Cub Cadet 1X 221 HP 1X 221 HP Operator's Manual

Cub Cadet 1X 221 HP Manual

Get Cub Cadet 1X 221 HP PDF manuals and user guides View all Cub Cadet 1X 221 HP manuals
Add to My Manuals
Save this manual to your list of manuals

Cub Cadet 1X 221 HP manual content summary:

  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 1
    Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Model 221 HP Model 221 LHP Single-Stage Snow Thrower - Models 221 HP & 221 LHP WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 2
    To The Owner 1 Thank You Thank you for purchasing a Cub Cadet Snow Thrower. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 3
    and safe operation practices in this manual and on the machine and be trained and supervised by an adult. 4. Never allow adults to operate this machine without proper instruction. 5. Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 4
    not overload machine capacity by attempting to clear g. Replace gasoline cap and tighten securely. snow at too fast of manual, use care and good judgment. Contact Customer Support for 3. The control levers must operate easily in both directions assistance and the name of your nearest servicing
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 5
    common cause of injury associated with snow throwers. Never use your hand to manual for instructions. 7. Maintain or replace safety and instruction labels, as necessary. 8. Observe proper disposal laws and regulations for gas, oil inspected annually by an authorized service dealer to ensure that all
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 6
    on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR'S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING- ROTATING BLADES Keep hands out of inlet and discharge openings while
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 7
    5W-30 Oil One Engine Operator's Manual • One Chute Rotation Control Assembly • One Electric Starter Cord (If equipped) NOTE: This Operator's Manual covers several models. Snow thrower features may vary by model. Not all features in this manual are applicable to all snow thrower models and the
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 8
    tighten the previously removed hardware to secure the handle in place. See Figure 3-2. On model 221 LHP proceed with step 4. Tab Figure 3-4 4. The handle on model 221 LHP can be set in three different 2. Remove the hex washer screws in the chute base. See position. Place the handle in the desired
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 9
    assembly. See Figure 3-8. Figure 3-8 Figure 3-6 3. Remove the screw and hex lock nut from the universal Installing the Chute Rotation Control Assembly (Model 221 LHP only) joint. See Figure 3-9. 1. Remove the four hex washer screws from the back of the handle (two on each side). See Figure
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 10
    manual bag. 2. Place the eye bolt and handle knob on the upper handle as shown in Figure 3-11. Do not fully tighten the hardware until instructed to do so. Recoil Starter Handle Eye Bolt Handle Knob Figure 3-11 NOTE: The opening of the eye bolt should face toward the back of the snow thrower
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 11
    features in this manual are applicable to all snow thrower models and the snow thrower depicted may differ from yours. NOTE: All references to the left or right side of the snow thrower are from the operator's position. Any exceptions will be noted. Chute Tilt Control (Model 221 LHP) The chute tilt
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 12
    Manual for instruction on starting, stopping and operating the engine. Engaging the Auger 1. To engage the auger and start throwing snow, squeeze the auger control against the handle. Release to stop the auger. See Figure 5-1. Chute Controls (Model 221 LHP associated with snow throwers. Never use
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 13
    Chute Control (Model 221 HP) Refer to Figure 5-3 for the chute controls. Upper Chute Chute Control Handle Wing Nut Figure 5-3 To increase the angle/distance snow is thrown, pull up/back on the upper chute. To decrease the angle/distance snow is thrown, push down/forward on the upper chute. To
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 14
    rotating, see the Service section for instructions on replacing the belt. Reversible Shave Plate Figure 6-1 4. Tip the snow thrower back to the operating and pull the handle several times to ensure that any oil trapped in the head is removed. CAUTION: Oil may come out of the spark plug hole when it
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 15
    help hold it in place. NOTE: An oil drain extension kit is available separately. Contact your local Cub Cadet dealer or contact Cub Cadet's Customer Support for kit #753-06684. 3. Change the oil and/or the spark plug as instructed in your Engine Operator's manual. 4. Re-install the lower panel by
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 16
    Service 7 Replacing Belt 1. Run the snow thrower until the fuel tank is empty. 2. Pull the recoil starter handle until resistance is felt. Then tip the snow thrower replace the belt follow these instructions and refer to Figure 7-3: that any oil trapped in the head is removed. CAUTION: Oil may come
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 17
    as instructed in the Maintenance & Adjustments section. 2. Secure the replacement rubber paddles to the auger using the hardware removed earlier. 6. Tighten securely once adjusted. Engine Refer to the Engine Operators manual packed separately with your snow thrower for service information
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 18
    Troubleshooting 8 Problem Excessive vibration Cause 1. Loose parts or damaged auger. Snow thrower fails to selfpropel Augers continue to rotate Snow thrower fails to discharge snow as needed. If the problem persists, take snow thrower to an authorized service dealer. 1. Adjust auger control
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 19
    634-04347 Wheel Assembly, 8" 925-1629 Lamp, #1156 (Model 221 LHP) 751-14006 Fuel Cap 731-05632 Key Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual downloads are also available free of charge at www
  • Cub Cadet 1X 221 HP | 1X 221 HP Operator's Manual - Page 20
    FOR SNOW THROWERS, CHIPPER-SHREDDERS, CHIPPER-SHREDDER VACUUMS, LOG SPLITTERS AND JET SWEEPS The limited warranty set forth below is given by Cub Cadet not genuine Cub Cadet parts. e. Service completed by someone other than an authorized service dealer. f. Transportation charges and service calls.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
O
PERATOR
’
S
M
ANUAL
Safe Operation Practices • Set-Up • Operation •
Maintenance • Service • Troubleshooting •
Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
Single-Stage Snow Thrower — Models 221 HP & 221 LHP
Model 221 HP
Model 221 LHP
Form No. 769-08241
(June 6, 2012)