Cisco 12406 Configuration Guide
Cisco 12406 Manual
 |
UPC - 882658103230
View all Cisco 12406 manuals
Add to My Manuals
Save this manual to your list of manuals |
Cisco 12406 manual content summary:
- Cisco 12406 | Configuration Guide - Page 1
Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-11497-03 - Cisco 12406 | Configuration Guide - Page 2
is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco's installation instructions, it may cause interference with radio and television reception. This equipment has been - Cisco 12406 | Configuration Guide - Page 3
partner does not imply a partnership relationship between Cisco and any other company. (0812R) Any Internet Protocol (IP) addresses used in this document unintentional and coincidental. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide © 2009 Cisco Systems, Inc. All rights - Cisco 12406 | Configuration Guide - Page 4
- Cisco 12406 | Configuration Guide - Page 5
Request xx Definitions of Service Request Severity xxi Obtaining Additional Publications and Information xxii Product Overview 1-1 Introduction 1-1 Product Description 1-2 Physical and Functional Description 1-7 Chassis 1-7 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3 - Cisco 12406 | Configuration Guide - Page 6
1-19 System Status LEDs 1-21 Soft Reset Switch 1-22 PCMCIA Slots 1-23 Asynchronous Serial Ports 1-23 Ethernet Port 1-24 Performance Route Processor 1-25 PRP Memory Components 1-28 System Status LEDs 1-30 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 7
Module 1-47 Air Filters 1-49 Cable-Management System 1-50 Field-Replaceable Units 1-52 Technical Specifications 1-52 Preparing for Installation 2-1 Tools and Equipment 2-2 Safety and Compliance 2-2 General Safety Guidelines 2-3 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 8
Site Preparation Checklist 2-22 Installing the Router 3-1 Installing a Router 3-2 Installing the Rack-Mount Brackets (Optional) 3-3 Tools and Equipment Required 3-3 Installing the Optional Rack-Mount Brackets 3-3 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 9
IOS Software Images 3-37 Conditions to Check Before System Startup 3-38 Overview of the Boot Process 3-39 Starting the Router and Observing Initial Conditions 3-39 RP Alphanumeric LED 3-41 RP Interfaces Using the RP LEDs 3-42 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 7 - Cisco 12406 | Configuration Guide - Page 10
Interfaces 3-58 GRP Ethernet Interfaces 3-59 PRP Ethernet Interfaces 3-59 Line Card Interfaces 3-60 Checking the Software Version 3-61 show version Command 3-61 Verifying the Running Configuration Settings 3-62 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 8 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 11
Information and Support 3-82 Troubleshooting the Installation 4-1 Performing Other Configuration Tasks 4-1 Configuring the Software Configuration Register 4-1 Boot Field Settings 4-4 Configuration Register Settings 4-6 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 9 - Cisco 12406 | Configuration Guide - Page 12
for the Cisco 12000 Series Router 5-1 Diagnostics Overview 5-2 FPGA Overview 5-3 Using Diagnostics 5-6 Obtain and Place the Diagnostics Image 5-6 Upgrade the FPGA Image on a Line Card 5-7 Using the diag Command 5-8 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 10 OL - Cisco 12406 | Configuration Guide - Page 13
on Cisco 12006 and Cisco 12406 Enhanced Series Router 6-3 Cleaning or Replacing the Air Filters 6-7 Removing and Replacing the Blower Module 6-9 Troubleshooting the Blower Installation 6-12 Removing and Replacing AC and DC Power Subsystem Components 6-13 Installation Guidelines 6-14 Power Supply and - Cisco 12406 | Configuration Guide - Page 14
Alarm Card Cables 6-71 Transferring System Components 6-71 Transferring RP and Line Cards 6-72 Transferring the Clock and Scheduler, Switch Fabric, and Alarm Cards 6-72 Transferring the Power Modules 6-73 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 12 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 15
Router 6-77 Upgrading the RP and Line Card Memory 6-77 Technical Specifications A-1 Specifications A-1 Alarm Card Alarm Relay Connector Specifications A-6 Router Performance Upgrades and Model Identification A-6 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 16
Contents Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 14 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 17
Audience The Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide is written for hardware installers and system administrators of Cisco routers. This publication assumes that the user has a substantial background in installing and configuring router and switch-based hardware - Cisco 12406 | Configuration Guide - Page 18
12406 Routers. • Chapter 4, "Troubleshooting the Installation"-Explains how to identify and solve problems that might occur during installation. • Chapter 5, "Field Diagnostics for the Cisco 12000 Series Router"-Describes how to load and run the field diagnostics for the Cisco 12000 Series Internet - Cisco 12406 | Configuration Guide - Page 19
software configuration and reference documentation for additional information. • Commands and keywords are in boldface font. • Arguments for which you supply the beginning of a line indicate a comment line. Caution Means reader Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide xv - Cisco 12406 | Configuration Guide - Page 20
of hardware and software installation, configuration, and command guides for Cisco products and to Cisco website without being connected to the Internet. Certain products also have .pdf versions of the documentation available. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 21
1 800 553-NETS (6387). Documentation Feedback You can rate and provide feedback about Cisco technical documents by completing the online feedback form that appears with the technical documents on Cisco.com. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide xvii - Cisco 12406 | Configuration Guide - Page 22
are updated in real time, you can access a Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL: http://www.cisco.com/en/US/products/products_psirt_rss_feed.html xviii Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 23
provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support & Documentation website on Cisco.com features extensive online support resources. In addition, if you have a valid Cisco OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide xix - Cisco 12406 | Configuration Guide - Page 24
(S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide xx OL-11497 - Cisco 12406 | Configuration Guide - Page 25
service to satisfactory levels. Severity 4 (S4)-You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 26
make sound technology investment decisions. You can access iQ Magazine at this URL: http://www.cisco.com/go/iqmagazine or view the digital edition at this URL: http://ciscoiq.texterity.com/ciscoiq/sample/ xxii Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497 - Cisco 12406 | Configuration Guide - Page 27
at this URL: http://www.cisco.com/discuss/networking • World-class networking training is available from Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.html OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide xxiii - Cisco 12406 | Configuration Guide - Page 28
xxiv Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 29
series routers. The enhanced series of routers use higher capacity power supplies, a more powerful blower module, and have a new front door. Note Most illustrations are shown without the new front door for clarity. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 30
12000 series router family. These routers are aimed at scaling the Internet and enterprise backbones to speeds of 155 Mbps (OC-3/STM-1), 622 Mbps (OC-12/STM-4), 2.4 Gbps (OC-48/STM-16), and 10 Gbps (OC-192/STM). Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-2 OL-11497 - Cisco 12406 | Configuration Guide - Page 31
7-foot (2.15-m) equipment rack. Cisco 12006 and Cisco 12406 routers support system software downloads for most Cisco IOS software upgrades, which enables you to remotely download, store, and boot from a new Cisco IOS image. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-3 - Cisco 12406 | Configuration Guide - Page 32
-input power entry modules (PEMs). Note When operating your router on a single AC-input power supply or DC-input PEM, the second power module bay must have a blank filler (MAS-GSR-PWRBLANK=) installed to ensure EMI compliance. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 33
tests have been conducted in earthquake environment and criteria, office vibration and criteria, transportation vibration and criteria, and packaged equipment shock criteria. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-5 - Cisco 12406 | Configuration Guide - Page 34
Ethernet (FE) ports. • Current 1.275-inch pitch line cards will fit in the line card cage with the addition of a front panel adapter cover. The line card adapter cover is included with the 1.275-inch line card. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-6 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 35
-Management System, page 1-50 Chassis The Cisco 12006 and Cisco 12406 router chassis is an enclosure that consists of two integral card cages and two power module bays. (see Figure 1-1.) RP and Line Card Slots The RP and line card cage has six user-configurable slots that support one RP and up to - Cisco 12406 | Configuration Guide - Page 36
cards in the chassis as well as the blower module, and provides the physical communication pathway between cards, both for network data and system communication across the internal system maintenance bus (MBus). Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-8 OL-11497 - Cisco 12406 | Configuration Guide - Page 37
Chassis Power Because a Cisco 12006 or Cisco 12406 Router can be configured with either an AC-input power system or a DC-input power system, the power module bays will accept either AC-input power supply modules or DC-input PEMs. For more information about the power subsystems, see the "Power - Cisco 12406 | Configuration Guide - Page 38
right side of the chassis. Note To operate, Cisco 12006 and Cisco 12406 routers must have at least one CSC card installed, in addition to SFC and alarm cards. The CSC contains the following functionality: 1-10 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 39
) CSC slot or the second (unused) power supply bay. Note When operating your router with a single CSC, the second CSC slot must have a CSC blank filler (MAS-GSR6-CSCBLNK=) installed to ensure EMI compliance. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-11 - Cisco 12406 | Configuration Guide - Page 40
(LOS), it automatically activates the data paths of the redundant CSC, and data flows across the redundant path. The switch to the redundant CSC occurs within 0.5 second, with little or no loss of data. 1-12 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 41
alarms. Power-Up/Down Control Each MBus module directly controls the DC-DC converters installed devices. The responses provide component type, as well as slot numbers for the line cards, CSCs, SFCs, and alarm cards. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 42
converters. • The MBus module on the alarm card makes voltage adjustments for +5 VDC. • Environmental monitoring includes voltage monitoring, temperature monitoring, and sensing for the blower module fans. 1-14 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 43
as diagnostics, console support, and line card monitoring. Route Processor Functions The RP performs the following are primary functions: • Downloading the Cisco IOS software to all of the installed line cards at power-up • Providing a console (terminal) port for router configuration • Providing an - Cisco 12406 | Configuration Guide - Page 44
, extended data output (EDO) dynamic random-access memory (DRAM) on two 60-nanosecond (ns), dual in-line memory modules (DIMMs). 128 MB of DRAM is the minimum shipping configuration for the GRP. 57074 1-16 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 45
the Cisco IOS images in Flash memory enables you to download and boot from upgraded Cisco IOS images remotely or from software images resident in GRP Flash memory. The Cisco IOS software runs from within GRP DRAM. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 46
-45 MII GIGABIT ROUTE PROCESSOR PCMCIA slots slot 0: bottom slot 1: top Auxiliary port Console port Alphanumeric LED displays Ethernet interface (RJ-45 or MII) 1-18 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 47
applications, and runs the Cisco IOS software. The standard (default) GRP DRAM configuration is 64 MB of EDO DRAM, which you can upgrade to 256 MB. Table 1-2 lists the DRAM configurations and upgrades. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-19 - Cisco 12406 | Configuration Guide - Page 48
the network or from a local server and then add the new image to Flash memory or replace the existing files. You then can boot the routers either manually or automatically from any of the stored images. 1-20 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 49
LED displays (see Figure 1-7) are organized as two rows of four characters each. The content of the displays is controlled by the MBus module software. Both rows of the display are powered by the MBus module. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-21 - Cisco 12406 | Configuration Guide - Page 50
depends on the setting of the GRP software configuration register. (For more information on the software configuration register, see the "Configuring the Software Configuration Register" section on page 4-1.) 1-22 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 51
Industries Association/Telecommunications Industry Association (EIA/TIA)-232 receptacle (female) that provides a data circuit-terminating equipment (DCE) interface for connecting a console terminal. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-23 - Cisco 12406 | Configuration Guide - Page 52
terminal equipment (DTE) interface. The auxiliary port supports flow control and is often used to connect a modem, a channel service unit (CSU), or other optional equipment for Telnet or RJ-45 connection. 1-24 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 53
is not user configurable or field replaceable. • Memory-Additional memory components include onboard Flash memory and up to two Flash disks. • Sensors-Air-temperature sensors for environmental monitoring. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-25 - Cisco 12406 | Configuration Guide - Page 54
to remotely download, store, and boot from a new Cisco IOS software image. The Cisco IOS software runs from within the SDRAM of the PRP. Figure 1-9 shows the locations of the various hardware components on the PRP. 1-26 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 55
RX TX PRIMARY EN LINK AUX RX TX CONSOLE 6 78 RESET PERFORMANCE ROUTE PROCESSOR 1 (PRP-1) 9 10 75042 1 Backplane connector 2 Flash SIMM (Socket number P3) 3 SDRAM DIMMs port 9 Handle 10 Display LEDs OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-27 - Cisco 12406 | Configuration Guide - Page 56
I and Type II linear Flash memory cards are supported. See the "Flash Memory" section on page 1-29 for Flash disk information. Note If a single DIMM module is installed, it must be placed in bank 1 (U15). 1-28 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 57
as a TFTP server to allow other servers to boot remotely from stored images or to copy them into their own Flash memory. The onboard Flash memory (called bootflash) contains the Cisco IOS boot image, and OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-29 - Cisco 12406 | Configuration Guide - Page 58
is selected. Because both ports are supported on the PRP, the LED on port ETH0 generated during and after the boot process. The boot process and the content displayed are controlled by the MBus module software on the PRP. 1-30 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 59
of Cisco service personnel. Access to the soft reset switch is through a small opening in the PRP faceplate. To press the switch, you must insert a paper clip or similar small pointed object into the opening. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 60
the requirements of your configuration. Ethernet Ports The PRP has two 10/100 supports flow control. It is often used to connect a modem, a channel service unit (CSU), or other optional equipment for Telnet management. 1-32 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 61
line card while the router remains powered up. Note For detailed instructions on removing, replacing, and configuring the line cards, see the configuration note shipped with each line card when ordered as an FRU. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 62
10 Sample Line Cards Single Mode Multimode Ejector lever Chapter 1 Product Overview 0 ACRCAXTRPIRVKIETER 1 ACRCAXTRPIRVKIETER 2 RACCXATRPIRVKIETER 3 ACRCAXTRPIRVKIETER STM-1 MM POS Q OC-3/STM-1 SM IR POS 1-34 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 63
1 Product Overview Line Cards Alarm Cards Cisco 12006 and Cisco 12406 routers have two alarm card slots. Each alarm card performs the following function or indicates the following condition: • Alarm output • CSC status • SFC status • Alarm card status • Power source and power entry module status - Cisco 12406 | Configuration Guide - Page 64
. The green ENABLED LED indicates that the MBus module on the alarm card is operating properly. The yellow FAIL LED indicates that the alarm card has detected an error in itself or with the MBus power supply. 1-36 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 65
and Cisco 12406 routers can be powered by either an AC or DC power subsystem, as described in the following sections: • AC Power Subsystem, page 1-38 • DC Power Subsystem, page 1-42 • Power Distribution, page 1-47 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 66
local sales representative for assistance. AC PDU Facility AC power connects to AC-powered Cisco 12006 and Cisco 12406 routers though the AC PDU on the chassis rear panel. (See Figure 1-2 and Figure 1-12.) 1-38 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 67
power cords with different source AC power plugs are available. (See Figure 2-3 on page 2-15.) Note For true redundancy, connect each power supply to a separate power circuit protected by its own circuit breaker. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 68
switch 4 Release levers captive screws 5 LEDs -- Note When operating your router on a single power module, the second power module bay must have a blank filler (MAS-GSR-PWRBLANK=) installed to ensure EMI compliance. 1-40 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 69
long as AC power is connected to the router. • A handle is provided for ease in removing and replacing the power supply. • Captive screws on the power supply ejector levers secure it in the power supply bay. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-41 - Cisco 12406 | Configuration Guide - Page 70
of the power units fails. Contact your local sales representative for assistance. DC PDU Facility DC power connects to DC-powered routers though the connector blocks on the DC PDU. (See Figure 1-2 and Figure 1-14.) 1-42 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 71
connected through the DC PDU on the chassis rear panel. The DC PDU is equipped with two DC power connector blocks. Each DC power connector block is equipped with three terminal ports. Leads from the DC source OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-43 - Cisco 12406 | Configuration Guide - Page 72
power module bay must have a blank filler (MAS-GSR-PWRBLANK=) installed to ensure EMI compliance. Caution Cisco 12006 and Cisco 12406 routers are configured for either AC power or DC power. Do not mix AC-input power supplies and DC-input PEMs. 1-44 Cisco 12006 and Cisco 12406 Router Installation - Cisco 12406 | Configuration Guide - Page 73
: • A circuit breaker switch on the faceplate turns the PEM on and off. • A handle is provided for ease in removing and replacing the PEM. • Captive screws on the PEM ejector levers secure it in the PEM bay. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 1-45 - Cisco 12406 | Configuration Guide - Page 74
), Canadian Electrical Code, part I, CSA C22.1 (Canada), and IEC 364 (other countries). Note Cisco Systems recommends that you install an uninterruptable power source (UPS) as a safeguard against power loss. 1-46 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 75
verify the configuration may result in an unpredictable state if one of the power units fails. Contact your local sales representative for assistance. Blower Module Cisco 12006 and Cisco 12406 routers are equipped with a blower module to distribute air within the chassis. The blower module is - Cisco 12406 | Configuration Guide - Page 76
module Room air Room air 57649 Top view Air filter The two LEDs on the blower module provide a visual indication of blower module status. Both LEDs are visible on the blower module from the rear of the chassis. 1-48 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 77
air filters. (See Figure 1-18.) Figure 1-18 Air Filter Locations CISCO 12000 GIGABIT SWITCH SERIES ROUTER EJECT SSLLOOTT--01 RESET AUX CONSOLE COLL RX LINK TX RJ-45 MII GIGABIT ROUTE PROCESSOR 57678 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 78
air filters are contained in the "Cleaning or Replacing the Air Filters" section on page 6-7. Cable-Management System The Cisco 12006 and Cisco 12406 router cable as it enters the connector on the line card. 1-50 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 79
correct line card cable connectors. Chassis Cable-Management System CISCO 12000 GIGABIT SWITCH SERIES ROUTER EJECT SSLLOOTT--01 RESET AUX CONSOLE COLL RX LINK TX RJ-45 MII GIGABIT ROUTE PROCESSOR 101833 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 80
, AC-input power supplies - For DC-powered systems, DC-input PEMs • AC power cords (for AC powered systems) • Blower module • Air filters • Chassis cable-management bracket Technical Specifications For technical specifications and compliance information for Cisco 12006 and Cisco 12406 routers, see - Cisco 12406 | Configuration Guide - Page 81
site • Equipment you will need to install the router • Environmental conditions your installation site must meet to maintain normal operation Note Do not unpack the router until you are ready to install it. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-1 - Cisco 12406 | Configuration Guide - Page 82
does not include every potentially hazardous situation, so be alert. • General Safety Guidelines, page 2-3 • Compliance and Safety Information, page 2-5 • Laser Safety, page 2-5 • Lifting Guidelines, page 2-5 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-2 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 83
part 7. • Before installing, configuring, or maintaining the router, review the safety warnings listed in the Regulatory Compliance and Safety Information for the Cisco 12000 Series Router (Document Number 78-4347-xx) that accompanied your router. OL-11497-03 Cisco 12006 and Cisco 12406 Router - Cisco 12406 | Configuration Guide - Page 84
Safety and Compliance Chapter 2 Preparing for Installation • Cisco 12006 and Cisco 12406 Routers with an AC power distribution unit (PDU) and AC-input power supplies are shipped with AC power cords equipped with three-wire electrical grounding-type plugs that will fit into only a grounding-type - Cisco 12406 | Configuration Guide - Page 85
not have to move the router later to accommodate power source and/or network connections. Caution To prevent damage, never attempt to lift or tilt the router chassis using the handles on the blower module or line cards. These handles do not support the weight of the chassis. Whenever you lift any - Cisco 12406 | Configuration Guide - Page 86
for Installation • Have a second person help lift the equipment; avoid lifting the equipment alone. • Ensure that your footing is solid; balance the weight of can still cause damage to electronic components. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-6 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 87
Strap to the Cisco 12006 and Cisco 12406 Router Chassis CISCO 12000 GIGABIT SWITCH SERIES ROUTER EJECT SSLLOOTT--10 RESET AUX CONSOLE COLL RX LINK TX RJ-45 MII GIGABIT ROUTE PROCESSOR 57082 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-7 - Cisco 12406 | Configuration Guide - Page 88
the following guidelines when working with any equipment that is disconnected from a power source but still connected to telephone or network wiring: • Never install telephone wiring during a lightning storm. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-8 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 89
side of the chassis. Air circulates through the card cage and exhausts at the rear of the chassis. Observe the following guidelines when selecting a site in which to install Cisco 12006 and Cisco 12406 Routers: OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-9 - Cisco 12406 | Configuration Guide - Page 90
posts with mounting flanges on which to mount the router chassis. The distance between the center lines of the mounting holes on the two mounting posts must be 18.31 inches ± 0.06 inch (46.50 cm ± 0.15 cm). 2-10 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 91
the chassis for Cisco 12006 and Cisco 12406 Routers. Figure 2-2 Chassis Outer Dimensions and Footprint (shown with enhanced model front door) 17.234 in. 23.137 in. 30.877 in. 7.740 in. 18.950 in. 57090 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-11 - Cisco 12406 | Configuration Guide - Page 92
cable-management brackets included with the router to keep cables organized and out of the way of line cards, power modules, and blower modules. Consider the equipment and cabling that is already installed 2-12 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 93
the air away from the air intake vent. If necessary, operate the router with the rack door open or in an open rack. • The correct use of baffles inside an enclosed rack can assist in cooling the router. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-13 - Cisco 12406 | Configuration Guide - Page 94
AC-input power supply installed in the router. • Install an uninterruptable power source where possible. Power plug types used in North America, Australia, and Europe are described in Table 2-1 and shown in Figure 2-3. 2-14 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 95
13A replaceable fuse) Figure 2-3 AC Power Plugs 57648 North American plug L6-20 20A Australian plug AS 3112 15A European plug CEE 7/7 16A Italian plug CEI 23-16/VII 16A United Kingdom plug BS 1363 13A OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-15 - Cisco 12406 | Configuration Guide - Page 96
connection supplied via the International Electrotechnical Commission (IEC) 320 inlets for AC-powered units and the main terminal block ground connection for DC-powered units. • On Cisco 12006 and Cisco 12406 Routers configured for AC-input operation, the AC PDU is equipped with two three-wire - Cisco 12406 | Configuration Guide - Page 97
Chapter 2 Preparing for Installation Site Requirement Guidelines • On Cisco 12006 and Cisco 12406 Routers configured for DC-input operation, the DC PDU is equipped with two DC power connector blocks, each with wire-connection terminals for connecting the negative lead (top terminal), the positive - Cisco 12406 | Configuration Guide - Page 98
shown in Figure 2-5. The lug can be ordered from Cisco (Part Number 32-0607-01). Figure 2-5 Cable Lug 2.24 End View All measurements in inches 0.48 Ø 0.267 2 holes 0.25 0.63 0.37 0.08 Crimp area 25527 2-18 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 99
wire in the lug 2 Crimp the lug Note The three threaded inserts that make up the grounding receptacle are set in a triangle so that you can choose any two of the three holes to attach the lug and grounding cable. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 100
couple enough energy into unshielded conductors to destroy electronic devices. If you have had problems of this sort in the past, you may want to consult experts in electrical surge suppression and shielding. 2-20 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 101
you need to transport it. If you do not receive everything you ordered, contact a customer service representative for assistance. See the section titled, Obtaining Technical Assistance, page -Boilerplate 2. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-21 - Cisco 12406 | Configuration Guide - Page 102
- Software upgrades - Corrective or preventive maintenance procedures performed - Intermittent problems - Your comments Table 2-2 shows a sample site log. You can make copies of the sample or design your own site log. 2-22 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 103
Chapter 2 Preparing for Installation Site Preparation Checklist Table 2-2 Sample Site Log Date Description of Action Performed or Symptom Observed Initials OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 2-23 - Cisco 12406 | Configuration Guide - Page 104
Site Preparation Checklist Chapter 2 Preparing for Installation 2-24 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 105
Software Configuration for the Router, page 3-37 • Cisco IOS User Interface, page 3-50 • Configuration Changes, page 3-53 • Using Flash Memory Cards in the RP, page 3-66 • If You Need More Information, page 3-82 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 106
the router. • AC power source receptacles are easy to reach. Warning Do not mix power module input types in the router. All power modules installed in a router must be either AC-input power supplies or DC-input PEMs. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-2 OL - Cisco 12406 | Configuration Guide - Page 107
to bear the weight of the router while it is being positioned in the equipment rack and secured. The use of these mounting brackets is optional; you can install the router in the rack without all the screws. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-3 - Cisco 12406 | Configuration Guide - Page 108
Installing a Router Chapter 3 Installing the Router Figure 3-1 Installing the Optional Rack-Mount Brackets 1 1/4" 2 1/2" 3 3/8" 1/16" sheet metal 3/4" Left mounting rail Right mounting rail 57802 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-4 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 109
57772 OL-11497-03 The optional center-mount bracket installation kit ships in an accessories box included in the router shipping container. If any parts are missing, contact a Cisco service representative for assistance. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-5 - Cisco 12406 | Configuration Guide - Page 110
When installing the right side lower center-mount bracket, ensure that the bracket does not impede airflow through the air filter, which could cause overheating in the router. Step upper center-mount brackets. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-6 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 111
3-3 Chassis Mounting Bracket Holes Rack mounting bracket holes Line card Line card Line card Line card Line card Route processor CSC CSC Alarm Alarm SFC SFC SFC Power supply Power supply 57651 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-7 - Cisco 12406 | Configuration Guide - Page 112
. Caution Do not allow the chassis to hang free until you have installed a screw in all four hole groups (at least two screws on each side of the chassis). Step 5 Use a screwdriver to tighten all the screws. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-8 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 113
the Telcordia NEBS requirement for supplemental bonding and grounding connections. This receptacle consists of three threaded inserts located on the side of the chassis near the back panel. (See Figure 3-4.) OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-9 - Cisco 12406 | Configuration Guide - Page 114
onto a grounding wire of a wire size and length determined by your router location and facility environment. The crimping tool shown in Figure 3-6 is a standard crimping tool obtainable from many sources. 3-10 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 115
ESD-preventive strap to your wrist and connect the leash to the chassis or to another grounded, bare metal surface. Proceeding from left to right, identify the cables that attach to the first RP or line card. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-11 - Cisco 12406 | Configuration Guide - Page 116
that connects to each card port and connect the cable to the RP or line card port. Proceeding from left to right, carefully wrap the cables into the line card cable-management bracket using the velcro straps. 3-12 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 117
the vertical chassis cable-management bracket and turn the latch on the front of the bracket to secure the cables in the bracket. Connecting Alarm Card Cables Cisco 12006 and Cisco 12406 Routers have two alarm cards located in the two slots immediately above the left power supply bay and directly - Cisco 12406 | Configuration Guide - Page 118
these ports must be capable of asynchronous transmission. Asynchronous is the most common type of serial device; for example, most modems are asynchronous devices. 3-14 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 119
safety, connect all console, auxiliary, and Ethernet interfaces only to intrabuilding or nonexposed wiring or cabling. The intrabuilding cable must be shielded and the shield must be grounded at both ends. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-15 - Cisco 12406 | Configuration Guide - Page 120
DSU or other router) to the router. The auxiliary port is located next to the console port on the GRP card. The auxiliary port supports hardware flow control and modem control. An example the GRP= and GRP-B=. 3-16 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 121
flow control) Clear To Send (used for hardware flow control) Data Set Ready Signal Ground Output Input Output Carrier Detect (used for modem control) Data Terminal Ready (used for modem control only) Ring OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-17 - Cisco 12406 | Configuration Guide - Page 122
, and 2 stop bits. The console port requires a rollover RJ-45 cable. Figure 3-9 PRP Console and Auxiliary Port Connections SLSOLOT-T0-1 PRIMARY ETH 0 EN LINK 70692 RX TX PRIMARY asynchronous devices. 3-18 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 123
nonexposed wiring or cabling. The intrabuilding cable must be shielded and the shield must be grounded at both ends. PRP Console Port Signals The console port on the PRP is Receive Data Data Set Ready - OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-19 - Cisco 12406 | Configuration Guide - Page 124
on each RP can be used at the same time. The software configuration register is set to 0x0102, which causes the router to boot automatically from the Cisco IOS software image stored on the Flash memory card. 3-20 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 125
SSLLOOTT--01 RESET AUX 57080 Ensure that a console terminal is connected to the RP console port and turned on, or that you have a remote login to the router from another device through a Telnet session. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-21 - Cisco 12406 | Configuration Guide - Page 126
Connecting to the Console and Auxiliary Ports Chapter 3 Installing the Router Connecting the GRP to an Ethernet Network This section provides Mbps) or an IEEE 802.3u 100BASE-TX (100 Mbps) connection. 3-22 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 127
twisted-pair cable is recommended. Figure 3-12 shows the layout of the Ethernet MII receptacle on the GRP. Figure 3-12 Ethernet MII Receptacle Pin 1 H6538 OL- Clock Receive Data Code TxD Tx_CLK2 Tx_ER Tx_EN MDC RxD Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-23 - Cisco 12406 | Configuration Guide - Page 128
RJ-45 receptacle on the GRP. Figure 3-13 Ethernet RJ-45 Receptacle H2936 8 7 6 5 4 3 2 1 RJ-45 connector Table 3-6 Ethernet RJ-45 Receptacle Pin Configuration Pin Signal 1 TX+ 2 TX- 3 RX+ 3-24 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 129
labeled ETH0 and ETH1), attach the Category 5 UTP cable directly to a RJ-45 receptacle on the PRP. RJ-45 cables are not available from Cisco Systems, but are available from outside commercial cable vendors. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-25 - Cisco 12406 | Configuration Guide - Page 130
3-14 Using the Ethernet Port on the PRP Router A (Cisco 12000 series) EO Network 1.0.0.0 Host A POS EO Router B (Cisco 7500 series) Host B Network 2.0.0.0 Host A Router C (Cisco 7500 series) S6755 3-26 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 131
Ethernet Port Pin 1 2 3 4 5 Signal TxD+ TxD- RxD+ Termination Network Termination Network Description Transmit data + Transmit data - Receive data + No connection No connection OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-27 - Cisco 12406 | Configuration Guide - Page 132
lists the cabling specifications for 100-Mbps transmission over unshielded twisted-pair (UTP) cables. Note The transmission speed of the Ethernet ports is auto-sensing by default and is user configurable. 3-28 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 133
supply to accept AC power source voltage from an AC power source operating between 100 and 240 VAC, 20-Amp service in North America; and a range of from 185 to 264 VAC, 16-Amp service in an international environment. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration - Cisco 12406 | Configuration Guide - Page 134
the router: Table 3-10 Required Power Combinations Router Power AC power DC power Combination 1 AC-input power supply 1 power supply blank 2 AC-input power supplies 1 DC-input PEM 1 PEM blank 2 DC-input PEMs 3-30 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 135
AC power to the AC PDU on the router, see Figure 3-18 and follow these steps: Step 1 Attach an ESD-preventive strap to your wrist and connect the leash to the chassis or to another grounded, bare metal surface. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 136
the AC power source circuit breaker servicing each of the AC-input power supplies is switched on. Note When operating your router on a single power module, the second power module bay must have a blank filler (MAS-GSR-PWRBLANK=) installed to ensure EMI compliance. Connecting to a DC Power Source - Cisco 12406 | Configuration Guide - Page 137
to your wrist and connect the leash to the chassis or to another grounded, bare metal surface. Locate the DC PDU on the back of the router. The PDU is positioned directly below and behind the blower module. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-33 - Cisco 12406 | Configuration Guide - Page 138
and secure the lead. c. Repeat Step 3a and Step 3b for the remaining leads and for the second PDU connector block. Verify that the source DC circuit breaker servicing the DC PDU is switched on. 3-34 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 139
module. They should appear as described below: • Green LED labeled OK-Should be on • Red LED labeled FAIL-Should be off Listen for the blowers in the blower module; you should immediately hear them operating. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 140
FAIL • Three router alarm LEDs labeled CRITICAL, MAJOR, MINOR LEDs that normally should be on: • One MBUS status LED labeled ENABLED • Two CSC status LEDs labeled ENABLED • Three SFC status LEDs labeled ENABLED 3-36 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497 - Cisco 12406 | Configuration Guide - Page 141
power modules do not power up, or if the system or any interfaces do not initialize properly, see Chapter 4, "Troubleshooting the Installation." If you are still unable to resolve the problem, contact your Cisco service representative for assistance. IOS Software Configuration for the Router This - Cisco 12406 | Configuration Guide - Page 142
the Cisco IOS software image stored on the Flash memory card. New Flash memory cards must be formatted before use. To format a new Flash memory card, refer to the section "Formatting a Flash Memory Card, page 3-67". 3-38 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 143
filled with card blanks. This ensures proper air flow through the chassis and electromagnetic compatibility (EMC). • All cards are fully inserted in their cages and bays. • All captive screws are tightened. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-39 - Cisco 12406 | Configuration Guide - Page 144
, the blower might be difficult to hear. In that case, place your hand near the exhaust vents at the top and bottom rear of the chassis to verify that the blower is operating. 3-40 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 145
digits) 57079 OL-11497-03 Each four-digit display shows part of a two-line system message. During the RP boot process, the LED displays Cisco IOS software commands at the ROM monitor prompt (rommon>). RP ROM monitor Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-41 - Cisco 12406 | Configuration Guide - Page 146
available for Cisco 12006 and Cisco 12406 Routers: the Gigabit Route Processor (GRP) and the Performance Route Processor (PRP). Each of these route processor types is reviewed in the a successful RP boot. 3-42 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 147
a valid Cisco IOS software image is inserted in PCMCIA slot 0 and the software configuration register is set to 0x0102 (the factory default setting), the router automatically boots using this image. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-43 - Cisco 12406 | Configuration Guide - Page 148
. These two LEDs, when on, identify which of the two Ethernet connections is selected. Because both ports are supported on the PRP, the LED on port ETH0 is always on. The ETH1 LED goes on when it is selected. 3-44 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 149
) Copyright (c) 1986-2002 by cisco Systems, Inc. Compiled Sat 20-Aug-01 18:34 . . . Note The system banner that you see depends on the image version of the Cisco IOS software that the system is running. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-45 - Cisco 12406 | Configuration Guide - Page 150
of the interfaces against the LED descriptions in the configuration notes for each line card. If the system does not complete each of the boot process steps, see Chapter 4, "Troubleshooting the Installation." 3-46 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 151
valid system image. Locating a Valid Cisco IOS Software Image To locate a Cisco IOS software image for manually booting the router from the ROM monitor prompt (rommon>), File name gsr-p-mz.120-7.4.5 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-47 - Cisco 12406 | Configuration Guide - Page 152
the factory default setting of 0x0102 in the software configuration register causes the system to boot Cisco IOS software from a Flash memory card inserted in PCMCIA slot 0 the next time you boot the router. 3-48 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 153
any time to alter previously entered configuration information. The advantage in using the setup command utility is that the system uses an interactive script to guide you through the configuration process. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-49 - Cisco 12406 | Configuration Guide - Page 154
are stored and can be used when you reboot your router. Starting at global configuration mode, you can enter interface configuration mode, subinterface configuration mode, and other protocol-specific modes. 3-50 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 155
EXEC mode to privileged EXEC mode on the router named Router. Router> enable password: Router# For information about using passwords, see the "Configuring Global Parameters" section on page 3-57. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-51 - Cisco 12406 | Configuration Guide - Page 156
configure subinterfaces, see the appropriate module for a specific protocol in the Cisco IOS software documentation. ROM Monitor Mode If your router then pressing the Break key during the first 60 seconds of startup. 3-52 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL- - Cisco 12406 | Configuration Guide - Page 157
a setup session automatically invoked during the first-time startup of the router. During first-time startup, the system displays the system banner information, then starts the System Configuration Dialog. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-53 - Cisco 12406 | Configuration Guide - Page 158
. Enter enable password: bravo The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: charlie Configure SNMP Network Management? [no]: 3-54 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 159
mask is /24 The following configuration command script was created: hostname Router enable secret 5 $1$krIg$emfYm/1OwHVspDuS8Gy0K1 enable password wilma line vty 0 4 password charlie no ip address . . . OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-55 - Cisco 12406 | Configuration Guide - Page 160
that the POS interface has been configured previously and you are being queried by the system for changes, you will see a display in the following form: Configuring interface POS1/0: Is this interface in use?[yes]: Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 161
(RFC) 1035, Domain Names-Implementation and Specifications. Upper- and lowercase characters look the same to many Internet software configure privilege levels, refer to the "Configuring Passwords and Privileges" OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 162
in the Security Configuration Guide. This document is part of the Cisco IOS software configuration documentation set that corresponds to the Cisco IOS software release installed on your Cisco hardware. The enable secret password functionality is available for Cisco 12006 and Cisco 12406 Routers. You - Cisco 12406 | Configuration Guide - Page 163
. Cisco Express Forwarding (CEF) functions are switched off by default for security reasons. Cisco strongly cautions you to consider the security implications of switching on CEF routing functions on these ports. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 164
Changes Chapter 3 Installing the Router Line Card Interfaces Because of the wide variety of line cards supported by Cisco 12006 and Cisco 12406 Routers, you should see the configuration note that shipped with a particular card for interface configuration information. This section provides - Cisco 12406 | Configuration Guide - Page 165
) Copyright (c) 1986-2002 by cisco Systems, Inc. Compiled Sat 20-Aug-01 18:34 Image text-base: 0x60010950, data-base: 0x61C00000 ROM: System Bootstrap, Version 11.2(17)GS2, [name 180] EARLY DEPLOYMENT RELEA) OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-61 - Cisco 12406 | Configuration Guide - Page 166
-config command might be different. show running Config Command Example router# show running-config Building configuration... Current configuration: ! version 12.0 no service pad no service udp-small-servers 3-62 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 167
can access Cisco IOS software documentation and hardware installation and maintenance documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-63 - Cisco 12406 | Configuration Guide - Page 168
! version 12.0 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname Router ! enable secret 5 $1$/5HX$OOvyhG2JYhNaCbPa45Wmn/ enable password wilma 3-64 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497 - Cisco 12406 | Configuration Guide - Page 169
Chapter 3 Installing the Router Configuration Changes OL-11497-03 ip cef distributed switch ip host biff -vc 11 no logging trap ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 password bambam login ! end Router# Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-65 - Cisco 12406 | Configuration Guide - Page 170
Memory, page 3-72 • Copying Files, page 3-72 • Copying a Cisco IOS Software Image, page 3-74 • Copying Cisco IOS Software Updates, page 3-75 • Copying Files Between RP Memory and a Flash out toward you. 3-66 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 171
pop out unless the card is inserted correctly. Part of the card remains outside the slot even when with your router contains the default Cisco IOS software image you need to boot your router. Warning router. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-67 - Cisco 12406 | Configuration Guide - Page 172
: Router# configure terminal Router(config)# no boot system Router(config)# boot system flash slot0:new.image Router(config)# config-register 0x2102 Ctrl-Z Router# copy running-config startup-config Router# reload 3-68 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 173
The system looks in the Flash memory SIMM on the RP for a default Cisco IOS software image. • 0x0102-The system disables the Break function and checks for a cd command include: Router# cd slot1: Router# pwd OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-69 - Cisco 12406 | Configuration Guide - Page 174
myfile1 Sep 30 2002 15:17:33 gsr-diag-mz.RELEASE28 Sep 30 2002 15:22:49 gsr-p-mz.p7 20578304 bytes total (9661756 bytes free) Router# Files that are deleted from the deleted file later using the undelete command. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 175
sudden power loss, the squeezed data is temporarily saved to another Flash memory area reserved specifically for system use. An example of the squeeze command follows. Router# in the event of a power failure. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-71 - Cisco 12406 | Configuration Guide - Page 176
avoid losing valid Cisco IOS images, upgrade your Cisco IOS software images in Flash memory one at a time. Upgrade your PCMCIA-based Flash memory separately from the onboard Flash SIMM (bootflash) on the RP. 3-72 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 177
output generated by a copy tftp:filename command: Router# copy tftp:myfile1 slot0:myfile1 20575008 bytes available on device slot0, proceed? [confirm] Address or name of remote designated destination device. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-73 - Cisco 12406 | Configuration Guide - Page 178
instructions on using this facility, see the "Configuration Changes" section on page 3-53 or refer to the Configuration Fundamentals Configuration Guide for the IOS software release running on this router . 3-74 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 179
Step 5 in the following procedure and enter the command boot system flash slot0:image.new to designate the file image.new as the new default Cisco IOS software boot image. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-75 - Cisco 12406 | Configuration Guide - Page 180
system Router(config)# boot system flash slot0:image.new Ctrl-Z Router# copy running-config startup-config Router# reload When the system reloads, the file image.new is booted from the Flash memory card in slot 0. 3-76 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 181
: | slot1:] is one of the Flash memory card slots, and filename is the name of the configuration file to be copied. Note that the environmental variable CONFIG_FILE must point to NVRAM (the system default). OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-77 - Cisco 12406 | Configuration Guide - Page 182
Using Flash Memory Cards in the RP Chapter 3 Installing the Router To copy a configuration file named myfile2 from the NVRAM on the RP to a Flash memory memory card slot number) and the name of the new file. 3-78 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 183
2002 19:24:12 gsr-p-mz.112-8 3 1215 May 10 2002 20:30:52 myfile1 4 6176844 May 10 2002 23:04:10 gsr-p-mz.112-8.1 5 1186 May 10 2002 16:56:50 myfile2 9197156 bytes available (11381148 bytes used) Router# OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-79 - Cisco 12406 | Configuration Guide - Page 184
EXEC mode prompt: Router# dir slot0: -#- -length- -----date/time------ name 1 5200084 May 10 2002 19:24:12 gsr-p-mz.112-8 3 1215 May 10 2002 20:30:52 myfile1 4 6176844 May 10 2002 23:04:10 gsr-p-mz.112-8.1 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 185
startup configuration file, now stored in NVRAM, becomes the default running configuration file: Router# copy startup-config running-config Router# %SYS-5-CONFIG_I: Configured from memory by console Router# OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-81 - Cisco 12406 | Configuration Guide - Page 186
reading Cisco documentation on the World Wide Web, you can submit comments electronically. Click Feedback on the toolbar, and then select Documentation. After you complete the form, click Submit to send it to Cisco. 3-82 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 187
accompanied your GRP. For additional PRP information, refer to the configuration note Performance Route Processor (PRP) Installation and Configuration (Document Number 78-13302-xx) that accompanied your PRP. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 3-83 - Cisco 12406 | Configuration Guide - Page 188
If You Need More Information Chapter 3 Installing the Router 3-84 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 189
chapter provides troubleshooting guidelines for Cisco 12006 and Cisco 12406 Routers. If the solutions provided in this chapter do not make the router fully functional, contact your Cisco service representative for assistance. • Performing Other Configuration Tasks, page 4-1 • Problem Solving with - Cisco 12406 | Configuration Guide - Page 190
00 to 03 0x0000 to 0x000F Comprises the boot field for defining the source of a default Cisco IOS software image required to run the router 06 0x0040 Causes system software to ignore the contents of NVRAM Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-2 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 191
at the ROM monitor prompt (rommon>) awaiting a user command to boot the system manually. On power up, the system automatically boots the first system image found in the onboard Flash memory SIMM on the RP. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-3 - Cisco 12406 | Configuration Guide - Page 192
If you enter the boot command without an argument (that is, without specifying a file or any other boot instructions), the system automatically boots using the default image in the Flash memory SIMM on the RP. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-4 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 193
a range of filenames such as the following: cisco2-grp . . . cisco17-grp or cisco2-prp . . . cisco17-prp The system would use one of the filenames in this range to boot a default system image stored on a network TFTP server. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-5 - Cisco 12406 | Configuration Guide - Page 194
4-1 on page 4-2 for the possible settings to enter as the four-bit value parameter. Exit global configuration mode by entering Ctrl-Z. Router(config)# config-register 0xvalue Router(config)# Ctrl-Z Router# Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-6 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 195
"Problem Solving with Subsystems" section on page 4-14. Note Configuration register changes take effect only after the system reloads, such as when you enter a reload command from the console. Step 7 Reboot the router. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration - Cisco 12406 | Configuration Guide - Page 196
default filenames for booting over the network. However, a valid boot system configuration command stored in the NVRAM configuration file overrides any computed default filename for booting over the network. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-8 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 197
cisco14-prp 1 1 0 0 cisco15-grp or cisco15-prp 1 1 0 1 cisco16-grp or cisco16-prp 1 1 1 0 cisco17-grp or cisco17-prp 1 1 1 1 The significance of bits 8 through 14 in the software configuration register follows. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 198
Other Configuration Tasks Chapter 4 Troubleshooting the Installation Bit 8-Bit 8 of the software configuration register controls the 12 0 0 1 1 Bit 11 0 1 0 1 Data Transmission Rate (bps) 9600 4800 1200 2400 4-10 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 199
power supplies, wait 5 seconds, then restore power. If the Break function is enabled, press the Break key or send a break by holding down the Control key and pressing the right square bracket key (Ctrl-]). OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-11 - Cisco 12406 | Configuration Guide - Page 200
the router by entering the initialize command at the ROM monitor prompt: rommon 1> initialize The router goes through a power cycle. The software configuration register is set to ignore the configuration file. 4-12 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 201
the config-register 0xvalue command: router(config)# config-register 0xvalue router(config)# Value is a hexadecimal number preceded by 0x, as in the following example: router(config)# config-register 0x0102 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-13 - Cisco 12406 | Configuration Guide - Page 202
or DC-input power distribution unit (PDU) - AC-input power supplies or DC-input power entry modules (PEMs). Cisco 12006 and Cisco 12406 Routers can be configured for source AC or source DC power. (You can not mix and match AC and DC power.) - Chassis backplane power distribution. The -48 VDC power - Cisco 12406 | Configuration Guide - Page 203
clock, immediately powers up. • The MBus module on the RP monitors the progress of the CSC power up. When the CSC has powered up, the MBus module on the RP turns on its DC-DC converter, powering up the RP. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-15 - Cisco 12406 | Configuration Guide - Page 204
period. This test allows you to verify that there are no failed LEDs. The following sections describe what you should expect to see in the power module LEDs on router startup. 4-16 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 205
of the LEDs on the power supply faceplate. Figure 4-1 AC-Input Power Supply LEDs 3 25 4 1 AC-input power supply 2 Handle 3 Power standby switch 57916 1 4 Captive screws on release levers 5 LEDs -- OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-17 - Cisco 12406 | Configuration Guide - Page 206
is within specified limits. Power source is not within specified limits. Power supply is operating normally in a power-on condition. Power supply is operating in a fault condition and shutdown has occurred. 4-18 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 207
Color Green Green Amber Function PEM is operating normally in a powered-on condition. DC power is present at the PEM input and within the specified limits. Indicates input is wired backward at the PDU input. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 208
blower module. Figure 4-3 Blower Module Location and Features 1 3 4 HIGH SPEED BLOWER 101114 2 1 Blower module 2 Blower module LEDs 3 Blower module handle 5 4 Air exhaust vents 5 Power distribution unit (PDU) 4-20 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 209
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems When the system is operating FAIL • Three SFC status LEDs labeled FAIL • Three router alarm LEDs labeled CRITICAL, MAJOR, MINOR OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-21 - Cisco 12406 | Configuration Guide - Page 210
-Indicates which RP software component is running. • Bottom display-Indicates the current phase of the boot process. Status messages are displayed as the boot process continues. (See Table 4-8 on page 4-30.) 4-22 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 211
the power module DC output power and internal DC voltages. This LED stays on when all the following conditions are met: - The power supply is fully seated in its bay. - The power supply power standby switch is on. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 212
to a separate AC power source. d. If the router is connected to an uninterruptable power supply (UPS), verify that the UPS is functioning correctly. Note that there might be a UPS for each power supply in the system. 4-24 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 213
power supply DC LED. If the blower module is operating, all internal DC voltages are within tolerance. Use the show environment command to check the voltages on each card. The blower module uses -48 VDC. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-25 - Cisco 12406 | Configuration Guide - Page 214
for replacement. If you are unable to resolve the problem or if you determine that either the power supply or power cable is faulty, contact a service representative for assistance. Troubleshooting the DC-Input Power Entry Module Begin checking the DC-input PEM by first looking at the LEDs on the - Cisco 12406 | Configuration Guide - Page 215
, go to Step 6. • If the DC power source wiring appears to be okay, but the power supply INPUT OK LED remains off when you switch on the PEM, go to Step 5. Remove the PEM and insert it in the second bay in the router, or into a bay on another Cisco 12006 or Cisco 12406 Router. • If the INPUT OK LED - Cisco 12406 | Configuration Guide - Page 216
are unable to resolve the problem or if you determine that either the PEM or power wiring is faulty, contact a service representative for assistance. Troubleshooting the Processor Subsystem The Cisco 12006 and Cisco 12406 Router processor subsystem consists of the RP, the line cards, and the alarm - Cisco 12406 | Configuration Guide - Page 217
to reseat or replace the RP. Caution The RP reset switch resets the RP and the entire system. To prevent system errors and problems, use it only at the direction of a Cisco-certified service representative. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-29 - Cisco 12406 | Configuration Guide - Page 218
Problem Solving with Subsystems Chapter 4 Troubleshooting the Installation CPU data and instruction cache CACH PARY specific sequence. 2. Some messages appear for a fraction of a second; others last several seconds. 4-30 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 219
running POST memory test has finished running Initialize main memory for ROM Save reset reason register Reset the I/O system on the card OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 4-31 - Cisco 12406 | Configuration Guide - Page 220
DRAM UP IOS RUN The line card is enabled and ready for use 1. The messages shown do not indicate a specific sequence. 2. Some messages appear only for a fraction of a second; others last several seconds. 4-32 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 221
Problem Solving with Subsystems Troubleshooting by Using the Alarm Cards The alarm cards are installed in the alarm card slots immediately beneath the clock and scheduler card slots. The alarm card has four primary functions: • Redundant generation of the DC MBus supply voltage for the line - Cisco 12406 | Configuration Guide - Page 222
and energizes the appropriate alarm display relays, activating any external audible or visual alarms wired to the alarm display. The RP also logs a message about the threshold violation on the system console. 4-34 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 223
the Installation Problem Solving with Subsystems Troubleshooting the Cooling Subsystem Cisco 12006 and Cisco 12406 Routers have a blower module located on the rear of the chassis, which provides cooling air for the router components. (See Figure 4-3.) The blower module receives power and - Cisco 12406 | Configuration Guide - Page 224
temperatures measured at each card. If the blower module is faulty, you must replace the entire blower module. If you are still unable to resolve the problem, contact a service representative for assistance. 4-36 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 225
being tested out of service. If the tested card passes the diagnostic tests, it is returned to normal operation. If there is a hardware fault, the card remains out of service after the testing is completed. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-1 - Cisco 12406 | Configuration Guide - Page 226
or 12.0(21)ST or later, the default download method changes from the MBus to the switch fabric. It takes about 1 minute to obtain test results from the switch fabric, compared to 15 minutes to obtain test results from the MBus. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 227
in Flash memory on the line card. When the FPGA code resides on Flash memory and the Cisco IOS code checks the revision, you may be informed by the Cisco IOS boot process that an FPGA upgrade is necessary. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-3 - Cisco 12406 | Configuration Guide - Page 228
12: %SYS-5-RESTART: System restarted -Cisco Internetwork Operating System Software IOS (tm) GS Software (GLC1-LC-M), Experimental Version 12 on a line card in slot 0. router# diag Router# Launching a Field Diagnostic for slot 0 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 229
Cisco 12000 Series Router FPGA Overview Loading muckier/award/c12k-fdiagsbflc-mz.conn_isp from 223.255.254.254 (via Ethernet0): !!!!!( stuff deleted) OK - 8452824 bytes] FD 0 FD 0> GSR **** for slot 0 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-5 - Cisco 12406 | Configuration Guide - Page 230
is named c12k-fdiagsbflc-mz.120-25.S and is always available on Cisco.com. 120-25.S is the version number of the image that corresponds to the Cisco IOS image, in this example, Cisco IOS Release 12.0(25)S. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-6 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 231
c12k-fdiagsbflc-mz.120-25.S, where 120-25.S is the Cisco IOS Release number. • For Flash memory cards, the source path would typically be slot0:c12k-fdiagsbflc-mz.120-25.S or slot1:c12k-fdiagsbflc-mz.120-25.S. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-7 - Cisco 12406 | Configuration Guide - Page 232
] [device] [messaging] diag slot-number previous diag slot-number halt diag slot-number update-fpga source {tftp | flash} source-path [dl-timeout-plus ] Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-8 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 233
-number source Description Slot number of the card you want to test. Specifies that the source path of the line card diagnostic image follows. This keyword must be followed by either the tftp or flash keyword. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-9 - Cisco 12406 | Configuration Guide - Page 234
the verbose option will result in up to a 15-minute delay before any results are displayed. Cisco recommends that the verbose option be specified and results captured when communicating with Cisco TAC. 5-10 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 235
. 300 seconds is the baseline value. Any value from 1 to 2000 adds that value to 300. For example, a dl-timeout-plus value of 12 makes the total value 312 seconds. Supports users with slow TFTP boot paths. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-11 - Cisco 12406 | Configuration Guide - Page 236
nonselective in cases where a line card contains multiple FPGAs. Note DO NOT unplug the line card or terminate the field diagnostics session during this test. Provides additional troubleshooting information. 5-12 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 237
under the guidance of a TAC engineer and only when observing tightly controlled static-sensitive device handling procedures. Do NOT replace memory components without proper body grounding and board grounding. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-13 - Cisco 12406 | Configuration Guide - Page 238
1) FD 7> Skipping MBUS_FDIAG command from slot 2 FD 7> Just into idle state Field Diagnostic ****PASSED**** for slot 7 Shutting down diags in slot 7 Board will reload 5-14 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 239
) TESTSDISP FATL FD 7> Test list selection received: Test ID 1, Device 0 FD 7> running in slot 7 (30 tests from test list ID 1) FD 7> Just into idle state Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-15 - Cisco 12406 | Configuration Guide - Page 240
TBM SSRAM Datapins Memory FDIAG_STAT_IN_PROGRESS(7): test #12 PSA TLU SDRAM Marching Pattern FDIAG_STAT_IN_PROGRESS(7): replaced and returned to Cisco for repair: Field Diag download COMPLETE for slot 7 FD 3 5-16 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 241
previous test results of a line card. Diagnostics had been run 64 times on this line card. Because the board Router # diag 7 prev Field Diag eeprom values: run 64 fail mode 0 (PASS) slot 7 last test failed was 0, error code 0 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 242
Cisco 12000 Series Router The following example shows the output of a line card test with the update-fpga option specified. Router# diag 7 verbose source tftp tftp://223.255.254.254/c12k-fdiagsbflc-mz.120 FD 3> GSR Field Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 243
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Command COMPLETED Field Diags: pid 121, status 6, 0, error code 0 Shutting down diags in slot 7 Board will reload Router# OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 5-19 - Cisco 12406 | Configuration Guide - Page 244
Using the diag Command Chapter 5 Field Diagnostics for the Cisco 12000 Series Router 5-20 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 245
and Installing the Front Door on Cisco 12006 and Cisco 12406 Enhanced Series Router, page 6-3 • Cleaning or Replacing the Air Filters, page 6-7 • Cleaning or Replacing the Air Filters, page 6-7 • Removing and Replacing the Blower Module, page 6-9 • Removing and Replacing AC and DC Power Subsystem - Cisco 12406 | Configuration Guide - Page 246
disconnected from source power: a. AC-powered systems-Unplug both AC power cords from the power outlets. b. DC-powered systems-Disconnect and remove the source DC wires from both power connector blocks on the PDU. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-2 OL-11497 - Cisco 12406 | Configuration Guide - Page 247
on the power modules are off, and power module fans are off. b. LEDs on the RP, line cards, and alarm cards are off. c. LEDs on the blower module are off, and all blower module fans are off. Removing and Installing the Front Door on Cisco 12006 and Cisco 12406 Enhanced Series Router The Cisco 12006 - Cisco 12406 | Configuration Guide - Page 248
6-1). Figure 6-1 Opening the Front Door 149543 1 CISCO 12000 GIGABIT SWITCH SERIES ROUTER EJECT SSLLOOTT--01 RESET AUX CONSOLE COLL RX LINK TX RJ-45 MII GIGABIT ROUTE PROCESSOR 1 Front Door Latch Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-4 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 249
the chassis hinge brackets. Figure 6-2 Removing or Installing Hinge Pins 149544 CISCO 12000 GIGABIT SWITCH SERIES ROUTER EJECT SSLLOOTT--10 RESET AUX CONSOLE COLL RX LINK TX RJ-45 MII GIGABIT ROUTE PROCESSOR OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration - Cisco 12406 | Configuration Guide - Page 250
pivot blocks to the left side and tighten the screws until snug. b. Mount the bumpers to the right side and tighten the screws until snug. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-6 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 251
Cisco 12406 routers are equipped with two user-serviceable air filters that remove dust drawn into the router by the blower module. One time per month (or more often in dusty environments), examine the air filters. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 252
Removing the Air Filters 2 1 CISCO 12000 GIGABIT SWITCH SERIES ROUTER EJECT SSLLOOTT--01 RESET AUX CONSOLE COLL RX LINK TX RJ-45 MII GIGABIT ROUTE PROCESSOR 129403 1 Air filter door 2 Air filters Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-8 OL-11497 - Cisco 12406 | Configuration Guide - Page 253
by nearly 40 percent to provide additional cooling to the chassis. The new fans operate at a higher speed to provide improved airflow, so you may notice increased sound generated from the new blower module. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-9 - Cisco 12406 | Configuration Guide - Page 254
blower module by grasping it on each side and pulling it straight back from the chassis. Figure 6-5 Removing the Blower Module 1 2 129401 HIGH SPEED BLOWER 1 Carrying handle 2 Captive screws (2 on each side) 6-10 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 255
the chassis. The (green) OK indicator should light. If the OK indicator does not light, see the "Troubleshooting the Blower Installation" section on page 6-12. d. Lower the blower module handle to its operating position. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration - Cisco 12406 | Configuration Guide - Page 256
all power cords are connected properly. Loosen the four captive screws and reseat the blower module to the chassis. Retighten the captive screws to ensure the blower module is properly seated to the backplane connector. 6-12 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 257
blower module also fails, power off the router and contact a Cisco service representative for assistance. Removing and Replacing AC and DC Power Subsystem Components This section contains removal and replacement procedures for the AC and DC power systems used with the Cisco 12006 and Cisco 12406 - Cisco 12406 | Configuration Guide - Page 258
Removal and replacement procedures are the same for either type of power supply, but because of their power capacity and physical differences, you cannot mix different types of power supplies in the chassis. 6-14 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 259
not a requirement and used a blank filler (MAS-GSR-PWRBLANK=) in place of a second power supply to ensure EMI compliance. Newer 1900 W power supplies require redundancy. You must install two power supplies. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-15 - Cisco 12406 | Configuration Guide - Page 260
in place of a second power supply to ensure EMI compliance. New 1900 W power supplies require redundancy...you must install two power supplies. DC PDU (12000/6-DC-PDU=) Required for 1900 W power supplies. 6-16 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 261
blower upgrade (not included in the power upgrade kit) is also required to meet NEBS extended temperature range requirements. To order the blower upgrade (12000/6-BLOWER=), contact your Cisco representative. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-17 - Cisco 12406 | Configuration Guide - Page 262
the components of an AC power supply. Figure 6-7 AC Power Supply Components 3 1 57916 25 4 1 AC PEM 2 Handle 3 Power On/Off switch 4 Captive screws/release levers 5 AC input/DC output status indicators 6-18 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 263
stops while upgrades take place. Step 1 Step 2 Step 3 Set the power switch to the Off (0) position. Unplug the power supply cord from its AC outlet. Power off the circuit breaker assigned to that AC outlet. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-19 - Cisco 12406 | Configuration Guide - Page 264
of its bay while supporting it with your other hand. Warning The power supply weighs approximately 14 lb (6.35 kg). Use two hands to remove the power supply. Figure 6-8 Releasing the AC Power Supply 84372 6-20 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 265
the power supply into the chassis. b. Close the ejector levers and tighten the captive screws to securely seat the power supply to the backplane connector. Figure 6-9 Seating the AC Power Supply 84373 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-21 - Cisco 12406 | Configuration Guide - Page 266
AC power outlet. - Each AC power supply operating in the nominal range of 200 to 240 VAC requires a minimum service of 20A, North America (or 16A, international). • Make sure the source AC circuit breaker is switched on. 6-22 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 267
switch is set to the On (1) position. If the indicator is off, toggle the power switch off and then on. If the indicator remains off after several attempts to power it on, replace the power supply with a spare. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 268
1 AC Power Distribution Unit 4 3 5 6 57650 2 1 Captive screw 2 AC power cord connector/retention clip (A) 3 AC power cord connector/retention clip (B) 4 AC power distribution unit 5 Guide pin 6 Blower module connector 6-24 Cisco 12006 and Cisco 12406 Router Installation and Configuration - Cisco 12406 | Configuration Guide - Page 269
lever and pivot the levers open to unseat the power supply from its PDU connector (Figure 6-11). • It is not necessary to remove the power supply from its bay. • Repeat this step for the second power supply. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-25 - Cisco 12406 | Configuration Guide - Page 270
Removing and Replacing an AC PDU Chapter 6 Maintaining the Router Figure 6-11 Unseating the AC Power Supply 84372 6-26 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 271
captive screws on the blower module. c. Remove the blower module by grasping it on each side and pulling it straight back from the chassis. Figure 6-12 Removing the Blower Module 101115 HIGH SPEED BLOWER OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-27 - Cisco 12406 | Configuration Guide - Page 272
the PDU at a slight angle makes it easier to remove it from the chassis. Figure 6-13 Removing the AC PDU 57676 Step 8 Install the new PDU and tighten its (4) captive screws to secure it to the chassis. 6-28 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 273
Step 10 Step 11 Step 12 Reconnect the power cords to the PDU and secure them using their retention clips. Plug the power cords into their AC outlets. Power on the circuit breakers assigned to the AC outlets. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-29 - Cisco 12406 | Configuration Guide - Page 274
the power supply to the chassis. c. Repeat steps a. and b. for the second power supply. Figure 6-15 Seating the AC Power Supply 84373 Step 14 Set the power switch on both power supplies to the On (1) position. 6-30 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 275
OK INPUT OK MISWIRE 62203 5 4 OUTPUT OK INPUT OK MISWIRE 243 1 DC PEM 2 Handle 3 Power On/Off switch 1 4 Captive screws/release levers 5 Cooling fan 6 AC input/DC output/miswire status indicators OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-31 - Cisco 12406 | Configuration Guide - Page 276
. Step 2 Power off the circuit breaker assigned to the power supply. Warning To ensure that power remains off while you are performing this procedure, tape the circuit breaker switch in the Off (0) position. 6-32 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 277
with your other hand. Warning The power supply weighs approximately 10 lb (4.5 kg). Use two hands to remove the power supply. Figure 6-17 Releasing the DC Power Supply OUTPUT OK INPUT OK MISWIRE 101116 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-33 - Cisco 12406 | Configuration Guide - Page 278
chassis. b. Close the ejector levers and tighten the captive screws to securely seat the power supply to the backplane connector (Figure 6-18). Figure 6-18 Seating the DC Power Supply OUTPUT OK INPUT OK MISWIRE 101117 6-34 Cisco 12006 and Cisco 12406 Router Installation and Configuration - Cisco 12406 | Configuration Guide - Page 279
properly: • Power leads are securely connected to the power connector block on the PDU. • Power cables are securely connected at the DC source connection. • The source DC circuit breaker is turned on. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-35 - Cisco 12406 | Configuration Guide - Page 280
spare power supply does not work, replace the PDU. • Miswire (amber)-Indicates the input wiring is incorrect at the PDU power connection block. Correct wiring to the DC power connector block (see Figure 6-25). 6-36 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497 - Cisco 12406 | Configuration Guide - Page 281
Unit POWER B 4 + GND 3 5 6 POWER A + GND 2 1 Captive screw 2 DC power connector block (A) 3 DC power connector block (B) 4 DC power distribution unit 5 Guide pin 6 Blower module connector 57992 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 282
6-16). Power off the circuit breakers assigned to the power supplies. Warning To ensure that power remains off while you are performing this procedure, tape the circuit breaker switches in the Off (0) position. 6-38 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497 - Cisco 12406 | Configuration Guide - Page 283
(Figure 6-20). • It is not necessary to remove the power supply from its bay. • Repeat this step for the second power supply. Figure 6-20 Unseating the DC Power Supply OUTPUT OK INPUT OK MISWIRE 101116 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-39 - Cisco 12406 | Configuration Guide - Page 284
screws on the blower module. c. Remove the blower module by grasping it on each side and pulling it straight back from the chassis. Figure 6-21 Removing the Blower Module 1 2 HIGH SPEED BLOWER 129401 6-40 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 285
(+), (c) ground. Figure 6-22 Disconnecting the DC Power Leads POWER A 4 +1 2 GND 3 57993 1 Negative terminal port 2 Positive terminal port 3 Ground terminal port 4 Terminal port connector screws OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-41 - Cisco 12406 | Configuration Guide - Page 286
the PDU at a slight angle makes it easier to remove it from the chassis. Figure 6-23 Removing the DC PDU 57995 Step 7 Install the new PDU and tighten its (4) captive screws to secure it to the chassis. 6-42 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 287
the (4) captive screws to secure the blower module to the chassis. d. Lower the carrying handle to its operating position. Figure 6-24 Installing the Blower Module 1 2 3 129402 HIGH SPEED BLOWER OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-43 - Cisco 12406 | Configuration Guide - Page 288
Leads POWER A 4 +1 2 GND 3 57993 1 Negative terminal port 2 Positive terminal port 3 Ground terminal port 4 Terminal port connector screws Step 10 Power on the circuit breakers assigned to the power supplies. 6-44 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 289
screws to securely seat the power supply to the chassis (Figure 6-26). c. Repeat steps a. and b. for the second power supply. Figure 6-26 Seating a DC Power Supply OUTPUT OK INPUT OK MISWIRE 101117 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-45 - Cisco 12406 | Configuration Guide - Page 290
power supplies. The Output Power OK and Input Power OK indicators on the power supplies should light. If the indicators do not light, see the "Troubleshooting the DC Power Supply Installation" section on page 6-35. 6-46 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 291
Power supply Additional line card information can be found in the installation and configuration note for each type of line card. These notes accompany every line card that ships from the factory as an FRU. 57651 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 292
Fully remove each line card from its slot. Do not allow a line card to rest partially inserted into a slot, because that will damage the EMI shielding on the RP or line card in the slot directly below. 6-48 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 293
faceplate is lined with an EMI-preventive gasket consisting of many raised, conductive contacts. Be careful not to damage the gasket contacts, because a damaged card carrier gasket can reduce EMI performance. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-49 - Cisco 12406 | Configuration Guide - Page 294
, because that will damage the EMI shielding on the RP or line card in the slot directly below. Step 5 Pivot the ejector levers away from each other; rotate each ejector lever outward away from the faceplate. 6-50 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 295
, bare metal surface. Identify the card slot for the new line card. Remove the blank faceplate covering the card slot. If installed, remove the narrow card filler panel at the top of the blank card slot. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-51 - Cisco 12406 | Configuration Guide - Page 296
Router. Figure 6-29 Line Card Cable-Management Bracket ACTIVCEARRRIEXRCELL 0 ACTIVCEARRRIEXRCELL 0 ACTIVCEARRRIEXRCELL 0 ACTIVCEARRRIEXRCELL For fiber-optic or copper cable line cards OC-12/STM-4 POS 66587 6-52 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 297
the threads on the screw or in the insert in the line card faceplate. Step 6 Use a flat-blade screwdriver to secure the two captive screws. Step 7 Repeat Step 2 through Step 6 for any remaining line cards. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-53 - Cisco 12406 | Configuration Guide - Page 298
12/STM-4 POS To reconnect network interface cables to a line card, follow these steps: Step 1 Attach an ESD-preventive strap to your wrist and connect the leash to the chassis or to another grounded, bare metal surface. 6-54 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 299
Router Removing and Installing an RP or a Line Card Step 2 Step 3 Step 4 Step 5 Attach an appropriate number of velcro straps to support the too tightly. Press the velcro strap against itself to secure it. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-55 - Cisco 12406 | Configuration Guide - Page 300
the Switch Fabric Card (product number GSR6-SFC=). You cannot mix 2.5-Gbps switch fabric cards and 10-Gbps switch fabric cards in a chassis. The router will not operate with a mix of switch fabric card types. 6-56 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497 - Cisco 12406 | Configuration Guide - Page 301
the system is powered on. Procedures for removing and installing a CSC are described in these sections: • Removing a Clock and Scheduler Card, page 6-58 • Installing a Clock and Scheduler Card, page 6-59 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-57 - Cisco 12406 | Configuration Guide - Page 302
from the CSC faceplate. Slide the CSC halfway out of the slot, then stop. Touching only the metal card carrier, use your free hand to support the bottom of the CSC. 6-58 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 303
side of the CSC slot. Pivot the ejector levers away from each other; rotate each ejector lever outward away from the faceplate. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-59 - Cisco 12406 | Configuration Guide - Page 304
Chapter 6 Maintaining the Router Removing and Installing a Clock and Scheduler Card, Switch Fabric Card, or Alarm Card SFC status LEDs labeled FAIL • Three router alarm LEDs labeled CRITICAL, MAJOR, MINOR 6-60 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 305
and installing an SFC are described in these sections: • Removing a Switch Fabric Card, page 6-62 • Installing a Switch Fabric Card, page 6-63 • Verifying the Installation of the Switch Fabric Card, page 6-64 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-61 - Cisco 12406 | Configuration Guide - Page 306
from the SFC faceplate. Slide the SFC halfway out of the slot, then stop. Touching only the metal card carrier, use your free hand to support the bottom of the SFC. 6-62 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 307
the front of the card cage, then stop. Pivot the ejector levers toward the faceplate until the connector seats in the backplane. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-63 - Cisco 12406 | Configuration Guide - Page 308
operation after installing a replacement SFC, see the "Verifying the Installation of the Clock and Scheduler Card" section on page 6-60. The description of the LEDs applies equally to checking SFC operation. 6-64 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497 - Cisco 12406 | Configuration Guide - Page 309
and installing an alarm card are described in the following sections: • Removing an Alarm Card, page 6-66 • Installing an Alarm Card, page 6-66 • Verifying the Installation of the Alarm Card, page 6-67 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-65 - Cisco 12406 | Configuration Guide - Page 310
, then stop. Use both thumbs to push the card carrier into the slot until the alarm card connector seats itself against the backplane connector. 6-66 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 311
after installing a replacement alarm card, see the "Verifying the Installation of the Clock and Scheduler Card" section on page 6-60. The description of the LEDs applies equally to checking alarm card operation. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 312
screwdrivers • 9/16-inch (14-mm) wrench • 3/4-inch (19-mm) socket and ratchet wrench • Vacuum cleaner • Antistatic bag or similar ESD-preventive container • Replacement chassis, Part Number: GSR6/120= 6-68 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 313
grounding system to the NEBS supplemental bonding and grounding receptacles on the replacement chassis. For more information, see the "Supplemental Bonding and Grounding Connections" section on page 3-9. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-69 - Cisco 12406 | Configuration Guide - Page 314
only). After disconnecting the cables, either leave them in the cable management bracket for reuse with the new RP, or move them away from the chassis and place them safely aside. 6-70 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 315
RP and line cards • CSCs, SFCs, and alarm cards • Power modules (either AC-input power supplies or DC-input PEMs) • PDU • Blower module Transferring these components is discussed below. Next, the chassis is removed, as explained on page 6-74. Then, the replacement chassis is installed, as explained - Cisco 12406 | Configuration Guide - Page 316
the same slots in the replacement chassis. Note As you install a CSC, an SFC, or an alarm card in the replacement chassis, tighten the captive screws on the card to ensure electromagnetic compliance (EMC). 6-72 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 317
the Power Distribution Unit Follow the instructions in the "Removing and Installing the Chassis" section on page 6-68 to remove the PDU from the defective chassis and install it in the replacement chassis. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-73 - Cisco 12406 | Configuration Guide - Page 318
defective chassis from the equipment rack, examine how the chassis is mounted in the rack: • Mounted directly against the rack flanges, but sitting on the optional rack-mounting brackets (see Figure 3-1 on page 3-4) 6-74 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 319
Equipment Rack, page 6-76 Installing the Chassis on a Tabletop or Flat Surface Install the replacement chassis as instructed in the "Installing the Chassis on a Tabletop or Flat Surface" section on page 3-9. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-75 - Cisco 12406 | Configuration Guide - Page 320
the "Connecting RP and Line Card Cables" section on page 3-11. Reconnecting Alarm Cards Cables Reconnect the cables to the alarm cards as instructed in the "Connecting Alarm Card Cables" section on page 3-13. 6-76 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 321
memory requirements and replacing memory on the Cisco 12000 Series Router RP and line cards. Consult this publication before replacing memory on your RP or line card, or adding memory to your RP or line card. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide 6-77 - Cisco 12406 | Configuration Guide - Page 322
Upgrading the RP and Line Card Memory Chapter 6 Maintaining the Router 6-78 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 323
A-2 on page A-3 • For electrical specifications for systems equipped with the DC-input power subsystem, see Table A-3 on page A-4 • For a list of the environmental specifications, see Table A-4 on page A-5 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide A-1 - Cisco 12406 | Configuration Guide - Page 324
-mount flanges and front door width 2. Including cable-management system and front cover 3. Chassis only 4. Chassis fully configured, using all card slots, AC or DC power supplies, and frosted doors and hinges Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide A-2 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 325
. Contact your local sales representative for assistance. The electrical specifications and values listed in Table A-3 are for a system equipped with the DC-input PDU and DC-input power entry modules (PEMs). OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide A-3 - Cisco 12406 | Configuration Guide - Page 326
, use the on-line power calculator. Failure to properly verify the configuration may result in an unpredictable state if one of the power units fails. Contact your local sales representative for assistance. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide A-4 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 327
from other equipment vented directly into the Cisco 12006 and Cisco 12406 Router air inlet may cause overheating. Install the router so that it is protected from a direct flow of hot air from other equipment. OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide A-5 - Cisco 12406 | Configuration Guide - Page 328
, 10-Gigabit per slot chassis. Table A-6 lists the Cisco 12006 and Cisco 12406 Routers and provides model comparison information based on chassis slot counts, maximum switching capacity, and switch fabric type. Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide A-6 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 329
Specifications Specifications Table A-6 Cisco 12006 and Cisco 12406 Router Model Comparison Model 12406 12006 Chassis Slots Switching Capacity Switch Fabric Identification 6 120 Gbps SFC and CSC 6 30 Gbps SFC-30/120 and CSC-30/120 On Cisco 12000 Series Routers that support switching - Cisco 12406 | Configuration Guide - Page 330
Specifications Appendix A Technical Specifications Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide A-8 OL-11497-03 - Cisco 12406 | Configuration Guide - Page 331
LEDs 4-34 LEDs (figure) 6-61 on/off conditions 6-61 removing and installing (figure) 6-65 procedure 6-65 to 6-67 alphanumeric LED displays GRP 1-22 line cards 4-31 PRP 1-31 using for troubleshooting 4-15 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide IN-1 - Cisco 12406 | Configuration Guide - Page 332
3-40, 6-53, 6-60, 6-67 configuration register value 4-2 copying to RP Flash memory SIMM 3-72 damage to EMI-preventive gaskets 6-49, 6-51, 6-72 description of xv DRAM DIMM installation 1-20, 1-29 IN-2 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03 - Cisco 12406 | Configuration Guide - Page 333
3-69 center-mount brackets, installing on rack 3-5 chassis depth A-2 height A-2 installing in a rack 3-8 lifting (caution) 2-5 outer dimensions 2-11 overview 1-7 to 1-9 removing and installing 6-68 to 6-77 width A-2 Cisco 12006 Series electrical specifications AC-input power supply A-3 DC-input PEM - Cisco 12406 | Configuration Guide - Page 334
12 removing and installing (figure) 6-58 procedure 6-57 to 6-61 verifying operation of replacement CSC 6-60 current rating input AC-input power supply A-3 DC-input PEM A-4 output AC-input power supply A-3 DC-input PEM A-4 IN-4 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 335
4-13 environmental monitoring 1-14 environmental shutdown 4-36 ESD-preventive container 6-59, 6-63, 6-66 Ethernet port 100BASE-T GRP 1-24, 3-22 PRP 1-32 specifications 3-29 10BASE-T GRP 1-24, 3-22 PRP 1-32 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide IN-5 - Cisco 12406 | Configuration Guide - Page 336
description GRP 1-24, 3-22 PRP 1-32 interface configuration 3-59 EXEC command interpreter 3-51 F Fast Ethernet specifications 3-29 features FRU removal 1-5 hot-swappable power modules 1-4 line card support 1-4 NEBS compliance 1-5 OIR 1-4 rear-panel source power connections 1-5 redundant alarm cards - Cisco 12406 | Configuration Guide - Page 337
4-12 inservice testing 5-1 interface parameters, configuring 3-58, 3-61 interrupting system with Break key 4-10 L laser safety information 2-5 LEDs AC-input power supply 1-39, 4-17 alarm card (figure) 6-61 on/off conditions 6-61 alphanumeric LED displays GRP 1-21 PRP 1-30 blower module 1-48 DC - Cisco 12406 | Configuration Guide - Page 338
line frequency, AC-input power supply A-3 locked blocks, recovering from 3-82 M MBus (maintenance bus) description 1-13 module 4-15 overview 1-13 to 1-14 using for troubleshooting 4-15 MDI Ethernet RJ-45 receptacle cable specifications 3-29 pin locations (figure) 3-24 memory components GRP 1-19 PRP - Cisco 12406 | Configuration Guide - Page 339
DC power converters 4-23 MBus modules 4-23 power distribution unit 4-23 power modules 4-23 privileged mode 3-51 processor subsystem, troubleshooting 4-28 PRP alphanumeric LED displays description 3-41 function 1-30 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide - Cisco 12406 | Configuration Guide - Page 340
figure) 3-21 power-on self-test (POST) 4-28 removing and installing 6-47 to 6-51 troubleshooting 4-28 S safety earth ground, missing 2-8 electrical 2-8 extra-low voltage requirements 2-4 lifting 2-5, 6-74, 6-75 IN-10 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497 - Cisco 12406 | Configuration Guide - Page 341
(table) 1-19 PRP (table) 1-28 starting the system 3-39 startup problems, troubleshooting 4-15 supplemental bonding and grounding connection 2-17, 3-9 switch, soft reset (NMI) GRP 1-22 PRP 1-31 switch fabric OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide IN-11 - Cisco 12406 | Configuration Guide - Page 342
-pair wiring 2-20 U uninterruptible power source See UPS UPS 2-14, 2-16 using boot flash command caution 3-48 using handles for lifting (caution) 2-5 V voltage input AC-input power supply A-3 DC-input PEM A-4 output IN-12 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL - Cisco 12406 | Configuration Guide - Page 343
3-14, 3-16 console port 3-14 Ethernet MII port pinout (table) 3-23 Ethernet port connections 3-24 guidelines for working with telephone wiring 2-8 plant wiring 2-20 PRP auxiliary port 3-18 console port 3-18 OL-11497-03 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide IN-13 - Cisco 12406 | Configuration Guide - Page 344
Index IN-14 Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide OL-11497-03
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
 |
 |
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel:
408 526-4000
800 553-NETS (6387)
Fax:
408 527-0883
Cisco 12006 and Cisco 12406 Router
Installation and Configuration Guide
Text Part Number: OL-11497-03