Cisco 2610XM User Guide

Cisco 2610XM Manual

Get Cisco 2610XM PDF manuals and user guides View all Cisco 2610XM manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco 2610XM manual content summary:

  • Cisco 2610XM | User Guide - Page 1
    Helsinki University of Technology Department of Communications and Networking How to Configure Cisco 2600 Routers Modified by Juha Järvinen [email protected] Zhong Yunqiu 10.6.2004 7.8.2008
  • Cisco 2610XM | User Guide - Page 2
    8 2.1.3 No Form 9 2.2 Open Shortest Path First OSPF 9 2.2.1 OSPF Commands 9 2.2.2 Router ID 10 2.2.3 Virtual Link 11 2.2.4 Configure OSPF Interface Parameters 11 2.2.5 Configure OSPF authentication 12 2.2.6 No Form 12 2.3 RIP and OSPF Redistribution 13 2.3.1 RIP ...13 2.3.2 OSPF ...13
  • Cisco 2610XM | User Guide - Page 3
    2600 Series routers. Mainly this document has been done for Laboratory work course (S-38.133) at Networking Laboratory at HUT. On laboratory course these Cisco's routers are used for IPv4 routing in small network. This document includes configuring interfaces up and routing part, which has manual
  • Cisco 2610XM | User Guide - Page 4
    a different group of related commands. For security purposes, the Cisco IOS software provides two levels of access to commands: user and privileged. The unprivileged user mode is called user EXEC mode. The privileged mode is called privileged EXEC mode and requires a password. The following table
  • Cisco 2610XM | User Guide - Page 5
    enable configure terminal interface etc. Router> Router# Router(config)# Router(config-if)# disable exit, end, Ctrl-Z exit exit, end, Ctrl-Z Figure 1. Four Cisco IOS Operation modes and their accesses and exits as a figure. 1.1.1 User EXEC Mode When you are connected to the router, you are
  • Cisco 2610XM | User Guide - Page 6
    of a keyword or argument. Include a space before the question mark. Router#configure ? memory Configure from NV memory network Configure from a TFTP network host terminal Configure from the terminal You can also abbreviate commands and keywords by entering just enough characters to make the
  • Cisco 2610XM | User Guide - Page 7
    can put them with the following instructions. In privileged EXEC mode give the next command: Router#config terminal Then enter the interface type port to enter the interface configuration mode. Router(config)#interface FastEthernet0/0 Now you are in interface configuration mode and you can modify
  • Cisco 2610XM | User Guide - Page 8
    updates Exit from routing protocol configuration mode Specify flash update threshold in second Description of the interactive help system Specify input queue depth Forward packets over multiple paths Specify a neighbor router Enable routing on an IP network Negate a command or set its defaults Add
  • Cisco 2610XM | User Guide - Page 9
    receive only RIP version 2 packets. Configure an interface to receive RIP version 1 and 2 packets. 2.1.3 No Form To turn off any feature of RIP routing, for example to turn off neighbor 10.12.0.5 255.255.255.252, give the next command: Router(config-router)#no neighbor 10.12.0.5 255.255.255.252 To
  • Cisco 2610XM | User Guide - Page 10
    tag Exit from routing protocol configuration mode Description of the interactive help system Do not complain about specific event Log changes in adjacency state Forward packets over multiple paths Specify a neighbor router Enable routing on an IP network Negate a command or set its defaults Suppress
  • Cisco 2610XM | User Guide - Page 11
    . Router(config-router)#router id 1.1.1.1 It is very recommend checking router's router ID by giving the next command Router#show ip ospf 2.2.3 Virtual Link A Virtual link can be built up for network shown in Figure (2) by 1. Defining Router IDs for the both ends. 2. Giving in router configuration
  • Cisco 2610XM | User Guide - Page 12
    seen before its neighbors declare the OSPF router down. Assign a specific password to be used by neighboring OSPF routers on a network segment that is using OSPF's simple password authentication. 2.2.5 Configure OSPF authentication Cisco router supports message-digest hashing algorithm to guarantee
  • Cisco 2610XM | User Guide - Page 13
    running B routing protocol throughout one or more routers, you have to tell about border area router or gateway router with the following command. B network is generally much bigger and for example the Internet. Router(config-router)#default-information originate 2.3.4 LAN If a LAN is connected
  • Cisco 2610XM | User Guide - Page 14
    the following command in global configuration mode: Router(config)# ip Cisco Express Forwarding patterns in your network. Use the following command to enable it: Router (config) # ip cef accounting load-balance-hash 3.4 Verifying CEF Use the use the following commands in privileged EXEC mode to view
  • Cisco 2610XM | User Guide - Page 15
    cs001.htm [8] Cisco: Configuring Cisco Express Forwarding Load sharing http://www.cisco.com/en/US/tech/tk827/tk831/technologies_tech_note09186a0080094 806.shtml [9] Cisco: Cisco Expressing Forwarding http://www.cisco.com/en/US/docs/ios/11_2/feature/guide/cef.html [10] Cisco: Sample Configuration for
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
Helsinki University of Technology
Department of Communications and Networking
How to Configure Cisco 2600 Routers
Juha Järvinen
10.6.2004
Modified by
Zhong Yunqiu
7.8.2008