Home » CyberPower Manuals » UPS » CyberPower RMCARD400 » Manual Viewer

CyberPower RMCARD400 Quick Start Guide

CyberPower RMCARD400 Manual

View all CyberPower RMCARD400 manuals

Add to My Manuals
Save this manual to your list of manuals

CyberPower RMCARD400 manual content summary:

CyberPower RMCARD400 | Quick Start Guide - Page 1
Card RMCARD400 RMCARD401 RMCARD400 Universal Link TxC/RyxberPower RMCARD401 Universal Link TxC/RyxbeUrPSBower SAVE THESE INSTRUCTIONS Please read this guide and follow the instructions for installation and use. Copyright © 2022 Cyber Power Systems, Inc. All rights reserved. K01-0000975
CyberPower RMCARD400 | Quick Start Guide - Page 2
1. Hardware Installation 3 Step 2. Conﬁgure the IP Address 4 WEB INTERFACE 6 Login User Account 6 FIRMWARE UPGRADE 6 RESET TO FACTORY DEFAULT SETTING/ RECOVER FROM A LOST PASSWORD 9 SOFTWARE SUPPORT 10 TROUBLESHOOTING 1 1 CONFORMANCE APPROVALS 12 i
CyberPower RMCARD400 | Quick Start Guide - Page 3
models which have smart slot. (RMCARD401 supports the new speciﬁc UPS models) Unpacking Inspect the Remote Management Card upon receipt. The package should contain the following: µCyberPower Remote Management Card µRJ45/DB9 Serial Port Connection Cable µQuick Start Guide µSpare Jumper 1
CyberPower RMCARD400 | Quick Start Guide - Page 4
Front Panel RMCARD400 RMCARD400 1 2 Universal Link Tx/Rx 3 4 RMCARD401 2 RMCARD401 1 5 Universal Link Tx/Rx USB 3 1. Universal Port 2. Ethernet Port 3. Tx/Rx Indicator 4. Link Indicator 5. USB Port 4 LED Status Indicators Link LED Condition The Remote Management Card is not O
CyberPower RMCARD400 | Quick Start Guide - Page 5
. Connect one end to the Universal port on the RMCARD and the other end into the sensor. For more information, please see the ENVIROSENOR user's manual. 3 CARD400 sal CTyxb/RexrPower
CyberPower RMCARD400 | Quick Start Guide - Page 6
Step 2. Conﬁgure the IP Address for the CyberPower Remote Management Card Method 1: Using the Power Device Network Utility 2 1. Install the Power Device Network Utility 2 available for download at www.CyberPower.com. 2. After installation completes, run the "Power Device Network Utility 2". 3. The
CyberPower RMCARD400 | Quick Start Guide - Page 7
6. You can modify the IP Address, Subnet Mask, and Gateway address for the Device MAC Address listed in the Device Network Settings window, as shown in Figure 3. The factory default IP Address is 192.168.20.177 and the default Subnet Mask is 255.255.255.0. Figure 3. The Device Network setting window
CyberPower RMCARD400 | Quick Start Guide - Page 8
access read only features but cannot change any settings. For detailed descriptions and explanations of the Web UI, please refer to RMCARD User's Manual. FIRMWARE UPGRADE By upgrading the ﬁrmware, you can obtain both the new features and updates/improvements to existing functionality. To ensure the
CyberPower RMCARD400 | Quick Start Guide - Page 9
Using Power Device Network Utility Install the CyberPower Power Device Network Utility 2 available for download at www.CyberPower.com. 1 . After installation completes, run the "Power Device Network Utility 2". 2 . The main window of the Power Device Network Utility 2 program is shown in Figure 4.
CyberPower RMCARD400 | Quick Start Guide - Page 10
6 . Select the Firmware and click "OK" to implement ﬁrmware upgrade, as shown in Figure 5. Figure 5. The File Locations of Firmware & Data window. 7 . If the ﬁrmware upgrade is implemented, you will see the Result in the main window, as shown in Figure 6. Figure 6. Firmware upgrade success in the
CyberPower RMCARD400 | Quick Start Guide - Page 11
RESET TO FACTORY DEFAULT SETTING/RECOVER FROM A LOST PASSWORD To reset the CyberPower Remote Management Card to its factory default setting (including web log-in user name and password), please follow these steps: RESET JUMPER RMCARD400/401 1. Remove the card from the UPS without turning the UPS o .
CyberPower RMCARD400 | Quick Start Guide - Page 12
/401 is designed for the 43x18mm (1.69x0.71 inch) SNMP card expansion port of CyberPower PR, OR, and 1-3kVA OL series UPS. SOFTWARE SUPPORT PowerPanel® Business Remote is used to perform a graceful operating system shutdown when protected by a UPS with a remote management card installed. PowerPanel
CyberPower RMCARD400 | Quick Start Guide - Page 13
TROUBLESHOOTING Problem Solution Unable to conﬁgure the Remote Management Card IP Address using method 1 or method 2 1. Check the LED status, it is normal when the yellow
CyberPower RMCARD400 | Quick Start Guide - Page 14
the user will be required to correct the interference at his own expense. Any special accessories needed for compliance must be speciﬁed in the instruction. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
CyberPower RMCARD400 | Quick Start Guide - Page 15
disposed of separately from ordinary household wastes at its end of life. Contact your related WEEE management authority, local o ce, or your household waste disposal service about information on the recycling drop o site. 13
CyberPower RMCARD400 | Quick Start Guide - Page 16
11F., No.26, Jinzhuang Rd., Neihu Dist., Taipei City 114, Taiwan Tel: +886 2 8792 9510 | Fax: +886 2 8792 9621 Email: [email protected], [email protected] All Other Regions Please visit our website for local contact information. Copyright © 2022 Cyber Power Systems, Inc. All rights