D-Link DVX-2000MS-10P Quick Installation Guide

D-Link DVX-2000MS-10P - VoiceCenter IP Phone Sys 10P Manual

Get D-Link DVX-2000MS-10P - VoiceCenter IP Phone Sys 10P PDF manuals and user guides
UPC - 790069330858
View all D-Link DVX-2000MS-10P manuals
Add to My Manuals
Save this manual to your list of manuals

D-Link DVX-2000MS-10P manual content summary:

  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 1
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 2
    1.5 and above (for configuration) Package Contents D-Link DVX-2000MS Base Unit D-Link DPH-125MS IP Phones (5 or 10) D-Link DVG-3104MS 4-Port PSTN Gateway Manual, QIG and Software on CD Power Adapters CAT5 Ethernet Cables Phone Cable Note: Using a power supply with a different voltage rating
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 3
    Base Unit and connect the other end of the Ethernet cable to a Local Area Network via switch or hub. The LAN LED will light up to indicate proper connection. When you have connected the DVX-2000MS to your network, it should look like the diagram below:  D-Link VoiceCenter Quick Install Guide
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 4
    on the IP Phone and connect the other end of the Ethernet cable to your Local Area Network using a hub or switch. Repeats steps for additional DPH-125MS IP Phones. When you have connected the IP Phones to your network it should look like the diagram below. D-Link VoiceCenter Quick Install Guide 
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 5
    used by traditional phone service. Note: Avoid disabling your existing phone service while setting up the VoiceCenter™. If you have an alternative jack available, use it to set up and test the VoiceCenter your network, it should look like the diagram below:  D-Link VoiceCenter Quick Install Guide
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 6
    Software Installation Microsoft Response Point Administrator Insert the VoiceCenter™ CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP. If the CD Administrator and click Next to continue. Click Next to continue. D-Link VoiceCenter Quick Install Guide 
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 7
    Accept the License Agreement and click Next to continue. Click Install to begin the installation. Please wait while the InstallShield wizard installs Microsoft® Response Point™ Administrator. Installation is complete, click Finish to exit the wizard.  D-Link VoiceCenter Quick Install Guide
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 8
    program is running, is not connected properly to the LAN. Make sure all cables and power cords are connected. Another potential problem is that the DVX-2000MS base unit is not turned on. Note: If a Security Alert dialog box comes up, click Unblock. D-Link VoiceCenter Quick Install Guide 
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 9
    , type the default password, admin and click Connect. Note: It's recommended that you change this password after logging in for security purposes. You have successfully logged onto the DVX-2000MS base unit. You may now configure your IP Phones and Gateway.  D-Link VoiceCenter Quick Install Guide
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 10
    Configure the DPH-125MS IP Phones In Microsoft® Response Point™ Administrator, use the following steps to configure the DPH-125MS IP Phones. Click the Phone System tab check box confirming the IP Phone is connected and plugged in. Click Next to continue. D-Link VoiceCenter Quick Install Guide 10
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 11
    Select one of the D-Link DPH-125MS IP Phones you just connected and click Next to continue. For this step, you will add a new user and assign that user to the phone you just selected. Click Assign User to open the New User screen. 11 D-Link VoiceCenter Quick Install Guide
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 12
    and optional nick names or titles of the person who will use this phone. You should specify nicknames and titles if you think callers will use when asking for this user. In the Extension number box 3 additional users to this phone or click Next to continue. D-Link VoiceCenter Quick Install Guide 12
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 13
    for you. Click Finish to continue. The IP Phone has been successfully added to the phone system. Click Close to exit the configuration wizard. Repeat instructions on pages 10 through 13 to add additional phones. 13 D-Link VoiceCenter Quick Install Guide
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 14
    tab at the top of the screen if necessary. In the Tasks panel, under Phone Service, click Add Phone Service to launch the Configure Phone Service Wizard. Select the check box confirming the gateway is connected and plugged in. Click Next to continue. D-Link VoiceCenter Quick Install Guide 14
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 15
    Select the D-Link DVG-3104MS Gateway you just connected and click Next to continue. Select the This Port Is Active check box. Enter in box. Click Next to continue. Enter a name for the phone line adapter and click Finish to complete the configuration. 15 D-Link VoiceCenter Quick Install Guide
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 16
    ™ CD in the CD-ROM drive on the employee's computer using VoiceCenter. The step-by-step instructions that follow are shown in Windows® XP. If the CD Autorun function does Response Point Assistant and click Next to continue. Click Next to continue. D-Link VoiceCenter Quick Install Guide 16
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 17
    wait while the InstallShield wizard installs Microsoft® Response Point™ Assistant. Installation is complete, click Finish to exit the wizard. Now take the VoiceCenter CD to other computers, where DPH-125MS IP Phones are located and install Microsoft Response Point Assistant on them as well. 17
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 18
    Assistant. In the Password box, type the password of the user. The default password is 9999. Click Log On to logon to Microsoft Response Point Assistant. For more information on using Microsoft Response Point Assistant, see the VoiceCenter™ User Manual. D-Link VoiceCenter Quick Install Guide 18
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 19
    . To test the DHP-125MS IP Phones with the Microsoft Response Point phone system: Using the first phone, dial the extension number assigned to the user on the second phone jacks, and outlets. Please see the VoiceCenter user manual for more information. 19 D-Link VoiceCenter Quick Install Guide
  • D-Link DVX-2000MS-10P | Quick Installation Guide - Page 20
    World Wide Web http://support.dlink.com Version 1.2 October 16, 2008 ©2008 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link, the D-Link logo, and the VoiceCenter logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States and/or
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20