D-Link DGS-3224SR Product Manual

D-Link DGS-3224SR Manual

Get D-Link DGS-3224SR PDF manuals and user guides View all D-Link DGS-3224SR manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DGS-3224SR manual content summary:

  • D-Link DGS-3224SR | Product Manual - Page 1
    D-Link ™ DGS-3224SR High-Density Stackable Gigabit Ethernet Switch User's Guide
  • D-Link DGS-3224SR | Product Manual - Page 2
    D-Link DGS-3212SR Stackable Gigabit Ethernet Switch Information in this document is subject to change without notice. © 2003 D-Link Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in
  • D-Link DGS-3224SR | Product Manual - Page 3
    CONTENTS D-Link ™ DGS-3224SR...i Intended Readers...vi Typographical Conventions ...vi Notes, Notices, and Cautions ...vii Safety Instructions...vii Safety Cautions ...vii General Precautions for Rack-Mountable Products ix Protecting Against Electrostatic Discharge ...x Introduction ...1 Switch
  • D-Link DGS-3224SR | Product Manual - Page 4
    37 Port Settings Configuration...41 Basic Port Configuration...41 Link Aggregation Configuration...44 Forwarding and Filtering...46 IGMP ...53 802.1w Rapid Spanning Tree ...53 QoS (Quality of Service)...58 Traffic Control (Broadcast/Multicast Storm Control 58 Configuring Default Priority
  • D-Link DGS-3224SR | Product Manual - Page 5
    SNMP Engine ID ...92 System Monitoring and Statistics...93 Port Utilization ...93 Packets ...94 Errors...97 Size...101 Maintenance ...107 Technical Specifications ...112 Glossary ...114 WARRANTY FOR ALL COUNTRIES AND REGIONS EXCEPT USA 121 WARRANTY INFORMATION FOR USA ONLY ...124
  • D-Link DGS-3224SR | Product Manual - Page 6
    Link DGS-3224SR Stackable Gigabit Ethernet Switch Intended Readers The DGS-3224SR User Guide contains information for setup and management and of the DGS-3224SR switch. This guide to prompts that must be typed exactly as printed in the manual. Indicates a window name. Names of keys on the keyboard
  • D-Link DGS-3224SR | Product Manual - Page 7
    D-Link DGS-3224SR Stackable Gigabit Ethernet Switch Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your device. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION
  • D-Link DGS-3224SR | Product Manual - Page 8
    D-Link DGS-3224SR gets wet, see the appropriate section in your troubleshooting guide or contact your trained service provider. • Do not push any objects into rated to operate with the power available in your location. Safety Instructions (continued) • Use only approved power cable(s). If you have
  • D-Link DGS-3224SR | Product Manual - Page 9
    Link DGS-3224SR system as well as to various peripherals or supporting hardware. CAUTION: Installing systems in a rack stabilizers for joined multiple racks before working on the rack. Safety Instructions (continued) Always load the rack from the bottom up, servicing other components in a rack. ix
  • D-Link DGS-3224SR | Product Manual - Page 10
    D-Link DGS-3224SR Stackable Gigabit Ethernet Switch NOTE: A qualified electrician must perform all connections to DC power and to safety grounds. All electrical wiring must comply with applicable
  • D-Link DGS-3224SR | Product Manual - Page 11
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 1 Introduction Switch Description Features Front-Panel Components Back Panel Description Plug-in Module Descriptions Management Options Switch Description The DGS-3224SR is a modular Gigabit Ethernet backbone switch designed for adaptability
  • D-Link DGS-3224SR | Product Manual - Page 12
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch • SysLog support • Simple Network Time Protocol • Web GUI Gigabit Ethernet port has a corresponding indicator. This will light steady green for a valid link and blink whenever there is reception or transmission (i.e. Activity--Act) of data occurring
  • D-Link DGS-3224SR | Product Manual - Page 13
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Rear Panel Description The rear panel of 1-2. Rear panel view of the Switch The AC power connector is a standard three-pronged connector that supports the power cord. Plug the female connector of the provided power cord into this socket, and the male
  • D-Link DGS-3224SR | Product Manual - Page 14
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Management Options The system may be SNMP-Based Management You can manage the switch with an SNMP-compatible console program. The switch is supports SNMP version 1.0, version 2.0 and version 3.0. The SNMP agent decodes the incoming SNMP messages and
  • D-Link DGS-3224SR | Product Manual - Page 15
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Installation Package Contents Before You Before you begin installing the switch, confirm that your package contains the following items: • One DGS-3224SR Layer 2 Gigabit Switch • Mounting kit: 2 mounting brackets and screws • Four rubber feet with
  • D-Link DGS-3224SR | Product Manual - Page 16
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Before You Connect to the Network NOTICE: Do Installing the Switch Without the Rack 1. Install the switch on a level surface that can safely support the weight of the switch and its attached cables. The switch must have adequate space for ventilation
  • D-Link DGS-3224SR | Product Manual - Page 17
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Installing the Switch in a Rack You can install the switch in most standard 19-inch (48.3-cm) racks. Refer to the
  • D-Link DGS-3224SR | Product Manual - Page 18
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Connecting Stacked Switch Groups Up to 12 Switches can be stacked . Please refer to the diagram below. Figure 2-4. Ring (Bus) Topology Please note that the DGS-3324SRi is needed to connect a group of Switches in the Star topology, as shown below. 5
  • D-Link DGS-3224SR | Product Manual - Page 19
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch DGS-3224SRi Figure 2-5. Star Topology Stacked Switch Group may connect to 2 or 1 Configuring a Switch Group for Stacking Follow the instructions below to configure the DGS-3224SR as the designated Master, and then to configure the slave units. To configure
  • D-Link DGS-3224SR | Product Manual - Page 20
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch DGS-3223Sr:4#config box_priority current_box_id 1 priority 1 Command: config box_priority current_box_id 1 priority 1 Success. DES-3224SR:4 DES-3224SR:4# To configure the same DGS-3224SR to function in a stacked group as the Slave, do the following:
  • D-Link DGS-3224SR | Product Manual - Page 21
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch External Redundant Power System The switch supports an external redundant power system. Figure 2-6. DPS-500 with DES-3224SR Figure 2-7. DPS-800 with DES-3224SR NOTE: See the DPS-500 documentation for more information. CAUTION: Do not use the switch
  • D-Link DGS-3224SR | Product Manual - Page 22
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Connecting the Console Port The switch provides Microsoft® Windows® 2000 operating system, ensure that you have Windows 2000 Service Pack 2 or later installed. Windows 2000 Service Pack 2 allows you to use arrow keys in HyperTerminal's VT100 emulation
  • D-Link DGS-3224SR | Product Manual - Page 23
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Password Protection The DGS-3224SR does not have a default user name and password. with the user name "newmanager". NOTE: Passwords are case sensitive. DGS-3224SR:4#create account admin newmanager Command: create account admin newmanager Enter a
  • D-Link DGS-3224SR | Product Manual - Page 24
    D-Link DGS-3224SR performance and detect potential problems in the switch, switch group or network. Managed devices that support SNMP include software ( the protocol used to access this information over the network. The DGS-3224SR supports the SNMP versions 1, 2c, and 3. You can specify which version
  • D-Link DGS-3224SR | Product Manual - Page 25
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch IP Address Assignment Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network
  • D-Link DGS-3224SR | Product Manual - Page 26
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Connecting Devices to the Switch After you assign IP addresses to the to connect a device to the connectors on the SFP transceiver. NOTICE: When the SFP transceiver acquires a link, the associated integrated 10/100/1000BASE-T port is disabled. 13
  • D-Link DGS-3224SR | Product Manual - Page 27
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 3 Introduction to Switch Management Login to Web Manager Web-based User Interface Basic Setup Switch Information IP Address User Accounts Saving Changes Factory Reset Restart System Introduction All software functions of the DGS-3224SR can be
  • D-Link DGS-3224SR | Product Manual - Page 28
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch This opens the management module's main page. display the hyperlinked menu buttons and subfolders contained within them. Click the D-Link logo to go to the D-Link website. Presents switch information based on your selection and the entry of configuration data.
  • D-Link DGS-3224SR | Product Manual - Page 29
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch NOTICE: Any changes made to the related information. Maintenance: contains menus for upgrading firmware and saving configuration files (TFTP Services), saving configuration changes, resetting and rebooting the switch, Ping test and logging out
  • D-Link DGS-3224SR | Product Manual - Page 30
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Switch Information Click the Switch Information link in the Configuration menu. Figure 3-3. Switch Information - Basic Settings The Switch Information window shows the switch's MAC Address (assigned by the factory and unchangeable). In
  • D-Link DGS-3224SR | Product Manual - Page 31
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Switch IP Settings Switch IP a subnet mask of 255.0.0.0 and a default gateway of 0.0.0.0. To manually assign the switch's IP address, subnet mask, and default gateway address: Select Manual from the Get IP From drop-down menu. Enter the appropriate IP
  • D-Link DGS-3224SR | Product Manual - Page 32
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch To use the BOOTP or DHCP protocols to assign the switch an IP address, subnet mask, and default gateway address: Use the Get IP From: pull-down menu to choose from BOOTP or DHCP. This selects how the switch will be assigned an IP address
  • D-Link DGS-3224SR | Product Manual - Page 33
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Setting the Switch's IP Address using the Console Interface Each Switch must be assigned its own IP Address, which is used
  • D-Link DGS-3224SR | Product Manual - Page 34
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch User Accounts Management Use the User Accounts Control Table to control user privileges. To view existing User Accounts, open the Security Management folder and click on the User Accounts link. This will open the User Account Management page, as
  • D-Link DGS-3224SR | Product Manual - Page 35
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Modify or delete an existing user account in the User Account Control Table - Edit. To delete the user account, click on
  • D-Link DGS-3224SR | Product Manual - Page 36
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch The switch has two levels of memory, normal the current configuration to non-volatile RAM before restarting the switch. Clicking the No option instructs the switch not to save the current configuration before restarting the switch. All of the
  • D-Link DGS-3224SR | Product Manual - Page 37
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Click the Restart button to restart the switch. Figure 3-11. Restart System NOTE: clicking Yes is equivalent to executing Save Changes
  • D-Link DGS-3224SR | Product Manual - Page 38
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 3-12. Switch Information The System Information page displays general information about the Switch including its MAC Address, Hardware Boot PROM
  • D-Link DGS-3224SR | Product Manual - Page 39
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Variables in the Advanced Settings menu of or Disabled here. GVRP Use this pull-down menu to Enable or Disable GVRP on the switch. Link Aggregation Algorithm The algorithm that the switch uses to balance the load across the ports that make up
  • D-Link DGS-3224SR | Product Manual - Page 40
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 4 Switch Stack Management The DGS-3224SR switch can be used as a standalone high-capacity switch or be used in a stacked arrangement. One stacking module can be installed to stack up to 4
  • D-Link DGS-3224SR | Product Manual - Page 41
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Priority - Displays the priority ID of the the front panel, under the STACK NO. heading. Alternatively, the stacking order can be manually assigned using the console's Command Line Interface (CLI). You can use the show stack_information command
  • D-Link DGS-3224SR | Product Manual - Page 42
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Use the following command to modify all box_id to become AUTO or static (apply current box id to User Set), use
  • D-Link DGS-3224SR | Product Manual - Page 43
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch 30
  • D-Link DGS-3224SR | Product Manual - Page 44
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 5 VLAN Configuration The first half of For a detailed list of CLI commands associated with VLAN management, please read the CLI reference guide. To create or modify an 802.1Q VLAN: In the Configuration folder, open the VLAN folder and click
  • D-Link DGS-3224SR | Product Manual - Page 45
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 5-3. 802.1Q Static VLANs Entry Settings - Modify The following fields can then be set in either the Add or Modify
  • D-Link DGS-3224SR | Product Manual - Page 46
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 5-4. GVRP Setting The following fields can be set: Parameter Description Unit Displays the Unit ID of the switch − within the
  • D-Link DGS-3224SR | Product Manual - Page 47
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Configure 802.1Q Static VLANs The following figures and tables describe how to set up static VLANs on the switch. Click on the Static VLAN Entry link in the VLANs folder to open the 802.1Q Static VLANs page, as shown below. Figure 5-5. 802.1Q Static
  • D-Link DGS-3224SR | Product Manual - Page 48
    Port Tag None Egress D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Corresponds to the ports that will be members of the VLAN. Specifies the port as either 802.1Q tagging or 802.
  • D-Link DGS-3224SR | Product Manual - Page 49
    None Egress D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Specifies the port as not being a static member of the VLAN, but with no restrictions for joining the VLAN dynamically through
  • D-Link DGS-3224SR | Product Manual - Page 50
    Ingress Check PVID GVRP D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch included in the Port- , and tagging decisions must be made. IEEE 802.1Q (tagged) VLANs are implemented on the DES-3224SR switch. 802.1Q VLANs require tagging, which enables the VLANs to span an entire network (assuming all
  • D-Link DGS-3224SR | Product Manual - Page 51
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch • Forwarding rules between ports - decides filter or are inserted after the MAC source address, but before the original EtherType/Length or Logical Link Control. Because the packet is now a bit longer than it was originally, the Cyclic Redundancy Check (
  • D-Link DGS-3224SR | Product Manual - Page 52
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 5-11. Adding an IEEE 802.1Q Tag Port VLAN ID Packets that are tagged (are carrying the 802.1Q VID
  • D-Link DGS-3224SR | Product Manual - Page 53
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch and forwarded by an untagging port will have no 802.1Q VLAN information. (Remember that the PVID is only used internally
  • D-Link DGS-3224SR | Product Manual - Page 54
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 6 Port Settings Configuration This port speed, duplex and learning state use the Port Configuration menu. Click the Port Configuration link in the Configuration folder: Figure 6-1. Port Configuration To configure switch ports: 1. Choose the
  • D-Link DGS-3224SR | Product Manual - Page 55
    Flow Control Learning D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Displays the flow control scheme used automatically listed in the forwarding table. When learning is Disabled, MAC addresses must be manually entered into the forwarding table. This is sometimes done for reasons of security or
  • D-Link DGS-3224SR | Product Manual - Page 56
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch NOTE: You cannot mirror a fast port onto a slower port. For example, if you try to mirror the traffic from a 100 Mbps port onto a 10 Mbps port, this can cause throughput problems. The port you are copying frames from should always support an equal or
  • D-Link DGS-3224SR | Product Manual - Page 57
    Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Link Aggregation Configuration Section 7 Link aggregation allows several ports to be grouped together and to act as a single link. This gives a bandwidth that is a multiple of a single link's bandwidth. Link aggregation is most commonly used to link
  • D-Link DGS-3224SR | Product Manual - Page 58
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 7-2. Link Aggregation Group Configuration The user-changeable parameters are as follows: Parameter Description Group ID Select an ID number for the group. Group Name Type in a
  • D-Link DGS-3224SR | Product Manual - Page 59
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Forwarding and Filtering Section 8 Static Unicast Forwarding Open the Forwarding & Filtering folder in the Configuration menu and click on the Unicast Forwarding link. This will open the Setup Static Unicast Forwarding Table, as shown below.
  • D-Link DGS-3224SR | Product Manual - Page 60
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 8-2. Setup Static Multicast Forwarding Table The Static Multicast Forwarding Settings page displays all of the entries made into the switch's
  • D-Link DGS-3224SR | Product Manual - Page 61
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch 48
  • D-Link DGS-3224SR | Product Manual - Page 62
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 9 IGMP Settings In order to use IGMP Snooping it must first be enabled for the entire Switch (see Advanced Settings). You may then fine-tune the settings for each VLAN using the IGMP Snooping link in the Configuration folder. When enabled for
  • D-Link DGS-3224SR | Product Manual - Page 63
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Parameter Description Query Interval Max Response Time Robustness Variable Last Member Query Interval The Query Interval field is used to set
  • D-Link DGS-3224SR | Product Manual - Page 64
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch A router port will be dynamically configured when IGMP query packets, RIPv2 multicast, DVMRP multicast, PIM-DM multicast packets are detected flowing into a port. Open the IGMP folder and the click on the Static Router Ports Entry link to open the
  • D-Link DGS-3224SR | Product Manual - Page 65
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch New IGMP Snooping Feature In the DGS-3224SR, the user may configure a forbidden portlist, whose members are not forced to become router ports. To activate this feature, please use the console (CLI). The
  • D-Link DGS-3224SR | Product Manual - Page 66
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Spanning Tree Protocol Configuration Section 10 The switch supports 802.1d Spanning Tree Protocol (STP) and 802.1w Rapid Spanning Tree Protocol (RSTP). 802.1d STP will be familiar to most networking professionals. However
  • D-Link DGS-3224SR | Product Manual - Page 67
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch learning states. An edge port loses its status if , all ports operating in full-duplex mode are considered to be P2P ports, unless manually overridden through configuration. 802.1d/802.1w Compatibility RSTP can interoperate with legacy equipment and
  • D-Link DGS-3224SR | Product Manual - Page 68
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Configure the following parameters and click the Apply button to implement them: Parameter Description Status This field can be toggled
  • D-Link DGS-3224SR | Product Manual - Page 69
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch STP Port Settings For stacked switch installations, first select the Unit to be configured. Figure 10-2. STP Port Settings In addition
  • D-Link DGS-3224SR | Product Manual - Page 70
    Link DGS-3224SR Layer 2 Gigabit Ethernet Switch The following fields can be set: Parameter Description Unit This is the Unit ID of a switch in a switch stack. 15 indicates a DGS- 3224SR Choosing Yes indicates a point-to-point (p2p) shared link. These are similar to edge ports however they are
  • D-Link DGS-3224SR | Product Manual - Page 71
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 11 QoS (Quality of Service) QoS settings allow customization of packet priority in order to facilitate delivery of data traffic that might be affected by latency problems. The IEEE 802.1p Priority specification uses 8 priority levels to
  • D-Link DGS-3224SR | Product Manual - Page 72
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch because a MAC address cannot be located in the of a default 802.1p priority to each port on the switch. Click on the 802.1p Default Priority link: Figure 10-4. Priority Based on a Port-group basis This page allows you to assign a default 802.1p
  • D-Link DGS-3224SR | Product Manual - Page 73
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Configuring 802.1p User Priority The DGS-3224SR allows the assignment of a User Priority to each of the 802.1p priorities. Figure 10-5. User Priority Configuration Once you have assigned a priority to the
  • D-Link DGS-3224SR | Product Manual - Page 74
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Scheduling Mechanism − This drop-down menu allows you to select between a Weight Fair and a Strict mechanism for emptying the priority queues.
  • D-Link DGS-3224SR | Product Manual - Page 75
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Traffic Segmentation Traffic segmentation is used to limit traffic flow from a single port to a group of ports on either a single switch (
  • D-Link DGS-3224SR | Product Manual - Page 76
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch This page allows you to determine which port on a given switch in a switch stack will be allowed to forward packets to other ports on that switch. Configuring traffic segmentation on the DGS-3224SR is accomplished in two parts. First you specify a
  • D-Link DGS-3224SR | Product Manual - Page 77
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch The following parameters can be set or are displayed: Parameter Description Unit Allows you to specify a switch in a switch stack using
  • D-Link DGS-3224SR | Product Manual - Page 78
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch System Log Server Section 12 The switch can send Syslog messages to up to four designated servers. Use the System Log
  • D-Link DGS-3224SR | Product Manual - Page 79
    UDP Port Status D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch designated are shown in the following: Bold font means the facility values that the switch currently now. Numerical Facility Code 0 kernel
  • D-Link DGS-3224SR | Product Manual - Page 80
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 13 Port Security Settings A given port's (or a range of ports') dynamic MAC address learning can be locked such that the
  • D-Link DGS-3224SR | Product Manual - Page 81
    Mode D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch This pull-down menu allows you to select how the MAC address table locking will be implemented on the switch, for the selected group of ports. The options are DeleteOnReset and DeleteOnTimeout. 68
  • D-Link DGS-3224SR | Product Manual - Page 82
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 14 SNTP Setting The Simple Network Time Protocol (SNTP) (an adaptation of the Network Time Protocol (NPT) is configured on
  • D-Link DGS-3224SR | Product Manual - Page 83
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Seconds Year Month Day Time in HH MM SS Enter the current year, if you want to update the system clock.
  • D-Link DGS-3224SR | Product Manual - Page 84
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Time Offset in Minutes constitute your local DST offset − 30, 60, 90, or 120 minutes. Time Zone Offset from GMT in +/
  • D-Link DGS-3224SR | Product Manual - Page 85
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 15 Access Profile Table configured Access Profiles on the switch, open the Configuration folder and click on the Access Profile Table link. This will open the Access Profile Table page, as shown below. Figure 16-1. Access Profile Table
  • D-Link DGS-3224SR | Product Manual - Page 86
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch The following parameters can be set: Parameter MAC Mask - Enter a MAC address mask for the destination MAC address. 802.1p Selecting this option instructs the switch to examine the 802.1p priority value of each packet header and use this as the,
  • D-Link DGS-3224SR | Product Manual - Page 87
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 16-3. Access Profile Configuration (IP) The IP Mask - Enter an IP address mask for the destination MAC address. Dscp Selecting this option instructs the switch to examine the DiffServ Code part of each packet header and use this as the, or
  • D-Link DGS-3224SR | Product Manual - Page 88
    Protocol Mode D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Selecting this option instructs the switch to examine the protocol type value in each frame's header. You must then specify what protocol(s) to include according to the following guidelines: Select ICMP to instruct the switch to
  • D-Link DGS-3224SR | Product Manual - Page 89
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 16 Security IP Management The Security IP Management page allows you to specify the IP addresses of management stations (PCs)
  • D-Link DGS-3224SR | Product Manual - Page 90
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Port Access Entity 802.1X Port-based Network Access Control The Switch is an implementation of the server side of IEEE
  • D-Link DGS-3224SR | Product Manual - Page 91
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 17-3. Typical 802.1X Configuration with User Authentication The user's information, including account number, password, and configuration details such as
  • D-Link DGS-3224SR | Product Manual - Page 92
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch State Machine Name Port Timers state machine Configuration folder, and then the Port Access Entity folder and finally click on the Configure Authenticator link. This will open the 802.1X Authenticator Settings page, as shown below. Figure 17-4. 802
  • D-Link DGS-3224SR | Product Manual - Page 93
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 17-5. 802.1X Authenticator Settings This window state, ignoring all attempts by the client to authenticate. The switch cannot provide authentication services to the client through the interface. The third option is auto. This enables 802.
  • D-Link DGS-3224SR | Product Manual - Page 94
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch • ReAuth [Disabled] - Determines whether regular reauthentication will take place on this port. The following parameters can be set: Parameter Description Unit
  • D-Link DGS-3224SR | Product Manual - Page 95
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Port Authenticating Settings To set the port authenticating settings, open the Configuration folder, and then the Port Access Entity folder, and then the PAE System Control folder. Finally click on the Port Authenticating Settings link. This will
  • D-Link DGS-3224SR | Product Manual - Page 96
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 17-7. 802.1X Authentic Radius Server Setting The following parameters can be set: Parameter Description Index Radius server settings index.
  • D-Link DGS-3224SR | Product Manual - Page 97
    V3 menus to select the SNMP version used for specific tasks. The DGS-3224SR supports the Simple Network Management Protocol (SNMP) versions 1, 2c, and the switch. Open the SNMP Manager folder and then the SNMP User Table link. Figure 18-1. SNMP User Table To delete an existing SNMP User Table entry
  • D-Link DGS-3224SR | Product Manual - Page 98
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch The following parameters are displayed: Parameter Description User Name An alphanumeric string of up to 32 characters. This is used to
  • D-Link DGS-3224SR | Product Manual - Page 99
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Group Name SNMP Version Auth-Protocol Priv-Protocol This name is used to specify the SNMP group created can request SNMP
  • D-Link DGS-3224SR | Product Manual - Page 100
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 18-5. SNMP View Table Configuration The SNMP Group created with this table maps SNMP users (identified in the SNMP User
  • D-Link DGS-3224SR | Product Manual - Page 101
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 18-6. SNMP Group Table To delete an existing SNMP Group Table entry, click the corresponding X icon under the Delete heading. To display the current settings for an existing SNMP Group Table entry, click the blue link for the entry under the
  • D-Link DGS-3224SR | Product Manual - Page 102
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 18-8. SNMP Group Table Configuration be used. SNMPv2 - Specifies that SNMP version 2c will be used. The SNMP v2c supports both centralized and distributed network management strategies. It includes improvements in the Structure of Management
  • D-Link DGS-3224SR | Product Manual - Page 103
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch SNMP Community Table Configuration Use this table to create an SNMP community string to define the relationship between the SNMP manager
  • D-Link DGS-3224SR | Product Manual - Page 104
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Open the Management folder, and then the SNMPV3 folder. Finally, click on the SNMP Host Table link. the current settings for an existing SNMP Group Table entry, click the blue link for the entry under the Host IP Address heading. Figure 18-10. SNMP
  • D-Link DGS-3224SR | Product Manual - Page 105
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch SNMP Engine ID The Engine ID is a unique To display the switch's SNMP Engine ID, open the SNMP Manager folder and click on the SNMP Engine ID link. This will open the SNMP Engine ID Configuration window, as shown below. Figure 18-12. SNMP Engine ID
  • D-Link DGS-3224SR | Product Manual - Page 106
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 18 System Monitoring and Statistics The DGS-3224SR provides extensive the port utilization, click on the Monitoring folder and then the Port Utilization link: Figure 19-1. Port Utilization Line Chart The following field can be set:
  • D-Link DGS-3224SR | Product Manual - Page 107
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Packets Received Packets Figure 19-2. Rx Packets Line Chart Select the desired switch using the Unit drop-down menu and the
  • D-Link DGS-3224SR | Product Manual - Page 108
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Received Unicast/Multicast/Broadcast Packets Figure 19-3. Rx Packets UMB Line Chart Select the desired switch using the Unit drop-down
  • D-Link DGS-3224SR | Product Manual - Page 109
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Transmitted Packets Select the desired switch using the Unit drop-down menu and the desired port using the Port drop-down
  • D-Link DGS-3224SR | Product Manual - Page 110
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Errors Transmitted Errors Figure 19-4. Transmitted Error Packets Line Chart Select the desired switch using the Unit drop-down menu and
  • D-Link DGS-3224SR | Product Manual - Page 111
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch LateColl (Late Collision) ExColl (Excessive Collision) SingColl (Single Collision) Coll (Collision) Late Collisions. The number of times that a collision is detected
  • D-Link DGS-3224SR | Product Manual - Page 112
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Received Errors Figure 19-5. Rx Error Packets Line Chart Select the desired switch using the Unit drop-down menu and the
  • D-Link DGS-3224SR | Product Manual - Page 113
    OverSize Fragment Jabber Drop D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch formed. The total number of frames received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and
  • D-Link DGS-3224SR | Product Manual - Page 114
    Size Packet Size D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 19-6. Packet Size Analysis Line Chart Select the desired switch using the Unit drop-down menu and the desired port
  • D-Link DGS-3224SR | Product Manual - Page 115
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Click View Table to see the same information in tabular form. 102
  • D-Link DGS-3224SR | Product Manual - Page 116
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch MAC Address Figure 19-7. MAC Address Table Select the desired switch using the Unit drop-down menu and the desired port
  • D-Link DGS-3224SR | Product Manual - Page 117
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Switch History Figure 19-8. Switch History 104
  • D-Link DGS-3224SR | Product Manual - Page 118
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch IGMP Snooping This allows the switch's IGMP Snooping table to be viewed. IGMP Snooping allows the switch to the multicast group. MAC Address The MAC address of the multicast group. Reports The total number of reports received for this group. 105
  • D-Link DGS-3224SR | Product Manual - Page 119
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Browse Router Port This displays which of the switch's ports are currently configured as router ports. A router port configured by a user (
  • D-Link DGS-3224SR | Product Manual - Page 120
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Section 19 Maintenance TFTP Services Trivial File Transfer Protocol (TFTP) services allow the switch firmware to be upgraded by transferring a new firmware file from a TFTP server to the switch. A configuration file can also be loaded into
  • D-Link DGS-3224SR | Product Manual - Page 121
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Click Start to initiate the file transfer. Upload Configuration To upload the switch settings to a TFTP server, click on the Maintenance folder and then the TFTP Service folder and then the Upload Configuration link: Figure 20-3. Save Settings to
  • D-Link DGS-3224SR | Product Manual - Page 122
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Figure 20-5. Ping Test The Infinite times checkbox, in the Number of Repetitions field, tells ping to keep sending data packets to the specified IP address until the program is stopped. Save Changes The DGS-3224SR has two levels of memory; normal RAM
  • D-Link DGS-3224SR | Product Manual - Page 123
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Reset gives the option of retaining the current configuration to non-volatile RAM before restarting the switch. Clicking the No click-box instructs the switch not to save the current configuration before restarting the switch. All of the
  • D-Link DGS-3224SR | Product Manual - Page 124
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Logout Use the Logout page to logout of the switch's Web-based management agent by clicking on the Log Out button. Figure 20-9. Logout 111
  • D-Link DGS-3224SR | Product Manual - Page 125
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Appendix A Technical Specifications General Standard Protocols Data Transfer Rates: IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit
  • D-Link DGS-3224SR | Product Manual - Page 126
    D-Link DGS-3224SR Layer 2 Gigabit Ethernet Switch Physical & Environmental AC inputs & External Redundant Power Supply 100 - 240 VAC, 50/60 Hz (internal universal power supply) Power Consumption: 90
  • D-Link DGS-3224SR | Product Manual - Page 127
    D-Link DGS-3212SR Layer 2 Gigabit Ethernet Switch Glossary 100BASE-FX 100Mbps Ethernet implementation for speed, duplex and flow control. When connected to an end station that also supports auto-negotiation, the link can self-detect its optimum operating setup. backbone port A port which does not
  • D-Link DGS-3224SR | Product Manual - Page 128
    D-Link DGS-3212SR Layer 2 Gigabit Ethernet Switch forwarding The process of sending a packet toward its destination by an internetworking device. full duplex A system that allows packets to be transmitted and received at the same time and, in effect, doubles the potential throughput of a link. half
  • D-Link DGS-3224SR | Product Manual - Page 129
    D-Link DGS-3212SR Layer 2 Gigabit Ethernet Switch switch A device which filters, forwards and layered set of communications protocols providing Telnet terminal emulation, FTP file transfer, and other services for communication among a wide range of computer equipment. Telnet A TCP/IP application
  • D-Link DGS-3224SR | Product Manual - Page 130
    -2-8899-1800 FAX: 61-2-8899-1868 TOLL FREE (Australia): 1300 766 868 TOLL FREE (New Zealand): 0800-900900 URL: www.dlink.com.au E-MAIL: [email protected] & [email protected] D-Link Brasil Ltda. Rua Tavares Cabral 102 - Conj. 31 e 33 05423-030 Pinheiros, Sao Paulo, Brasil TEL: (5511) 3094 2910 to
  • D-Link DGS-3224SR | Product Manual - Page 131
    REPAIR: 00800-7250-8000 & HELP: support.dlink.de URL: www.dlink.de & E-MAIL: [email protected] India D-Link India Plot No.5, Kurla -Bandra Complex 2652-8914/8476 URL: www.dlink.co.in E-MAIL: [email protected] & [email protected] Italy D-Link Mediterraneo Srl/D-Link Italia Via Nino Bonnet n. 6/B,
  • D-Link DGS-3224SR | Product Manual - Page 132
    United Arab Emirates TEL: (Jebel Ali): 971-4-883-4234 FAX: (Jebel Ali): 971-4-883-4394 & (Dubai): 971-4-335-2464 E-MAIL: [email protected] & [email protected] D-Link Europe (United Kingdom) Ltd 4th Floor, Merit House, Edgware Road, Colindale, London NW9 5AB United Kingdom TEL: 44-020-8731-5555
  • D-Link DGS-3224SR | Product Manual - Page 133
    120
  • D-Link DGS-3224SR | Product Manual - Page 134
    WARRANTY FOR ALL COUNTRIES AND REGIONS EXCEPT USA Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder
  • D-Link DGS-3224SR | Product Manual - Page 135
    digung hervorrufen. 17. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren Servicepartner. Somit stellen Sie die THIS LIMITATION WILL APPLY EVEN IF DLINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME
  • D-Link DGS-3224SR | Product Manual - Page 136
    in addition mailing or shipping costs. Software: Warranty service for software products may be obtained by contacting a D-Link office within the applicable warranty period. A list of D-Link offices is provided at the back of this manual. D-Link warrants that its software products will perform in
  • D-Link DGS-3224SR | Product Manual - Page 137
    Link D-Link Link's applicable product documentation as being compatible. D-Link software. D-Link makes no the scope of D-Link's applicable product product from: D-Link or its authorized Link warrants that the hardware portion of the D-Link spare kits Ninety (90) days D-Link's sole obligation shall be to
  • D-Link DGS-3224SR | Product Manual - Page 138
    through the inventory clearance or liquidation sale or other sales in which DLink, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining before the end of the Warranty Period to an Authorized D-Link Service Office. The customer must submit as part of the claim
  • D-Link DGS-3224SR | Product Manual - Page 139
    on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the Product and to the product. Repair by anyone other than D-Link or an Authorized D-Link Service Office will void this Warranty. Disclaimer of Other
  • D-Link DGS-3224SR | Product Manual - Page 140
    CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
D-Link ™ DGS-3224SR
High-Density Stackable Gigabit Ethernet Switch
User’s Guide