Cisco 2524 Installation Guide
Cisco 2524 - Router - EN Manual
 |
View all Cisco 2524 manuals
Add to My Manuals
Save this manual to your list of manuals |
Cisco 2524 manual content summary:
- Cisco 2524 | Installation Guide - Page 1
chapter describes the tasks you must perform before you begin to install the Cisco 2524 and Cisco 2525 routers, and includes the following sections: • Safety Recommendations • General Site Requirements • Installation Checklist • Creating a Site Log • Preparing to Connect to a Network • Inspecting - Cisco 2524 | Installation Guide - Page 2
the appendix "Translated Safety Warnings.") • Locate the emergency power-off switch for the room in which you are working. Then, if an - Working near power supplies Warning When installing the unit, the ground connection must always be made first and . 2-2 Cisco 2524 and Cisco 2525 Router User Guide - Cisco 2524 | Installation Guide - Page 3
. If no wrist strap is available, ground yourself by touching the metal part of the chassis. Caution For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms (Mohms). Preparing to Install the Cisco 2524 and Cisco 2525 Routers 2-3 - Cisco 2524 | Installation Guide - Page 4
failure. • Ensure that the chassis cover is secure. The chassis is designed to allow cooling air to flow effectively within it. An open chassis allows air leaks, which may interrupt and redirect the flow of cooling air from internal components. 2-4 Cisco 2524 and Cisco 2525 Router User Guide - Cisco 2524 | Installation Guide - Page 5
configuration: • Enclosed racks must have adequate ventilation. Ensure that the rack is not overly congested because each unit • Baffles can help to isolate exhaust air from intake air, which also helps to draw cooling air through the chassis. The best placement Cisco 2524 and Cisco 2525 Routers 2-5 - Cisco 2524 | Installation Guide - Page 6
, refer to the appendix "Translated Safety Warnings.") The Cisco 2524 offers a direct current (DC) power supply. See the section "DC Power Specifications" in the chapter "Installing the Cisco 2524 and Cisco 2525 Routers" for more information. Installation Checklist The Installation Checklist lists - Cisco 2524 | Installation Guide - Page 7
Initial electrical connections established ASCII terminal or PC attached to console port Signal distance limits verified Startup sequence steps completed Initial system operation verified Software image verified Verified by Date Preparing to Install the Cisco 2524 and Cisco 2525 Routers 2-7 - Cisco 2524 | Installation Guide - Page 8
router, update the Site Log to reflect the following: - Configuration changes - Changes and updates to Cisco IOS software - Maintenance schedules and requirements - Corrective maintenance procedures performed - Intermittent problems Safety Warnings.") 2-8 Cisco 2524 and Cisco 2525 Router User Guide - Cisco 2524 | Installation Guide - Page 9
the section "Fractional T1/T1 DSU/CSU Module Port Pinouts" in the appendix "Cabling Specifications for the Cisco 2524 and Cisco 2525 Routers." Warning Network hazardous voltages are present in the BRI, fractional T1/T1, and switched 56 cables. If you detach the cable, detach the end away from the - Cisco 2524 | Installation Guide - Page 10
listed in the section "4-Wire 56/64-kbps DSU/CSU Module Port Pinouts" in the appendix "Cabling Specifications for the Cisco 2524 and Cisco 2525 Routers. Warning Network hazardous voltages are present in the BRI, fractional T1/T1, and switched 56 cables. If you detach the cable, detach the end away - Cisco 2524 | Installation Guide - Page 11
the section "Fractional T1/T1 DSU/CSU Module Port Pinouts" in the appendix "Cabling Specifications for the Cisco 2524 and Cisco 2525 Routers." Warning Network hazardous voltages are present in the BRI, fractional T1/T1, and switched 56 cables. If you detach the cable, detach the end away from the - Cisco 2524 | Installation Guide - Page 12
only by PTO staff or suitably trained engineers. (To see translated versions of this warning, refer to the appendix "Translated Safety Warnings.") Table 2-4 lists the specifications for ISDN BRI cables. 2-12 Cisco 2524 and Cisco 2525 Router User Guide - Cisco 2524 | Installation Guide - Page 13
a special serial cable to connect the router to a modem or DSU/CSU. This cable is available from Cisco and is usually ordered with the system. The cable uses a DB-60 connector on the chassis end. See the appendix "Cabling Specifications for the Cisco 2524 and Cisco 2525 Routers" for cable pinouts - Cisco 2524 | Installation Guide - Page 14
) 200 100 50 50 100 2,050 1,025 513 256 102 50 Distance (Meters) 1,250 625 312 156 78 31 15 Caution The EIA/TIA-449 and V.35 interfaces support data rates up to 2.048 Mbps. Exceeding this maximum could result in loss of data and is not recommended. 2-14 Cisco 2524 and Cisco 2525 Router User Guide - Cisco 2524 | Installation Guide - Page 15
(with a modem). This section discusses important cabling information to consider before connecting a console terminal (an ASCII terminal or PC running terminal emulation software) to the console port or modem to the auxiliary port. Preparing to Install the Cisco 2524 and Cisco 2525 Routers 2-15 - Cisco 2524 | Installation Guide - Page 16
port, see the section "Connecting the Console Terminal and Modem" in the chapter "Installing the Cisco 2524 and Cisco 2525 Routers." See the appendix "Cabling Specifications for the Cisco 2524 and Cisco 2525 Routers" for cable and port pinouts. 2-16 Cisco 2524 and Cisco 2525 Router User Guide - Cisco 2524 | Installation Guide - Page 17
DCE adapter (labeled Modem) • Optional equipment (such as network interface cables and WAN modules) • Cisco Information Packet publication, problems when installing or configuring your system, contact a customer service representative. Preparing to Install the Cisco 2524 and Cisco 2525 Routers - Cisco 2524 | Installation Guide - Page 18
Inspecting the System 2-18 Cisco 2524 and Cisco 2525 Router User Guide
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
CHAPTER
Preparing to Install the Cisco 2524 and Cisco 2525 Routers
2-1
Preparing to Install the
Cisco 2524 and Cisco 2525
Routers
2
This chapter describes the tasks you must perform before you begin to install the
Cisco 2524 and Cisco 2525 routers, and includes the following sections:
•
Safety Recommendations
•
General Site Requirements
•
Installation Checklist
•
Creating a Site Log
•
Preparing to Connect to a Network
•
Inspecting the System
Safety Recommendations
Follow these guidelines to ensure general safety:
•
Keep the chassis area clear and dust-free during and after installation.
•
Put the removed chassis cover in a safe place.
•
Keep tools away from walk areas where you and others could fall over them.
•
Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf
and roll up your sleeves.
•
Wear safety glasses if you are working under any conditions that might be hazardous to
your eyes.
•
Do not perform any action that creates a potential hazard to people or makes the
equipment unsafe.