Cub Cadet 2X 933 SWE 2X 930 SWE Operator's Manual

Cub Cadet 2X 933 SWE Manual

Get Cub Cadet 2X 933 SWE PDF manuals and user guides View all Cub Cadet 2X 933 SWE manuals
Add to My Manuals
Save this manual to your list of manuals

Cub Cadet 2X 933 SWE manual content summary:

  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 1
    Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Two Stage Snow Thrower - Models 930 SWE & 933 SWE WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 2
    Owner 1 Thank You Thank you for purchasing a Snow Thrower manufactured by Cub Cadet. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 3
    and safe operation practices in this manual and on the machine and be trained and supervised by an adult. 4. Never allow adults to operate this machine without proper instruction. 5. Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 4
    on steep slopes. hot or running. 10. Plan your snow-throwing pattern to avoid discharge e. Allow engine to cool manual, use and automatically return to the disengaged position when care and good judgment. Contact Customer Support for released. assistance and the name of your nearest servicing
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 5
    snow throwers snow from machine and prevent freeze up of auger/impeller. 10. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer etc. 11. Always refer to the operator's manual for proper instructions service
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 6
    on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR'S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING- ROTATING BLADES Keep hands out of inlet and discharge openings while
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 7
    information regarding shear pin replacement. 4. NOTE: All references in this manual to the left or right side of the snow thrower is from the operating position only. Exceptions, if any, will be upper holes to firmly secure the upper handle and support tubes. See Figure 3-2. Figure 3-2 Figure 3-1 7
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 8
    3-3. 6. Check that the chute cables are properly routed through the cable guide on top of engine shroud. See Figure 3-5. Chute Crank Bracket Figure 3-5 onto chute base as shown in Figure have been included with your snow thrower. There are holes 3-4. Make sure that the chute notches engage with
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 9
    , the cable should have very little slack. It should NOT be tight. Refer to Figure 3-9. 2. In a well-ventilated area, start the snow thrower engine as instructed in engine operator's manual. Make sure the throttle is set in the FAST position. 3. While standing in the operator's position (behind the
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 10
    the engine turned off, move the speed selector lever into sixth (6) position. Refer to Figure 3-9. 2. With the wheel drive control released, push the snow thrower forward, then pull it back. The machine should move freely. 3. Engage the drive control and attempt to move the machine both forward and
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 11
    on all engine controls, refer to the separate Engine Operator's Manual supplied with this unit. Speed Selector Lever The speed selector faster. Augers When engaged, the augers rotate and draw snow into the auger housing. Chute Assembly Snow drawn into the auger housing is discharged out the chute
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 12
    forward or backward. Figure 4-1 Chute Directional Control The chute directional control is located on the left side of the snow thrower. • To change the direction in which snow is thrown, crank clockwise to discharge to the left and counterclockwise to discharge to the right. • Move the lever
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 13
    clean the chute assembly and chute opening: 1. Release both the Auger Control and the Drive Control. 2. Stop the engine as instructed in the engine operator's manual included with the snow thrower. 3. Remove the clean-out tool from the clip which secures it to the rear of the auger housing. 4. Use
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 14
    Operation 5 Starting and Stopping the Engine Refer to the Engine Operator's Manual packed with your snow thrower for instructions on starting and stopping the engine. To Engage Drive 1. With the throttle control in the Fast (rabbit) position, move shift lever into one of the
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 15
    ! Before servicing, repairing, Manual Maintenance included with the snow thrower. Shave Plate and Skid Shoes The shave plate and skid shoes on the bottom of the snow thrower located on the wheel axle tube behind the wheel axle support bracket. Rubber Friction Wheel Hex Shaft Aluminum Drive Plate
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 16
    pin. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. 1. If augers do not turn Two replacement shear pins and cotter pins have been provided with the snow thrower. Spray an oil lubricant into shaft before inserting new pins and securing
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 17
    as instructed earlier in this . 2. Store in a clean, dry area. 3. If storing the snow thrower in an unventilated area, rustproof the machine using a light oil or silicone to coat the snow thrower. 4. Clean the exterior of the engine and the snow thrower. NOTE: Refer to the engine operator's manual
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 18
    Service Belt Replacement Belt Removal Preparation 1. Remove the chute crank rod the three self-tapping screws. See Figure 7-2. Figure 7-3 Auger Belt Replacement To remove and replace your snow thrower's auger belt, proceed as follows: 1. Remove the bow-tie clip and flat washer from the ferrule
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 19
    the brake bracket assembly towards the cable guide roller and unhook the auger cable "Z" shaft. 12. If also replacing the drive belt, proceed to the "Drive Belt" instruction. If not, reposition the transmission frame back onto the auger housing. Install the drive pulley. Section 7 - Service 19
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 20
    snow thrower. 14. Re-install the belt cover. Drive Belt Replacement If not already done, remove the auger drive belt from the front pulley of the engine double pulley. Refer to "Auger Belt Replacement" instructions Slide Hex Shaft Out Right Side Hex Shaft Figure 7-10 20 Section 7- Service
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 21
    If the sprocket fell from the snow thrower chain while 6. Lift the snow thrower down to its normal operating position. Figure 7-11 IMPORTANT: Repeat the drive control test from the Assembly & Set-Up section of this manual before operating the snow assembly in the snow thrower frame. Insert
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 22
    may need to have the carburetor, and other fuel system components, serviced or replaced. 1. Remove all of the fuel from the fuel tank . 2. Change the engine oil as instructed in the Maintenance section of the Engine Operator's Manual included with the snow thrower. 3. Remove the spark plug and pour
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 23
    Troubleshooting 8 Problem Excessive vibration Cause 1. Loose parts or damaged auger. Loss of power 1. Spark plug wire loose. 2. Gas cap vent hole plugged. Unit fails to propel itself 1. Drive control cable in need of adjustment. Unit fails to discharge snow 2. Drive belt loose or damaged.
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 24
    , 30-inch Shave Plate, 33-inch 731-05632 Key 951-10292 Spark Plug Phone (800) 965-4CUB (4282) to order replacement parts or a complete Parts Manual (have your full model number and 24 serial number ready). Parts Manual downloads are also available free of charge at www.cubcadet.com.
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 25
    Accessories 10 The following attachments and accessories are available for your Cub Cadet 900 series snow thrower. See your Cub Cadet dealer or the retailer from which you purchased your snow thrower for information regarding price and availability. Model Number Description 490-241-0013 OEM-390
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 26
    INC required maintenance listed in your Owner's Manual. MTD recommends that you retain all engine to an Authorized MTD Service Dealer as soon as a problem exists. The warranted repairs should replacement as required maintenance in the written instructions required by Subsection (c) must be warranted
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 27
    (6) The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station. (7) The engine manufacturer is liable for damages to other engine components proximately caused by
  • Cub Cadet 2X 933 SWE | 2X 930 SWE Operator's Manual - Page 28
    FOR SNOW THROWERS The Cub Cadet for use with the product(s) covered by this manual will void your warranty as to any resulting damage. Normal and tires. HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE, through your local authorized service dealer. To locate the dealer
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Printed In USA
Safe Operation Practices • Set-Up • Operation •
Maintenance • Service • Troubleshooting •
Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
O
PERATOR
’
S
M
ANUAL
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
FORM NO. 769-08124
(April 30, 2012)
Two Stage Snow Thrower — Models 930 SWE & 933 SWE