Dell CR100 Specifications
Dell CR100 Manual
 |
View all Dell CR100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell CR100 manual content summary:
- Dell CR100 | Specifications - Page 1
Dell System 310/310R Specifications Processor • Intel 80386/20 Memory • 1MB standard, expands to 16MB I/O Expansion Slots • 2-8 bit and Power Supply • 200 watts Diagnostics • Normal Post Diags performed on Power UP of system. • Instead of Dell system support diskette use QAPlus/FE. • Troubleshoot - Dell CR100 | Specifications - Page 2
power cord from the outlet and system 3. Disconnect all peripheral devices from the computer System Cover How to remove the cover: 1. Unlock the security key lock 2. Remove 3 screws on each side of the cover 3. Pull the cover towards the front of the system Field Replaceable Units Memory OEM Part - Dell CR100 | Specifications - Page 3
Video 7 VGA w/ Dell BIOS CGA/Mono PVC2 Part 22H3550 22H3551 22H3564 OEM Part 40012 40471 41755 40470 42087 43263 43352 42061 IBM Part 49H0670 49H0846 49H1390 49H0845 49H1509 66H9848 66H9849 49H1504 OEM Part 40403 20409 29801 22300 IBM Part 22H3458 48H7821 22H2822 22H2823 IBM Document: Dell
-
1 -
2 -
3
 |
 |
Dell
System 310/310R
IBM Document: Dell
02/97 Doc # MT00-014
Page 1 of 3
Copyright International Business Machines, 1997
All rights reserved
Dell System 310/310R
Specifications
Processor
•
Intel 80386/20
Memory
•
1MB standard, expands to 16MB
I/O Expansion Slots
•
2-8 bit and 6-16 bit expansion slots
Diskette Drive
•
•
1.2MB diskette drive
Integrated Features
•
•
Parallel, 2-serial, keyboard, VGA, speaker
Internal Expansion Bays
•
2-user accessible bays, 2-internal bays
I/O Architecture
•
•
Industry Standard Architecture ISA
Power Supply
•
200 watts
Diagnostics
•
Normal Post Diags performed on Power UP of system.
•
Instead of Dell system support diskette use QAPlus/FE.
•
•
Troubleshoot according to errors found during test
CMOS Access
•
QAPlus/FE
Tools and Software Requirements
•
Flat bladed screwdriver
•
Needle nose pliers
•
Anti-static wrist strap
•
•
Diagnostics and formatted blank diskettes
Jumper Settings WD1003-WA2 Card
Jumper
Function
E2 -E3*
Selects primary addresses
E5-E6*
Selects primary addresses
E1-E2
Selects secondary address
E4-E5
Selects secondary address
E7-E8
BIOS selects data transfer rate, controller
supports all data rates
E8-E9
300Kbps data rate not supported, controller
automatically switches to 250Kbps when
300Kbps rate is selected
* Do not remove primary address jumpers unless the OS is
configured to accept two hard disk drive controllers.
Jumper Settings WD1007A-WA2/WAH Card
WA2
Jmpr
Pin
WAH
Jmpr
Pin
Function
W1
2-3
W1
2-3
BIOS addr (C8000-
C9FFF)
W2
2-3
W2
2-3
BIOS addr (C8000-
C9FFF)
W3
jmpr
W3
jpr
BIOS shadow RAM on
W4
no jpr
Dsktte drv cntrlr on
W5
no jpr
single spindle speed on
W6
2-3
Dsktte drv addr (3FX)
W7
1-2
Dsktte drv type
W8
no jpr
W8
no jpr
WD1007 mode
W9
no jpr
W9
no jpr
Chassis not connected
W10
no jpr
W10
no jpr
Digital input unlatched
W11
jpr
W11
no jpr
Dsktte change on
W12
no jpr
W12
no jpr
Secondary addr (1FX)
W13
uncut
Dsktte drv cntrlr on etch
W14
no jpr
W14
no jpr
Sector translation on
W15
no jpr
W15
no jpr
ECC length (4 bytes)
Note:
WD1007A-WA2 supports up to 2 diskettes & 2 hard
drives. The WD1007A-WAH supports up to 2 hard drives.
Address Select
Jumper Settings WD1003-WAH/WA2 Card
W1
W2
W3
Function
2-3
2-3
Jumper
BIOS addr. C8000-C9FFF
2-3
1-2
Jumper
BIOS addr. CA000-CBFFF
1-2
2-3
Jumper
BIOS addr. CC000-CDFFF
1-2
1-2
Jumper
BIOS addr. CE000-CFFFF
W6
1-2
diskette range 37X
2-3
diskette range 3FX
W12
No jpr
Pri/Sec HD addr 1FX
Jumper
Pri/Sec HD addr 17X