Dell Force10 E1200i TeraScale to ExaScale Upgrade Procedure
Dell Force10 E1200i Manual
 |
View all Dell Force10 E1200i manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell Force10 E1200i manual content summary:
- Dell Force10 E1200i | TeraScale to ExaScale Upgrade Procedure - Page 1
Supported Hardware Hardware E1200i Chassis (Note 1) AC Power Supply 2800W DC Power Entry Module Route Processor Module-ExaScale Switch Fabric Module (Note 2) 10 port 10GE line card (10M CAM) 10 port 10GE line card (40M CAM) Fan Tray Catalog Number Minimum Software Version Required CH-E1200I-AC CH - Dell Force10 E1200i | TeraScale to ExaScale Upgrade Procedure - Page 2
or Power Supply, Air Filter, Fan Tray are installed and verified, and RPMs, SFMs, and line cards have been installed. • To avoid chassis over-temperature condition, install blanks for RPMs, SFMs, and line card slots not in use. Always replace cards or blanks immediately. ExaScale SFM Requirements - Dell Force10 E1200i | TeraScale to ExaScale Upgrade Procedure - Page 3
on all 5 SFM to version 0x0.0.3 is complete. * * Rebooting chassis .... !!! * Verify the result of the SFM version upgrade using the show sfm command. TeraScale to ExaScale Upgrade Procedure 3 - Dell Force10 E1200i | TeraScale to ExaScale Upgrade Procedure - Page 4
:29: %RPM1-P:CP %TSM-6-SFM_USR_RESET: SFM 0 reset by user reset SFM 0 successful ! * * Warning !!! Warning !!! Warning !!! * * * Resetting on 1 SFM to revision 0x0.0.3 is complete ! * TeraScale to ExaScale Upgrade Procedure 4 - Dell Force10 E1200i | TeraScale to ExaScale Upgrade Procedure - Page 5
this upgrade. Refer to Supported Hardware for the list of hardware required for E-Series ExaScale with FTOS 8.1.1.1. Step 1 2 3 4 5 6 7 8 Command Syntax Turn the On/Standby switch to Standby (AC). Command Mode Purpose Power-off the chassis. Turn the Remote Power Source to Off (DC). Replace - Dell Force10 E1200i | TeraScale to ExaScale Upgrade Procedure - Page 6
Step Command Syntax Command Mode Purpose Force10#show chassis -- Manufacturing Info -- Chassis Type : E600i Chassis Mode : ExaScale Chassis Epoch : 10.4 micro-seconds Chassis MAC : 00:01:e8:41:cb:36 Serial Number : TY000001140 Part Number : 7520023900 Vendor Id : 04 Date Code : 01012008 - Dell Force10 E1200i | TeraScale to ExaScale Upgrade Procedure - Page 7
been modified. Save? [yes/no]: y Proceed with reload [confirm yes/no]:y 2 Turn the On/Standby switch to Standby (AC). Power-off the chassis. Turn the Remote Power Source to Off (DC). 3 Replace the ExaScale RPMs, SFMs and linecards with TeraScale RPMs, linecards and SFMs. Refer to the RPM, SFM - Dell Force10 E1200i | TeraScale to ExaScale Upgrade Procedure - Page 8
Step 8 Command Syntax show chassis Command Mode EXEC Privilege Purpose We can confirm using the show chassis command. Force10#show chassis -- Manufacturing Info -- Chassis Type : E1200 Chassis Mode : TeraScale Chassis Epoch : 10.4 micro-seconds Chassis MAC : 00:01:e8:05:db:05 Serial Number
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
TeraScale to ExaScale Upgrade Procedure
The E-Series TeraScale is easily upgraded to Force10 Networks E-Series ExaScale. These upgrade requirements
outline the necessary components and procedures required to upgrade the E1200i with FTOS version 8.1.1.0.
Direct any questions regarding the upgrade to Force10 Networks’ Customer Support.
E-mail: [email protected]
Web:
www.force10networks.com/support/
Telephone:
US and Canada: 866.965.5800
International: 408.965.5800
Supported Hardware
Hardware
Catalog Number
Minimum Software
Version Required
E1200i Chassis
(Note 1)
CH-E1200I-AC
CH-E1200I-DC
8.1.1.1
AC Power Supply 2800W
CC-E1200I-2800W-AC
8.1.1.1
DC Power Entry Module
CH-E1200I-DC
8.1.1.1
Route Processor Module—ExaScale
LC-EH-RPM
8.1.1.1
Switch Fabric Module
(Note 2)
CC-E-SFM3
8.1.1.1
10 port 10GE line card (10M CAM)
LC-EH-10GE-10S
8.1.1.1
10 port 10GE line card (40M CAM)
LC-EJ-10GE-10S
8.1.1.1
Fan Tray
CC-E-1200I-Fan
8.1.1.1
Note 1:
Do not mix AC and DC power supplies.
Note 2:
E-Series ExaScale systems and FTOS Release 8.1.1.0 requires SFM version 752-00265-03 Rev
01 or higher. Use the
show sfm
command to determine if your SFMs need to be upgraded.
Do not mix SFMs. All the SFMs in the chassis must run the required minimum software version.