D-Link DVG-1402S Product Manual
D-Link DVG-1402S - Express ENwork Router Manual
 |
UPC - 790069270543
View all D-Link DVG-1402S manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DVG-1402S manual content summary:
- D-Link DVG-1402S | Product Manual - Page 1
D-Link DVG-1402S Broadband Phone Service VoIP Router Manual Building Networks for People (09/24/04) - D-Link DVG-1402S | Product Manual - Page 2
10 Connecting the DVG-1402S in Front of a Router 13 Configuring the DVG-1402S for DSL Connection 15 Connecting the DVG-1402S Behind a Router 18 MAC Cloning for Cable Connection 21 Web-based Management 22 Frequently Asked Questions 44 Technical Specifications 47 Technical Support 50 Warranty - D-Link DVG-1402S | Product Manual - Page 3
of Package: D-Link DVG-1402S Broadband Phone Service VoIP Router 12V DC/1.25A Power Adapter CD-ROM with Manual Quick Installation Guide Ethernet Cable Standard (RJ-11) Telephone Cable Note: Using a power supply with a different voltage rating than the one included with the DVG-1402S will cause - D-Link DVG-1402S | Product Manual - Page 4
Introduction The D-LINK DVG-1402S Broadband Phone Service VoIP Router links traditional telephony networks to IP networks with conventional telephony devices such as analog phones or fax machines. The DVG-1402S includes two RJ-11 telephone jacks that provide voice communication over the IP network, - D-Link DVG-1402S | Product Manual - Page 5
Connects to your broadband modem using an Ethernet cable. Reset This is used to reset the unit to the factory default settings. Power Connector The power adapter attaches here. Warning! Using a different power adapter than the one included with your purchase will damage the DVG-1402S and void - D-Link DVG-1402S | Product Manual - Page 6
Host Configuration Protocol) or static configuration Remote software download/update Supports IP sharing to allow multiple users to access the Internet via a single IP address Supports Caller ID Supports QoS to guarantee voice quality Optional features may be supported by your service provider - D-Link DVG-1402S | Product Manual - Page 7
or is registering with the service provider. The Status LED will flash green slowly when the system is connected with the service. The Alarm LED will light make sure your devices are powered on. Phone LEDs This LED displays the VoIP status and Hook/Ringing activity on the phone port that is used to - D-Link DVG-1402S | Product Manual - Page 8
a DSL or Cable modem and does not connect to a router, follow the steps below to install your DVG-1402S. After the steps are completed, your setup should look similar to the diagram below. Note: This is the most common setup configuration for the DVG-1402S. If you do not require the use of more than - D-Link DVG-1402S | Product Manual - Page 9
the modem into one of the four LAN ports on the back of the DVG-1402S. The other end remains attached to the PC. 5. Attach one end of the Attach the other end of the provided Ethernet Cable to the WAN Port of the DVG-1402S. 7. Attach one end of the provided phone cable (black) to a standard analog - D-Link DVG-1402S | Product Manual - Page 10
IP address from the DVG-1402S) regardless of what type of internet connection you have. (Please refer to your NIC card's manual for detailed information.) If your cable service provider does not require a MAC address, setup of the DVG-1402S with a modem and computer is complete. Configuring the DVG - D-Link DVG-1402S | Product Manual - Page 11
) Connecting the DVG-1402S Directly to a Modem and Computer (No Router) Click Login to the webbased management module. Click Configure WAN/LAN Access. Click Configure WAN Port. Select PPPoE from the pull-down menu. Enter your User Name and Authentication Password and Confirm Password. Click Save - D-Link DVG-1402S | Product Manual - Page 12
the DVG-1402S Directly to a Modem and Computer (No Router) Select Save changes and reboot system now. Click Save. Once the unit reboots you will be returned to the main screen. Check to see if the status LED light is blinking green on the front panel of the DVG-1402S. Setup of the DVG-1402S with - D-Link DVG-1402S | Product Manual - Page 13
the DVG-1402S in Front of a Router If you wish to connect your DVG-1402S in front of a router, follow the steps below. After the steps are completed, your setup should look similar to the diagram below. This is the recommended method for setting up the DVG-1402S. This set up allows the DVG-1402S to - D-Link DVG-1402S | Product Manual - Page 14
. Be sure that the Cat 5 Ethernet Cable that is plugged into the LAN Port of your existing router is still plugged into your PC. 11. Unpack the Telephone Cable (black) that came with the DVG-1402S. 12. Attach one end of this cable to a standard analog telephone. 13. Attach the other end of - D-Link DVG-1402S | Product Manual - Page 15
IP address from the DVG1402S) regardless of what type of internet connection you have. (Please refer to your NIC card's manual for detailed information.) If your cable service provider does not require a MAC address, setup of the DVG-1402S with a modem and computer is complete. Configuring the DVG - D-Link DVG-1402S | Product Manual - Page 16
Started (continued) Connecting the DVG-1402S in Front of a Router Click Login to the webbased management module. Click Configure WAN/LAN Access. Click Configure WAN Port. Select PPPoE from the pull-down menu. Enter your User Name and Authentication Password and Confirm Password. Click Save. 16 - D-Link DVG-1402S | Product Manual - Page 17
continued) Connecting the DVG-1402S in Front of a Router Select Save changes and reboot system now. Click Save. Once the unit reboots you will be returned to the main screen. Check to see if the status LED light is blinking green on the front panel of the DVG-1402S. Setup of the DVG-1402S with a DSL - D-Link DVG-1402S | Product Manual - Page 18
Getting Started (continued) Connecting the DVG-1402S Behind a Router If you wish to connect your DVG-1402S behind a router, follow the steps below. After the steps are completed, your setup should look similar to the diagram below. 1. Turn off your Computer. 2. Disconnect the power to the Cable/DSL - D-Link DVG-1402S | Product Manual - Page 19
sure that the Cat 5 Ethernet Cable that is plugged into the "WAN" Port of your existing router is still plugged into your Cable/DSL Modem. 11. Unpack the Telephone Cable (black) that came with the DVG-1402S. 12. Attach one end of this cable to a standard analog telephone. 13. Attach the other end - D-Link DVG-1402S | Product Manual - Page 20
PC. By default the unit is already configured to work behind a router. Be sure to change your computer's IP settings to DHCP (to automatically be assigned an IP address from the DVG-1402S) regardless of what type of internet connection you have. (Please refer to your NIC card's manual for detailed - D-Link DVG-1402S | Product Manual - Page 21
:aa:bb:11:22:33. 3. Open a Web browser and type in the IP address of the DVG-1402S (default is 192.168.15.1). Log into the Web-based management module (see the next section for more information) and click on Configure WAN Port. The following page will appear. 4. Select DHCP from the connection type - D-Link DVG-1402S | Product Manual - Page 22
VoIP gateway cannot get the assigned DHCP IP, it will use the manual IP (default is 192.168.15.1 ) as it's default IP. 192 . 168 . 15 . 15 255 . 255 . 255 . 0 Set your PC's IP address to 192.168.15.15 and the subnet mask to 255.255.255.0. In order to use a Web browser to configure the VoIP Router - D-Link DVG-1402S | Product Manual - Page 23
Web-based Management (continued) Click on Login to the Web-based Management module Setting Up the Connection To configure the WAN port, please do the following: Click on Configure WAN Port. Choose your type of connection. Manually enter your DNS address (if applicable). 23 - D-Link DVG-1402S | Product Manual - Page 24
advanced users.) By default the LAN IP Address is: 192.168.15.1 After you have configured your WAN and LAN ports you can click on Save and Restart System in the Configuration menu, or you can continue to configure the VoIP Router. After you have completed configuring the VoIP Router, you must Save - D-Link DVG-1402S | Product Manual - Page 25
Port > Proxy DNS State - This toggles Enable and Disable for the Proxy DNS function. Proxy DNS IP Address - Enter the Proxy DNS IP address if instructed by your service provider. Click Save to save the settings. Configure LAN Port > Bridge Mode Bridge Mode - This toggles On and Off to turn NAT on or - D-Link DVG-1402S | Product Manual - Page 26
-based Management (continued) Configure LAN Port > DHCP Configuration > Dynamic IP Assignment Use the Dynamic IP Assignment to configure the device to act as a DHCP server for the LAN. The items on this window are described below: Default Gateway - This specifies the Gateway IP Address that will be - D-Link DVG-1402S | Product Manual - Page 27
particular host that will receive the below IP address. IP Address - This is the static IP address to be assigned. All other parameters (Netmask, Gateway, DNS Server IP, WINS Server IP, Domain Name and State) are identical to those in the Dynamic IP Assignment, in the previous section. Click Save - D-Link DVG-1402S | Product Manual - Page 28
Select enabled or disabled for the NAT function. Click Save to save the settings. Configure LAN Port > NAT Configuration > Virtual Server Configuration This window allows you to view the current virtual server configuration settings. Click the edit icon on this window to access the second Virtual - D-Link DVG-1402S | Product Manual - Page 29
Range - Enter the port number used by the designated host on the LAN or use a well-known port. Server IP - Enter the IP address of the local designated host computer or device. State - This toggles Disable and Enable for the Virtual Server Configuration function. Click Save to save the settings. 29 - D-Link DVG-1402S | Product Manual - Page 30
Server Configuration (continued) The items on this window are described below: DMZ Forwarding Mode - Select to enable or disable the DMZ. The DMZ (Demilitarized Zone) allows a single computer to be exposed to the internet. By default the DMZ is disabled. DMZ Host IP Address - Enter the IP address - D-Link DVG-1402S | Product Manual - Page 31
-based Management (continued) Configure LAN Port > NAT Configuration > Dynamic NAT (continued) The items on this window are described below: Index - Choose the index number that you would like to edit (Form 1 to 6). Global IP Start Enter the beginning designated IP address for the particular range - D-Link DVG-1402S | Product Manual - Page 32
-based Management (continued) Configure LAN Port > NAT Configuration > Static NAT This IP Address - Enter the designated IP address for the packet you wish to redirect to a Global address. Global IP Address - Enter the designated IP address for the packet you wish to redirect to a Local address - D-Link DVG-1402S | Product Manual - Page 33
RIP, routers periodically exchange entire tables. Configure LAN Port > Routing > Static Route Configuration Use Static Routing to specify a route used for data traffic within your WAN or LAN. This can be used to specify that all packets destined for a particular subnet use a predetermined gateway - D-Link DVG-1402S | Product Manual - Page 34
Configuration (continued) The items on this window are described below: IP Address - Type in the IP Address of the subnet or device where packets are routed. Subnet Mask - Type in an appropriate subnet mask that allows the static route to function. Gateway - Type in the IP Address of the gateway - D-Link DVG-1402S | Product Manual - Page 35
disable the listed Firewall rules sets. Click Save button to save the settings. Click the edit icon on the window above to access the third IP Filter window, shown on the following page: 35 - D-Link DVG-1402S | Product Manual - Page 36
or block packets from that IP Address. Destination- Type in the destination IP Address and select the Subnet Mask to pass or block packets destined to that IP Address. Port Filter Rule- UDP and TCP packets only. Select a range of ports to pass or block. Use the following guide to define the port or - D-Link DVG-1402S | Product Manual - Page 37
menu. TCP Packet Options - Optional TCP packet options include: Acknowledgment, Push, Reset, SYN, and FIN. Consult a certified technician before selecting any of these from accessing the Internet and network by their MAC address. Click the edit icon on the window above to access the MAC Filter window, - D-Link DVG-1402S | Product Manual - Page 38
client that will be filtered. State - This toggles Disable and Enable for the MAC address filtering function for this index. Click the Save button to save the settings. Configure Pass Through Mode The device supports VPN (Virtual Private Network) pass-through for both PPTP (Point-to-Point Tunneling - D-Link DVG-1402S | Product Manual - Page 39
Web-based Management (continued) Statistics > WAN Internet Connection Statistics This window displays a variety of WAN Connection statistics. Statistics > Phone Port Statistics This window displays a variety of Phone Port statistics. 39 - D-Link DVG-1402S | Product Manual - Page 40
Web-based Management (continued) Configuration Restore and Backup The current system settings can be saved as a file onto the local hard drive. The saved file or any other saved setting file created by the DVG-1402S can be uploaded into the unit. To restore a system settings file, click on Browse to - D-Link DVG-1402S | Product Manual - Page 41
the device was purchased. Click on Reset to Factory Default to reset the NV-RAM to the default values that were present when you purchased the device. Note: After performing the Factory Reset, make sure to redefine the IP settings for the device in the IP Configuration menu. Then perform a Restart - D-Link DVG-1402S | Product Manual - Page 42
were present when the device was purchased. Click on Save Configuration at the bottom of the window to save the system settings to NV-RAM. Advanced This section contains advanced configuration settings for the DVG-1402S VoIP Router. Please consult a certified technician before making any changes to - D-Link DVG-1402S | Product Manual - Page 43
Web-based Management (continued) About This read-only window displays information about the DVG-1402S VoIP such as: Device Type, MAC Address, Boot PROM Firmware, Firmware Version, and DSP Version. The DSP Version will list "Not yet loaded" until you initialize your unit. 43 - D-Link DVG-1402S | Product Manual - Page 44
Link DVG-1402S link. 3) Select SIP Configuration. 4) In the Server link, enter the correct information (server address, Port Number, Outbound Proxy server info [if applicable], Domain Name [if applicable], etc.) 5) Select User Agent link and enter the account information provided by your VoIP service - D-Link DVG-1402S | Product Manual - Page 45
the LAN ports of the DVG-1402S and the Ethernet cable from the cable modem is plugged into the WAN port of the DVG1402S. Once this is verified but you still cannot access the Internet, then verify the configurations via the Web GUI. 1) Access the Web GUI by entering the IP address: 192.168.15.1 in - D-Link DVG-1402S | Product Manual - Page 46
) Verify that the WAN port for Public IP is NOT 10.1.1.1. (It must be an IP address given by your Internet Service Provider (ISP) through the Cable or DSL modem.) Q: Can I use my DVG-1402S on a MGCP network? A: No, DVG-1402S is a SIP device and uses the SIP protocol in handling all of the telephony - D-Link DVG-1402S | Product Manual - Page 47
Ethernet compliant Quality of Service: Voice service is prioritized over the data traffic (When unit is connected directly to the modem) Network Protocols: Will route all standard protocols DHCP: Dynamic Host Configuration Protocol server and client NAT: Network Address Translation PPP over Ethernet - D-Link DVG-1402S | Product Manual - Page 48
Technical Specifications (continued) LEDs: General: Power Status/Alarm Ethernet: WAN: 10/100M, Link/Act LAN: 10/100M, Link/Act Phone 1 to 2: MWI Hook/Ringing Provision Light Dimensions: W = 6.77 inches (172mm) D = 6.16 inches (156.6 mm) H = 1.34 inches (34mm) Number of Ports: One 10/100BASE-T - D-Link DVG-1402S | Product Manual - Page 49
Technical Specifications (continued) Safety: UL/CUL Emission (EMI): FCC Class B CE Class B 49 - D-Link DVG-1402S | Product Manual - Page 50
For Technical Support regarding your phone service, please contact the service provider. If you experience any hardware problems with the DVG-1402S, please contact D-Link Technical Support. Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides - D-Link DVG-1402S | Product Manual - Page 51
Installations, addresses with an APO or FPO. Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described or to refund at D-Link's sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware - D-Link DVG-1402S | Product Manual - Page 52
manuals or accessories in the shipping package. D-Link firmware or other products or services provided by anyone other than DLink; Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE - D-Link DVG-1402S | Product Manual - Page 53
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no forth for an uncontrolled environment. Register online your D-Link product at http://support.dlink.com/register/ 09/24/04 53
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
 |
 |
Broadband Phone Service VoIP Router
Manual
(09/2
4
/04)
Building Networks for People
D-Link
DVG-1402S