D-Link DES-3326 Configuration Guide
D-Link DES-3326 Manual
 |
UPC - 790069255304
View all D-Link DES-3326 manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DES-3326 manual content summary:
- D-Link DES-3326 | Configuration Guide - Page 1
DES-3326 Layer 3 Switch Example Layer 3 Configuration Guide. Model: DES-3326 Firmware Version 1.00B19 OS Supported: Windows 95, Windows 98, Windows 98SE, Windows Me, Windows NT 4.0 and Windows 2000. Introduction This guide will help you to setup a routing function to operate between two TCPIP - D-Link DES-3326 | Configuration Guide - Page 2
, you will need to change the operating mode of the switch from layer 2 to layer 3. The default setting for the switch is layer 2. To do this, attach to the switch through its RS232 console port with HyperTerminal and login onto the switch. The default username and password is no username and no - D-Link DES-3326 | Configuration Guide - Page 3
return - return. You will be presented with the main menu options as shown in fig 3. Fig 3. Switch Main Menu Select from the main menu 'Switch Settings' Fig 4. Switch Settings Menu From the switch settings menu select 'Switch Operating Mode' - D-Link DES-3326 | Configuration Guide - Page 4
Operating Mode Using the space bar change the operating mode from layer 2 to 'IP Routing, support IEEE 802.1Q VLANs' as in fig 5. Apply the changes, the switch will reboot. Reattach to the switch through HyperTerminal. Please note, you do not need to change any of the configuration parameters in - D-Link DES-3326 | Configuration Guide - Page 5
7. Main Menu From the main menu select 'VLAN's' Fig 8. VLAN Menu Select 'Configure 802.1Q Port Settings'. You will need to configure the port VLAN ID (PVID) before configuring the 802.1Q VLAN's. The default PVID for all ports is set to 1. For setting up VLAN's for the engineering department use PVID - D-Link DES-3326 | Configuration Guide - Page 6
as used for the PVID previously. You will need to leave the default VLAN as is, ie do not change the default VID. Use the TAB key to cursor to the VID and enter '2', again use the TAB key to cursor to VLAN name and enter an appropriate name. In this example we have - D-Link DES-3326 | Configuration Guide - Page 7
E. You will need to Egress all the port members of this VLAN. In this example only ports 1 & 2 are members. In layer 3 routing configuration within the switch. From the main menu select layer 3 IP Networking, then select 'Setup IP Interface' Fig 11. Layer 3 IP Networking Fig 12. IP Interface Setup - D-Link DES-3326 | Configuration Guide - Page 8
we have used the fist octet for the interface name. The IP address is the IP address of the the switch in that particular subnet, we have choosen 192.168.0.250 MASK 255.255.255.0. The VID is the PVID set in the VLAN configuration previously done. After the config is applied, the screen - D-Link DES-3326 | Configuration Guide - Page 9
succesful, the layer configuration is complete. If the ping test produces a 'request timed out' check the configuration above more carefully. You may need to perform a factory reset and re-config the switch. ~ End of Document ~
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
 |
 |
DES-3326 Layer 3 Switch Example Layer 3
Configuration Guide.
Model:
DES-3326
Firmware Version
1.00B19
OS Supported:
Windows 95, Windows 98, Windows 98SE, Windows Me,
Windows NT 4.0 and Windows 2000.
Introduction
This guide will help you to setup a routing function to operate between two
TCPIP networks. Its important to have the latest firmware installed in the
switch before embarking on the configuration. At the time of writing this
document the firmware release was 1.00B19. Please visit the UK ftp site for
the latest firmware releases.
Network Configuration
Fig 1. Network Configuration.