D-Link DVG-1120S Manual

D-Link DVG-1120S - VoIP Gateway/Router With 1 LAN Port Manual

Get D-Link DVG-1120S - VoIP Gateway/Router With 1 LAN Port PDF manuals and user guides
UPC - 790069266249
View all D-Link DVG-1120S manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DVG-1120S manual content summary:

  • D-Link DVG-1120S | Manual - Page 1
    D-Link DVG-1120S VoIP Residential Gateway with Two Voice Ports Manual Building Networks for People
  • D-Link DVG-1120S | Manual - Page 2
    3 Introduction 4 Connections 5 Features and Benefits 6 LEDs ...7 Web-based Management 8 Configuration Using a Console 35 Using the Console Port 40 Command Line Interface 46 Networking Basics 54 Technical Specifications 69 Contacting Technical Support 72 Warranty 73 Registration 76 2
  • D-Link DVG-1120S | Manual - Page 3
    Package Contents Contents of Package: D-Link DVG-1120S VoIP Residential Gateway with Two Voice Ports A/C Power Adapter Manual on CD Quick Installation Guide Note: Using a power supply with a different voltage rating than the one included with the DVG-1120S will cause damage and void the warranty for
  • D-Link DVG-1120S | Manual - Page 4
    IP addresses for LAN users, allowing multiple users to share a single Internet connection. You can configure and monitor the DVG1120S via the Console or the Web browser. Telnet and SNMP management is also supported. By routing calls over the Internet or any IP network, the DVG-1120S can reduce or
  • D-Link DVG-1120S | Manual - Page 5
    is in the up position, Phone1/2 will be configured to PSTN Mode. Ethernet WAN A 10Mbps Ethernet port fitted with an RJ-45 connector used to connect the VoIP gateway to a WAN device (e.g. Cable/ADSL Modem). This port accepts Category 3, 4 or 5 UTP cabling with an RJ-45 connector. Ethernet LAN A 10
  • D-Link DVG-1120S | Manual - Page 6
    configuration IP Routing support (RIP1, RIP2 and Static Routing) Remote software download/update Supports IP sharing to allow multiple users to access the Internet via a single IP address Built-in PPPoE function to support dial-up connection for broadband technology Supports Caller ID Supports
  • D-Link DVG-1120S | Manual - Page 7
    (usually a Cable or ADSL Modem). When a good link to a powered-up but idle device is detected on a port, the WAN indicator shines steadily. When packets are received from the device, the indicator blinks off and on. VoIP Gateway Power Status Alarm WAN Ethernet Phone1 Phone2 DVG-1D1V2G0-S112
  • D-Link DVG-1120S | Manual - Page 8
    Web-based Management In order to use a web browser to configure the VoIP gateway, you must make sure it has a valid Ethernet connection to a PC or LAN via its LAN port. Access the configuration utility to check the LAN port by entering the IP Address into your web browser address field. Type 192.
  • D-Link DVG-1120S | Manual - Page 9
    Properties> double click Internet Protocol (TCP/IP). The screen at right will appear. The VoIP gateway's WAN port comes with DHCP as the default IP setting. If the VoIP gateway cannot get the assigned DHCP IP, it will use the manual IP (default is 10.1.1.1 ) as it's default IP. Make sure the PC is
  • D-Link DVG-1120S | Manual - Page 10
    More WAN IP Configuration settings include: Config IP - Config WAN IP Address Get IP From Choose the method that the VoIP gateway will use to obtain its IP settings once it is restarted. Choices include: Manual - When Manual is chosen, the VoIP gateway will obtain its IP settings from the fields
  • D-Link DVG-1120S | Manual - Page 11
    for the VoIP gateway. Click Save to save the settings. Config IP - Config LAN IP Address Device Type - The model name of this device. Device Information MAC Address - The MAC address of this device. Boot PROM Version - The version number of the device's startup code. Firmware Version The
  • D-Link DVG-1120S | Manual - Page 12
    Web-based Management (continued) Proxy DNS State - Enables or disables the Proxy DNS function. Proxy DNS IP Address - Enter the Proxy DNS IP Address. Click Save to save the settings. 12
  • D-Link DVG-1120S | Manual - Page 13
    Web-based Management (continued) Signaling ToS - Set the Type of Service value for VoIP signaling Telephony Configuration RTP ToS - Set the Type of Service value for RTP packets Receive Gain - Set the Receive gain of the device. (-14 to +14 dB) Transmission Gain - Set the Transmit gain of the
  • D-Link DVG-1120S | Manual - Page 14
    Min-SE time. Session Expires Refresher - Choose uac or uas. Click on the Save button at the bottom right of the screen to save the settings. SIP (Session Initiated Protocol) is the type of call management for VoIP that is used by the DVG-1120S. 14
  • D-Link DVG-1120S | Manual - Page 15
    ) Same Phone Number- Enable or disable. SIP Configuration - User Agent Index - Choose Phone 1 or Phone 2. Phone Number - A user-defined phone number for each phone port. Display Name - A user-defined display name for each phone port. Caller ID Delivery - Enable or disable this function
  • D-Link DVG-1120S | Manual - Page 16
    (continued) This window displays the Peer to Peer setting for non-SIP server mode. It lists the ten numbers, which support Peer to Peer communication. SIP Configuration - Peer to Peer Click the Edit icon to access the second SIP Configuration-Peer to Peer window, shown below: Index - Choose
  • D-Link DVG-1120S | Manual - Page 17
    Configuration - Generic Configuration This is a userdefined ACR (Automatic Call Redirection) table. The user can choose and setup the default line through VoIP or PSTN. If the default is VoIP of a VoIP call to PSTN whenever the "4xx, 5xx, 6xx" error message is received from the SIP server. No
  • D-Link DVG-1120S | Manual - Page 18
    ) The first ACR Configuration window lists thirty numbers, each supports a maximum of 31 digits in one number. When the first dialed digits match the table, the system will store all the digits and forward them to the non-default line. ACR Configuration - ACR Configuration Click the Edit icon
  • D-Link DVG-1120S | Manual - Page 19
    Configuration (continued) 1. A full telephone number, e.g., 555-5555: The system will transmit the number to the non-default line, when the user Click on the Save button at the bottom right of the window to save the settings. Another way to access the non-default line is to input a prefix when
  • D-Link DVG-1120S | Manual - Page 20
    window, shown below: After you have clicked on an edit icon, this window will appear. Type in an appropriate identifying comment for the IP Filter set. 2nd IP Filter window For more editing options, click the icon once again and the 3rd IP Filter window will appear. When you are finished
  • D-Link DVG-1120S | Manual - Page 21
    packets only. Select a range of ports to pass or block. Use the following guide to define the port or port range (Start Port and End Port): < the port numbers greater than and equal to the Start Port number. = : Sets the port number equal to the Start Port if there is no End Port specified
  • D-Link DVG-1120S | Manual - Page 22
    the window to save the settings. Routing - RIP Use Static Routing to specify a route used for data traffic within your WAN or LAN. This can be used to specify that all packets destined for a particular subnet use a predetermined gateway. Routing - Static Route Configuration Click the Edit icon
  • D-Link DVG-1120S | Manual - Page 23
    Click on the Save button at the bottom right of the window to save the settings. Click on the Clear button at the bottom right of the window to clear the settings. Bridge Mode To enable Bridge Mode, select ON; to disable Bridge Mode, select OFF. Click on the Save button at the bottom right of the
  • D-Link DVG-1120S | Manual - Page 24
    IP Address for the pool of unassigned IP Addresses. DHCP Configuration - Dynamic IP Assignment IP Range - This is the range Enter the appropriate Netmask for the environment. Default Gateway - Enter the IP Address of the Default Gateway Leased Time - This specifies the amount of settings. 24
  • D-Link DVG-1120S | Manual - Page 25
    Address of its NIC which must be entered on the next screen. DHCP Configuration - Static IP Assignment Click the Edit icon on the window above to is the static IP Address to be assigned. All other parameters (Netmask, Gateway, DNS Server IP, WINS Server IP, Domain Name and State) are identical
  • D-Link DVG-1120S | Manual - Page 26
    the NAT function pull-down menu. Click on Save to save the settings. NAT Configuration - NAT Configuration This window allows you to view the current local server configuration settings. NAT Configuration - Local Server Configuration Click the Edit icon on the window above to access the second
  • D-Link DVG-1120S | Manual - Page 27
    Choose the index number that you would like to edit (From 1 to 6). Local Server Configuration - 2nd window Protocol- Choose either TCP or UDP protocol . Global Port - Enter the or device. State- Disable or Enable the Local Server Configuration function. Click Save to save the settings. 27
  • D-Link DVG-1120S | Manual - Page 28
    ) This window allows you to view the current Dynamic NAT settings when Dynamic NAT is chosen. Each entry, in this configuration, can be used to map multiple, contiguous global addresses and local addresses to each other. NAT Configuration - Dynamic NAT Click the Edit icon on the window above
  • D-Link DVG-1120S | Manual - Page 29
    Web-based Management (continued) This window allows you to view the current Static NAT settings when Static NAT is chosen. NAT Configuration - Static NAT Click the Edit icon on the window above to access the second - Select Disable or Enable Static NAT function. Click Save to save the settings. 29
  • D-Link DVG-1120S | Manual - Page 30
    - The IP Address of the trap receiving station. SNMP Trap Configuration Community Name A user-defined SNMP community name. SNMP AuthTrap Enable or disable the SNMP trap. Click Save to save the settings. This window supports two SNMP manager IP Addresses for accessing this device, and only
  • D-Link DVG-1120S | Manual - Page 31
    Web-based Management (continued) To add or change a User Account, fill in the appropriate information in the User Name, Old Password (if applicable), New Password, and Confirm New Password fields. Click Save to save the settings. Administration Management Rx Packets- The total number of packets
  • D-Link DVG-1120S | Manual - Page 32
    Web-based Management (continued) Monitor - Ethernet Statistics (continued) Rx CRC Errors - The number of packets received that failed the CRC checksum test. Rx Overrun Packets - The number of packets received that exceed the 1518 octet maximum length imposed on Ethernet packets. (Overrun packets are
  • D-Link DVG-1120S | Manual - Page 33
    - DSP Statistics Software Update Mode - Image files down through TFTP. Firmware Update TFTP Server Address - The IP Address of the TFTP server where the runtime or configuration file is located. This entry is used only if the Firmware Update is set to Enable. Firmware Update - Determines whether
  • D-Link DVG-1120S | Manual - Page 34
    Before performing a Factory Reset, be absolutely certain that this is what you want to do. Once the reset is done, all of the device's settings stored in NV-RAM will be erased and restored to values present when the device was purchased. Factory Reset Note: After performing the Factory Reset,
  • D-Link DVG-1120S | Manual - Page 35
    software set to emulate a VT100. The console must be connected to the Diagnostics port. This is an RS-232 port with a 9-socket D-shell connector and DCE-type wiring. Make the connection as follows: 1. Obtain suitable cabling for the connection. You can use either (a) a "null-modem" RS-232 cable or
  • D-Link DVG-1120S | Manual - Page 36
    Configuration Using a Console Configuring the VoIP Gateway Using Telnet Once you have set an IP address for your device, you can use a Telnet program (in a VT-100 compatible terminal mode) to access and configure it. Most of the screens are identical, whether accessed from the console port or from a
  • D-Link DVG-1120S | Manual - Page 37
    Configuration Using a Console First Time Connecting to the VoIP Gateway Configuration Commands You can type "nwdbg" to see all of the configuration commands. (Shown Below) 37
  • D-Link DVG-1120S | Manual - Page 38
    Configuration Using a Console Configuration Commands This 192.168.0.1> command line allows you to enter the related commands for the inital configuration of this device. Configure IP Type "nwdbg ipgw" to show the IP setting of th edevice (default is PPoE). 38
  • D-Link DVG-1120S | Manual - Page 39
    Configuration Using a Console Configure IP The following commands are use for device's IP setting: nwdbg ip - set to DHCP, BOOTP, Manual (static IP) or PPPoE mode. If Manual mode: nwdbg ip - set device ip to d.d.d.d nwdbg mask - set device subnet
  • D-Link DVG-1120S | Manual - Page 40
    Using the Console Port The DVG-1120S VoIP gateway features a Console Port for debugging, which is described in this section. To access the console mode, you must first make sure the console is connected to the Diagnostics port and the appropriate cabling for the connection is being used. (You need a
  • D-Link DVG-1120S | Manual - Page 41
    Using the Console Port Configuration Commands You can type "nwdbg" and press to see all of the configuration commands. (Shown below) 41
  • D-Link DVG-1120S | Manual - Page 42
    Using the Console Port Configuration Commands The 192.168.0.1> command line allows you to enter the related commands for the initial configuration of this device. Configure IP Type "nwdbg ipgw" and press to show the IP setting of the device (default is PPPoE). 42
  • D-Link DVG-1120S | Manual - Page 43
    Using the Console Port Configure IP The following commands are use for device's IP setting: nwdbg ip - set to DHCP, BOOTP, Manual (static IP) or PPPoE mode. If Manual mode: nwdbg ip - set device ip to d.d.d.d nwdbg mask - set device subnet mask to
  • D-Link DVG-1120S | Manual - Page 44
    Using the Console Port Firmware Upgrade New software can be downloaded from a TFTP server. You can type TFTP to see the TFTP update commands. (Shown below) Console mode--TFTP Update Firmware Commands Screen The items on this window are described below: tftp srvip - set the IP address of
  • D-Link DVG-1120S | Manual - Page 45
    factory reset" on the 192.168.0.1> command line and press . The following window will appear: Console mode--nwdbg Factory Reset Command Screen Once the reset is done, all of the device's settings stored in NV-RAM will be erased and restored to values present when the device was purchased. The
  • D-Link DVG-1120S | Manual - Page 46
    Command Line Interface The DVG-1120S VoIP Gateway offers a line-at-a-time prompt and response scheme to execute various configuration instructions. The interface displays a single prompt character 192.168.0.1> when it is ready to accept a command (ex. 192.168.0.1>set or 192.168.0.1>show). Typing a
  • D-Link DVG-1120S | Manual - Page 47
    Command Line Interface General Setup Commands nwdbg un Definition: This command sets the username if there is a username 12 Example: nwdbg un 123456789012 nwdbg pw Definition: This command sets the password if there is a password string, or shows the username/password
  • D-Link DVG-1120S | Manual - Page 48
    Setup nwdbg mac Definition: This command sets the MAC address of the voice link, or shows the MAC address if only nwdbg manual> Definition: This command sets the software boot mode to DHCP, BOOTP, or Manual mode. If only nwdbg ip is typed, this command shows the IP configuration
  • D-Link DVG-1120S | Manual - Page 49
    as the system's subnet mask if the software boot mode is Manual mode. If only nwdbg mask is typed, this command shows the IP configuration. Parameter(s): Example: nwdbg mask 255.0.0.0 nwdbg gw Definition: This command sets the fixed GW address, which is used as the
  • D-Link DVG-1120S | Manual - Page 50
    Command Line Interface General Setup Commands nwdbg tftp Definition: This command sets the software download link to either a WAN link or a LAN link. If only nwdbg tftp is typed, this command shows the download link. Parameter(s): Example: nwdbg tftp 0 nwdbg
  • D-Link DVG-1120S | Manual - Page 51
    Command Line Interface General Setup Commands nwdbg dns Definition: This command Kong, 3:Sweden> Example: nwdbg country 1 nwdbg gain Definition: This command sets the receive and transmit gain, or shows the state if only nwdbg gain is
  • D-Link DVG-1120S | Manual - Page 52
    TFTP Client Setup Commands When the user enters tftp, the screen will show all commands about the TFTP client: ggdbg>tftp tftp srvip - set the IP in EEPROM will be employed. tftp update - update the image in flash Current Settings : TFTP Server IP Address : 172.16.6.245 Image File
  • D-Link DVG-1120S | Manual - Page 53
    be displayed. When the user enters tftp get, the file name in EEPROM will be employed. Example: ggdbg>tftp get c:\102nmm.tfp Download d:\project\dg102\102nmm.tfp ...\ OK tftp update Definition: Example: This command updates the image in FLASH. The image is downloaded for storage in DRAM. If
  • D-Link DVG-1120S | Manual - Page 54
    Networking Basics Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home computers using Windows 2000, ME or 98. Go to Start>Control Panel>Network Connections Select Set up a home or small office network When this screen appears, Click Next. 54
  • D-Link DVG-1120S | Manual - Page 55
    Networking Basics (continued) Please follow all the instructions in this window: Click Next In the following window, select the best description of your computer. If your computer connects to the internet through a gateway/router, select the second option as shown. Click Next 55
  • D-Link DVG-1120S | Manual - Page 56
    Networking Basics (continued) Enter a Computer description and a Computer name (optional.) Click Next Enter a Workgroup name. All computers on your network should have the same Workgroup name. Click Next 56
  • D-Link DVG-1120S | Manual - Page 57
    Networking Basics (continued) Please wait while the Network Setup Wizard applies the changes. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer. This may take a few minutes. 57
  • D-Link DVG-1120S | Manual - Page 58
    Networking Basics (continued) In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next. Insert a disk into the Floppy Disk
  • D-Link DVG-1120S | Manual - Page 59
    Basics (continued) Please wait while the Network Setup Wizard copies the files. Please read the information under Here's how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on
  • D-Link DVG-1120S | Manual - Page 60
    this screen, then click Finish to complete the Network Setup Wizard. The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your
  • D-Link DVG-1120S | Manual - Page 61
    Networking Basics (continued) Naming your Computer To name your computer, in Windows XP, please follow these directions: Click Start (in the lower left corner of the screen) Right-click on My Computer Select Properties and click Select the Computer Name Tab in the System Properties window. You may
  • D-Link DVG-1120S | Manual - Page 62
    Address in Windows XP The wireless adapter-equipped computers in your network must be in the same IP Address range (see Getting Started in this manual for a definition of IP Address Range). To check on the IP Address of the adapter, please do the following: Right-click on the Local Area
  • D-Link DVG-1120S | Manual - Page 63
    DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP Addresses. If you are not using a DHCP capable Gateway/Router, or you need to assign a Static IP Address, please follow these instructions: Go to Start Double
  • D-Link DVG-1120S | Manual - Page 64
    Networking Basics (continued) Assigning a Static IP Address in Windows XP/2000 Double-click on Network Connections Right-click on Local Area Connections Double-click on Properties 64
  • D-Link DVG-1120S | Manual - Page 65
    the same for all the computers on the network). IP Address: e.g., 192.168.0.2 Subnet Mask: 255.255.255.0 Default Gateway: Enter the LAN IP address of the wireless router. (D-Link wireless routers have a LAN IP address of 192.168.0.1) Select Use the following DNS server addresses. Enter the LAN IP
  • D-Link DVG-1120S | Manual - Page 66
    Macintosh OSX Go to the Apple Menu and select System Preferences Click on Network Select Built-in Ethernet in the Show pull-down menu Select Manually in the Configure pull-down menu Input the Static IP Address, the Subnet Mask and the Router IP Address in the appropriate fields Click Apply Now 66
  • D-Link DVG-1120S | Manual - Page 67
    the Apple Menu and select System Preferences Click on Network Select Built-in Ethernet in the Show pull-down menu Select Using DHCP in the Configure pull-down menu Click Apply Now The IP Address, Subnet mask, and the Router's IP Address will appear in a few seconds 67
  • D-Link DVG-1120S | Manual - Page 68
    this one will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP Address of the Wireless Router or Access Point. A good wireless connection will show four replies from the Wireless Router or Access Point, as shown. Checking the Wireless Connection by Pinging in Windows Me and 98 Go to
  • D-Link DVG-1120S | Manual - Page 69
    Ethernet compliant Quality of Service: Voice service is prioritized over the data traffic FAX support: V.21, V.27ter, V.29, V.17 Modulation/Demodulation Network Protocols: TCP/IP, UDP, ARP, ICMP, TFTP, Telnet, SNMP, HTTP, RIP1/ RIP2 DHCP: Dynamic Host Configuration Protocol server and client NAT
  • D-Link DVG-1120S | Manual - Page 70
    Link/Act Phone 1 to 2: PSTN/VoIP Hook/Ringing Dimensions: 6.78" (W) x 6.165" (D) x 1.339" (H) (172mm x 156.6mm x 34mm) Number of Ports: One 10BASE-T Ethernet port (WAN) One 10/100BASE-TX Fast Ethernet port (LAN) Two loop-start FXS RJ-11 ports One PSTN POTS RJ-11 port for Life Line One RJ-14 Console
  • D-Link DVG-1120S | Manual - Page 71
    Technical Specifications (continued) Power Supply: AC-to-DC power adapter (provided) DC Input: 12VDC/1A Operating Temperature: 0-50°C Storage Temperature: -10-55°C Humidity: 5% - 95% non-condensing Safety: UL/CUL Emission (EMI): FCC part 68 VCCI Class B 71
  • D-Link DVG-1120S | Manual - Page 72
    find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our
  • D-Link DVG-1120S | Manual - Page 73
    to refund at D-Link's sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement ") will substantially conform to D-Link's then current functional specifications for the Software, as set forth in the applicable documentation,
  • D-Link DVG-1120S | Manual - Page 74
    package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective firmware or other products or services provided by anyone other than DLink; Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link
  • D-Link DVG-1120S | Manual - Page 75
    , Inc., as stipulated by the United States Copyright Act of 1976. Contents are subject to change without prior notice. Copyright© 2003 by D-Link Corporation/D-Link Systems, Inc. All rights reserved. FCC Statement: This equipment has been tested and found to comply with part 68 of the FCC Rules
  • D-Link DVG-1120S | Manual - Page 76
    Registration Register your D-Link product online at http://support.dlink.com/register/ (10/08/04) 76
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
VoIP Residential Gateway
with Two Voice Ports
Manual
Building Networks for People
D-Link
DVG-1120S