Dell Force10 E1200i E1200i ExaScale Installation Guide
Dell Force10 E1200i Manual
View all Dell Force10 E1200i manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell Force10 E1200i manual content summary:
- Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 1
E1200i ExaScale Installation Guide - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 2
damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Information in this publication is subject to change without notice. © 2010 Dell Force10. All rights reserved. Reproduction of these materials - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 3
Unpacking the E1200 System 23 Installing the Equipment Rack Shelf Bar 24 Standard Front Chassis Mounting 24 Installing the Chassis into an Equipment Cabinet 26 6 Installing Fan Trays 7 Installing AC Power Supplies Securing the Chassis Ground 30 Installing Power Supplies 30 AC Power Supply and - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 4
dell.com | support.dell Line Card LEDs 48 Installing Switch Fabric Modules (SFM3s 48 AC Power Supplies 60 Remove an AC Power Supply in a non-redundant installation 61 Remove an AC Power Supply in a redundant installation 61 Removing and Replacing DC Power Supplies 61 Remove a DC Power Supply - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 5
Prompt 71 B Alarms Power Supplies Alarms 78 AC Power Supplies and Alarms 78 SFM3s and Alarms 79 C System Specifications E1200i AC Chassis Physical Design 81 E1200i AC System Power Requirements 82 E1200i DC Chassis Physical Design 82 E1200i DC System Power Requirements 82 Environmental - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 6
www.dell.com | support.dell.com 6 | Contents - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 7
Guide This guide provides site preparation recommendations, step-by-step procedures to rack mount the Force10 Networks E1200 ExaScale chassis, as well as instructions to install its fan trays, power supplies, route processor modules (RPMs), switch fabric modules (SFM3s), and line cards. The E1200 - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 8
www.dell.com | support.dell.com WARNING: Leakage Current (High Touch Current) in AC-powered systems: AC power cords are secured to the power inlet using the provided brackets. The power cord plugs must be secured to the building outlets by the qualified chassis installer or a qualified electrician. - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 9
The Dell Force10 E1200 system is a carrier-class, high-capacity aggregation router. The 16-slot modular system provides two slots dedicated for Route Processor Modules (RPMs) and 14 slots for line cards with Layer 2 switching and Layer 3 and routing capabilities. Operating Overview The E1200 system - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 10
www.dell.com | support.dell.com Figure 2-1. E1200i AC Chassis Front View Cable Management System Line Card Slots RPMs 10 | The E1200 System Switch Fabric Modules (SFM3s) Blanks (BLNK) Air Filter Air Vents AC Power Supplies AC Power Plugs - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 11
Figure 2-2. E1200 AC Chassis Rear View Installed Fan Tray Locking Screw Empty Fan Tray (with self-closing door) Ground Connection The E1200 System | 11 - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 12
www.dell.com | support.dell.com Figure 2-3. E1200i DC Chassis Front View Cable Management System Line Card Slots RPMs 12 | The E1200 System Switch Fabric Modules (SFM3s) DC Power Supply Air Filter Air Vents - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 13
with self-closing door) Ground Connection Table 2-1. E1200 Hardware Component Operating Requirements Summary Component Backplane (factory installed) Air filter (factory installed) Fan trays RPMs Line cards SFM3s AC Power Supply DC Power Supply Cable management system Cable management system cover - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 14
Test DC Power Supply and Fan Operability Test 7 Install card components: • RPM(s) and line cards • SFM3s Installing Line Cards and RPMs Installing Switch Fabric Modules (SFM3s) 8 Connect network cable RPM Ports and Cables 9 Supply power to the chassis Supplying Power - AC Supplying Power - DC - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 15
-controlled room, away from nearby heat sources such as hot air vents or direct sunlight. • Away from sources of severe electromagnetic noise. • Near an adequate power source. Connect the E1200 to the appropriate branch circuit protection as defined by local electrical codes. • Means of - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 16
at the chassis front to access the air filter, power supplies, and cards. Power The E1200 requires 3 AC Power Supplies in a shelf (0, 1, 2 or 3, 4, 5) or 1 DC PEM to operate. For full redundancy, you must have 6 AC Power Supplies (so that if one power supply fails in one shelf, the system remains - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 17
line card slots. Always replace empty slots with blank panels. Each E1200 system requires at least three AC Power Supplies or at least one DC Power Supply to operate. Three AC units are required for power supply redundancy, and so six AC units provides full redundancy. Two DC units are required for - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 18
www.dell.com | support.dell.com • Non-condensing relative humidity should be maintained within 5 to 95 percent. • Store on a dry floor, away from direct sunlight, heat, and air conditioning ducts. • Store in a dust-free environment. 18 | Site Preparation - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 19
rack. Do not unpack the power supplies, fan trays, air filter, or cards until the chassis is installed. WARNING: The E1200 AC shipping containers each weigh up component (fan trays, power supplies, line cards, RPMs, SFM3s, cables). To prevent bodily injury when mounting or servicing this unit in a - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 20
dell.com | support.dell.com Installing the Equipment Rack Shelf Bar The rack shelf bar (Figure 4-1) enables you to easily position the chassis into the rack and provides the unit additional stability. The E1200 install the stabilizers before mounting or servicing the unit in the rack. AC Chassis - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 21
Gestell anbringen oder sie warten. NOTE: Dell Force10 recommends that you install and operate the E1200 system in a standard 19-inch or 23inch equipment rack. Install the E1200 system after you secure the equipment rack and tighten to secure the chassis in the rack. Installing the AC Chassis | 21 - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 22
www.dell.com | support.dell.com Installing the Chassis into an Equipment Cabinet Install the E1200 system after you secure the rack shelf bar. Load the chassis in the lower half of Insert the remaining mounting screws and tighten to secure the chassis in the cabinet. 22 | Installing the AC Chassis - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 23
instructions to rack mount your E1200 system into a standard 19-inch or 23-inch equipment rack. It contains the following sections: • Unpacking the E1200 Do not unpack the power supplies, fan trays, air filter, or cards until the chassis is installed. WARNING: The E1200 DC shipping containers each - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 24
dell.com | support.dell.com Installing the Equipment Rack Shelf Bar The rack shelf bar (Figure 5-1) enables you to easily position the chassis into the rack and provides the unit additional stability. The E1200 , install the stabilizers before mounting or servicing the unit in the rack. WARNING: - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 25
zu installieren, bevor Sie die Einheit im Gestell anbringen oder sie warten. NOTE: Dell Force10 recommends that you install and operate the E1200 system in a standard 19-inch or 23inch equipment rack. Install the E1200 system after you secure the equipment rack shelf bar. Load the chassis in the - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 26
www.dell.com | support.dell.com Installing the Chassis into an Equipment Cabinet Install the E1200 system after you secure the rack shelf bar. Load the chassis in the lower half of the cabinet to avoid it becoming top-heavy. Make - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 27
operation, do not operate the chassis with only one fan tray for more than 30 minutes. WARNING: Install the fan trays before you supply power to the system. WARNING: Electrostatic discharge (ESD) damage can occur when components are mishandled. Always wear an ESD-preventative wrist or foot-heal - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 28
dell.com Figure 6-2. Fan Tray screw latch Install the fan trays after the chassis is installed securely in the equipment rack. Access the fan tray slots from the rear side of the chassis. To ensure proper temperature and airflow control, all six fan trays must be installed before you supply power - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 29
the LEDs will indicate status while the On/Standby switch is in Standby. Figure 7-1. E1200i AC Power Supply Shelf Power Supplies On/Standby Switch AC-Cord Retainer Safety Cover AC-0 AC-1 AC-2 AC-3 AC-4 AC-5 AC-0 AC-3 AC-1 AC-4 AC-2 AC-5 WARNING - HIGH LEAKAGE CURRENT. EARTH CONNECTION - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 30
Stromzufuhren abgetrennt sein. The following are Dell Force10 supplied plug types. All power plugs must comply with local codes. Check with your Dell Force10 representative to purchase cords or plugs for your system. • EU: CEE 7/7 • UK: CEE7/7 • SWZ: CEE7/7, 309 30 | Installing AC Power Supplies - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 31
On/Standby switch, located on the left side of plug AC-0, is in the Standby (up) position (Figure 7-1). 2 Loosen the cord retainers locking screws (if needed) and tilt the AC-cord retainer up approximately 15o and gently slide the cover away from the chassis. 3 Slide the power supplies into - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 32
www.dell.com | support.dell.com • The AC-cord Retainer is secured over the plugs. WARNING: Prevent exposure and contact with hazardous voltages. Do not attempt to operate this system without the AC-cord Retainer. • Your power cables connect to an appropriate AC power supply in a manner that - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 33
and Fan Tray LEDs Table 7-1. Power Supply LEDs Status No AC power Operational (On/Standby switch may be set to Standby) Power Supply Failure Table 7-2. Fan Tray LEDs Status Booting Fault Detected Communication Failure Operational Loss of Power LED is ... Unlit: No connection Lit: GREEN Lit: AMBER - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 34
34 | Installing AC Power Supplies www.dell.com | support.dell.com - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 35
SF4L-SFMC Force10 Networks Force10 Networks Force10 Networks Force10 Networks Force10 Networks Force10 Networks Force10 Networks Force10 Networks Force10 Networks online 8-2 is used in both the E1200 and E1200i DC chassis. Figure 8-2. E1200i DC PEM FN00101lp Installing DC Power Supplies | 35 - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 36
.dell.com | support.dell.com Figure 8-3. E1200 PEM Front Panel Studs PEM interlock lever Latch Release Status -48/-60Vdc 150A, 7200VA CC-E1200-PWR-DC Over-current protector FN00102lp Locking screws Cable and Connector Requirements You must provide your own cables to connect to a remote power - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 37
Vdc Use the following steps to install a DC PEM: Step Task 1 Make sure that the remote power source (the circuit breaker panel) is in the OFF position. 2 Make sure that the over-current . Over current protector PEM interlock lever Locking screws fn00104lp Installing DC Power Supplies | 37 - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 38
dell.com | support.dell . Figure 8-4. Cable Connector Required for E1200 PEM All meas urements s hown in the remote power sources (circuit breakers A and B). a Check that the remote power sources (for color to comply with local electrical codes. NOTE: Power cables must be terminated only with a UL- - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 39
. Figure 8-5. Connecting the Ground Cable to the E1200 PEM Lug Split-lock washer Lug nuts Ground studs fn00106lp Figure 8-6. DC PEM with Connections in Place -48 (-) cable typically black Ground cable typically green Return cable (+) typically red fn00106lp Installing DC Power Supplies | 39 - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 40
. DC Power Supply and Fan Operability Test After you have completed the fan tray and PEM installation, verify their operability by supplying power to the chassis and verifying the status LEDs. NOTE: If there is a DC PEM failure, the entire PEM must be replaced. There are no field-serviceable parts - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 41
or is blinking amber after the system has booted, replace the power supply. 3 Both fan tray LEDs should be green (online). blinking green fan tray LED indicates that the system is booting. During boot, the blinking green LED may switch to blinking amber until the RPM boot is complete. If a fan - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 42
42 | Installing DC Power Supplies www.dell.com | support.dell.com - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 43
, and line cards on an antistatic surface. WARNING: Do not supply power to your E1200 system until the power supplies and fan tray(s) are installed and verified, and RPMs, SFM3s, line cards, and any blank panels are installed. Force10 Networks recommends that you keep all components in the original - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 44
www.dell.com | support.dell.com RPMs The E1200 system requires the installation of at least one RPM, although two are recommended for redundancy. RPMs are designed to be installed in either the center R0 or R1 slots. Since FTOS searches for an RPM in slot 0 first, Dell Force10 recommends you - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 45
to ensure that all chassis slots are installed with operational modules or blanks. Preparing and Installing RPMs and Line Cards Installing an RPM into the E1200i RPMs, line cards, and blank panels are packaged in the same box. To prolong the life of the EMI seals, begin installing cards in the - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 46
www.dell.com | support.dell.com Figure 9-2. Installing Cards into the E600 Figure 9-3. RPM and Line Card Slot Numbering Label Slot CAUTION: It is important that you retain the packaging - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 47
from the anti-static packaging. Align the RPM with the guide and gently slide it into the slot until you feel the a second RPM either before the system is powered on or after the Primary RPM is up and the routing and switching functions for the entire E600/E1200 system. The E600/E1200 operates with a - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 48
www.dell.com | support.dell.com Table condition, a fan tray failure, an overcurrent condition in a power supply, or an out-of-tolerance voltage. The RPM LEDs are controlled meaning. Installing Switch Fabric Modules (SFM3s) A minimum of 8 SFM3s are required in order for the E1200 system to operate - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 49
with the guide and gently power Status Line Card Cable Management Systems Dell Force10 provides a variety of E1200 chassis cable management systems to manage your fiber optic and auxiliary cables connecting to line cards. For details, see the Dell Force10 price list. For installation instructions - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 50
www.dell.com | support.dell.com 50 | Installing RPMs, Line Cards, and SFM3s - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 51
describes standard RPM cables and adapter pin assignments for the E1200i AC and DC systems. It contains the following sections: • monitoring. Modem connections are not supported on this port. • Auxiliary. A UART port with an RJ-45 jack, allows modem access to the E1200 system from a remote location. - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 52
www.dell.com | support.dell.com • Window Terminal Emulator option set to NO • 24 lines X 80 characters • No flow control (console port only) • Hardware flow control (RTS/CTS) (for auxiliary port only) Cable and Adapter Pin Assignments Use the E1200 Console port on the RPM to connect to a terminal - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 53
-45 rollover cable and RJ-45 to DB-25 female DTE adapter. Table 10-4 lists the pin assignments. Table 10-4. Pin Assignments Between E1200 Console and DB-25 Adapter E1200 Console Port Signal RTS DTR TxD GND GND RxD DSR CTS RJ-45 to RJ-45 Rollover Cable RJ-45 Pinout 1 2 3 4 5 6 7 8 RJ - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 54
dell.com | support.dell . Table 10-5. RJ-45 to DB-25 Adapter Pin (Modem) Assignments E1200 Auxiliary Port Signal RTS DTR TxD GND GND RxD DSR CTS RJ-45 order to obtain network access capability, such as as external flash. It provides some amount of power at 5V. The B port is a device port - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 55
Up This chapter provides instructions for powering up your E1200 AC or DC system after you have installed all the chassis components and made your power and network connections. It covers the following topics: • Preparation • Supplying Power - AC • Supplying Power - DC • Booting to the CLI Prompt - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 56
www.dell.com | support.dell.com Supplying Power - AC Step Task 1 Flip the REMOTE power switch to the ON position. 2 Remove the card from the box. Remove the card from the anti-static bag. 3 Flip the On/Standby switch to the ON position. 4 The Status LED for each power supply should be - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 57
long as the system is receiving power and is operational. When you supply power to the E1200 system, the system performs a series of power-on self tests. RPM, line Refer to the FTOS Configuration Guide for initial configuration procedures and configuration instructions. Booting from the BOOT_USER - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 58
58 | Powering Up www.dell.com | support.dell.com - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 59
instructions for removing and replacing E1200 AC and DC components. It covers the following topics: • Removing and Replacing Fan Trays • Removing and Replacing AC Power Supplies • Removing and Replacing DC Power Supplies Insert the fan tray into the chassis. Guide the tray firmly into the slot until - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 60
www.dell.com | support.dell.com Figure 12-1. Securing the Fan Tray Screw Latch screw latch Removing and Replacing AC Power Supplies If you are operating your E1200 AC chassis with redundant Power Supplies, you can install, remove, or replace a Power Supply without affecting system operation. If you - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 61
Remove an AC Power Supply in a non-redundant installation Step Task 1 Unplug the network interface cables connected to the line card or RPM. 2 Activate the disconnect switch at the Main power source or disconnect the AC cord at the remote power source. 3 Grip the handle and squeeze the thumb - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 62
www.dell.com | support.dell.com Remove a DC Power Supply Step Task 1 Ensure that the remote power source is in the OFF position and that the PEM status light is off. • PEM 0 connects to remote power source 0. • PEM 1 connects to remote power source 1. 2 Loosen the retaining screw and remove the PEM - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 63
power or system operations. RPMs, line cards, and SFM3s are hot-swappable. The E1200 remove and replace E1200 line card or RPM modules: Step Task 1 Unplug the network interface cables connected to replacement card, align the new card with the guide, and gently slide the card into the slot until - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 64
dell.com | support.dell , one RPM, and eight SFM3s) you power off your system until the cards are replaced Align the new SFM3 with the guide and gently slide the card into If you are not operating your E1200 system with redundancy, replace the ' status changed and the switch fabric is up appear when - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 65
installed air filter will restrict air flow and will generate thermal problems throughout the chassis. Ensure the air filter is oriented correctly and reading. 3 Guide the filter firmly into the slot until it stops. The E1200 air filter is hot-swappable. You do not need to turn the power off to - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 66
www.dell.com | support.dell.com 66 | Removing and Replacing Components - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 67
card to copy the image and configuration files for storage and backup purposes. For complex configurations, use the copies for other E1200 systems in your network. Configure your boot execution process to use the images stored on a flash card as the primary (active), secondary (standby), or default - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 68
www.dell.com | support.dell.com To install the flash memory card: Step Task 1 Press the flash cards must be formatted in the E1200 before use. Flash cards used on systems other than the E1200 as well as cards formatted on PCs must be reformatted in the E1200 flash slot before they can be used - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 69
slot0: for the external flash. The default is flash: (the internal flash). To view the external flash, enter dir slot0: Figure 13-1. dir Command Example Force10#dir slot0: Directory of slot0: 1 -rwx 6478482 Sep 7 101 16:54:34 E1200i.BIN Using a Flash Memory Card | 69 - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 70
www.dell.com | support.dell.com FTOS supports up to a 40-character file name length, up to a 180-character local file path length, and up to a 256-character remote file path length. 70 | Using a Flash Memory Card - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 71
instructions to boot the E1200 AC and DC system from the BOOT_USER prompt. The System Boot Process System Boot When you supply power to the E1200 system, the system performs a series of power Force10>. The RPM cards in the E1200 . NOTE: The E1200 system supports up to a experience boot problems. This - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 72
www.dell.com | support.dell.com To configure the chassis from the BOOT_USER prompt: Step Command Task 1 help or ? • The BOOT_USER # prompt appears after an autoboot interruption. This is the - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 73
2 18:22:47 US/Pacific 2007 Bootflash Partition B: Force10 Networks System Boot Copyright 1999-2007 Force10 Networks, Inc. ROM Header Version 1.0 Official CP_IMG_BOOT, BSP Release : boot device : flash file name : /E1200i-x.bin SECONDARY OPERATING SYSTEM BOOT PARAMETERS No Operating - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 74
www.dell.com | support.dell.com Step 5 Command boot change {primary | secondary | default} Task ( '.' = clear field; '-' = go to previous field boot device file name : flash : /E1200-3.x.bin BOOT_USER # boot change default '.' = clear field; '-' = go to previous field 74 | System Boot - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 75
management port config show 7 show interface management ethernet • Use the show interface management ethernet command to display the IP address and network mask of the management Ethernet port. interface management ethernet ip address ipaddress ip-address-mask • If the show command output does - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 76
www.dell.com | support.dell.com Step Command Task (continued) BOOT_USER 10778521 FEB-18-2002 22:53:26 name -------e1200-.bin E1200-3.bin E1200-2.bin E1200-3.1.bin 10 reload 11 Force10> Reload software. The autoboot program initializes and displays instructions. 76 | System Boot - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 77
• fan trays status • Power Supply status • fan tray status • power supply status • RPMs status • high temperature on RPMs • line cards status • high temperature on line cards • SFM3s status • high temperature on SFM3s. A major alarm is any fault that would render the E1200 non-functional. A minor - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 78
www.dell.com | support.dell.com Table B-1. Alarm Events and Reporting Module Alarm Event Alarm LED AC Power Hardware failure in a non-redundant power Supplies configuration (3 power supplies) major (red) Hardware failure in a redundant power configuration (4 minor (amber) power supplies) - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 79
, the software generates a major alarm and an SNMP trap, lights the major LED, and activates the audible alarm. When you operate the E1200 with three AC power supplies and six or more line cards, the software lists a redundancy alarm on the console and in the show alarms command output. All line - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 80
80 | Alarms www.dell.com | support.dell.com - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 81
appendix contains two major sections: • E1200i AC Chassis Physical Design • E1200i AC System Power Requirements • E1200i DC Chassis Physical Design • E1200i DC System Power Requirements • Environmental Specifications • Agency Compliance E1200i AC Chassis Physical Design Parameter Specifications - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 82
www.dell.com | support.dell.com E1200i AC System Power Requirements Parameter Nominal Input Voltage Maximum Power Consumption Maximum Thermal Output (5,700 W) Maximum Input Current (per power supply) Maximum System Power Input Specifications 200-240 VAC 50/60 Hz 6,634 Watts 19,449 BTU/hour 15.0 A - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 83
95 percent, noncondensing Bellcore GR-63 Agency Compliance The E1200 is designed to comply with the following safety and agency installed and used in accordance to the instructions, it may cause harmful interference to order to meet FCC emission limits. Dell Force10 is not responsible for any radio - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 84
www.dell.com | support.dell.com Dell Force10, EMEA - Central Dahlienweg 19 66265 Heusweiler Germany http://www.force10networks trouble occurs, the user may be required to take corrective actions. WARNING: AC Power cords are for use with Dell Force10 equipment only. Do not use Dell Force10 AC power - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 85
• CSA 60950-1-03, 1st Edition • EN 60950-1, 1st Edition • EN 60825-1 Safety of Laser Products-Part 1: Equipment Classification Requirements and User's Guide • EN 60825-2 Safety of Laser Products-Part 2: Safety of Optical Fibre Communication Systems • FDA Regulation 21CFR 1040.10 and 1040.11 • IEC - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 86
www.dell.com | support.dell.com • EN 300 386 V1.3.3 (2005) EMC for Network Equipment • EN 55024 1998 +A1:2001 +A2:2003 Product Recycling and Disposal This switch must be recycled or discarded according to applicable local and national regulations. Dell Force10 encourages owners of information - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 87
, technical tips, and white papers • Support Programs: Information on the suite of Dell Force10 support and professional support services. The Support Policies section of iSupport contains the Support Guide, which details the types of information and services that you can access through iSupport and - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 88
Dell Force10 Log in to iSupport at http://www.force10networks.com/support/, and select the Service TAC Request tab. Information to Submit When Opening a Support of show tech-support.) • Console captures showing the error messages • Console captures showing the troubleshooting steps taken • - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 89
support case. Open a support case by: • Using the Create Service Request form on the iSupport page (see Contacting the Technical Assistance Center on page 88). • Contacting Dell Force10 tech-support.) • Console captures showing the error messages • Console captures showing the troubleshooting - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 90
90 | Technical Support www.dell.com | support.dell.com - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 91
(technical support) 87 D Danger 7 DC PEMs cable requirements 36 connector requirements 36 full redundancy 35 minimum requirement 35 remote power source 35 disposal, switch 86 E L Leakage Current 8, 31, 32, 55 LEDs AC power supplies 32, 41 fans 32, 41, 56 In Use LED 68 line card 48 PEM Voltage LED - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 92
31, 40 R rack installing 21, 25 mounting 16 placement 16 recycling, switch 86 removing air filters 65 fan trays 59 line cards 63 Power Supply 62 RPMs 63 SFMs 63, 64 requesting replacement hardware 89 requirements, AC power 29 Route Processor Module (RPM) 9 RPM (Route Processor Module) 9 S safety - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 93
Test, Power Supply and Fan Operability 31, 40 U unpacking 19, 23 W Warning 7 WEEE 86 Index | 93 - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 94
94 | Index www.dell.com | support.dell.com - Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 95
- Dell Force10 E1200i | E1200i ExaScale Installation Guide - Page 96
Printed in the U.S.A. www.dell.com | support.dell.com
E1200i ExaScale
Installation Guide