D-Link DI-707 Quick Installation Guide

D-Link DI-707 Manual

Get D-Link DI-707 PDF manuals and user guides
UPC - 790069241000
View all D-Link DI-707 manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DI-707 manual content summary:

  • D-Link DI-707 | Quick Installation Guide - Page 1
    D-Link DI-707 Quick Installation Guide 1. Hardware Installation A. Setup LAN connection: connect an Ethernet cable (provided) from your computer's Ethernet port to one of the LAN ports on the DI-707. B. Find and Double Click the Network Icon B. Power on: connect the power cord to a power outlet and
  • D-Link DI-707 | Quick Installation Guide - Page 2
    your computer name on a sheet of paper. E. Click the Configuration Tab. It should list your network (Ethernet) adapter and the loaded network protocols and services. Find TCP/IP for the network adapter connected to your Cable/DSL modem. F. Find and double click the TCP/IP setting for your Network
  • D-Link DI-707 | Quick Installation Guide - Page 3
    on your computer, you probably are not. The safest way to check is to call your provider, or read the documentation provided with your Internet service to determine if you currently use PPPoE. If you are using PPPoE, begin Step 5. If you are not using PPPoE, proceed below. H. Write down whether
  • D-Link DI-707 | Quick Installation Guide - Page 4
    DNS Server addresses There are normally two, but only one is needed. In step 4 all of this information will be required to configure the DI-707 with your provider. 3. Reconfigure your TCP/IP settings A. Click the IP Address tab. Select Obtain an IP address automatically. K. Find and write down
  • D-Link DI-707 | Quick Installation Guide - Page 5
    of the items are set, press the Save button and reboot the DI-707. You have now configured the DI-707. Refer to the User manual to review features and operation instructions that you may need for your use. 5. Configure the DI-707 with PPPoE A. Click the IP Address tab. Select Obtain an IP address
  • D-Link DI-707 | Quick Installation Guide - Page 6
    . Type the DI-707's IP address (default is: http://192.168.0.1) in the Location (for Netscape) or Address (for IE) field and press ENTER. F. Key in the system password (the factory default setting is "admin") in the System Password field and click on the Log in button. G. Press the Setup button and
  • D-Link DI-707 | Quick Installation Guide - Page 7
    After all of the items are set, press the Save button and reboot the DI-707. You have now configured the DI-707. Refer to the User manual to review features and operation instructions that you may need for your use. Rev: 10102000
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
Rev: 10102000
D-Link
DI-707 Quick Installation Guide
1. Hardware Installation
A.
Setup LAN connection:
connect
an Ethernet cable (provided) from your computer’s
Ethernet port to one of the LAN ports on the DI-707.
B.
Power on:
connect the power cord to a power outlet and turn the power switch on. The
DI-707 will automatically enter the self-test phase. When in the self-test phase, the
indicators M1 and M2 will be lit for about 5 seconds, and then M1 and M2 will flash
three times to indicate that the self-test operation has finished. Finally, the M1 will
flash continuously once per second to indicate that the DI-707 is in normal operation.
C.
Setup WAN connection:
connect
the network
cable from your cable or DSL modem
to the WAN port of the DI-707. If you don’t see a link light on the WAN LED after
everything is connected and turned on, try the network cable provided with the DI-707.
2. Find and Write Down Your Computer's Internet Settings
A.
Open the Control Panel
B.
Find and Double Click the Network Icon
C.
Click the Identification Tab