Dacor DRF42TBI Installation Guide - 42" Four-door Freshzone Plus French D

Dacor DRF42TBI Manual

Get Dacor DRF42TBI PDF manuals and user guides View all Dacor DRF42TBI manuals
Add to My Manuals
Save this manual to your list of manuals

Dacor DRF42TBI manual content summary:

  • 1
  • 2
01
Uncrating the refrigerator
• Remove the brackets from the pallet by
unscrewing the bolts (five per bracket).
02
Attaching the anti-tip bracket
Cabinet
Height
Wooden Wall
8
Concrete wall
Ø
8
[
3
• Bracket height is measured from the floor
and depends on the cabinet height.
• Attach the anti-tip brackets. Ensure the
screws hold the bracket tightly.
• The anti-tip brackets must extend at least
2” (50 mm) over the appliance to secure the
appliance. If this minimum length cannot
be observed for structural conditions
it is possible to do this by fastening a
spacer(wood) behind the anti-tip angle.
* Bracket height = Cabinet height – 4 3/32” (104 mm)
Cabinet height
A
Case 1
83 1/2” (2121 mm)
79 1/2” (2019 mm)
Case 2
84” (2134 mm)
79 7/8” (2030 mm)
03
Cabinet special requirements
10”
(254)
D
A
C
E
F
B
Electric supply
location
6”
(154)
ø1/4”(6.5)
1”
(25.4)
Water supply
location
A : Cabinet Width
B : Cabinet Depth
C : Cabinet Height
D : Electrical supply width location
E : Electrical supply height location
F : Water supply outlet location
*B : Includes the standard door panel
thickness with 1/4”
* Installation insidea cabinet of
this width allows the refrigerator
trim to be attached directly to the
surrounding cabinets.
• Connect refrigerator power cord plug to a
properly earthed receptacle. Set the Master
Power Switch to the “I” (ON) position.
• Check to make sure power to refrigerator
is on by opening refrigerator door to see if
interior lights are on.
42”
A
42” (1067mm)
D
22” (559mm)
B
25” (635mm)
E
80” (2032mm)
C
84” (2134mm)
F
12” (305mm)
04
Moving the refrigerator into its enclosure
±
• According to the type of cabinet, a jig
(positioning aid) can be used to align the
refrigerator’s custom door panel with cabinet
by marking vertical line on the cabinet.
• Position the cabinet side chassis to align with
your vertical line.
05
Leveling the refrigerator
• Attach the refrigerator’s top cover and trim
top cover to the hook at the top front of the
chassis.
• Using your drill and the bit shown below,
engage each of the refrigerator’s adjuster
shafts in turn, and level the refrigerator.
( CW
↑
, CCW
↓
)
Adjust the gap between the furniture and
upper chassis cover to 1/8 in. (3mm ).
• The front and rear leveling legs have a
maximum height adjustment of 3/4 in.
(20mm).
Installation guide
06
Securing the refrigerator
8
• Remove freezer box.
• Secure the refrigerator to its enclosure with
(TH) M4 x 14 screws (6 screws per side, as
shown in the graphic).
07
Attaching the Cabinet Trim
• Attach the trim between the refrigerator and
the cabinet.
08
Attaching the Custom-Door-Panel Brackets
6
6
Custom Panel: STS
• Drive screws each to the top and bottom
brackets as shown in the graphic.
(The other holes on each side of the bracket
are for a different application.)
Panel
Template
REF
FRE
6
Custom Panel: Wood, Other
• The template informs you the position of the
bracket and holes.
• Mark hole positions on every corner of the
panel according to the template and drive
the screws into the holes.
09
Aligning the panel (Order : Top
→
Side
→
Front/Back)
6
5
• There are two panel-adjustment mechanisms
at the top and two at the bottom of the door.
• A side screw to shift the panel side to side;
Screw 1 to shift the panel backward
Screw 2 to shift the panel forward
• To attach the Panel to the Door, screw nuts
snugly onto the double-threaded bolts.
(2 nuts per door)
DA68-03686A-00
CAUTION
Please read the installation insturctions carefully before you install the product.
No
NAME
Q'TY
1
PANEL BRACKET L-UP, R-LOW
4
2
PANEL BRACKET R-UP, L-LOW
4
3
ANTI-TIP BRACKET
2
4
NUT-HEXAGON FLANGE
8
5
BOLT-HEX
44
6
SCREW-TAPPING
40
7
SCREW-TAPPING
12
8
SCREW-TAPPING
6
9
TOP TABLE
1
10
LOWER DOOR CAP REF LEFT
1
11
LOWER DOOR CAP REF RIGHT
1
12
UPPER DOOR CAP FRE LEFT
1
13
UPPER DOOR CAP FRE RIGHT
1
14
TRIM TOP COVER
1
15
GAP GUIDE
1
16
HOLDER LOCK
6
17
BRACKET TEMPLATE-REF
1
18
BRACKET TEMPLATE-FRE
1
19
INSTALLATION GUIDE
1
M13
M6 x 12
(FH) M4 X 14
(TH) M4 X 16
M4 x 35
T-Type