Dell Alienware Aurora R11 Service Manual

Dell Alienware Aurora R11 Manual

Get Dell Alienware Aurora R11 PDF manuals and user guides View all Dell Alienware Aurora R11 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell Alienware Aurora R11 manual content summary:

  • Dell Alienware Aurora R11 | Service Manual - Page 1
    Alienware Aurora R11 Service Manual Regulatory Model: D23M Regulatory Type: D23M002
  • Dell Alienware Aurora R11 | Service Manual - Page 2
    of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be
  • Dell Alienware Aurora R11 | Service Manual - Page 3
    Contents 1 Working inside your computer...6 Safety instructions...6 Before working inside your computer...6 Before you begin ...6 Electrostatic discharge-ESD protection...6 ESD field service kit ...7 Transporting sensitive components...8 After working inside your computer...8 2 Removing and
  • Dell Alienware Aurora R11 | Service Manual - Page 4
    Installing the right tron-light board...35 Processor liquid-cooling assembly...36 Removing the processor liquid-cooling assembly...36 Installing the processor liquid-cooling assembly...38 Coin-cell battery...40 Removing the coin-cell battery...40 Installing the coin-cell battery...41 Memory modules
  • Dell Alienware Aurora R11 | Service Manual - Page 5
    Removing the system board...89 Installing the system board...91 Entering the Service Tag in the BIOS setup program 93 3 Device drivers...95 100 Clearing CMOS settings...102 Clearing forgotten password...103 5 Troubleshooting...104 System diagnostic lights...104 Recovering the operating system...104
  • Dell Alienware Aurora R11 | Service Manual - Page 6
    more safety best practices, see the Regulatory Compliance home page at www.dell.com/ troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions
  • Dell Alienware Aurora R11 | Service Manual - Page 7
    strap are prone to damage over time. When using an unmonitored kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the best method for doing this test. If you do not have your own wrist strap
  • Dell Alienware Aurora R11 | Service Manual - Page 8
    service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell stable base, and point your toes out. 2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load. 3. Lift with
  • Dell Alienware Aurora R11 | Service Manual - Page 9
    Removing and installing components Inside view of your computer 1. power-supply unit 3. 2.5-inch hard-drive cage 5. system board 7. processor fan and liquid cooling assembly 9. 3.5-inch hard-drive cage 2. 2.5-inch hard drive 4. graphics card 6. VR heat sink 8. top cover 9
  • Dell Alienware Aurora R11 | Service Manual - Page 10
    System-board components 1. power-supply connector 2. front-panel USB cable 2 (F_USB2) 3. front-panel USB cable 1 (F_USB1) 4. SATA 6 Gbps drive connector (SATA1) 5. SATA 6 Gbps drive connector (SATA2) 6. SATA 6 Gbps drive connector (SATA3) 7. SATA 6 Gbps drive connector (SATA4) 8. solid-state
  • Dell Alienware Aurora R11 | Service Manual - Page 11
    Screw list NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is restored when the component is replaced. NOTE: Some
  • Dell Alienware Aurora R11 | Service Manual - Page 12
    Component System board Secured to Chassis Screw type #6-32 Quantity 8 Screw image Left-side cover Removing the left-side cover Prerequisites 1. Follow the procedure in Before working inside your computer. About this task The following images indicate the location of the left-side cover and
  • Dell Alienware Aurora R11 | Service Manual - Page 13
    Steps 1. Locate the tabs on the left-side cover and slots on the chassis. 2. Rotate the left-side cover towards the chassis until it snaps into place. 3. Replace the screw (6-32x12-7L) that secures the side-cover release latch to the chassis. Next steps 1. Follow the procedure in After working
  • Dell Alienware Aurora R11 | Service Manual - Page 14
    Steps Starting from the rear, pull up on the top cover to release it from the chassis. NOTE: Top cover is tightly secured to the chassis by clips and may requires force to remove it off the chassis. Installing the top cover Prerequisites If you are replacing a component, remove the existing
  • Dell Alienware Aurora R11 | Service Manual - Page 15
    Steps Align the tabs on the top cover with the slots on the chassis and snap the top cover into place. Next steps 1. Install the left-side cover. 2. Follow the procedure in After working inside your computer. Right-side cover Removing the right-side cover Prerequisites 1. Follow the procedure in
  • Dell Alienware Aurora R11 | Service Manual - Page 16
    Steps 1. Starting from the top-front tab, pull the right-side cover away from the chassis. 2. Remove the right-side cover from the chassis. Installing the right-side cover Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
  • Dell Alienware Aurora R11 | Service Manual - Page 17
    17
  • Dell Alienware Aurora R11 | Service Manual - Page 18
    Steps 1. Align the tabs on the right-side cover with the slots on the chassis 2. Rotate the right-side cover towards the chassis until it snaps into place. Next steps 1. Install the top cover. 2. Install the left-side cover. 3. Follow the procedure in After working inside your computer. 2.5-inch
  • Dell Alienware Aurora R11 | Service Manual - Page 19
    Steps 1. Disconnect the data and power cables from the hard drive. 2. Press the release tabs on the hard-drive carrier and slide the hard-drive assembly out of the hard-drive cage. 3. Pry the hard-drive carrier to release the tabs on the assembly from the slots on the hard drive. 4. Lift the hard
  • Dell Alienware Aurora R11 | Service Manual - Page 20
    NOTE: Note the orientation on the hard-drive carrier to replace it correctly. 20
  • Dell Alienware Aurora R11 | Service Manual - Page 21
    Steps 1. Align the hard drive with the pins on the hard-drive carrier. 2. Using the tabs on the opposite side, flex open the carrier to insert the pins on the other side. 3. Slide the hard-drive assembly into the hard-drive cage until it snaps into place. 4. Connect the data cable and power cable to
  • Dell Alienware Aurora R11 | Service Manual - Page 22
    Steps 1. Disconnect the data and power cables from the hard drive. 2. Press the release tabs on the hard-drive carrier and slide the hard-drive carrier out of the hard-drive cage. 3. Pry the hard-drive carrier to release the tabs on the carrier from the slots on the hard drive. 4. Lift the hard
  • Dell Alienware Aurora R11 | Service Manual - Page 23
    NOTE: Note the orientation on the hard-drive carrier to replace it correctly. 23
  • Dell Alienware Aurora R11 | Service Manual - Page 24
    Steps 1. Align the hard drive with the pins on the hard-drive carrier. 2. Using the tabs on the opposite side, flex open the carrier to insert the pins on the other side. 3. Slide the hard-drive assembly into the hard-drive cage until it snaps into place. 4. Connect the data and power cables to the
  • Dell Alienware Aurora R11 | Service Manual - Page 25
    Installing the 2.5-inch hard-drive cage Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the 2.5-inch hard-drive cage and provides a visual representation of the
  • Dell Alienware Aurora R11 | Service Manual - Page 26
    About this task The following images indicate the location of the 3.5-inch and provides a visual representation of the removal procedure. Steps 1. Remove the two screws (#6-32) that secure the 3.5-inch hard-drive cage to the chassis. 2. Lift the 3.5-inch hard-drive cage off the chassis. Installing
  • Dell Alienware Aurora R11 | Service Manual - Page 27
    Steps 1. Insert the 3.5-inch hard-drive cage into its slot on the chassis. 2. Align the tabs on the cage with the tabs on the chassis. 3. Replace the two screws (#6-32) that secure the 3.5-inch hard-drive cage to the chassis. Next steps 1. Install the left-side cover. 2. Follow the procedure in
  • Dell Alienware Aurora R11 | Service Manual - Page 28
    28
  • Dell Alienware Aurora R11 | Service Manual - Page 29
    Steps 1. Remove the two screws (#6-32) that secure the power-supply unit bracket to the power-supply unit cage. 2. Lift the power-supply unit bracket off the power-supply unit cage. 3. Lift the power-supply unit cage and rotate the power-supply unit cage away from the chassis. 4. Press the releasing
  • Dell Alienware Aurora R11 | Service Manual - Page 30
    WARNING: The cables and ports on the back of the power-supply unit are color-coded to indicate the different power wattage. Ensure that you plug in the cable to the correct port. Failure to do so may result in damaging the power-supply unit and/or system components. About this task The following
  • Dell Alienware Aurora R11 | Service Manual - Page 31
    Steps 1. Place the power supply on the chassis. 2. Align the screw holes on the power-supply unit with the screw holes on the chassis. 3. Replace the four screws (#6-32) that secure the power-supply unit to the chassis. 4. Lift and rotate the power-supply unit cage away from the chassis 5. Connect
  • Dell Alienware Aurora R11 | Service Manual - Page 32
    About this task The following images indicate the location of the power-supply unit and provides a visual representation of the removal procedure. Steps 1. Remove the two screws (#6-32) that secure the power-supply unit bracket to the power-supply unit cage. 2. Lift the power-supply unit bracket off
  • Dell Alienware Aurora R11 | Service Manual - Page 33
    About this task The following images indicate the location of the power-supply unit and provides a visual representation of the installation procedure. Steps 1. Place the power supply on the chassis. 2. Align the screw holes on the power-supply unit with the screw holes on the chassis. 3. Replace
  • Dell Alienware Aurora R11 | Service Manual - Page 34
    Right tron-light board Removing the right tron-light board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the left-side cover. 3. Remove the top-cover. 4. Remove the right-side cover. About this task The following images indicate the location of the right
  • Dell Alienware Aurora R11 | Service Manual - Page 35
    Installing the right tron-light board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the right tron-light board and provides a visual representation of the
  • Dell Alienware Aurora R11 | Service Manual - Page 36
    Processor liquid-cooling assembly Removing the processor liquid-cooling assembly Prerequisites 1. Follow the procedure in Before working inside your computer. WARNING: Despite having a plastic shield, the processor liquid-cooling assembly may be very hot during normal operation. Ensure that it had
  • Dell Alienware Aurora R11 | Service Manual - Page 37
    Steps 1. Lay the computer on the right side. 2. Press the releasing clip on the power-cable connectors and disconnect the power cables from the graphics card. 3. Slide the power-supply unit cage release latches to the unlock position. 4. Lift the power-supply unit cage. 5. Rotate the power-supply
  • Dell Alienware Aurora R11 | Service Manual - Page 38
    Installing the processor liquid-cooling assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. CAUTION: Incorrect alignment of the processor liquid-cooling assembly can damage the system board and processor. About this
  • Dell Alienware Aurora R11 | Service Manual - Page 39
    Steps 1. Slide the radiator and fan assembly into the radiator and fan cage. NOTE: Ensure that the hoses are facing the front of the system 2. Align the screw holes on the processor cooler with the screw holes on the system board. 3. Align the screw holes of the VR heat sink with the screw holes on
  • Dell Alienware Aurora R11 | Service Manual - Page 40
    working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Removing the coin-cell battery resets the BIOS
  • Dell Alienware Aurora R11 | Service Manual - Page 41
    Steps 1. Lay the computer on the right side. 2. Press the releasing clip on the power-cable connectors and disconnect the power cables from the graphics card. 3. Slide the power-supply unit cage release latches to the unlock position. 4. Lift the power-supply unit cage and rotate the power-supply
  • Dell Alienware Aurora R11 | Service Manual - Page 42
    Steps 1. Insert a new coin-cell battery (CR2032) into the battery socket with the positive side facing up, and snap the battery into place. 42
  • Dell Alienware Aurora R11 | Service Manual - Page 43
    2. Rotate the power-supply unit cage towards the chassis. 3. Connect the power cables to the graphics card. 4. Slide the power-supply unit cage release latches towards the locked position. Next steps 1. Install the left-side cover. 2. Follow the procedure in After working inside your computer.
  • Dell Alienware Aurora R11 | Service Manual - Page 44
    Steps 1. Lay the computer on the right side. 2. Press the releasing clip on the power-cable connectors and disconnect the power cables from the graphics card. 3. Slide the power-supply unit cage release latches to the unlock position. 4. Lift the power-supply unit cage and rotate the power-supply
  • Dell Alienware Aurora R11 | Service Manual - Page 45
    Steps 1. Ensure that the securing clips are extended away from the memory-module slot. 45
  • Dell Alienware Aurora R11 | Service Manual - Page 46
    2. Align the notch on the memory module with the tab on the memory-module slot. 3. Insert the memory module into the memory-module slot and press the memory module down until it snaps into position and the securing clips lock in place. CAUTION: To prevent damage to the memory module, hold the memory
  • Dell Alienware Aurora R11 | Service Manual - Page 47
    Steps 1. Remove the screw (M2x2.5) that secures the solid-state drive to the system board. 2. Slide and lift the solid-state drive off the system board. Installing the solid-state drive Prerequisites If you are replacing a component, remove the existing component before performing the installation
  • Dell Alienware Aurora R11 | Service Manual - Page 48
    Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive slot. 2. Insert the solid-state drive at a 45-degree angle into the system board. 3. Press the other end of the solid-state drive down and replace the screw (M2x2.5) that secure the solid-state drive to the
  • Dell Alienware Aurora R11 | Service Manual - Page 49
    49
  • Dell Alienware Aurora R11 | Service Manual - Page 50
    Steps 1. Lay the computer on the right side. 2. Press the releasing clip on the power-cable connectors and disconnect the power cables from the graphics card. 3. Slide the power-supply unit cage release latches to the unlock position. 4. Lift the power-supply unit cage and rotate the power-supply
  • Dell Alienware Aurora R11 | Service Manual - Page 51
    51
  • Dell Alienware Aurora R11 | Service Manual - Page 52
    Steps 1. Place the card into the X16 slot and press down firmly until the graphics card snaps into place. 2. Connect the power cables to the graphics card. 3. Slide the tab on the graphics-card bracket into the slot on the chassis and rotate it into place. 4. Rotate the power-supply unit cage
  • Dell Alienware Aurora R11 | Service Manual - Page 53
    About this task The following images indicate the location of the graphics card and provides a visual representation of the removal procedure. 53
  • Dell Alienware Aurora R11 | Service Manual - Page 54
    Steps 1. Lay the computer on the right side. 2. Press the releasing clip on the power-cable connectors and disconnect the power cables from the graphics card. 3. Slide the power-supply unit cage release latches to the unlock position. 4. Lift the power-supply unit cage and rotate the power-supply
  • Dell Alienware Aurora R11 | Service Manual - Page 55
    Installing the dual-graphics card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the graphics card and provides a visual representation of the installation
  • Dell Alienware Aurora R11 | Service Manual - Page 56
    56
  • Dell Alienware Aurora R11 | Service Manual - Page 57
    Steps 1. Align the graphics card with the slot on the system board. 2. Place the card into the x16/x8 slot and press down firmly until the graphics card snaps into place. 3. Place the card into the x8 slot and press down firmly until the graphics card snaps into place. 4. Connect the power cables to
  • Dell Alienware Aurora R11 | Service Manual - Page 58
    3. Remove the top-cover. 4. Remove the right-side cover. 5. Remove the single-graphics card or dual-graphics card, as applicable. About this task The following images indicate the location of the front bezel and provides a visual representation of the removal procedure. 58
  • Dell Alienware Aurora R11 | Service Manual - Page 59
    59
  • Dell Alienware Aurora R11 | Service Manual - Page 60
    from the chassis. 6. Disconnect the USB cables, LED controller cable and audio cable from the system board and remove the cables from the routing guides on the inside of the chassis. 7. Place the computer in an upright position. 8. Rotate the power-supply unit cage towards the chassis. 9. Rotate and
  • Dell Alienware Aurora R11 | Service Manual - Page 61
    About this task The following images indicate the location of the front bezel and provides a visual representation of the installation procedure. 61
  • Dell Alienware Aurora R11 | Service Manual - Page 62
    62
  • Dell Alienware Aurora R11 | Service Manual - Page 63
    63
  • Dell Alienware Aurora R11 | Service Manual - Page 64
    to the chassis. 4. Connect the USB cables, LED controller cable and audio cable to the system board and route the cables through the routing guides on the inside of the chassis. 5. Place the computer in an upright position. 6. Rotate the power-supply unit cage towards the chassis. 7. Connect the
  • Dell Alienware Aurora R11 | Service Manual - Page 65
    Top bezel Removing the top bezel Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the left-side cover. 3. Remove the top cover. 4. Remove the right-side cover. 5. Remove the wireless card. 6. Remove the front bezel. About this task The following images indicate
  • Dell Alienware Aurora R11 | Service Manual - Page 66
    Installing the top bezel Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the top bezel and provides a visual representation of the installation procedure. Steps
  • Dell Alienware Aurora R11 | Service Manual - Page 67
    6. Follow the procedure in After working inside your computer. Bottom cover Removing the bottom cover Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the left-side cover. 3. Remove the top cover. 4. Remove the right-side cover. 5. Remove the 2.5-inch hard-
  • Dell Alienware Aurora R11 | Service Manual - Page 68
    Installing the bottom cover Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the bottom cover and provides a visual representation of the installation procedure.
  • Dell Alienware Aurora R11 | Service Manual - Page 69
    Processor fan and heat-sink assembly Removing the processor fan and heat-sink assembly Prerequisites 1. Follow the procedure in Before working inside your computer. NOTE: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you touch it.
  • Dell Alienware Aurora R11 | Service Manual - Page 70
    Steps 1. Lay the computer on the right side. 2. Press the releasing clip on the power-cable connectors and disconnect the power cables from the graphics card. 3. Slide the power-supply unit cage release latches to the unlock position. 4. Lift the power-supply unit cage and rotate the power-supply
  • Dell Alienware Aurora R11 | Service Manual - Page 71
    71
  • Dell Alienware Aurora R11 | Service Manual - Page 72
    Steps 1. Place the processor fan and heat-sink assembly on the processor. 2. Align the captive screws on the processor fan heat-sink assembly with the screw holes on the system board. 3. In sequential order, tighten the four captive screws that secure the processor fan and heat-sink assembly to the
  • Dell Alienware Aurora R11 | Service Manual - Page 73
    About this task The following images indicate the location of the processor and provides a visual representation of the removal procedure. Steps 1. Press the release lever down and then push it away from the processor to release it from the tab. 2. Extend the release lever completely and open the
  • Dell Alienware Aurora R11 | Service Manual - Page 74
    Steps 1. Ensure that the release lever on the processor socket is fully extended and the processor cover is fully open. CAUTION: Position the processor correctly in the processor socket to avoid permanent damage to the processor. 2. Align the pin-1 corner on the processor with the pin-1 corner on
  • Dell Alienware Aurora R11 | Service Manual - Page 75
    Steps 1. Remove the screw (M2x2.5) that secures the wireless card to the system board. 2. Lift the wireless-card bracket off the wireless card. 3. Disconnect the antenna cables from the wireless card. 4. Slide and remove the wireless card from the wireless-card slot. Installing the wireless card
  • Dell Alienware Aurora R11 | Service Manual - Page 76
    Steps 1. Connect the antenna cables to the wireless card. The following table provides the antenna-cable color scheme for the wireless card supported by your computer. Table 3. Antenna-cable color scheme Connectors on the wireless card Antenna-cable color Main (white triangle) White Auxiliary
  • Dell Alienware Aurora R11 | Service Manual - Page 77
    procedure. Steps 1. Remove the four screws (M3x4t) that secures the antennas to the top bezel. 2. Remove the antenna cables from the routing guides on the top bezel. 3. Lift the antenna off the top bezel. Installing the antennas Prerequisites If you are replacing a component, remove the existing
  • Dell Alienware Aurora R11 | Service Manual - Page 78
    antenna to the chassis. 2. Replace the four screws (M3x4t) that secures the antennas to the chassis. 3. Route the antenna cables through the routing guides on the top bezel. Next steps 1. Install the front bezel. 2. Install the wireless card. 3. Install the right-side cover. 4. Install the top-cover
  • Dell Alienware Aurora R11 | Service Manual - Page 79
    Steps 1. Remove the four screws (M3x4) that secures the front I/O-panel to the front bezel. 2. Remove the cable from the routing guides on the front I/O-panel. 3. Press the two clips and lift the front I/O-panel off the front bezel. Installing the front I/O-panel Prerequisites If you are
  • Dell Alienware Aurora R11 | Service Manual - Page 80
    screw holes on the front I/O-panel with the screw holes on the front bezel and snap it into place. 2. Route the cables through the routing guides on the front I/O-panel. 3. Replace the four screws (M3x4) that secures the front I/O-panel to the front bezel. Next steps 1. Install the front bezel
  • Dell Alienware Aurora R11 | Service Manual - Page 81
    Steps 1. Disconnect the front-chassis fan cable from the system board. 2. Push the tab to release the front-chassis fan from the chassis. 3. Slide and lift the front-chassis fan off the chassis. Installing the front-chassis fan Prerequisites If you are replacing a component, remove the existing
  • Dell Alienware Aurora R11 | Service Manual - Page 82
    Steps 1. Align the tabs on the front-chassis fan with the slots on the chassis and slide the fan until it snaps into position. 2. Connect the front-chassis fan cable to the system board. Next steps 1. Install the single-graphics card or dual-graphics card, as applicable. 2. Install the left-side
  • Dell Alienware Aurora R11 | Service Manual - Page 83
    Steps 1. Lay the computer on the right side. 83
  • Dell Alienware Aurora R11 | Service Manual - Page 84
    top-chassis fan cable from the system board. 7. Remove the top-chassis fan from the chassis. 8. Remove the top-chassis fan cable from the routing guide on the top-chassis fan bracket. 9. Push the rubber grommets through the holes at each corner of the fan to release top-chassis fan from
  • Dell Alienware Aurora R11 | Service Manual - Page 85
    snap into place. 4. Replace the screw (#6-32) that secures the top-chassis fan to the chassis. 5. Route the top-chassis fan cable through the routing guide on the bracket. 6. Align the tabs on the top-chassis fan with the slots on the chassis and slide the fan until it snaps into
  • Dell Alienware Aurora R11 | Service Manual - Page 86
    Front AlienFX LED boards Removing the front AlienFX LED board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the left-side cover. 3. Remove the right-side cover. 4. Remove the top-cover. 5. Remove the front bezel. About this task The following images indicate
  • Dell Alienware Aurora R11 | Service Manual - Page 87
    Steps 1. Align the screw hole of the AlienFX LED board to the screw hole on the front bezel. 2. Replace the four screws (M3x4) that secure the AlienFX LED board to the front bezel. 3. Connect the AlienFX LED board cable from a Y-cable. Next steps 1. Install the front bezel. 2. Install the top-cover.
  • Dell Alienware Aurora R11 | Service Manual - Page 88
    Steps 1. Remove the two screws (M2x4) that secure the power-button module to the front bezel. 2. Lift the power-button module off the front bezel. 3. Disconnect the cables from the power-button module. Installing the power-button board Prerequisites If you are replacing a component, remove the
  • Dell Alienware Aurora R11 | Service Manual - Page 89
    board Removing the system board Prerequisites 1. Follow the procedure in Before working inside your computer. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board
  • Dell Alienware Aurora R11 | Service Manual - Page 90
    8. Remove the processor. About this task The following images indicate the location of the system board and provides a visual representation of the removal procedure. 90
  • Dell Alienware Aurora R11 | Service Manual - Page 91
    Steps 1. Disconnect all the cables connected to the system board. NOTE: Note the routing of all cables as you remove them so that you can route them correctly after you replace the system board. For information on system-board connectors, see "system-board components". 2. Remove the eight screws
  • Dell Alienware Aurora R11 | Service Manual - Page 92
    92
  • Dell Alienware Aurora R11 | Service Manual - Page 93
    program. You must make the appropriate changes again after you replace the system board. Entering the Service Tag in the BIOS setup program Steps 1. Turn on or restart your computer. 2. Press F2 when the Dell logo is displayed to enter the BIOS setup program. 3. Navigate to the Main tab and enter
  • Dell Alienware Aurora R11 | Service Manual - Page 94
    Next steps NOTE: Service tag is the alphanumeric identifier located at the back side of your computer. 94
  • Dell Alienware Aurora R11 | Service Manual - Page 95
    2. Go to www.dell.com/support. 3. Enter the Service Tag of your computer, and then click Submit. NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model. 4. Click Drivers & downloads. 5. Click the Detect Drivers button. 6. Review and agree to
  • Dell Alienware Aurora R11 | Service Manual - Page 96
    2. Go to www.dell.com/support. 3. Enter the Service Tag of your computer, and then click Submit. NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model. 4. Click Drivers & downloads. 5. Click the Detect Drivers button. 6. Review and agree to
  • Dell Alienware Aurora R11 | Service Manual - Page 97
    2. Go to www.dell.com/support. 3. Enter the Service Tag of your computer, and then click Submit. NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model. 4. Click Drivers & downloads. 5. Click the Detect Drivers button. 6. Review and agree to
  • Dell Alienware Aurora R11 | Service Manual - Page 98
    2. Go to www.dell.com/support. 3. Enter the Service Tag of your computer, and then click Submit. NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model. 4. Click Drivers & downloads. 5. Click the Detect Drivers button. 6. Review and agree to
  • Dell Alienware Aurora R11 | Service Manual - Page 99
    information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive. • Change the system configuration drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can: • Access System Setup by pressing F2 key • Bring
  • Dell Alienware Aurora R11 | Service Manual - Page 100
    the BIOS version number. Displays the product name. Default: Alienware Aurora R11 Displays the service tag of your computer. Displays the asset tag of your Key Wake Up by Integrated LAN AC Recovery Deep Sleep Control USB Wake Support (S3) USB PowerShare (S4/S5) Allows you to enable or disable
  • Dell Alienware Aurora R11 | Service Manual - Page 101
    Advanced USB PowerShare Wake Support (S4/S5) Auto Power On Auto Power On Mode Auto the processor flex ratio and voltage in the Customization mode. Allows you to enable or disable the Computrace service using the Absolute software. Allows you to set the core ratio limit. Allows you to select single
  • Dell Alienware Aurora R11 | Service Manual - Page 102
    Boot Enable USB Boot Support Load Legacy OPROM Boot Option Priorities Boot Option #1 Boot Option #2 Boot Option #3 Table 8. System setup options-Exit menu Save & Exit Save Changes and Reset Discard
  • Dell Alienware Aurora R11 | Service Manual - Page 103
    3. Wait for 5 seconds. 4. Remove the jumper plug from pins 216 and replace it on pins 217. 5. Connect the system-board power cable to the system board. Next steps 1. Remove the left-side cover. 2. Follow the procedure in After working inside your computer. Clearing forgotten password Prerequisites
  • Dell Alienware Aurora R11 | Service Manual - Page 104
    website to troubleshoot and fix your computer when it fails to boot into their primary operating system due to software or hardware failures. For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at www.dell.com/ support. Flashing BIOS (USB
  • Dell Alienware Aurora R11 | Service Manual - Page 105
    dell.com/support. 3. Click Product support, enter the Service Tag of your computer, and then click Submit. NOTE: If you do not have the Service Tag, use the auto-detect feature or manually -click the BIOS update file icon and follow the instructions on the screen. WiFi power cycle About this task
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
Alienware Aurora R11
Service Manual
Regulatory Model: D23M
Regulatory Type: D23M002