Compaq 500 Hardware Reference Guide - Compaq 500B/505B
Compaq 500 Manual
View all Compaq 500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Compaq 500 manual content summary:
- Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 1
580407-001 Upgrading and Servicing Guide - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 2
- Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 3
Removing and Replacing the Front Bezel - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 4
Removing and Replacing the Front Bezel 10-15 MINUTES Before you begin Tools Needed: z Flathead screwdriver z Phillips screwdriver Flathead screwdrivers A flathead screwdriver can be used with the screw seen in the following illustration. CAUTION: Static electricity can damage the electronic - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 5
. 2 Disconnect all cables and remove all items from the computer: z Disconnect cables for power, keyboard, mouse, monitor, etc. z Remove items such as memory cards, USB drives, etc. 4 Grasp the handle on the side cover and pull towards the back of the computer. Slide the cover about 2.4 cm (1 inch - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 6
6 Pull each of the three side tabs that secure the front bezel to the computer, to release the front bezel. Replacing the Front Bezel IMPORTANT: The new (replacement) part may not look the same as the original part, due to different manufacturers or models. Hewlett-Packard always provides quality - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 7
3 The tabs fit into slots and over the front lip of the computer. 5 Reattach the thumb screw at the back of the computer. 4 To reattach the panel, align the tabs on the panel over the corresponding slots on the computer and lay the panel into place. Slide the side cover forward. 6 Connect the - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 8
8 Removing and Replacing the Front Bezel - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 9
Removing and Replacing Memory - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 10
cables and remove all items from the computer: z Disconnect cables for power, keyboard, mouse, monitor, etc. z Remove items such as memory cards, USB drives, etc. CAUTION: Static electricity can damage the electronic components inside the computer. Discharge static electricity by touching the metal - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 11
4 Grasp the handle on the side cover and pull towards the back of the computer. Slide the cover about 2.4 cm (1 inch) to remove it. 6 Lay the computer on its side. 5 Remove the side panel by lifting it away from the computer. 7 Locate the memory sockets on your computer motherboard. NOTE: The - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 12
9 Touching only the memory module, lift it out of the socket. Replacing Memory NOTE: The new (replacement) part may not look exactly the same as the original part, due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 13
3 Position the memory module over the socket, aligning the notch with the tab in the socket, and then firmly press the module down into the socket. 5 The side panel has several tabs on its top, bottom, and leading edges. ...until the retaining clips at the ends of the socket lock the module into - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 14
7 To reattach the panel, align the tabs on the panel over the corresponding slots on the computer. Slide the side cover forward. 8 Reattach the screw at the back of the computer. 9 Connect the cables, such as the keyboard, mouse, Ethernet, and monitor cables. 10 Reconnect the power cord. 11 Turn - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 15
Removing and Replacing an Optical Disc Drive - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 16
Removing and Replacing an Optical Disc Drive 15-20 MINUTES Before you begin Tools Needed: z Flathead screwdriver z Phillips screwdriver Flathead screwdrivers A flathead screwdriver can be used with the screw seen in the following illustration. CAUTION: Static electricity can damage the electronic - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 17
Disconnect all cables and remove all items from the computer: z Disconnect cables for power, keyboard, mouse, monitor, etc. z Remove items such as memory cards, USB drives, etc. 4 Remove the side cover by loosening the screw that connects the cover to the computer. 3 Remove any discs in the drive - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 18
6 Remove the side panel by lifting it away from the computer. 8 Swing the front bezel out to remove from the computer. 7 Pull each of the three side tabs that secure the front bezel to the computer, to release the front bezel. 9 Locate the optical disc drives at the top front of the computer. 10 - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 19
11 Push the drive slightly forward. 13 Pull the disc drive out through the front of the computer. 12 Disconnect the power (1) and data (2) cables by squeezing the latch on the connector and pulling to remove. Removing and Replacing an Optical Disc Drive 19 - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 20
Replacing an Optical Disc Drive IMPORTANT: The new (replacement) part may not look the same as the original part, due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Push the replacement disc drive - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 21
7 The tabs fit into slots and over the front lip of the computer. 9 Reattach the screw at the back of the computer. 8 To reattach the panel, align the tabs on the panel over the corresponding slots on the computer. Slide the side cover forward. 10 Connect the cables, such as the keyboard, mouse, - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 22
22 Removing and Replacing an Optical Disc Drive - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 23
Removing and Replacing a Hard Disk Drive - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 24
Removing and Replacing a Hard Disk Drive 25-30 MINUTES Before You Begin Observe the following requirements before removing and replacing a hard disk drive. IMPORTANT: A hard disk drive is extremely sensitive to shock impact. Do not bang or drop it. Do not touch the circuit board. Static electricity - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 25
. 2 Disconnect all cables and remove all items from the computer: z Disconnect cables for power, keyboard, mouse, monitor, etc. z Remove items such as memory cards, USB drives, etc. 4 Grasp the handle on the side cover and pull towards the back of the computer. Slide the cover about 2.4 cm (1 inch - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 26
6 Pull each of the three side tabs that secure the front bezel to the computer, to release the front bezel. 8 Locate the external drive bay at the front of the computer, below the optical drive bays. 7 Swing the front bezel out to remove from the computer. 9 Disconnect the power (1) and data (2) - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 27
10 Remove the two screws that secure the hard disk drive to the computer. 12 Remove the hard drive from the computer. 11 Pull the hard drive out of the front of the computer. 13 Carefully remove the replacement hard disk drive from the electrostatic bag and place the failed hard disk drive into - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 28
Replacing a Hard Disk Drive NOTE: The replacement hard drive may not look exactly the same as the original drive due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Slide the replacement hard disk drive - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 29
5 To replace the front bezel, align the left side of the bezel and swing the front bezel toward the computer to close it. 7 The tabs fit into slots and over the front lip of the computer. 6 The side panel has several tabs on its top, bottom, and leading edges. 8 To reattach the panel, align the - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 30
9 Reattach the screw at the back of the computer. 12 Turn on the computer and all peripherals, such as the monitor. 13 Verify that the replacement hard disk drive works properly. 10 Connect the cables, such as the keyboard, mouse, Ethernet, and monitor cables. 11 Reconnect the power cord. 30 - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 31
Removing and Replacing an Add-In Card - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 32
Removing and Replacing an Add-In Card 15-20 MINUTES Before you begin Tools Needed: z Flathead screwdriver z Phillips screwdriver Flathead screwdrivers A flathead screwdriver can be : Computer features may vary by model. IMPORTANT: System board may vary. 32 Removing and Replacing an Add-In Card - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 33
. 2 Disconnect all cables and remove all items from the computer: z Disconnect cables for power, keyboard, mouse, monitor, etc. z Remove items such as memory cards, USB drives, etc. 4 Grasp the handle on the side cover and pull towards the back of the computer. Slide the cover about 2.4 cm (1 inch - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 34
6 Locate the add-in cards at the back of the computer. 8 On the back of the computer, remove the screw from the bracket cover for the add-in cards. 7 Lay the computer on its side. 9 Remove the bracket cover. 34 Removing and Replacing an Add-In Card - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 35
10 If you are removing a graphics card, press on the latch to release it. 13 Lift the card out of the computer. 11 Remove the graphics card from the card slot. 14 If present, remove any cables connected to the add-in card. 12 For other add-in cards, move the card back and forth gently to free it - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 36
or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Replace any cables previously removed from the card. 3 If you are replacing a graphics card, verify that the latch in the computer snaps back into place. 2 Align the edge of the - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 37
to the back of the computer. 8 The tabs fit into slots and over the front lip of the computer. Removing and Replacing an Add-In Card 37 - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 38
cables. 12 Reconnect the power cord. 13 Turn on the computer and all peripherals, such as the monitor. 14 Verify that the new add-in card is working properly. 10 Reattach the screw at the back of the computer. 38 Removing and Replacing an Add-In - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 39
Removing and Replacing a Power Supply - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 40
Removing and Replacing a Power Supply 20-25 MINUTES Before you begin Tools Needed: z Flathead screwdriver z Phillips screwdriver Flathead screwdrivers A flathead screwdriver can be used with the screw seen in the following illustration. CAUTION: Static electricity can damage the electronic - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 41
. 2 Disconnect all cables and remove all items from the computer: z Disconnect cables for power, keyboard, mouse, monitor, etc. z Remove items such as memory cards, USB drives, etc. 4 Grasp the handle on the side cover and pull towards the back of the computer. Slide the cover about 2.4 cm (1 inch - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 42
6 Before removing the power supply carefully note its orientation in the computer. IMPORTANT: The replacement power supply will need to be placed in the same position. 7 Place the computer on its side. IMPORTANT: Noting the location, type and orientation of the power connectors is extremely - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 43
11 The motherboard power connector has a latch that must be pressed to detach the connector from the motherboard. 13 Some connectors may have latches that must be pressed to remove them. 12 Detach the motherboard power connector from the motherboard. 14 Remove all other power connectors from the - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 44
15 Set the computer upright. 18 Pull the power supply back and tilt it out of the computer. 16 Detach the four screws that connect the power supply to the computer. 17 Use a screwdriver to press the latch at the bottom of the power supply to release it. 44 Removing and Replacing a Power Supply - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 45
is oriented the same way as the original power supply. Align it towards the guide and the ledge, then slide it back until it locks into place next the four screws on the rear of the computer. 1 There is a latch, a guide, and a ledge on the computer that help secure the power supply in the computer. - Compaq 500 | Hardware Reference Guide - Compaq 500B/505B - Page 46
5 The side panel has several tabs on its top, bottom, and leading edges. 7 To reattach the panel, align the tabs on the panel over the corresponding slots on the computer. Slide the side cover forward. 6 The tabs fit into slots and over the front lip of the computer. 8 Reattach the screw at the
Upgrading and Servicing Guide
580407-001