D-Link DGS-6600-48T Hardware Installation Guide

D-Link DGS-6600-48T Manual

D-Link DGS-6600-48T manual content summary:

  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 1
    Hardware Installation Guide Product Model : DGS-6600 Series Layer 3 Chassis Ethernet Managed Switch 6 7 8 Release 3.0
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 2
    -6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Information in this document is subject to change without frequency energy, and, if not installed and used in accordance with this manual, may cause harmful interference to radio communications. Operation of this equipment in
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 3
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Intended Readers...vii Typographical Conventions...vii Notes, Notices, and Cautions...ix Safety Suggestions ...ix Safety Recommendations for Handling the Switch ix Safety Recommendations for Removing
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 4
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Simple Installation Steps...40 Mounting the DGS-6600 Series Switch into the Cabinet 40 Fan Tray Installation...41 Power Supply Installation...43 Air Filter Installation...
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 5
    Hardware Installation Guide DGS-6600 Series Switch Monitoring Function 71 Maintaining the DGS-6600 Series Switch Hardware 71 Maintaining the DGS-6600 Modules ...71 Maintaining the Ventilation System...71 Maintaining the Power Supply ...72 Remote Maintenance ...72 Chapter 7 Troubleshooting 73
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 6
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Intended Readers The DGS-6600 Series Switch Hardware Installation Guide contains information on how to install the Switch hardware. This manual is intended for network or I.T. managers familiar with network management
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 7
    Series products are encapsulated and must be replaced only by qualified Service personnel. Contact your qualified Service personnel for product replacement. Do not attempt to replace the battery. If these instructions are disregarded and replacement of these batteries is attempted, the following
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 8
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide • Replace with the same or equivalent battery type as recommended by the battery manufacturer. • Dispose of the battery in accordance with the battery manufacturers recommendation.
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 9
    6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide • Avoid carrying out maintenance on the equipment alone and neutral (AC) conductors are connected. • Disconnect all power supply cords before servicing. • Connect the power cable to a circuit breaker rated not greater than 20A.
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 10
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Grounding requirements Proper grounding of the switch will help ensure stable and reliable operation of the DGS-6600 series switch. it is important to verify
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 11
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Laser Safety A number of the optical modules included in the DGS-6600 series switches are Class I laser products. Therefore, when using these products pay careful
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 12
    Managed Switch Hardware Installation Guide Chapter 1 Introduction DGS- -Swappable Line Cards, Fan Tray, and Power Supplies The DGS-6604 supports the hot-swapping of line cards, the fan tray, and power management, route management, and providing network services. The line card modules are capable of
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 13
    Hardware Installation Guide The DGS-6604 includes several features that ensure physical resilience, including multiple redundant power supplies and the capability of hot-swapping line cards or modules in the event of a fault. • Secure Switch Management Methods The DGS-6604 supports several features
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 14
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6604 Product Appearance Figure 1-1 DGS-6604 Product Appearance Number 1 2 3 4 Item Name Description Power Layer The built-in power shelf can host up to four
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 15
    6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6604 Hardware Composition The DGS-6604 hardware The other three slots can be used to connect to various line cards. All the modules supported by the DGS-6604 are of the same height, width and depth. The dimensions of
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 16
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6604 Ventilation/Heat Dissipation System The DGS requirements. • Hot-Swappable Line Cards, Fan Tray, and Power Supplies The DGS-6608 supports the hot-swapping of line cards, the fan tray, and power supplies to minimize disruption
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 17
    Ethernet Managed Switch Hardware Installation Guide • Efficient Data Processing Design , route management, and providing network services. The line card modules are capable to a specific group of source IP addresses. • Support for 802.1X The DGS-6608 supports 802.1X. 802.1X is a mechanism that is
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 18
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6608 Product Appearance Figure 1-3 DGS-6608 Product Appearance Number 1 2 3 4 Item Name Description Power Layer The built-in power shelf can host up to eight
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 19
    -6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6608 Hardware Composition The DGS-6608 hardware consists frame of the DGS-6608 consists of the module slots and the backplane. The DGS-6608 supports eight module slots. The slots 4 and 5 of the Switch can only be used for
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 20
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6608 Ventilation/Heat Dissipation System The DGS-6608 operates at a temperature of 0-50ºC. The hardware of the DGS-6608 has been thermally designed so
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 21
    Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600 CPU & I/O Modules The DGS-6604/6608 supports the modules described below: DGS- -II is a CPU module for the DGS-6604/6608, the DGS-6608 is able to support 2 x CM. DGS-6600-24SC2XS: This module includes 12 SFP ports, 12 combo ports
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 22
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-CM Module The basic appearance of the DGS-6600-CM management module is shown in Figure 1-5. The DGS-6600-CM management module is
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 23
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide LEDs The DGS-6600-CM uses different colored LEDs to indicate different systems status, as described in Table 1-3. LED Indicator Power System CPU Utilization Master
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 24
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Technical Specifications Item Description Standard Compliance Management Mode Management port supports IEEE802.3, IEEE802.3u, IEEE802.3ab Half/Full-duplex support CLI Telnet Web-based Port Type 1x Female DCE RS-232
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 25
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-CM-II management module: The basic appearance of the DGS-6600-CM-II management module is shown in Figure 1-6. The DGS-6600-CMII
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 26
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide LEDs The DGS-6600-CM-II uses different colored LEDs to indicate different systems status, as described in Table 1-5. LED Indicator Power System CPU Utilization
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 27
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Technical Specifications Item Description Standard Compliance Management Mode Management port supports IEEE802.3, IEEE802.3u, IEEE802.3ab Half/Full-duplex support CLI Telnet Web-based Port Type 1x Female DCE RS-232
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 28
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-24SC2XS Module The basic appearance of 2 SFP+ ports, please note that the DGS-6600-24SC2XS last two SFP+ ports do not support DEM-310GT/311GT/312GT2/ 314GT/315GT/330T/R/331T/R/210/211/220/T/R or DGS-712 transceiver. LEDs
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 29
    3 Chassis Ethernet Managed Switch Hardware Installation Guide Technical Specifications Item Compliance Standard Compliance IEEE 802.3 IEEE 802.3ab IEEE 802.3ae IEEE 802.3aq IEEE 802.3u IEEE 802.3z Full-duplex support/Half-duplex support (IEEE 802.3x Flow Control support for Full-Duplex mode) SFF
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 30
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-16XS-D The basic appearance of the DGS-6600-16XS-D module is shown in Figure 1-8. The DGS-6600-16XS-D is a line card module of
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 31
    3 Chassis Ethernet Managed Switch Hardware Installation Guide Technical Specifications Item Compliance Standard Compliance IEEE 802.3 IEEE 802.3ab IEEE 802.3ae IEEE 802.3aq IEEE 802.3u IEEE 802.3z Full-duplex support/Half-duplex support (IEEE 802.3x Flow Control support for Full-Duplex mode) SFF
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 32
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-48P Module The basic appearance of the DGS-6600-48P module is shown in Figure 1-9. The DGS-6600-48P is a line card module
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 33
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide LEDs The DGS-6600-48P uses different colored LEDs to indicate different systems status, as described in Table 1-11. LED Indicator Power System Color and
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 34
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Technical Specifications Item Compliance Standard Compliance Port Type LED IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af, Half/full-duplex support 48x 10/100/1000 Mbps PoE ports Power System PoE Hot Swap Ability
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 35
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-48S Module The basic appearance of the DGS-6600-48S module is shown in Figure 1-10. The DGS-6600-48S is a line card
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 36
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Technical Specifications Item Compliance Standard Compliance Port Type LED IEEE 802.3z Full-duplex support 48x SFP modules Power System Hot Swap Ability Supported Power 118.6 Watts Consumption EMC Safety Regulation MTBF
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 37
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-48T Module The basic appearance of the DGS-6600-48T module is shown in Figure 1-11. The DGS-6600-48T is a line card
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 38
    Managed Switch Hardware Installation Guide Technical Specifications Item Compliance Standard Compliance Port Type LED IEEE 802.3, IEEE 802.3u, IEEE 802.3ab Half/Full-duplex Support 48x 10/100/1000 Mbps RJ-45 ports Power System Hot Swap Ability Supported Power 109.8 Watts Consumption
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 39
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-48TS Module The basic appearance of the DGS-6600-48TS module is in Figure 1-12. The DGS-6600-48TS is a line card module
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 40
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide LEDs The DGS-6600-48TS uses different colored LEDs to indicate different systems status, as described in Table 117. LED Indicator Power System 10/100/
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 41
    6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Technical Specifications Item Compliance Standard Compliance Port Type LED IEEE: 802.3, 802.3u, 802.3ab, 802.3z, 802.3x flow control support for full-duplex mode Half/full-duplex support 24x 10/100/1000 Mbps ports, 24x SFP
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 42
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide DGS-6600-8XG Module The basic appearance of the DGS-6600-8XG module is shown in Figure 1-13. The DGS-6600-8XG is a line card
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 43
    Ethernet Managed Switch Hardware Installation Guide Technical Specifications Item Compliance Standard Compliance Port Type LED IEEE 802.3ae, Full-duplex support XFP MSA compliant transceiver support 8x 10G XFP modules Power System Hot Swap Ability Supported Power 200.26 Watts Consumption
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 44
    3 Chassis Ethernet Managed Switch Hardware Installation Guide Chapter 2 Installation Installation Site Requirements System heat dissipation system. • Ensure that the cabinet is both stable and strong enough to support the weight of the DGS-6604 or DGS-6608 chassis and its installed components. •
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 45
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Ventilation Requirements Figure 2-1 shows the ventilation requirements of the DGS-6604 and Figure 2-2 shows the vent alation requirements of the DGS-6608. To ensure normal
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 46
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Power Requirements When an AC power supply is install the same types of redundant power supply units, using different power supplies is not supported by the Switch. The DGS-6600 Series Switch requires a good grounding system to
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 47
    3 Chassis Ethernet Managed Switch Hardware Installation Guide lightning discharge ground is only used by the most often affected by conductive interference. A filter can be used to control interference problems. However, signal paths in the equipment may be affected by radiated interference, making
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 48
    Chassis Ethernet Managed Switch Hardware Installation Guide 4. Take appropriate measures to isolate be plugged into the SFP ports of the DGS-6600 series Modules supporting SFP ports. Installation Tool Requirements The tools needed to install the ) • Fan Tray • Air Filter • CD software and manual 37
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 49
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide • QIG Installation Flowchart Verifying the Installation When planning the DGS-6600 Series installation, please consider the following points: the installation location, the mode of networking
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 50
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide • Does the intended installation location have a power supply that meets the Switch requirements and does the intended location have the appropriate rated AC requirements. • The
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 51
    3 Chassis Ethernet Managed Switch Hardware Installation Guide Simple Installation Steps 1. Before instillation of Switch, move the Switch to the appropriate position in the rack. 3. With one person supporting the Switch, the other should fasten the screws into all the available bracket holes. The
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 52
    is used by the DGS-6600 Series Switch as a ventilation system. Follow the instructions below to correctly install the fan tray: 1. Use the thumb-screws to remove the fan tray blank panel. 2. Insert the fan tray into the guide rail of the fan tray slot. 3. Secure the fan tray by tightening the
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 53
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Figure 2-5 Schematic diagram for installing the fan tray in the DGS-6608 42
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 54
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Power Supply Installation The procedure for installing the AC power supply is shown in the diagram 2-4: Figure 2-6 Schematic diagram for installing an AC power supply
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 55
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Air Filter Installation On the back of the chassis on the edge of the right-side is a vertical slot where the air filter can be
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 56
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide System Ground Connection The back of the DGS-6604 has two working ground connections on its back panel. The grounds must be well treated to
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 57
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Connecting the AC Power Supply to the Power Module Use the AC power cable to connect to the AC power module panel, as indicated in
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 58
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Connecting the Management Module Cable Simple Management Module Cable Connection Steps 1. Connect the RJ45 connector of the Ethernet cable to the Ethernet port of the
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 59
    to install boards in the DGS-6600 Series Switch: 1. Remove the component card or blank panel as instructed in the section Removing Line Cards from the DGS-6600. 2. Insert the new board into the guide rail of the vacant slot. 3. Use the levers on the left and right hand side to push
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 60
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Figure 2-12 Schematic diagram for installing a line card 49
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 61
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Connecting the External Interface Cables Connecting External Interface optic cables too tightly may break the glass inside and cause transmission problems. Binding twisted-pair cables too tightly may negatively impact the twisted-
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 62
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Installation Checks Checking the Cabinet • Ensure that the external power supply corresponds with cabinet's distribution panel. • Check that the cabinet door can close properly after
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 63
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Chapter 3 Connecting the Switch Switch to End Node Chassis to Switch Connecting To Network Backbone or Server Connecting the Management Module Cable Connecting the External
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 64
    -6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Chassis to Switch There is a great deal of port to the Switch via a twisted pair Category 5e UTP/STP cable. "Connect switch supporting a fiber-optic uplink to the Switch's SFP ports via fiber-optic cabling. See cabling
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 65
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Connecting To Network Backbone or Server The combo SFP ports and the 1000BASE-T ports are ideal for uplinking to a network backbone, server or server farm.
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 66
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Connecting the Management Module Cable Refer to Connecting fiber-optic cables too tightly may break the glass inside and cause transmission problems. Binding twisted-pair cables too tightly may negatively impact the twisted-pair
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 67
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Chapter 4 Introduction to Switch Management Management Options The Switch can be managed with an SNMP-compatible console program. The Switch supports SNMP version 1.0, version 2.0 and version 3.0. The SNMP agent decodes the incoming
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 68
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Command Line Interface through the Serial Ports Users can also connect a computer or terminal to one of the serial console ports (USB or RS-232)
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 69
    Guide • Select Terminal keys for Function, Arrow and Ctrl keys. Make sure to use Terminal keys (not Windows keys) are selected. NOTE: When using HyperTerminal with the Microsoft® Windows® 2000 operating system, ensure that Windows 2000 Service CLI Manual program. If problems occur while making
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 70
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide enter a user name and a password. Upon the initial connection, there is no user name or password and therefore just press enter twice to access the
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 71
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide First Time Connecting to the Switch The Switch supports user-based security that provides prevention of unauthorized access to the Switch or change of settings. This section explains how to log onto the Switch
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 72
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Connecting to the Ethernet Management Port The front panel of the CM Module features an out-of-band Ethernet Management port. The port is an
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 73
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide The Switch CM is assigned a unique MAC -level account for the Switch, do the following: Creating User Accounts The Switch supports user accounts with different access levels. The following access levels can be assigned to
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 74
    6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide When creating a user account, the user can proper operation, monitor performance and detect potential problems in the Switch, switch group or network. Managed devices that support SNMP include software (referred to as an agent
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 75
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide SNMP v.3 uses a more sophisticated authentication process management software. In addition to the standard MIB-II, the Switch also supports its own proprietary enterprise MIB as an extended Management Information Base. The
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 76
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Chapter 5 Web-based Switch Management Introduction Enabling and Configuring the Web User Interface Logging onto the Web Manager Web-based User Interface (Web UI) Configuring
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 77
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Enabling and Configuring the Web User Interface To re to be 8000: DGS-6600:2>enable DGS-6600:15#configure terminal DGS-6600:15(config)#ip http service-port 8000 DGS-6600:15(config)#end DGS-6600:15# Display the Web UI settings as
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 78
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Logging onto the Web Manager To begin managing the Switch, simply run the browser installed on your computer. Use the IP address you have defined
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 79
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Areas of the User Interface Figure 5-2 shows the user interface. 6 areas divide the user interface and are described in the table 5-1. Area Green Light Blue
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 80
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Configuring the Management Interface using the Web UI 1. In the folder window expand the Configuration folder by clicking on the Plus (+) symbol to the left. 2.
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 81
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Chapter 6 Maintenance DGS-6600 Series Switch Monitoring Function Maintaining the DGS-6600 Series Switch Hardware Remote Maintenance 70
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 82
    . • The operating status of the power supplies and fan tray. • The Switch's temperature. Please see the DGS-6604 Command Line Interface Guide and the Configuration Guide for more information on the commands that are used for monitoring the DGS-6604. Maintaining the DGS-6600 Series Switch Hardware
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 83
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Maintaining the Power Supply Carry out the following vacant power supply slot. 5. Reconnect the power cables. Remote Maintenance Remote maintenance is supported by the DGS-6604. When installation of the Switch is complete, the user
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 84
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Chapter 7 Troubleshooting General Flow Chart for Troubleshooting Installation Faults Common Troubleshooting Procedures General Flow Chart for Troubleshooting Installation Faults 73
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 85
    configure the Switch. Troubleshooting: To resolve this issue please contact the D-Link Customer Service Department for technical support. Fault 2: The and check if the guiding rails for the slot have become distorted. If there is a problem with the backplane's slot or the guiding rails have become
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 86
    check if the guiding rails for the slot have become distorted. If there is a problem with the backplane's slot or the if the guiding rails have time. For example, the Status LED is flashing or turned off. Troubleshooting: Check if the management module has become loose. If the management module
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 87
    , please contact the D-Link Customer Service Department for technical support. Fault 8: Illegible characters appear in the serial port console. Description: Illegible characters appear in the serial port console. Troubleshooting: These kinds of problems usually relate to the serial port's settings
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 88
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Appendix A Technical Specifications Technical Specifications 6604 Module slots Number of supported VLANs Layer 2 protocols Layer 3 protocols Management mode Other protocols Control Module I/O Module Fan Tray Hot-swap
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 89
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide EMC Safety Regulations Operating Temperature Storage Temperature Operating Humidity Environment EMC (Class A): • FCC Part 15 • CSA C108.8 • 89/336/EEC • EN 55022 • EN 61000-3-2 • EN
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 90
    Ethernet Managed Switch Hardware Installation Guide Power Supply Power Supply Redundancy Fan Power Supply / Fan Rated voltage : 110 VAC 220 VAC Tolerance range : 90~264 VAC Power consumption: 853.5 W/set Heat Dissipation: 2912.4 BTU/hr@110V 2912.4 BTU/hr@220V Supported - all power supplies must be
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 91
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide I/O Module Fan Tray Hot-swap ability DGS-6600-48T, DGS-6600-48S, DGS-6600-48TS, DGS-6600-48P, DGS6600-16XS-D DGS-6600-FAN-II Supported on all cards 80
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 92
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide EMC Safety Regulations Operating Temperature Storage Temperature Operating Humidity Environment EMC (Class A): • FCC Part 15 • CSA C108.8 • 89/336/EEC • EN 55022 • EN 61000-3-2 • EN
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 93
    Ethernet Managed Switch Hardware Installation Guide Power Supply Power Supply Redundancy Fan Power Supply / Fan Rated voltage : 110 VAC 220 VAC Tolerance range : 90~264 VAC Power consumption: 853.5 W/set Heat Dissipation: 2912.4 BTU/hr@110V 2912.4 BTU/hr@220V Supported - all power supplies must be
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 94
    Chassis Ethernet Managed Switch Hardware Installation Guide Connection Modules The DGS-6600 series switch supports several types of SFP and XFP modules -mode 2KM 100 Base-FX Single-mode 15KM Table A-1 Supported SFP Module Technical Specifications XFP Module Models and Technical Specifications
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 95
    Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Appendix B Connectors and Connection Media 1000BASE-T/100BASE of the 1000BASE-T speed rate, the user needs to use CAT5e or higher cabling, which supports a maximum length of 100M. The 1000-BASE-T speed rate complies with IEEE 802.3ab
  • D-Link DGS-6600-48T | Hardware Installation Guide - Page 96
    DGS-6600 Layer 3 Chassis Ethernet Managed Switch Hardware Installation Guide Figure B-1 Straight-Through Vs Crossover Schematic Diagram for the four twisted pair required for 10BASE-T/100BASE-TX Optical Fiber Connection If using fiber-optic ports,
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96

Hardware Installation Guide
Product Model : DGS-6600 Series
Layer 3 Chassis Ethernet Managed Switch
Release 3.0