Compaq Presario SR1000 Upgrading and Servicing Guide
Compaq Presario SR1000 - Desktop PC Manual
View all Compaq Presario SR1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Compaq Presario SR1000 manual content summary:
- Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 1
Upgrading and Servicing Guide - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 2
All rights are reserved. No part of this document may be disassembly is prohibited. Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098, and 4,907,093 licensed for limited viewing uses only. Microsoft and Windows are U.S. Registered trademarks of Microsoft Corporation. HP supports - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 3
Replacing Drives 3 Removing a Drive 4 Replacing or Adding a Drive 5 Adding Memory 7 Removing a Memory Module 7 Installing a Memory Module 8 Removing or Installing an Add-In Card 8 Removing an Add-In Card 9 Installing an Add-In Card 9 Replacing the Battery 10 Upgrading and Servicing Guide - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 4
iv Upgrading and Servicing Guide - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 5
Support Guide before installing and connecting your system to the electrical power system. Opening and Closing the PC • Write down and save the system model and serial numbers . Read the following items before attempting to upgrade or service the PC. • These procedures assume familiarity with the - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 6
the PC chassis. 2 Ensure that the hole for the thumbscrew aligns with the hole in the chassis, and replace the thumbscrew (D). Removing the Front Panel This procedure is necessary only when removing or replacing an optical drive, memory card reader, diskette drive, or the hard disk drive. 1 Press - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 7
(blank plate) or a CD-ROM, CD-RW, DVD-ROM, DVD+RW/+R, or combination drive C Memory card reader (select models) D Diskette (floppy) drive (select models) E Front connector panel (no replacement instructions) F Hard disk drive G Second hard disk drive (select models) Upgrading and Servicing Guide 3 - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 8
For a second hard disk drive, remove the two screws (3) and then slide the drive part way back out of the bay (4). Disconnecting the Optical Drive Cables Disconnecting the Memory Card Reader Drive Cable Removing the Second Hard Disk Drive 4 Upgrading and Servicing Guide Disconnecting the Diskette - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 9
Parallel ATA Hard Disk Drive Cables 5 Pull the drive out of the drive bay. 6 If you are replacing the old drive with a new drive, remove the four guide screws (two on each side) from the old drive. You need these screws to install the new drive. Replacing or Adding a Drive 1 If necessary, remove the - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 10
a second hard disk drive, slide the drive into the bay (with connectors facing out) and align the screw holes (3). Insert the two screws (4). Connecting the Memory Card Reader Drive Cable Connecting the Diskette (Floppy) Drive Cables 6 Reconnect the power and data cables to your drive as indicated - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 11
type of DDR memory module depends on which model PC you have. A DDR DIMM To determine which type and speed of memory module your PC uses, and for specific memory module information and specifications, go to the Web site listed in your Warranty and Support Guide and click the Support link. WARNING - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 12
each board/card in the computer. The total +5 V current draw in a fully loaded system (one with all add-in card slots filled) must not exceed the total number of slots multiplied by 2 amps. A Phillips screwdriver is needed to remove, replace, or add an add-in card. 8 Upgrading and Servicing Guide - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 13
and close the PC. See "Opening and Closing the PC" on page 1. NOTE: If the new card or device isn't working, read through the card manufacturer's installation instructions, and recheck all connections, including those to the card, power supply, keyboard, and monitor. Upgrading and Servicing Guide 9 - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 14
CR2032 battery in the socket, with the positive (+) side facing the latch. 7 Replace memory modules or cables you removed. 8 Set the chassis upright. 9 Complete the procedures to replace the side panel, and to close the PC. See "Opening and Closing the PC" on page 1. 10 Upgrading and Servicing Guide - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 15
Upgrading and Servicing Guide 11 - Compaq Presario SR1000 | Upgrading and Servicing Guide - Page 16
Printed in
Upgrading and
Servicing Guide