Cisco IDS 4210 User Guide

Cisco IDS 4210 - Intrusion Detection Sys 4210 Sensor Manual

Get Cisco IDS 4210 - Intrusion Detection Sys 4210 Sensor PDF manuals and user guides
UPC - 746320401669
View all Cisco IDS 4210 manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco IDS 4210 manual content summary:

  • Cisco IDS 4210 | User Guide - Page 1
    IDS-4210 before July 2003, you must upgrade the memory to 512 MB to install Cisco IPS 5.x. for more information, see Upgrading the Memory, page 2-3. Note IDS-4210 does not support inline (IPS) mode. Caution The BIOS on IDS-4210 is specific to IDS-4210 and must only be upgraded under instructions
  • Cisco IDS 4210 | User Guide - Page 2
    Installing IDS-4210 Front and Back Panel Features and Indicators Figure 2-1 shows the front panel indicators on IDS-4210 startup or when a system fault is detected. Blinks when hard-disk drive activity occurs Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 2-2 OL-8677-01
  • Cisco IDS 4210 | User Guide - Page 3
    -K9, and IDS-4210-NFR must have 512 MB of RAM to support Cisco IPS 5.1. If you are upgrading an existing IDS-4210, IDS-4210-K9, or IDS-4210-NFR to 5.1, you must insert one additional 256-MB DIMM (part number IDS-4210-MEM-U) to upgrade the memory to the required 512 MB minimum. Note Do not install
  • Cisco IDS 4210 | User Guide - Page 4
    Upgrading the Memory Chapter 2 Installing IDS-4210 Step 6 Step 7 Remove the chassis cover by unscrewing the screw on the front of the cover and sliding the cover straight back. Locate the DIMM sockets and select the empty DIMM socket next to the existing DIMM. Note The existing DIMM is installed
  • Cisco IDS 4210 | User Guide - Page 5
    Safety Information for the Cisco Intrusion Prevention System 4200 Series Appliance Sensor. Note If you purchased an IDS-4210 before July 2003, you must upgrade the memory to 512 MB to install Cisco IPS 5.x. For more information, see Upgrading the Memory, page 2-3. To install IDS-4210 on the network
  • Cisco IDS 4210 | User Guide - Page 6
    Power on IDS-4210. Initialize IDS-4210. For the procedure, see Initializing the Sensor, page 10-2. Upgrade IDS-4210 to the latest Cisco IPS software. For the procedure, see Obtaining Cisco IPS Software, page 11-1. You are now ready to configure intrusion detection on the appliance. Installing Cisco
  • Cisco IDS 4210 | User Guide - Page 7
    • Documentation and software - Cisco IDS recovery/upgrade CD - Cisco Documentation CD - Documentation Roadmap for Cisco Intrusion Prevention System 5.1 - Regulatory Compliance and Safety Information for the Cisco Intrusion Prevention System 4200 Series Appliance Sensor Installing and Removing the
  • Cisco IDS 4210 | User Guide - Page 8
    holes to be used To install the center mount brackets in a two-post, open-frame relay rack, follow these steps: Step 1 Determine where you want to place IDS-4210. Step 2 Mark the upper and lower mounting positions on the two posts. Installing Cisco Intrusion Prevention System Appliances and Modules
  • Cisco IDS 4210 | User Guide - Page 9
    the side of IDS-4210 (see Figure 2-3). Figure 2-3 Installing Center Mount Brackets Pan- Secure the bracket to IDS-4210 chassis using two screws (see Figure 2-3 on page 2-9). Step 5 Repeat Step 4 to install the remaining bracket on the other side of IDS-4210. OL-8677-01 Installing Cisco Intrusion
  • Cisco IDS 4210 | User Guide - Page 10
    Secure IDS-4210 to the rack using a screw through the mounting bracket to the front of the left and right posts (see Figure 2-3 on page 2-9). Installing install the front mount brackets in a two-post, open-frame relay rack: • Two chassis support Installing Cisco Intrusion Prevention System Appliances and Modules 5.1
  • Cisco IDS 4210 | User Guide - Page 11
    support brackets on IDS-4210 into the rack mounting brackets attached to the rack. Use the bolts provided with the rack to fasten the front flanges of IDS-4210 to the rack. Note When you are done, IDS-4210 should not slide on the channel bar. OL-8677-01 Installing Cisco Intrusion Prevention
  • Cisco IDS 4210 | User Guide - Page 12
    Installing the Accessories Chapter 2 Installing IDS-4210 2-12 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
CH A P T E R
2-1
Installing Cisco Intrusion Prevention System Appliances and Modules 5.1
OL-8677-01
2
Installing IDS-4210
This chapter describes IDS-4210 and how to install it and its accessories.
Note
IDS-4215 replaced IDS-4210, which is no longer sold.
Note
If you purchased an IDS-4210 before July 2003, you must upgrade the memory to 512 MB to install
Cisco IPS 5.x. for more information, see
Upgrading the Memory, page 2-3
.
Note
IDS-4210 does not support inline (IPS) mode.
Caution
The BIOS on IDS-4210 is specific to IDS-4210 and must only be upgraded under instructions from Cisco
with BIOS files obtained from the Cisco website. Installing a non-Cisco or third-party BIOS on
IDS-4210 voids the warranty. For more information on how to obtain instructions and BIOS files from
the Cisco website, see Obtaining
Obtaining Cisco IPS Software, page 11-1
.
This chapter contains the following sections:
•
Front and Back Panel Features and Indicators, page 2-2
•
Upgrading the Memory, page 2-3
•
Installing IDS-4210, page 2-5
•
Installing the Accessories, page 2-7