Dell Inspiron 15 7510 Service Manual

Dell Inspiron 15 7510 Manual

Get Dell Inspiron 15 7510 PDF manuals and user guides View all Dell Inspiron 15 7510 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell Inspiron 15 7510 manual content summary:

  • Dell Inspiron 15 7510 | Service Manual - Page 1
    Inspiron 15 7510 Service Manual Regulatory Model: P106F Regulatory Type: P106F002 May 2021 Rev. A00
  • Dell Inspiron 15 7510 | Service Manual - Page 2
    of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be
  • Dell Inspiron 15 7510 | Service Manual - Page 3
    computer 6 Safety instructions...6 Working inside your computer...6 Entering Service Mode...8 Exiting Service Mode...9 After working inside your computer...9 Chapter 2: Removing and installing components 10 Recommended tools...10 Screw list...10 Major components of Inspiron 15 7510...11 Base cover
  • Dell Inspiron 15 7510 | Service Manual - Page 4
    an existing system setup password 75 Clearing CMOS settings...75 Clearing BIOS (System Setup) and System passwords 75 Chapter 5: Troubleshooting...76 SupportAssist diagnostics...76 Locate the Service Tag or Express Service Code of your Dell computer 76 System-diagnostic lights...76 4 Contents
  • Dell Inspiron 15 7510 | Service Manual - Page 5
    Recovering the operating system...77 Flashing the BIOS...77 Flashing BIOS (USB key)...78 Backup media and recovery options...78 WiFi power cycle...78 Drain residual flea power (perform hard reset)...79 Chapter 6: Getting help and contacting Dell 80 Contents 5
  • Dell Inspiron 15 7510 | Service Manual - Page 6
    and the contacts. CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions that is shipped with the product or at
  • Dell Inspiron 15 7510 | Service Manual - Page 7
    for shut-down instructions. 3. Disconnect your such as intermittent problems or a shortened Dell products, the sensitivity to static damage is now higher than in previous Dell damage to recognize and troubleshoot is the intermittent (also on. Once deployed properly, service parts can be removed from
  • Dell Inspiron 15 7510 | Service Manual - Page 8
    When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport. Entering Service Mode Service Mode allows users to immediately cut off electricity from the computer and conduct repairs
  • Dell Inspiron 15 7510 | Service Manual - Page 9
    allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the battery cable from the system board. To exit Service Mode: 1. Connect the AC adapter to the power-adapter port on your computer. 2. Press the power button to turn on the computer. Your
  • Dell Inspiron 15 7510 | Service Manual - Page 10
    2 Removing and installing components NOTE: The images in this document may differ from your computer depending on the configuration you ordered. Recommended tools The procedures in this document may require the following tools: ● Phillips screwdriver #0 ● Phillips screwdriver #1 ● Plastic scribe
  • Dell Inspiron 15 7510 | Service Manual - Page 11
    I/O board M2x4 M2x4 M2x4 Touchpad M2x1.8 Touchpad Power-adapter port M2x3 M2.5x5 Display hinges M2.5x5 Quantity 2 1 2 1 1 1 2 5 2 2 4 Screw image Major components of Inspiron 15 7510 The following image shows the major components of Inspiron 15 7510. Removing and installing components 11
  • Dell Inspiron 15 7510 | Service Manual - Page 12
    1. Base cover 2. Heat sink 3. System fan 4. Memory module 5. Power-adapter port 6. Solid-state drive 7. System board 8. Battery 9. Speaker 10. Palm-rest and keyboard assembly 12 Removing and installing components
  • Dell Inspiron 15 7510 | Service Manual - Page 13
    card 14. Solid-state drive 15. I/O board 16. GPU fan 17. Power button with fingerprint reader 18. Power button NOTE: Dell provides a list of components Follow the procedure in Before working inside your computer. 2. Enter Service Mode. About this task The following images indicate the location of
  • Dell Inspiron 15 7510 | Service Manual - Page 14
    Steps 1. Remove the seven (M2x4) screws that secure the base cover to the palm-rest and keyboard assembly. 2. Loosen the two (M2x7.5) captive screws that secure the base cover to the palm-rest and keyboard assembly. 3. Using a plastic scribe, pry the base cover from the U-shaped indents at the top
  • Dell Inspiron 15 7510 | Service Manual - Page 15
    . About this task The following images indicate the location of the base cover and provide a visual representation of the installation procedure. Removing and installing components 15
  • Dell Inspiron 15 7510 | Service Manual - Page 16
    Steps 1. Connect the battery cable. 2. Place the base cover on top of the palm-rest and keyboard assembly. 3. Align the screw holes on the base cover with the screw holes on the palm-rest and keyboard assembly, and then snap the base cover into place. 4. Tighten the two (M2x7.5) captive screws that
  • Dell Inspiron 15 7510 | Service Manual - Page 17
    ● Ensure any screws during the servicing of this product are not lost dell.com or authorized Dell partners and resellers. Removing the battery Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task NOTE: Inspiron 15 7510 also supports
  • Dell Inspiron 15 7510 | Service Manual - Page 18
    Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task NOTE: Inspiron 15 7510 also supports 6-cell (86 Wh) battery. The following image indicates the location of the 3-cell (56 Wh) battery and provides a visual
  • Dell Inspiron 15 7510 | Service Manual - Page 19
    in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. NOTE: If battery is disconnected from system board for service, then there is a delay during system boot as the system undergoes RTC battery reset. About this task The following images indicate the location of
  • Dell Inspiron 15 7510 | Service Manual - Page 20
    Steps 1. Flip the battery and remove the battery cable from the routing guides on the battery. 2. Disconnect the battery cable from the connector on the battery. 3. Lift the battery cable off the battery. Installing the battery cable Prerequisites
  • Dell Inspiron 15 7510 | Service Manual - Page 21
    battery cable on the battery. 2. Route the battery cable through the routing guides on the battery. 3. Connect the battery cable to the connector on the inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task NOTE: Inspiron 15 7510 supports two memory slots. The
  • Dell Inspiron 15 7510 | Service Manual - Page 22
    Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task NOTE: Inspiron 15 7510 supports two memory slots. The following image indicates the location of the memory module and provides a visual representation of the
  • Dell Inspiron 15 7510 | Service Manual - Page 23
    module and reinstall it. NOTE: Repeat step 1 to step 4 to install any other memory modules in your computer. Next steps 1. Install the base cover. 2. Exit Service Mode. 3. Follow the procedure in After working inside your computer. Removing and installing components 23
  • Dell Inspiron 15 7510 | Service Manual - Page 24
    the computer is in sleep or on state. 2. Enter Service Mode. 3. Remove the base cover. About this task NOTE: The M.2 card drive, you will need a mounting bracket (sold separately, please contact Dell support). NOTE: This procedure applies only to computers shipped with a 2230 solid
  • Dell Inspiron 15 7510 | Service Manual - Page 25
    in M.2 slot one and want to replace it with a M.2 2230 solid-state drive, you may need a mounting bracket (sold separately, please contact Dell support). NOTE: This procedure applies only if you are installing a 2230 solid-state drive in M.2 slot one. The following image indicates the location of
  • Dell Inspiron 15 7510 | Service Manual - Page 26
    the computer is in sleep or on state. 2. Enter Service Mode. 3. Remove the base cover. About this task NOTE: The M.2 card drive, you will need a mounting bracket (sold separately, please contact Dell support). NOTE: This procedure applies only to computers shipped with a 2280 solid
  • Dell Inspiron 15 7510 | Service Manual - Page 27
    solid-state drive in M.2 slot one. NOTE: When installing a M.2 2280 NVMe Gen4.0 x4 solid-state drive, you may order a copper thermal shield from Dell support for better thermal performance. The following image indicates the location of the 2280 solid-state drive that is installed in M.2 slot one and
  • Dell Inspiron 15 7510 | Service Manual - Page 28
    -state drive from M.2 slot two Prerequisites NOTE: M.2 slot two supports only 2230 solid-state drive. NOTE: This procedure applies only to solid-state drive while the computer is in sleep or on state. 2. Enter Service Mode. 3. Remove the base cover. About this task The following image indicates the
  • Dell Inspiron 15 7510 | Service Manual - Page 29
    the installation procedure. About this task NOTE: Solid-state drives are fragile. Exercise care when handling the solid-state drive. NOTE: M.2 slot two supports only 2230 solid-state drive. NOTE: This procedure applies only to computers shipped with a 2230 solid-state drive installed in M.2 slot two
  • Dell Inspiron 15 7510 | Service Manual - Page 30
    working inside your computer. Wireless card Removing the wireless card Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task The following images indicate the location of the wireless card and provide a visual
  • Dell Inspiron 15 7510 | Service Manual - Page 31
    the antenna cables to the wireless card. The following table provides the antenna-cable color scheme for the wireless card that is supported by your computer. Table 2. Antenna-cable color scheme Connectors on the wireless card Main Auxiliary Antenna-cable color Silkscreen marking White Black
  • Dell Inspiron 15 7510 | Service Manual - Page 32
    1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task The figure the palm-rest and keyboard assembly. 4. Unroute the I/O cable from routing guides underneath the GPU fan. 5. Slide and lift the GPU fan off the palm
  • Dell Inspiron 15 7510 | Service Manual - Page 33
    Mylar cover to access the cable connector. 2. Route the I/O cable through the routing guides underneath the GPU fan. 3. Slide and place the GPU fan on the palm- Install the base cover. 2. Exit Service Mode. 3. Follow the procedure in After working inside your computer. Removing and installing
  • Dell Inspiron 15 7510 | Service Manual - Page 34
    System fan Removing the system fan Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task The following images indicate the location of the fan and provide a visual representation of the removal procedure.
  • Dell Inspiron 15 7510 | Service Manual - Page 35
    to the palm-rest and keyboard assembly. 3. Connect the fan cable to the system board. Next steps 1. Install the base cover. 2. Exit Service Mode. 3. Follow the procedure in After working inside your computer. Heat sink Removing the heat sink Prerequisites 1. Follow the procedure in Before working
  • Dell Inspiron 15 7510 | Service Manual - Page 36
    About this task The following images indicate the location of the heat sink and provide a visual representation of the removal procedure. Steps 1. In reverse sequential order (as indicated on the Mylar cover), loosen the seven captive screws that secure the heat sink to the system board. 2. Lift
  • Dell Inspiron 15 7510 | Service Manual - Page 37
    cover), tighten the seven captive screws that secure the heat sink to the system board. Next steps 1. Install the base cover. 2. Exit Service Mode. 3. Follow the procedure in After working inside your computer. I/O board Removing the I/O board Prerequisites 1. Follow the procedure in Before working
  • Dell Inspiron 15 7510 | Service Manual - Page 38
    Steps 1. Open the latch, and disconnect the power button with fingerprint reader cable from the I/O board. 2. Open the latch, and disconnect the power button cable from the I/O board. 3. Peel the tape that secures the I/O-board cable to the I/O board. 4. Open the latch and disconnect the I/O-board
  • Dell Inspiron 15 7510 | Service Manual - Page 39
    that secures the I/O board to the palm-rest and keyboard assembly. Next steps 1. Install the GPU fan. 2. Install the base cover. 3. Exit Service Mode. 4. Follow the procedure in After working inside your computer. Speakers Removing the speakers Prerequisites 1. Follow the procedure in Before working
  • Dell Inspiron 15 7510 | Service Manual - Page 40
    secures the speaker cable to the palm-rest and keyboard assembly. 2. Note the speaker cable routing, and remove the speaker cable from the routing guides on the palm-rest and keyboard assembly. 3. Disconnect the speaker cable from the system board. 4. Lift the speakers, along with the cable, off the
  • Dell Inspiron 15 7510 | Service Manual - Page 41
    speaker cable to the system board. 3. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly. 4. Adhere the tape that secures the 2. Install the battery. 3. Install the base cover. 4. Exit Service Mode. 5. Follow the procedure in After working inside your computer.
  • Dell Inspiron 15 7510 | Service Manual - Page 42
    Steps 1. Open the latch and disconnect the touchpad cable from the system board. 2. Peel the tape that secures the touchpad bracket to the palm-rest and keyboard assembly. 3. Remove the three (M2x1.8) and the two (M2x3) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.
  • Dell Inspiron 15 7510 | Service Manual - Page 43
    Steps 1. Slide the touchpad into the slot on the palm-rest and keyboard assembly. NOTE: Turn the computer over and open the display. Ensure that the touchpad is equally aligned along all four sides. 2. Replace the two (M2x1.8) screws that secure the touchpad to the palm-rest and keyboard assembly.
  • Dell Inspiron 15 7510 | Service Manual - Page 44
    After working inside your computer. Display assembly Removing the display assembly Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. 4. Remove the heat sink. About this task The following images indicate the location of the
  • Dell Inspiron 15 7510 | Service Manual - Page 45
    Removing and installing components 45
  • Dell Inspiron 15 7510 | Service Manual - Page 46
    Steps 1. Disconnect the display cable from its connector on the system board. 2. Remove the two (M2.5x5) screws that secure the left-display hinge to the system board. 3. Remove the two (M2.5x5) screws that secure the right-display hinge to the system board. 4. Open the display hinges at an angle of
  • Dell Inspiron 15 7510 | Service Manual - Page 47
    Steps 1. Slide the display assembly at an angle, and place the display assembly on the palm-rest and keyboard assembly. 2. Using the alignment posts, close the display hinges. 3. Replace the two (M2.5x5) screws that secure the right-display hinge to the system board. 4. Replace the two (M2.5x5)
  • Dell Inspiron 15 7510 | Service Manual - Page 48
    inside your computer. Power-button board Removing the power-button board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. 4. Remove the GPU fan. 5. Remove the heat sink. About this task The following images indicate the
  • Dell Inspiron 15 7510 | Service Manual - Page 49
    the power-button cable to the I/O board. Next steps 1. Install the heat sink. 2. Install the GPU fan. 3. Install the base cover. 4. Exit Service Mode. 5. Follow the procedure in After working inside your computer. Power button with optional fingerprint reader Removing the power-button with optional
  • Dell Inspiron 15 7510 | Service Manual - Page 50
    3. Remove the battery. 4. Remove the heat sink. 5. Remove the GPU fan. 6. Remove the power-button board. About this task The following image indicates the location of the power-button with optional fingerprint reader and provides a visual representation of the removal procedure. Steps 1. Remove the
  • Dell Inspiron 15 7510 | Service Manual - Page 51
    assembly. Next steps 1. Install the power-button board. 2. Install the heat sink. 3. Install the GPU fan. 4. Install the base cover. 5. Exit Service Mode. 6. Follow the procedure in After working inside your computer. Power button with fingerprint reader Removing the power button with fingerprint
  • Dell Inspiron 15 7510 | Service Manual - Page 52
    About this task The following images indicate the location of the power button with fingerprint reader and provide a visual representation of the removal procedure. Steps 1. Disconnect the power button with fingerprint reader cable from the I/O board. 2. Remove the screw (M2x4) that secures the
  • Dell Inspiron 15 7510 | Service Manual - Page 53
    I/O board. Next steps 1. Install the power-button board. 2. Install the heat sink. 3. Install the GPU fan. 4. Install the base cover. 5. Exit Service Mode. 6. Follow the procedure in After working inside your computer. Power-adapter port Removing the power-adapter port Prerequisites 1. Follow the
  • Dell Inspiron 15 7510 | Service Manual - Page 54
    board. 4. Peel the tapes that secure the power-adapter port cable to the system board. 5. Remove the power-adapter port cable from the routing guide on the palm-rest and keyboard assembly. 6. Lift the power-adapter port, along with its cable, off the palm-rest and keyboard assembly. Installing
  • Dell Inspiron 15 7510 | Service Manual - Page 55
    and keyboard assembly. 2. Route the power-adapter port cable through the routing guide on the palm-rest and keyboard assembly. 3. Adhere the tapes that secure Install the heat sink. 2. Install the base cover. 3. Exit Service Mode. 4. Follow the procedure in After working inside your computer.
  • Dell Inspiron 15 7510 | Service Manual - Page 56
    2. Remove the base cover. 3. Remove the battery. 4. Remove the memory module. 5. Remove the M.2 2280 solid-state drive or M.2 2230 solid-state drive from M.2 slot one, whichever applicable. 6. Remove the M.2 2230 solid-state drive from M.2 slot two, if applicable. 7. Remove the wireless card. 8.
  • Dell Inspiron 15 7510 | Service Manual - Page 57
    Steps 1. Peel the tape that secures the display cable to the system board. 2. Open the latch and disconnect the display cable from the system board. 3. Peel the tape and disconnect the I/O-board cable from the system board. 4. Disconnect the speaker cable from the system board. 5. Open the latch,
  • Dell Inspiron 15 7510 | Service Manual - Page 58
    to simplify the procedure and preserve the thermal bond between the system board and heat-sink. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes any
  • Dell Inspiron 15 7510 | Service Manual - Page 59
    Steps 1. Align and place the system board on the palm-rest and keyboard assembly. 2. Replace the two (M2x2) screws and one (M2x4) screw that secure the system board to the palm-rest and keyboard assembly. 3. Connect the display cable to the system board and close the latch to secure the cable. 4.
  • Dell Inspiron 15 7510 | Service Manual - Page 60
    with the heat sink. 13. Remove the power-button board. 14. Remove the power button with optional fingerprint reader based on the system configuration. 15. Remove the power button with fingerprint reader based on the system configuration. 16. Remove the power-adapter port. 17. Remove the speakers. 18
  • Dell Inspiron 15 7510 | Service Manual - Page 61
    Installing the palm-rest and keyboard assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task Place the palm-rest and keyboard assembly on a flat surface. Removing and installing components 61
  • Dell Inspiron 15 7510 | Service Manual - Page 62
    fan. 13. Install the wireless card. 14. Install the M.2 2280 solid-state drive or M.2 2230 solid-state drive in M.2 slot one, whichever applicable. 15. Install the M.2 2230 solid-state drive in M.2 slot two, if applicable. 16. Install the memory module. 17. Install the battery. 18. Install the
  • Dell Inspiron 15 7510 | Service Manual - Page 63
    3 Drivers and downloads When troubleshooting, downloading or installing drivers it is recommended that you read the Dell Knowledge Based article, Drivers and Downloads FAQ SLN128938. Drivers and downloads 63
  • Dell Inspiron 15 7510 | Service Manual - Page 64
    boot device order and boot directly to a specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can: ● Access System Setup by pressing F2 key 64 System setup
  • Dell Inspiron 15 7510 | Service Manual - Page 65
    the ownership tag of the computer. Displays the manufacture date of the computer. Displays the ownership date of the computer. Displays the express service code of the computer. Displays the ownership tag of the computer. Displays whether the signed firmware update is enabled. Displays the battery
  • Dell Inspiron 15 7510 | Service Manual - Page 66
    Table 4. System setup options-System information menu (continued) Overview Health Displays the battery health. AC Adapter Displays whether an AC adapter is installed. Processor Information Processor Type Displays the processor type. Maximum Clock Speed Displays the maximum processor clock
  • Dell Inspiron 15 7510 | Service Manual - Page 67
    Configuration Enable External USB Ports Enables or disables USB ports to be functional in an operating system environment. Default: ON. Enable USB Boot Support Enables or disables booting from USB mass storage devices such as external hard drive, optical drive, and USB drive. Default: ON. Enable
  • Dell Inspiron 15 7510 | Service Manual - Page 68
    SSD-0/SATA-2 SATA-0 Drive Information Configures operating mode of the integrated SATA hard drive controller. Default: RAID. SATA is configured to support RAID (Intel Rapid Restore Technology). Enables or disables various onboard drives. Default: ON. Default: ON. Displays the information of various
  • Dell Inspiron 15 7510 | Service Manual - Page 69
    specified work period. Advanced Battery Charged maximizes battery health while still supporting heavy use during the work day. Default: OFF. Enable mode, Hibernate and Power Off. Default: OFF. Enable on Dell USB-C Dock Enables the Dell USB-C Dock when connected to wake the computer from Standby
  • Dell Inspiron 15 7510 | Service Manual - Page 70
    default, the option is disabled. Absolute Enable or disable or permanently disable the BIOS module interface of the optional Absolute Persistence Module service from Absolute software. By default, the Enable Absolute option is enabled. UEFI Boot Path Security Controls whether or not the computer
  • Dell Inspiron 15 7510 | Service Manual - Page 71
    enabled, this will disable the master password support. By default, the option is disabled. ) revert of NVMe hard-drives from the Dell Security Manager prompt. By default, the option option is enabled. BIOSConnect Enable or disable cloud Service OS recovery if the main operating system fails to
  • Dell Inspiron 15 7510 | Service Manual - Page 72
    Dell OS Recovery Tool. By default, the threshold value is set to 2. Table 14. System setup options-System Management menu System Management Service set ownership date. By default, the option is disabled. Table 15. System setup options-Keyboard menu Keyboard Numlock Enable Enable or disable
  • Dell Inspiron 15 7510 | Service Manual - Page 73
    by Intel Virtualization Technology for Direct I/O. By default, the option is enabled. Table 18. System setup options-Performance menu Performance Multi Core Support Active Cores Enables to change the number of CPU cores available to the operating system. By default, the All Cores options is
  • Dell Inspiron 15 7510 | Service Manual - Page 74
    Table 19. System setup options-System Logs menu System Logs BIOS Event Log Clear Bios Event Log Display BIOS events. By default, the Keep Log option is enabled. Thermal Event Log Clear Thermal Event Log Display Thermal events. By default, the Keep Log option is enabled. Power Event Log Clear
  • Dell Inspiron 15 7510 | Service Manual - Page 75
    . Clearing BIOS (System Setup) and System passwords About this task To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell. NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying Windows
  • Dell Inspiron 15 7510 | Service Manual - Page 76
    codes and recommended solutions are intended for Dell service technicians to troubleshoot problems. You should only perform troubleshooting and repairs as authorized or directed by the Dell technical support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty
  • Dell Inspiron 15 7510 | Service Manual - Page 77
    white) Problem description 1,1 troubleshoot and fix your computer when it fails to boot into their primary operating system due to software or hardware failures. For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at www.dell.com/support
  • Dell Inspiron 15 7510 | Service Manual - Page 78
    BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update. Backup media and recovery options It is recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes multiple options for recovering Windows operating
  • Dell Inspiron 15 7510 | Service Manual - Page 79
    Draining residual flea power, also known as a performing a "hard reset", is also a common troubleshooting step if your computer does not power on or boot into the operating system. To drain residual a hard reset, see the knowledge base article SLN85632 at www.dell.com/support. Troubleshooting 79
  • Dell Inspiron 15 7510 | Service Manual - Page 80
    through videos, manuals and documents. In Windows search, type Contact Support, and press Enter. www.dell.com/support/windows Your Dell computer is uniquely identified by a Service Tag or Express Service Code. To view relevant support resources for your Dell computer, enter the Service Tag or
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Inspiron 15 7510
Service Manual
Regulatory Model: P106F
Regulatory Type: P106F002
May 2021
Rev. A00