, error status, lamp use time, etc. JBMIA: Japan Business Machine
  • Canon REALiS WUX4000 | User manual - Page 139
    TCP/IP settings. Network Setting TCP/IP setting Initializing Network Settings [Network setting initialization] You can initialize the projector network settings. Network Setting Network setting initialization Installation and Maintenance Connecting to a Network When [TCP/IP setting] is selected
  • Canon REALiS WUX4000 | User manual - Page 140
    default IP address is "192.168.254.254". If DHCP settings are used, ask the network administrator for the projector IP address. It is possible to check the IP address from the projector menu. 3 Enter the user name and password on the password input screen, then click OK. The factory default user
  • Canon REALiS WUX4000 | User manual - Page 141
    The name of the projector on the network The location of projector installation The MAC address of the projector The IP address of the projector The power status of the projector Lamp operating time in [Normal] lamp mode Lamp operating time in [Quiet] lamp mode Lamp operating time (converted value
  • Canon REALiS WUX4000 | User manual - Page 142
    the displayed field (2) and click [OK] (3). (1) (2) (3) 6 A confirmation window appears. Check the contents and if they are correct, click [Apply]. The settings are applied to the projector and "Save completed" is displayed. 7 Click [Back to top] to return the web screen to the initial page. 142
  • Canon REALiS WUX4000 | User manual - Page 143
    Installation and Maintenance Connecting to a Network Configuring the Network From the Computer ■Resetting to Factory Defaults 1 Perform steps 1 - 3 of "Displaying and Configuring the Network Configuration Screen" (P140) to display the setting window. 2 Click [Initialize]. 3 A confirmation window
  • Canon REALiS WUX4000 | User manual - Page 144
    connect to the POP3 server attempting to send a test mail. An authentication type was set which is not supported by the server. Authentication failed attempting to send a test mail. Sending of test mail failed due to when settings were changed at the same time from multiple projectors. 144
  • Canon REALiS WUX4000 | User manual - Page 145
    Setting Up the Network ■Setting Basic Information [Network] From [Network] in the settings window, you can log into the web screen and set basic network information. For the setting procedure, refer to "Displaying and Configuring the Network Configuration Screen" (P140). Installation and
  • Canon REALiS WUX4000 | User manual - Page 146
    the SNTP server IP address in 1-byte numbers. Select the time zone where the projector is used. Enter the interval for resending mail when an error occurred (units: seconds default setting MailUserAccount [email protected] 0.0.0.0 25 0.0.0.0 (GMT) Dublin, Lisbon, London 10 3 OFF
  • Canon REALiS WUX4000 | User manual - Page 147
    Setting Up the Network ■Mail Authentication Settings [Mail auth] From [Mail auth] in the settings window, you can configure the settings for authentication of mail that is sent when an error occurs. For the setting procedure, refer to "Displaying and Configuring the Network Configuration Screen" (
  • Canon REALiS WUX4000 | User manual - Page 148
    settings window (P146) is displayed. The sender name which was set from [Mail] in the settings window (P146) is displayed. The predetermined mail title "Canon Projector test" is displayed. ■SNMP Settings [SNMP] From [SNMP] in the settings window, you can configure the settings related to control of
  • Canon REALiS WUX4000 | User manual - Page 149
    and Configuring the Network Configuration Screen" (P140). Installation and Maintenance Connecting to a Network Item Projector name Location Explanation Factory default setting Enter the projector name in 1-byte alphanu- WUX4000 meric characters and symbols (1 - 63 char- acters). Enter the
  • Canon REALiS WUX4000 | User manual - Page 150
    Network ■Setting PJLink [PJLink] From [PJLink] in the setting window, you can set the PJLink functions which are the standard for projector management on a network. For the setting procedure, refer to "Displaying and Configuring the Network Configuration Screen" (P140). For information about PJLink
  • Canon REALiS WUX4000 | User manual - Page 151
    . The password input screen appears. The factory default IP address is "192.168.254.254". It is possible to check the IP address from the projector menu. 3 Enter the user name and password on the password input screen, then click OK. The factory default user name is "root" and the password
  • Canon REALiS WUX4000 | User manual - Page 152
    Controlling the Projector from a Computer 5 The projector control screen appears. The projector can be controlled from this screen. Item Projector name IP address Refresh Power Input Aspect Image mode Blank Mute Auto PC Information Explanation The name of the connected projector is displayed. (
  • Canon REALiS WUX4000 | User manual - Page 153
    . If the problem is inside the projector, check whether the projector is installed and operated normally, turn off the projector to cool its inside, and retry projection. If the same warning occurs again, the projector may be defective. Contact your Canon dealer. Faulty lamp The lamp has burnt out
  • Canon REALiS WUX4000 | User manual - Page 154
    154
  • Canon REALiS WUX4000 | User manual - Page 155
    Maintenance 155 Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Appendix Index
  • Canon REALiS WUX4000 | User manual - Page 156
    image. • When cleaning the projector, make sure to turn off the projector, wait until the cooling fan stops, disconnect the power plug from the AC outlet, and let the projector projector. • When using a chemical dust cloth, make sure to read the instructions thoroughly. • When cleaning the projector
  • Canon REALiS WUX4000 | User manual - Page 157
    and remove the power plug. 2 Hook your finger onto the handle of the air filter on the side of the projector, and pull the air filter out to remove it. Air filter 3 Remove the filter from the air filter frame. First disengage the tab on the
  • Canon REALiS WUX4000 | User manual - Page 158
    the way into the projector. • Handle the air filter carefully. If damaged, the air filter will not work properly. • When the lamp is replaced, it is recommend that you also replace the air filter. • An air filter can be ordered from your Canon dealer. • Replacement
  • Canon REALiS WUX4000 | User manual - Page 159
    exceeds a certain amount of time, the following message (two types) is displayed for 10 seconds every time the projector is turned on. 2,700 hours to less than 3,000 hours Prepare the new lamp when this screen is displayed. • Only the [ ], [ ], OK and POWER buttons are available while this screen is
  • Canon REALiS WUX4000 | User manual - Page 160
    impact. If the lamp breaks, contact your Canon dealer and follow the instructions in "Precautions on the lamp" (P19) and "Lamp handling precautions" (P20). • When replacing the lamp, do not remove any screws other than those specified. Replacing the Lamp 1 Turn off the projector power and remove the
  • Canon REALiS WUX4000 | User manual - Page 161
    unit in the direction of the arrow. Even when the screws are loosened, they will not fall off the lamp unit. 4 Fully insert a new lamp unit and secure it with the 3 screws. 5 Close the lamp cover and tighten the screws. 6 Turn on the power. Bring up the menu and select [System settings] - [Other
  • Canon REALiS WUX4000 | User manual - Page 162
    Replacing the Lamp 7 Select [Reset] - [OK] to reset the lamp counter. 162
  • Canon REALiS WUX4000 | User manual - Page 163
    MULTIMEDIA PROJECTOR Appendix 163
  • Canon REALiS WUX4000 | User manual - Page 164
    164
  • Canon REALiS WUX4000 | User manual - Page 165
    Appendix 165 Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Appendix Index
  • Canon REALiS WUX4000 | User manual - Page 166
    Troubleshooting LED Indicator Meanings When there is a problem with the projector, the LED indicator on the side of the projector flashes continuously after the projector malfunction in the projector. Contact your Canon dealer. WARNING and Faulty lamp LAMP are lit. The lamp does not illuminate.
  • Canon REALiS WUX4000 | User manual - Page 167
    intake or exhaust vent and contact your Canon dealer. Check whether the lens connector is connected correctly. (P120) Check whether the air filter is installed correctly. (P157) Appendix Other Information ■You Cannot Project an Image from the Projector Cause A connection cable is not connected
  • Canon REALiS WUX4000 | User manual - Page 168
    Troubleshooting Cause The BLANK function has been selected. No image is projected due to a problem with the computer. The external monitor output is not set on the notebook computer correctly. The displayed image detailed information, refer to the User's Manual that came with your computer. Check
  • Canon REALiS WUX4000 | User manual - Page 169
    Troubleshooting ■The Projected Image Is Blurred Cause Countermeasure The image is out of focus. Adjust the focus. (P57) The distance to the screen is too short. Check whether the distance to the screen is appropriate. If the distance is shorter than approximately 1.3 m (4.3'), the projector
  • Canon REALiS WUX4000 | User manual - Page 170
    Troubleshooting Cause The lamp has broken (or there is a lamp malfunction). The operating temperature is inappropriate. Other reasons Countermeasure Check whether the lamp has broken. If the lamp has broken, follow the instructions in "Precautions on the lamp" on page 19. If the lamp has not
  • Canon REALiS WUX4000 | User manual - Page 171
    Relationship between Aspect and Screen Aspect This section describes the relationship between screen aspect (P50) and aspect (P54). To project an image on the whole screen, select the most appropriate screen aspect ratio and aspect according to the aspect ratio of the screen and input signal type.
  • Canon REALiS WUX4000 | User manual - Page 172
    so that it is projected on the entire screen by selecting [Zoom] in [Aspect]. [Zoom] is available when [16:10], [16:9] or [16:9 D. image shift] is selected for the screen aspect and [HDMI (480p, 576p)] or [Component (480p, 480i, 576p, 576i)] is selected for the input signal. • To perform
  • Canon REALiS WUX4000 | User manual - Page 173
    Signal Types This projector supports the following signal types. If your computer or AV equipment is compatible with any one of these signal types, the projector's Auto PC function selects the input signal type to project an image appropri- ately. ANALOG RGB HDMI Resolution (dots) 640
  • Canon REALiS WUX4000 | User manual - Page 174
    Projector Model name Display system Optical system Type WUX4000 V: -15% - +55%, H: ±10% Light source Image size (projection distance) (*1) Number of colors Brightness Contrast ratio cord, PC connection cable, User's Manual / Installation Manual, warranty certificate *1 When standard zoom lens
  • Canon REALiS WUX4000 | User manual - Page 175
    Product Specifications ■Specification of Each Lens Unit (Option) Name Standard Zoom Lens Long Zoom Lens Model number RS-IL01ST RS-IL02LZ External View Short Fixed Lens RS-IL03WF Focal length F number Projection distance Lens shift Vertical Horizontal Width Height Length Weight Zoom ratio
  • Canon REALiS WUX4000 | User manual - Page 176
    Product Specifications ■External View 9901mmmm (3.5'') 117700 mmmm (6.7'') 92 mm 92(3m.6m'') 43403m0mm(m16.9'') 38308m0mm(m15.0'') Bolt holes (M4 x 6) for installation of ceiling attachment 12812m8mm(5m.0'') 2342.354m.5mm(9m.2'') 53 mm 5(32.m1'm') 21221m2mm(8m.4'') (6.1'') 114411..55 mmmm
  • Canon REALiS WUX4000 | User manual - Page 177
    ■Service Port (CONTROL) Pin assignment Product Specifications Pin No. 1 2 3 4 5 6 7 8 9 Signal off Power status acquisition Input source Digital PC Digital Video Analog PC Component Input source acquisition Image mode STANDARD ASCII representation POWER ON POWER OFF GET POWER INPUT
  • Canon REALiS WUX4000 | User manual - Page 178
    GET IMAGE BRI= GET BRI SHARP= GET SHARP CONT= GET CONT ASPECT=AUTO 4:3 ASPECT=4:3 16:9 Zoom ASPECT=16:9 ASPECT=ZOOM True size ASPECT=TRUE Full Aspect value acquisition Lamp mode Normal ASPECT=FULL GET ASPECT
  • Canon REALiS WUX4000 | User manual - Page 179
    Product Specifications 179 Appendix Other Information
  • Canon REALiS WUX4000 | User manual - Page 180
    66 G Guide 99 H Image adjustment menu 72 Image mode 86 Image Mode (Image Quality 62 Information 72, 108 INPUT 47 Input signal select 46, 76 Input Terminal 32 Connecting to AV Equipment 40 Connection to Computer 37 K Key lock 97 Keystone 59 L LAMP 95 Lamp counter 105 Lamp mode 95 Lamp
  • Canon REALiS WUX4000 | User manual - Page 181
    (settings) .... 96 Power Saving (Power Management) ..... 44 Progressive 81 Projector on 85 P-TIMER 69 R Rear projection 83 Register Network Password 137 Screen when blank 84 Selecting a language 44, 99 Selecting an Image Quality 86 Setting a network password 136 Setting Display Status 75
  • Canon REALiS WUX4000 | User manual - Page 182
    • Lamp Part No materials to hang the projector from the ceiling. For details, refer to the assembly and installation manual provided with the ceiling attachment projector by replacing the lens unit. Regarding installation and replacement of the lens unit, contact a qualified technician or Canon
  • Canon REALiS WUX4000 | User manual - Page 183
    Rear, Ceiling mounted User screen settings P76 No signal screen Black P84 Blue* Screen when blank Black * P84 Blue P76 Projector on Return Skip P85 Canon logo* Screen Aspect 16:10* P85 16:9 4:3 16:9 D. image shift 4:3 D. image shift P77 P77 P78 P78 P79 P79 P80 P80 P81 183
  • Canon REALiS WUX4000 | User manual - Page 184
    /HDMI P86 Dynamic Video Cinema Create Profile P87 Baseline Image P87 Mode (when user memory is selected) Brightness adjust Off * Adjust Reset P93 Hue/Saturation/ Brightness Fine-Tune Gamma P94 Return Lamp mode Normal * P95 Quiet Reset OK/Cancel P95 * : Factory defaults (
  • Canon REALiS WUX4000 | User manual - Page 185
    power on Beep Key lock Remote control Language Guide Off * P96 Standby Exit Off * P96 mail sender address E-mail recipient address Projector name Location System information ID P103 Menu display time Overheat Warning Display Deflicker Lamp counter Factory defaults Return Normal * Extended
  • Canon REALiS WUX4000 | User manual - Page 186
    CO., LTD. 19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong CANON SINGAPORE PTE. LTD. 1 HarbourFront Avenue, #04-01 Keppel Bay Tower, Singapore 098632 CANON KOREA CONSUMER IMAGING INC. Gangnam Finance Center 17F,737,YeoksamDong, Gangnam-gu, Seoul, 135-984, Korea OCEANIA
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Installation
Connecting to a Network
Maintenance
Appendix
Index
Appendix
Installation and Maintenance
Projecting an Image
Safety Instructions
Before Use
Table of Contents
Setting Functions from Menus
Operation
Useful Functions Available
During a Presentation
ENG
MULTIMEDIA PROJECTOR
User’s Manual/
Installation
Manual