Cisco 2611XM Hardware Installation Guide

Cisco 2611XM Manual

Get Cisco 2611XM PDF manuals and user guides
UPC - 746320661216
View all Cisco 2611XM manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco 2611XM manual content summary:

  • Cisco 2611XM | Hardware Installation Guide - Page 1
    Cisco 2600 Series Routers Hardware Installation Guide Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 2
    CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, GigaDrive, GigaStack
  • Cisco 2611XM | Hardware Installation Guide - Page 3
    Definitions of Service Request Severity xix Obtaining Additional Publications and Information xix Overview of Cisco 2600 Series Routers 1-1 Hardware Features 1-1 Reading the Front-Panel LEDs 1-3 Reading the Rear-Panel LEDs 1-5 Modules, Interface Cards, and Memory 1-8 Interface Numbering 1-9 WAN and
  • Cisco 2611XM | Hardware Installation Guide - Page 4
    R Installing the Router 3-1 Installing Modules, Interface Cards, and Power Supplies 3-2 Setting Up the Chassis 3-3 Setting the Chassis on a Desktop 3-3 Mounting the Chassis in a Rack 3-4 Attaching the Brackets to Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series Routers 3-5 Attaching the
  • Cisco 2611XM | Hardware Installation Guide - Page 5
    Configuration Using the CLI (Manual Configuration) 3-28 Troubleshooting A-1 Isolating Problems A-1 Troubleshooting the Power and Cooling Systems A-2 Environmental Reporting Features A-2 Troubleshooting Modules, Cables, and Connections A-3 System Messages A-4 Recovering a Lost Password A-4 Cisco
  • Cisco 2611XM | Hardware Installation Guide - Page 6
    Command B-10 Procedure for the tftpdnld Command B-11 Configuration Register 1-1 Configuration Register Settings 1-1 Changing Configuration Register Settings 1-2 Configuring the Boot Field 1-3 Enabling Booting from Flash Memory 1-5 Cisco 2600 Series Routers Hardware Installation Guide vi OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 7
    more information. This guide describes several router models that are similar in functionality, but differ in the number of interfaces supported. Some information provided may not apply to your particular router model. To access the warranty, service, and support information, see the "Cisco 90-Day
  • Cisco 2611XM | Hardware Installation Guide - Page 8
    Router Troubleshooting Using the ROM Monitor Configuration Register Description Discusses the features and specifications of Cisco 2600 series routers. Discusses environmental requirements, safety recommendations, and describes the various ports and how to prepare for connections between networks
  • Cisco 2611XM | Hardware Installation Guide - Page 9
    manual. Timesaver Means the described action saves time. You can save time by performing the action described in the paragraph. Tip Means the following information will help you solve a problem. The tips information might not be troubleshooting Cisco 2600 Series Routers Hardware Installation Guide ix
  • Cisco 2611XM | Hardware Installation Guide - Page 10
    qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Warnung sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE Cisco 2600 Series Routers Hardware Installation Guide x OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 11
    som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide xi
  • Cisco 2611XM | Hardware Installation Guide - Page 12
    åelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco 2600 Series Routers Hardware Installation Guide xii OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 13
    Preface Safety Warnings OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide xiii
  • Cisco 2611XM | Hardware Installation Guide - Page 14
    Cisco IOS software running your Cisco 2600 series router includes extensive features and functionality. For information that is beyond the scope of this document, or for additional "Obtaining Documentation" section on page xvii. Cisco 2600 Series Routers Hardware Installation Guide xiv OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 15
    Product Cisco 2600 series routers Network management system Cisco IOS software Document Title Cisco 2600 Series Modular Routers Quick Start Guide Cisco Modular Access Router Cable Specifications Cisco Redundant Power System Hardware Installation Guide Quick Start Guide: Network Modules for Cisco
  • Cisco 2611XM | Hardware Installation Guide - Page 16
    . d. Review the document online, or click the PDF icon to download and print the document in Adobe Portable Document Format (PDF). You can also contact the Cisco service and support website for assistance: http://www.cisco.com/public/Support_root.shtml. Duration of Hardware Warranty Ninety (90) days
  • Cisco 2611XM | Hardware Installation Guide - Page 17
    Cisco Sales and Service Representative. Complete the information below, and keep it for reference: Company product purchased from Company telephone number Product model number Product serial number Maintenance contract number Obtaining Documentation Cisco documentation and additional literature
  • Cisco 2611XM | Hardware Installation Guide - Page 18
    ID or password, you can register at this URL: http://tools.cisco.com/RPF/register/register.do Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support
  • Cisco 2611XM | Hardware Installation Guide - Page 19
    guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL: http://www.cisco.com/go/marketplace/ • The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog
  • Cisco 2611XM | Hardware Installation Guide - Page 20
    . Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in
  • Cisco 2611XM | Hardware Installation Guide - Page 21
    - Cisco 2621 - Token Ring (RJ-45) - - - - 1 1 - - - Fast Ethernet (10/100) - 1 - 2 - - 1 1 2 Network Module Slot 1 1 1 1 1 1 1 1 1 WAN Interface Card Slots 2 2 2 2 2 2 2 2 2 Advanced Integration Module Slots 1 1 1 1 1 1 1 1 1 OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide
  • Cisco 2611XM | Hardware Installation Guide - Page 22
    - Cisco 2651 - Cisco 2651XM - Cisco 2691 - Token Ring (RJ-45 Fast Ethernet (10/100) 2 1 1 2 2 2 Network Module Slot 1 1 1 1 1 1 WAN Interface Card Slots 2 2 2 2 2 3 Advanced Integration Module Slots 1 1 1 1 1 2 In addition to the interfaces listed in Table 1-1, Cisco 2600 series routers
  • Cisco 2611XM | Hardware Installation Guide - Page 23
    Router Rear Panel-Example of 2RU Router TD RD LP AL CD TD RD LP AL CD 72056 NM-HDV AL BANK 4 BANK 3 BANK 2 VWIC 2MFT-E1 BANK 1 BANK 0 CTRLR E2 LP CD CTRLR E1 SEE IBMNEASFNTOAURLAELLATION V0 EN ACT 100 Mbps LINK SEE MANUAL BEFORE INSTALLATION DSU 56K FAST ETHERNET 0/1 FAST ETHERNET
  • Cisco 2611XM | Hardware Installation Guide - Page 24
    Routers Table 1-2 Cisco 2600 Series Routers with 1-RU Chassis Height-Front-Panel LED Descriptions LED Description (continued) RPS Off-No RPS1 is attached. On-RPS is attached and operational. Blinking-RPS is attached, but has a failure. ACTIVITY Off-In the Cisco IOS software, but no network
  • Cisco 2611XM | Hardware Installation Guide - Page 25
    on the router model. Figure 1-5 Cisco 2611-Rear-Panel LEDs Link ACT LED LED SERIAL 1 SERIAL 0 SEE MANUAL BEFORE INSTALLATION WIC CONN 2A/S LINK W0 LINK SEE MANUAL BEFORE INSTALLATION ACT LOOP BACK WIC 2A/S ETHERNET 0/1ACT ETHERNET 0/0 CONSOLE AUX Cisco 2610 Ethernet 0/0 10Base-T port
  • Cisco 2611XM | Hardware Installation Guide - Page 26
    SEE MANUAL BEFORE INSTALLATION WIC CONN 2A/S FDX W0 Cisco 2621 10/100 ETHERNET 0/1 10/100 ETHERNET 0/0 CONSOLE AUX 10/100BASE-T Ethernet 0/1 (RJ-45) 10/100BASE-T Ethernet 0/0 (RJ-45) Auxiliary port (RJ-45) Console port (RJ-45) 14326 Cisco 2600 Series Routers Hardware Installation Guide
  • Cisco 2611XM | Hardware Installation Guide - Page 27
    Table 1-4 Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series Routers-Rear-Panel LEDs LED LINK ACT FDX 100 Mbps Description When on, a link has been established with the hub or switch at the other end of the cable. Packets are being transmitted or received on the Ethernet interface. When
  • Cisco 2611XM | Hardware Installation Guide - Page 28
    Modules, Interface Cards, and Memory Figure 1-10 Cisco 2691-Rear-Panel LEDs Chapter 1 Overview of Cisco 2600 Series Routers TD RD LP AL CD TD RD LP AL CD 72011 ACT 100 Mbps LINK SEE MANUAL BEFORE INSTALLATION DSU 56K FAST ETHERNET 0/1 FAST ETHERNET 0/0 ACT CF1 100 Mbps LINK SEE MANUAL
  • Cisco 2611XM | Hardware Installation Guide - Page 29
    Integration Modules in Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers • For information about installing DRAM, SDRAM, NVRAM, and flash memory SIMMs, refer to the following hardware configuration note: - Upgrading System Memory, Internal Flash Memory, and Root ROM in Cisco 2600
  • Cisco 2611XM | Hardware Installation Guide - Page 30
    SERIAL W0 AUX Cisco 2612 65 3 4 15000/6-024H0zV- 1A 47 W Figure 1-12 shows a router of 2-RU height with: • A 2-port T1 network module in slot 1 (containing the following ports: T1 1/0 and T1 1/1) • Two built-in Ethernet 10/100 interfaces-Fast Ethernet 0/0 and Fast Ethernet 0/1 • A WIC in each
  • Cisco 2611XM | Hardware Installation Guide - Page 31
    Overview of Cisco 2600 Series Routers System Specifications Voice Interface Numbering Voice interfaces are numbered as follows: chassis-slot/voice-module-slot/voice-interface If a 4-channel voice network module is installed in chassis slot 1, the voice interfaces are: • 1/0/0-Chassis slot 1/Voice
  • Cisco 2611XM | Hardware Installation Guide - Page 32
    Compliance Chapter 1 Overview of Cisco 2600 Series Routers Table 1-7 Cisco 2691 System Specifications Description Specification Dimensions (H x W x D) 3.46 x 17.07 x 11.20 in. (8.78 x 45.36 x 28.45 cm), two rack unit height Weight 15 lb (6.80 kg) Input voltage, AC power supply 100 to 120
  • Cisco 2611XM | Hardware Installation Guide - Page 33
    the equipment unsafe. Safety with Electricity Follow these guidelines when working on equipment powered by electricity: Warning Read the installation instructions before connecting the system to the power source. Statement 1004 OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide 2-1
  • Cisco 2611XM | Hardware Installation Guide - Page 34
    strap is available, ground yourself by touching a metal part of the chassis. Caution For the safety of your equipment, periodically check the resistance value of the antistatic strap. It should be between 1 and 10 megohms (Mohm). Cisco 2600 Series Routers Hardware Installation Guide 2-2 OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 35
    routers. Table 2-1 Power Requirements for Cisco 2600 Series Routers Power Source AC DC Input Power 100 - 240 VAC, 1.0 A, 50 - 60 Hz 48 - 60 VDC, 3.0 A Input Voltage Tolerance Limits 85 - 264 VAC 38 - 72 VDC Site Environment The router can be placed on a desktop or mounted in a rack. Single rack
  • Cisco 2611XM | Hardware Installation Guide - Page 36
    of 1 RU can be installed in 19-, 23-, and 24-inch racks. Cisco 2600 series routers with chassis height of 2 RU can be installed in 19- or 23-inch racks. The following information will help you plan your equipment rack configuration: • Enclosed racks must have adequate ventilation. Ensure that the
  • Cisco 2611XM | Hardware Installation Guide - Page 37
    site power check completed Required tools available Additional equipment available Router received The appropriate quick start guide for your router received Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Regulatory Compliance and Safety Information document received Product
  • Cisco 2611XM | Hardware Installation Guide - Page 38
    RJ-45-to-DB-25 adapter cable for modem connection • Ethernet cable • Optional equipment (such as network connection cables or additional rack-mount brackets) • Cisco 2600 Series Modular Routers Quick Start Guide • Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Regulatory Compliance and
  • Cisco 2611XM | Hardware Installation Guide - Page 39
    to the Cisco Modular Access Router Cable Specifications document online or on the Documentation CD-ROM. • Ethernet hub or PC with a network interface card for connection to Ethernet (LAN) ports. • Console terminal (an ASCII terminal or a PC running terminal emulation software) configured for 9600
  • Cisco 2611XM | Hardware Installation Guide - Page 40
    to the following online documents for more information about network connections and interfaces: • Cisco Network Modules Hardware Installation Guide • Cisco Interface Cards Installation Guide • Cisco Modular Access Router Cable Specifications Warning To avoid electric shock, do not connect safety
  • Cisco 2611XM | Hardware Installation Guide - Page 41
    - Cisco 2611 2 Cisco 2611XM - Cisco 2612 1 Cisco 2613 - Cisco 2620 - Cisco 2620XM - Cisco 2621 - Cisco 2621XM - Cisco 2650 - Cisco 2650XM - Cisco 2651 - Cisco 2651XM - Cisco 2691 - Token Ring (RJ-45) - - - - 1 1 Fast Ethernet (10/100) - 1 - 2 - - 1 1 2 2 1 1 2 2 2 Network Module
  • Cisco 2611XM | Hardware Installation Guide - Page 42
    Pinouts" in the Cisco Modular Access Router Cable Specifications online document for the Token Ring port pinouts. This document is available online and on the Cisco Documentation CD-ROM. Serial Connections Serial connections are provided by WAN interface cards and network modules. The WAN interface
  • Cisco 2611XM | Hardware Installation Guide - Page 43
    of the pins on the DB-60 serial connector), cable pinouts are provided in the Cisco Modular Access Router Cable Specifications. Distance Limitations Serial signals can travel a limited distance at any given bit rate; generally, the slower the data rate, the greater the distance. All serial signals
  • Cisco 2611XM | Hardware Installation Guide - Page 44
    ISDN. Table 2-5 lists the specifications for ISDN BRI cables. Also, refer to the Cisco Modular Access Router Cable Specifications online document for pinouts. This document is located on Cisco.com and the Documentation CD-ROM. 2-12 Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 45
    to Install the Router Preparing to Connect to a Network Table 2-5 ISDN-BRI Cable Specifications Specification Resistance (at 96 kHz) Capacitance (at 1 kHz) Impedance (at 96 kHz) Wire diameter Distance limitation 1. nF = nanoFarad High-Capacitance Cable Low-Capacitance Cable 160 ohms/km
  • Cisco 2611XM | Hardware Installation Guide - Page 46
    Preparing to Connect to a Network Chapter 2 Preparing to Install the Router 2-14 Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 47
    Installing the Router CH A P T E R 3 This chapter guides you through the installation of Cisco 2600 series routers and includes the following sections: • Installing Modules, Interface Cards, and Power Supplies, page 3-2 • Setting Up the Chassis, page 3-3 • Installing the Chassis Ground Connection
  • Cisco 2611XM | Hardware Installation Guide - Page 48
    the applicable documents online. For network modules: • Quick Start Guide: Network Modules for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers • Cisco Network Modules Installation Guide For WICs and VICs: • Quick Start Guide: Interface Cards for Cisco 1600, 1700, 2600, 3600, and
  • Cisco 2611XM | Hardware Installation Guide - Page 49
    Power Supplies in Cisco 2691 Routers For external power supplies: • Cisco RPS Hardware Installation Guide Note If there are modules, interface cards, or power supplies to be removed or installed, we recommend that you perform the installation or removal before you install the chassis. If a chassis
  • Cisco 2611XM | Hardware Installation Guide - Page 50
    ground connection procedures, see the "Installing the Chassis Ground Connection" section on page 3-13. Mounting the Chassis in a Rack This section describes the procedures for rack-mounting the chassis. Cisco 2600 series routers with a chassis height of 1 rack-unit (1RU) ship with brackets for use
  • Cisco 2611XM | Hardware Installation Guide - Page 51
    23-Inch Rack-Mounting of Routers with 2-RU Height 23" ETSI, NEBS RIGHT 23" ETSI, NEBS LEFT Slots for cable tie attachment 82532 For chassis side opposite fans For chassis side with fans Attaching the Brackets to Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series Routers To install
  • Cisco 2611XM | Hardware Installation Guide - Page 52
    -Front Panel Forward (19-Inch Rack with a 17.75-Inch Opening or a 23- or 24-Inch Rack) 62881 Note: The second bracket attaches to the other side of the chassis. Brackets for 19-inch rack Brackets for 23-inch or 24-inch rack Cisco 2600 Series Routers Hardware Installation Guide 3-6 OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 53
    (19-Inch Rack with a 17.75-Inch Opening or a 23- or 24-Inch Rack) 110V 60 Hz 1.6A MAX Note: The second bracket attaches to the other side of the chassis. Brackets for 19-inch rack Brackets for 23-inch or 24-inch rack 72014 OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide 3-7
  • Cisco 2611XM | Hardware Installation Guide - Page 54
    23-inch or 24-inch rack Figure 3-11 Center-Mount Bracket Installation-Front Panel Forward (19-Inch Rack with a 17.5-Inch Opening or a 23- or 24-Inch Rack) Note: The second bracket attaches to the other side of the chassis. Cisco 2600 Series Routers Hardware Installation Guide 3-8 Brackets for 19
  • Cisco 2611XM | Hardware Installation Guide - Page 55
    SEE MANUAL BEFORE INSTALLATION DSU 56K SEE MANUAL BEFORE INSTALLATION Right (wide) bracket for 19-inch rack Left (narrow) bracket for 19-inch rack Four screws are required on each side. Left bracket for 23-inch rack 82692 OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide 3-9
  • Cisco 2611XM | Hardware Installation Guide - Page 56
    , load the rack from the bottom to the top with the heaviest component at the bottom of the rack. • If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006 3-10 Cisco 2600 Series Routers Hardware Installation Guide
  • Cisco 2611XM | Hardware Installation Guide - Page 57
    the narrow shoulder faces the router chassis. Note The hex-head screws and plastic washers are used only for wall-mounting the router. For rack-mounting, the brackets are attached using Phillips-head screws, without washers. OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide 3-11
  • Cisco 2611XM | Hardware Installation Guide - Page 58
    front and rear of the chassis vertically. • Position the end nearest the power cable at the top. • Align the screws (not included) with a wall stud, or use wall anchors. • Figure 3-17 shows a typical wall-mounted installation. 3-12 Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 59
    Router Figure 3-17 Mounting the Chassis on the Wall Installing the Chassis Ground Connection 100-240V- 1A 50/60 Hz 47 W Cisco 2611 W0 LINK ETHERNET 1 ACT LINK ETHERNET 0 ACT CONSOLE AUX CONN 2A/S WIC SEE MANUAL terminal. OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide 3-13
  • Cisco 2611XM | Hardware Installation Guide - Page 60
    DSU 56K ACT 100 Mbps LINK FAST ETHERNET 0/1 FAST ETHERNET 0/0 ACT CF1 100 Mbps LINK TD RD LP AL CD TD RD LP AL CD SEE MANUAL BEFORE INSTALLATION DSU 56K SEE MANUAL BEFORE INSTALLATION CISCO2691 CONSOLE AUX 3-14 Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 61
    FAST ETHERNET 0/1 FAST ETHERNET 0/0 ACT CF1 100 Mbps LINK SEE MANUAL BEFORE INSTALLATION DSU 56K SEE MANUAL BEFORE INSTALLATION CISCO2691 CONSOLE AUX After the router has been installed and properly grounded, you can connect the power wiring; the WAN, LAN, and voice cables; and the cables
  • Cisco 2611XM | Hardware Installation Guide - Page 62
    a DC-input power supply. Note For installations compliant with the National Electric Code, AWG 14 (2.0 mm2) wire is required for DC input and safety ground wire. Table 3-1 DC Wiring Requirements for Cisco 2600 Series Routers Router DC Input Cisco 2600 with -48 to -60 VDC, 4 A2 1-RU chassis
  • Cisco 2611XM | Hardware Installation Guide - Page 63
    . Figure 3-22 DC Power Connections for Cisco 2600 Series Routers (Typical) On/off switch Negative Ground Positive 72363 -+ Terminal block Step 4 Step 5 Secure the wires using cable ties. Turn on power to the DC circuit. OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide 3-17
  • Cisco 2611XM | Hardware Installation Guide - Page 64
    detail in the following documents: • Cisco Modular Access Router Cable Specifications • Cisco Network Modules Installation Guide • Cisco Interface Cards Installation Guide Table 3-2 WAN, LAN, and Voice Connections Port or Connection Ethernet T1/E1 WAN Cisco serial Cisco Smart serial DSL Port Type
  • Cisco 2611XM | Hardware Installation Guide - Page 65
    -through 1. Refer to the Cisco Modular Access Router Cable Specifications for information about selecting these cables. LAN, WAN, and Voice Connection Procedures Connect each WAN, LAN, and voice cable to the appropriate connector on the chassis or on a network module or interface card. • Position
  • Cisco 2611XM | Hardware Installation Guide - Page 66
    pinouts, refer to the Cisco Modular Access Router Cable Specifications document available online and on the Documentation CD-ROM. Note On the Cisco routers, the console port is color-coded blue. Step 2 Configure your terminal or PC terminal emulation software for 9600 baud, 8 data bits, no parity
  • Cisco 2611XM | Hardware Installation Guide - Page 67
    Cable Specifications document available online and on the Documentation CD-ROM. Note On the Cisco routers, the auxiliary port is color-coded black. Step 2 Make sure that your modem and the auxiliary port on the router are configured for the same transmission speed (up to 115200 bps is supported
  • Cisco 2611XM | Hardware Installation Guide - Page 68
    the Router SERIAL 1 CONN SERIAL 0 SEE MANUAL BEFORE INSTALLATION WIC CONN 2A/S SERIAL 1 CONN SERIAL 0 SEE MANUAL BEFORE INSTALLATION WIC CONN 2A/S W0 Cisco 2611 LINK ETHERNET 1 ACT LINK ETHERNET 0 ACT CONSOLE AUX 100-240V- 1A 50/60 Hz 47 W AUX port (RJ-45) Modem cable Modem RJ
  • Cisco 2611XM | Hardware Installation Guide - Page 69
    are ready to power up the Cisco router if the following steps are completed: • Chassis is securely mounted. • Power and interface cables are connected. • Your PC terminal emulation program is configured for 9600 baud, 8 data bits, 1 stop bit, and no parity. • You have selected passwords for access
  • Cisco 2611XM | Hardware Installation Guide - Page 70
    LED on the front of the chassis comes on. • The fan operates. Depending on your installation, Fast Ethernet (0/0, 0/1) and Network Module (Active, Ready) LEDs might also come on. If you encounter problems when you power up the router, see Appendix A, "Troubleshooting." Messages begin to appear in
  • Cisco 2611XM | Hardware Installation Guide - Page 71
    CLI or use Cisco Router and Security Device Manager to perform additional configuration. See the "Initial Configuration Using the Setup Command Facility" section on page 3-26. • Command-line interface (CLI). If you prefer to use the Cisco IOS CLI, see the "Initial Configuration Using the CLI (Manual
  • Cisco 2611XM | Hardware Installation Guide - Page 72
    router and network, and it creates an initial configuration file.The prompts vary, depending on your router model, the installed interface modules, and the software image. The following example and the user entries (in bold) are shown as examples only. For a description of the interface numbering
  • Cisco 2611XM | Hardware Installation Guide - Page 73
    appropriate for your network: Configure SNMP Network Management? [yes]: Community string [public]: A summary of the available interfaces is displayed: Note The interface numbering that appears is dependent on the type of Cisco modular router platform and on the installed interface modules and cards
  • Cisco 2611XM | Hardware Installation Guide - Page 74
    the initial configuration tasks, your Cisco router is ready to configure for specific functions. For configuration procedures, refer to the Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers. or the Cisco IOS software configuration documentation. You
  • Cisco 2611XM | Hardware Installation Guide - Page 75
    installed on the router at the factory. To use SDM to configure the router, refer to the quick start guide that shipped with your router. You can also access the Cisco2600 series routers quick start guides online at the following URL: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod
  • Cisco 2611XM | Hardware Installation Guide - Page 76
    Configuring the Router Chapter 3 Installing the Router 3-30 Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 77
    the router as the source of the problem. • Isolating Problems, page A-1 • System Messages, page A-4 • Recovering a Lost Password, page A-4 • Cisco Technical Assistance Center, page A-4 Note To troubleshoot a network module, refer to the Cisco Network Modules Installation Guide; to troubleshoot a WAN
  • Cisco 2611XM | Hardware Installation Guide - Page 78
    Isolating Problems Appendix A Troubleshooting • Modules-LEDs on the modules can help identify a failure. • Cables-External cables that connect the router to the network. Troubleshooting the Power and Cooling Systems Both the system LED and the fans can help you troubleshoot a power problem. Check
  • Cisco 2611XM | Hardware Installation Guide - Page 79
    cable connections. - Make sure that you have a version of Cisco IOS software that supports the network module and interface card. Check the Cisco Network Modules Installation Guide and the Cisco Interface Cards Installation Guide or accompanying configuration notes for the affected network module
  • Cisco 2611XM | Hardware Installation Guide - Page 80
    Troubleshooting System Messages This section describes system error and recovery messages that may appear when operating a Cisco 2600 series router. Error messages for Cisco 2600 series routers powered by the Cisco redundant power system are described in the publication Cisco RPS Installation Guide
  • Cisco 2611XM | Hardware Installation Guide - Page 81
    power up or restart a Cisco router. During normal operation, the ROM monitor helps to initialize the processor hardware and boot the operating system software. You can also use the ROM monitor to: • Help isolate hardware problems encountered when installing your router. • Download a new Cisco IOS
  • Cisco 2611XM | Hardware Installation Guide - Page 82
    boot up an external process set/show/clear the breakpoint configuration register utility continue executing a downloaded image display the context of a loaded image display contents of cookie PROM in hex list the device table Cisco 2600 Series Routers Hardware Installation Guide B-2 OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 83
    instruction stream dnld serial download a program module frame print out a selected stack frame help monitor builtin command help history monitor command history iomemdef set IO mem to a default 25% meminfo main memory information repeat repeat a monitor command reset system reset
  • Cisco 2611XM | Hardware Installation Guide - Page 84
    enough to support the necessary interfaces), the router boots from flash memory, and then the larger image is downloaded from the TFTP server. Entering Boot Commands The boot command syntax is as follows, where: • partition is a partition number in the flash memory. • filename is the Cisco IOS image
  • Cisco 2611XM | Hardware Installation Guide - Page 85
    in the third partition in compact flash memory in slot 1. • boot filename tftpserver- Boots from the specified Cisco IOS image on the specified TFTP server (after first booting from flash). For example: boot c2600-i-mz 172.15.19.11 Note Use the CLI commands show version and show hardware to see the
  • Cisco 2611XM | Hardware Installation Guide - Page 86
    the router, similar to power on. tftpdnld-(Except Cisco 2691) Downloads an image using TFTP from a remote server. See the "Copying an Image from a TFTP Server Using the tftpdnld Command" procedure on page B-10. Debugging Commands Most debugging commands are functional only when Cisco IOS software
  • Cisco 2611XM | Hardware Installation Guide - Page 87
    confreg command: rommon 7> confreg Configuration Summary enabled are: break/abort has effect console baud: 9600 boot: the ROM Monitor do you wish to change the configuration? y/n [n]: y enable "diagnostic mode"? y/n [n]: y enable "use net in IP bcast address"? y/n [n]: enable "load rom after netboot
  • Cisco 2611XM | Hardware Installation Guide - Page 88
    to the factory default: rommon 7> confreg 0x2102 You must reset or power cycle the router for new configuration to take effect. Recovering Cisco IOS Software Images If your Cisco router experiences difficulties and no longer contains a valid Cisco IOS software image in flash memory, you can download
  • Cisco 2611XM | Hardware Installation Guide - Page 89
    console port using the instructions in the "Connecting to a Console Terminal or Modem" section on page 3-20. Power up the router. The power-on self-test diagnostics run and the boot ROM searches for a valid boot image and Cisco IOS image in flash memory. If the boot image and Cisco IOS image are not
  • Cisco 2611XM | Hardware Installation Guide - Page 90
    Command The tftpdnld command downloads a Cisco IOS software image from a remote server accessible from a FastEthernet, Ethernet, or Token Ring network interface on a Cisco 2600 series router (except Cisco 2691). The tftpdnld command downloads the Cisco IOS software image into flash memory using TFTP
  • Cisco 2611XM | Hardware Installation Guide - Page 91
    a Fast Ethernet network interface. • TR_SPEED_MODE-Sets the Token Ring speed and duplex mode. 0=4 Mbps half-duplex mode, 1=4 Mbps full-duplex mode, 2=16 Mbps half-duplex mode, and 3=16 Mbps full-duplex mode. The default is 2. OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide B-11
  • Cisco 2611XM | Hardware Installation Guide - Page 92
    command for disaster recovery only. WARNING: all existing data in all partitions on flash will be lost! Do you wish to continue? y/n: [n]: Enter y to download the Cisco IOS software image. When the process is complete, the ROM monitor mode prompt appears on your screen. rommon 7> The router is now
  • Cisco 2611XM | Hardware Installation Guide - Page 93
    • Enabling Booting from Flash Memory, page C-5 Configuration Register Settings The router has a 16-bit configuration register in NVRAM. You can use the configuration register to perform the following tasks: • Set and display the configuration register value • Force the router into the ROM monitor
  • Cisco 2611XM | Hardware Installation Guide - Page 94
    to the online document Cisco Modular Access Router Cable Specifications. This document is available online and on the Cisco Documentation CD-ROM. Configure your terminal or terminal emulation software for 9600 baud (default), 8 data bits, no parity, and 1 stop bit. Power on the router. When asked if
  • Cisco 2611XM | Hardware Installation Guide - Page 95
    Stays at the ROM monitor on a reload or power cycle Boots the first image in flash memory as a system image Enables default booting from flash memory Enables boot system commands that override default booting from flash memory OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide C-3
  • Cisco 2611XM | Hardware Installation Guide - Page 96
    of the list is reached. If there are no boot commands in the configuration file, the router attempts to boot the first file in flash memory. In the following example, the configuration register is set to boot the router automatically from flash memory and to ignore Break at the next reboot of the
  • Cisco 2611XM | Hardware Installation Guide - Page 97
    the filename, the router is configured to boot from flash memory. To enter configuration mode while in the system software image, enter the configure command at the enable prompt as in the following example: Router# configure Configuring from terminal, memory, or network [terminal]? terminal Enter
  • Cisco 2611XM | Hardware Installation Guide - Page 98
    Enabling Booting from Flash Memory Appendix C Configuration Register Cisco 2600 Series Routers Hardware Installation Guide C-6 OL-2171-06
  • Cisco 2611XM | Hardware Installation Guide - Page 99
    B-4 booting from Flash memory 1-5 bracket attachment rack-mount 3-5 to 3-10 wall-mount 3-11 OL-2171-06 INDEX C cables, provided 2-6 Caution symbol, meaning of ix chassis desktop installation 3-3 grounding 3-13 rack-mounting 3-4 wall-mounting 3-11 Cisco IOS software locating documentation
  • Cisco 2611XM | Hardware Installation Guide - Page 100
    A-4 ESD 2-2 Ethernet cable types 2-9 F FDX LED 1-7 feet, installing 3-3 Figures auxiliary port connection 3-22 bracket attachment for rack -mounting 3-6 to 3-10 bracket attachment for wall-mounting 3-12 brackets, rack mounting 3-4, 3-5 chassis views 1-2, 1-3 console terminal connection 3-21 DC power
  • Cisco 2611XM | Hardware Installation Guide - Page 101
    the chassis 3-13 Flash memory booting from 1-5 description of 1-2 frame command B-6 G grounding the chassis 3-13 H help command B-2, B-5 high temperature, troubleshooting A-2 humidity, specifications 1-11, 1-12 I i (initialize) command B-6 installation checklist 2-4 desktop 3-3 rack-mounting
  • Cisco 2611XM | Hardware Installation Guide - Page 102
    memory 1-2 show hardware command B-5 show version command B-5 site configuration 2-4 environment 2-3 IN-4 Cisco 2600 Series Routers Hardware Installation Guide log, record keeping 2-5 requirements 2-3 slot numbering 1-11 software image recovery procedure B-8 specifications Cisco 261x, Cisco
  • Cisco 2611XM | Hardware Installation Guide - Page 103
    2-6 troubleshooting cables A-3 connections A-3 cooling system A-2 error messages A-4 front panel LEDs 1-3 high temperature A-2 modules A-3 power system A-2 rear panel LEDs 1-5 V ventilation 2-4 VICs See voice interface cards. voice interface cards, installing 1-8 W wall-mounting the chassis 3-11
  • Cisco 2611XM | Hardware Installation Guide - Page 104
    Index IN-6 Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Cisco 2600 Series Routers
Hardware Installation Guide
Text Part Number: OL-2171-06