D-Link DAP-3711 Product Manual 1

D-Link DAP-3711 Manual

Get D-Link DAP-3711 PDF manuals and user guides View all D-Link DAP-3711 manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DAP-3711 manual content summary:

  • D-Link DAP-3711 | Product Manual 1 - Page 1
    Version 1.00 | 25/12/2020 User Manual 5 km Long Range 802.11ac Wireless Bridge DAP-3711
  • D-Link DAP-3711 | Product Manual 1 - Page 2
    16 Web-based Configuration 17 Wizard 20 Basic Settings 25 Wireless 25 Network 32 D-Link DAP-3711 User Manual In the Network tab, you can set up the DAP-3711's network mode and IP address 32 QoS 34 Service 37 System 40 Status 42 Info 42 Statistics 44 Network 45 Syslog Info 46 Tools
  • D-Link DAP-3711 | Product Manual 1 - Page 3
    Range 802.11ac Wireless Bridge 24V PoE Injector Power cord Mounting ties Quick Start Guide Note: Using a PoE Injector with a different voltage rating or PoE injector than the one included with the DAP-3711 will cause damage and void the warranty for this product. D-Link DAP-3711 User Manual 3
  • D-Link DAP-3711 | Product Manual 1 - Page 4
    with the following: • Microsoft Windows®, Apple Mac OS, or a Linux-based operating system Browser Requirements: • Microsoft Edge, Firefox 60.0, Safari ,or Chrome 68.0.3440.106 D-Link DAP-3711 User Manual 4
  • D-Link DAP-3711 | Product Manual 1 - Page 5
    DAP-3711 also support TDMA. TDMA technology solves the problems of hidden-node problem in the 802.11 network. ACK Time-Out Auto Adjust can automatically detect the distances of the DAP-3711 devices, and thus adjust the wireless parameters to achieve the best wireless link Link DAP-3711 User Manual 5
  • D-Link DAP-3711 | Product Manual 1 - Page 6
    supply • Waterproof housing and protection from weather • Web-based configuration, easy to use • Support dual backup firmware, maintenance operation will be safer and more reliable • Web based working scenario selection makes the installation and setting much easier D-Link DAP-3711 User Manual 6
  • D-Link DAP-3711 | Product Manual 1 - Page 7
    DAP-3711 uses a proprietary PoE injector which is needed to function correctly. Only use the included PoE injector as other power sources such as 3rd party PoE injector es or hubs may damage the DAP-3711 or cause it to operate unreliably and will also void the warranty. D-Link DAP-3711 User Manual
  • D-Link DAP-3711 | Product Manual 1 - Page 8
    . 4 Signal Strength Signal strength indicator. A red light indicates a weak signal. Red and yellow together indicates a medium signal. Yellow, red and green together indicates a strong signal. D-Link DAP-3711 User Manual 8
  • D-Link DAP-3711 | Product Manual 1 - Page 9
    . The radiation pattern and wireless protocol of the DAP-3711 is designed for high-performance bridge connectivity. Using different models or models with mismatched firmware versions may cause problems, such as performance degradation or a reduction in coverage area. D-Link DAP-3711 User Manual 9
  • D-Link DAP-3711 | Product Manual 1 - Page 10
    to connect the LAN 2 port on the DAP-3711 to the management computer. 2. Ensure the computer is configured with the static IP address 192.168.0.2 and a subnet mask of 255.255.255.0. 3. Launch a web browser. Enter 192.168.0.50 in the address field of your browser. D-Link DAP-3711 User Manual 10
  • D-Link DAP-3711 | Product Manual 1 - Page 11
    instructions to configure the device in Access Point Mode. Configuring the Second DAP-3711 in Client Mode 1. Follow steps 1-4 of the instructions above the first DAP-3711's IP address (for instance, by changing it to 192.168.0.51, as in the following screenshot). D-Link DAP-3711 User Manual 11
  • D-Link DAP-3711 | Product Manual 1 - Page 12
    confirm that wireless connectivity between the two devices is configured correctly, navigate to the Status page and check the information under Associated Stations (shown below). D-Link DAP-3711 User Manual 12
  • D-Link DAP-3711 | Product Manual 1 - Page 13
    the number of walls and ceilings between the D-Link access point and other network devices to a minimum. Each wall or ceiling can reduce your adapter's range from 3-90 feet (1-30 meters). Position your devices so that the number of walls or ceilings is minimized. D-Link DAP-3711 User Manual 13
  • D-Link DAP-3711 | Product Manual 1 - Page 14
    2.4 Hz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone is not in use. D-Link DAP-3711 User Manual 14
  • D-Link DAP-3711 | Product Manual 1 - Page 15
    . Mounting on a Pole 1.Connect an Ethernet cable to the LAN port on the DAP-3711. 2.Place the DAP-3711 against the pole where you want it to be positioned. 3. Wrap the metal mounting ties around the pole and thread them through the holes on the DAP-37 D-Link DAP-3711 User Manual 15
  • D-Link DAP-3711 | Product Manual 1 - Page 16
    Access Point dlink WPA2-PSK 1234567890abc IP: 192.168.0.50 Subnet: 255.255.255.0 Gateway: 192.168.0.1 disable 802.11 ac auto 80 MHz disable D-Link DAP-3711 User Manual 16
  • D-Link DAP-3711 | Product Manual 1 - Page 17
    the DAP-3711 web interface, you will need to configure your computer's TCP/IP settings: 1. Right-click the Local Area Connection icon on your computer and click Properties, then click Continue. The Local Area Connection Properties dialog box will appear, as seen below. D-Link DAP-3711 User Manual
  • D-Link DAP-3711 | Product Manual 1 - Page 18
    : 3. In the above figure, the IP address should be set to 192.168.0.*. Here, * can be any number between 1-255 (but not 50, since the DAP-3711's default IP address is 192.168.0.50). D-Link DAP-3711 User Manual 18
  • D-Link DAP-3711 | Product Manual 1 - Page 19
    and click"Login"to login the main page of DAP-3711. As you can see, this management interface will enter the wizard mode to take you through the initial settings. Note: The password supports 4~31 digits of upper and lower case letters, numbers, and special symbols D-Link DAP-3711 User Manual 19
  • D-Link DAP-3711 | Product Manual 1 - Page 20
    Section 3 - Configuration Wizard When you log into the DAP-3711 for the first time, the Wizard page will automatic pop-up. You can also click Wizard in the top right corner. D-Link DAP-3711 User Manual 20
  • D-Link DAP-3711 | Product Manual 1 - Page 21
    Login Password If you log in to DAP-3711 for the first time, you need to change the password. The default password is admin. The device login password supports 4~31 digits of upper and lower case : within your local area network to assign an IP address automatically. D-Link DAP-3711 User Manual 21
  • D-Link DAP-3711 | Product Manual 1 - Page 22
    (WDS), Client (WDS)) you want to set the DAP-3711 to, and then follow the wizard's instructions to set it up step by step. Access The DAP-3711 connects directly to the main Point: Ethernet LAN and connect to the network. It means this device is a AP in WDS mode. D-Link DAP-3711 User Manual 22
  • D-Link DAP-3711 | Product Manual 1 - Page 23
    environment. Default 80 MHz in Access Point mode. DAP-3711 supports 10MHz/20MHz/40MHz/80MHz bandwidth. Frequency Indicates the channel setting for the DAP-3711. (Channel): In Access Point or Access Point ( to join the network without performing any security check. D-Link DAP-3711 User Manual 23
  • D-Link DAP-3711 | Product Manual 1 - Page 24
    is required. Key: Only 8 to 63 bits of upper and lower case English letters, numbers and special symbols are supported Complete After the data input is completed, press Next to complete the above setting procedure, and the device will automatically reboot. D-Link DAP-3711 User Manual 24
  • D-Link DAP-3711 | Product Manual 1 - Page 25
    to apply them. Wireless In the Wireless tab, you can configure the DAP-3711's Wi-Fi and radio settings. Wireless Toggle the button to enable or disable Wi-Fi. Settings: Radio Setting: In this section, users can set up basic and advanced Wi-Fi and radio settings. D-Link DAP-3711 User Manual 25
  • D-Link DAP-3711 | Product Manual 1 - Page 26
    channels which DAP-3711 can run. After clicking the Select, user can select the channels which DAP-3711 can run in their country. Transmit The device's output power. When the output Power: power is increased, the signal distance and signal strength will be improved. D-Link DAP-3711 User Manual 26
  • D-Link DAP-3711 | Product Manual 1 - Page 27
    MIMO: The DAP-3711 supports 2T2R Multi- DAP-3711 units. When TDMA is enabled, you can also decide whether you want to enable JTrans. JTrans can help prevent an internal wireless attack. The client and access point must be turned on at the same time when JTrans is enabled. D-Link DAP-3711 User Manual
  • D-Link DAP-3711 | Product Manual 1 - Page 28
    : Click this to select which SSID the DAP-3711 should connect to. Lock: Use this to select which SSID and MAC address the DAP-3711 should connect to. If you enable this, the DAP-3711 will only connect to the AP you specify. Cancel: Click this to cancel the scan. D-Link DAP-3711 User Manual 28
  • D-Link DAP-3711 | Product Manual 1 - Page 29
    : DAP-3711 is connected to the remote AP in it. When there are more than two APs with identical SSID and encryption in the environment, it will automatically connect to them. You can also check the connected AP information in the "Station List" on the "Status" page. D-Link DAP-3711 User Manual 29
  • D-Link DAP-3711 | Product Manual 1 - Page 30
    way to be adopted in large and middle enterprise as well as residential network. WPA2-PSK: As a new version of WPA, only all the clients support WPA2, can it be available. If it is selected, the data encryption can only be AES and the passphrase is required. D-Link DAP-3711 User Manual 30
  • D-Link DAP-3711 | Product Manual 1 - Page 31
    special symbols are supported Client When you enable this function, the clients which Isolation: are connected to the DAP-3711 will not be DAP-3711. MAC Filtering: Use this to set up a list of MAC addresses that you want to allow or disallow to connect to DAP-3711. D-Link DAP-3711 User Manual 31
  • D-Link DAP-3711 | Product Manual 1 - Page 32
    DAP3711 supports two LAN ports, in Route Mode, the LAN Interface here represents the LAN2 port. WAN Interface: In router mode, the physical LAN port becomes the WAN port. You need to enter the IP address or configure DHCP clients to get the IP address as well as PPPoE. D-Link DAP-3711 User Manual
  • D-Link DAP-3711 | Product Manual 1 - Page 33
    this to select the LAN port's speed negotiation Interface mode. Setting: IPv4/IPv6 Use this to add the Static Route rule for the DAPStatic Route: 3711. Interface After enabling this function, the two wired Isolation: interfaces of the device cannot ping each other D-Link DAP-3711 User Manual 33
  • D-Link DAP-3711 | Product Manual 1 - Page 34
    devices listed in IP Filter Default Settings and MAC Filter Settings. Policy: Deny: Deny the devices listed in IP Filter Settings and MAC Filter Settings. D-Link DAP-3711 User Manual 34
  • D-Link DAP-3711 | Product Manual 1 - Page 35
    Section 3 - Configuration IP Filter Click Add to add a new IP address to allow or deny. Settings: MAC Filter Click Add to add a new MAC address to accept or Settings: deny. D-Link DAP-3711 User Manual 35
  • D-Link DAP-3711 | Product Manual 1 - Page 36
    type. Time-sensitive data (like video/ audio data) can be assigned a higher priority than other data. For WMM to be enabled, the wireless client must support it as well. QoS Priority: Use this setting to set the QoS settings on the LAN port. D-Link DAP-3711 User Manual 36
  • D-Link DAP-3711 | Product Manual 1 - Page 37
    have registered themselves as visible to other devices. Time Restart: When this function is enabled, the DAP-3711 will automatically restart according to a schedule that you set. Reboot Period: There are three items can be selected: Every Day, Every Week, and Once. D-Link DAP-3711 User Manual 37
  • D-Link DAP-3711 | Product Manual 1 - Page 38
    will be saved to the Syslog Log Server server automatically. Settings: Ping The Ping Watchdog sets the DAP-3711 to Watchdog: continuously ping a user-defined IP address (for example, the IP address of the AP be able to re-enable it with modified parameters. D-Link DAP-3711 User Manual 38
  • D-Link DAP-3711 | Product Manual 1 - Page 39
    Section 3 - Configuration LED LED1, LED2, and LED3 light up to indicate the Configuration: DAP-3711's signal strength. The default ranges are: LED1: -95 dBm to -1 dBm LED2: -71 dBm to LED2 light; when the signal strength is higher than -56dBm, all the 3 LEDs light. D-Link DAP-3711 User Manual 39
  • D-Link DAP-3711 | Product Manual 1 - Page 40
    to restore the device to the Factory factory default settings. Settings: Reboot: Click the button to reboot the DAP-3711. Firmware Click the Browse button and choose a firmware Update: file, then click the Update button to upgrade the firmware to the latest version. D-Link DAP-3711 User Manual 40
  • D-Link DAP-3711 | Product Manual 1 - Page 41
    's password Account: Read-Only Use this to enable a Read Only guest account Account: Change Read- Use this to change the guest account's password Only Account: D-Link DAP-3711 User Manual 41
  • D-Link DAP-3711 | Product Manual 1 - Page 42
    the DAP-3711's network status Network Mode: This indicates whether the device is in Router Mode or Bridge Mode IP Protocol: This indicates whether the device is configured with a Static IP or DHCP Wired Port This displays the device's LAN MAC Address MAC Address: D-Link DAP-3711 User Manual 42
  • D-Link DAP-3711 | Product Manual 1 - Page 43
    noise floor value. In order to achieve the best results, a value of less than -95dBm is recommended Transmit Displays the DAP-3711's current Wi-Fi power Power: output Station This will list all of the client devices which are List Info: connected to the DAP-3711. D-Link DAP-3711 User Manual 43
  • D-Link DAP-3711 | Product Manual 1 - Page 44
    Section 3 - Configuration Statistics There are two subsections: Interface Statics and Throughput. Interface Displays the DAP-3711's traffic Statics: Throughput: Displays the current Ethernet and wireless traffic D-Link DAP-3711 User Manual 44
  • D-Link DAP-3711 | Product Manual 1 - Page 45
    Section 3 - Configuration Network In this tab, you can see the current IPv4 route table, APR table and bridge table. D-Link DAP-3711 User Manual 45
  • D-Link DAP-3711 | Product Manual 1 - Page 46
    Section 3 - Configuration Syslog Info This tab shows the current syslog. Click the Clear button to Clear the log. D-Link DAP-3711 User Manual 46
  • D-Link DAP-3711 | Product Manual 1 - Page 47
    to help you manage the device and your network. These tools include Ping IP, Traceroute, Link Test, Antenna Alignment and Spectrum Analyzer. Ping IP You can type in an IP address and check the ping result. IP Address: Enter the IP address that you would like to ping. D-Link DAP-3711 User Manual 47
  • D-Link DAP-3711 | Product Manual 1 - Page 48
    Section 3 - Configuration Traceroute This allows the user to traceroute an IP address. IP Address: Enter the IP address to traceroute D-Link DAP-3711 User Manual 48
  • D-Link DAP-3711 | Product Manual 1 - Page 49
    server IP address to check the speed between the two links. Iperf Type: Select Client or Server Iperf Dual: If you select Iperf Dual, the DAP-3711 will conduct a bi-directional speed test. Otherwise, it Iperf Interval: Enter the interval to wait between the tests. D-Link DAP-3711 User Manual 49
  • D-Link DAP-3711 | Product Manual 1 - Page 50
    Section 3 - Configuration Antenna Alignment When you select this, the DAP-3711 will recalibrate its signal strength. You can check which angle has the best antenna alignment when you install the DAP-3711. D-Link DAP-3711 User Manual 50
  • D-Link DAP-3711 | Product Manual 1 - Page 51
    Analyzer You can use the Spectrum Analyzer to scan for the best channels. When performing the scan, the DAP-3711 Wi-Fi may disconnect. Spectrum Enter the frequency range to conduct spectrum Analysis analysis on. It will take a few seconds to finish the Range: scan. D-Link DAP-3711 User Manual 51
  • D-Link DAP-3711 | Product Manual 1 - Page 52
    LEDs Power, WLAN, LAN, Signal strength Wireless Speed Up to 867 Mbps Antenna Type Directional Bandwidth Support 20/40/80 MHz Antenna Gain 15 dBi Beamwidth H: 40°, V: 15° Standards 802.11a rate. Environmental conditions will adversely affect wireless signal range. D-Link DAP-3711 User Manual 52
  • D-Link DAP-3711 | Product Manual 1 - Page 53
    Appendix A - Technical Specifications LAN Type Static, DHCP VLAN Support Yes Firewall IP / MAC filter Monitors Throughput, interfaces, routes table, bridge table, 0% to 90% Weight 600g (1.3 lbs) Dimensions 288 x 88 x 45 mm (11.3 x 3.4 x 1.8 in) Certifications CE FCC D-Link DAP-3711 User Manual 53
  • D-Link DAP-3711 | Product Manual 1 - Page 54
    of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of could void the user's authority to operate the equipment. D-Link DAP-3711 User Manual 54
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
User Manual
Version 1.00 | 25/12/2020
DAP-3711
5 km Long Range 802.11ac Wireless Bridge