Dell Latitude 5530 Service Manual

Dell Latitude 5530 Manual

Get Dell Latitude 5530 PDF manuals and user guides View all Dell Latitude 5530 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell Latitude 5530 manual content summary:

  • Dell Latitude 5530 | Service Manual - Page 1
    Latitude 5530 Service Manual Regulatory Model: P104F Regulatory Type: P104F005/P104F006 March 2022 Rev. A00
  • Dell Latitude 5530 | Service Manual - Page 2
    of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2022 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be
  • Dell Latitude 5530 | Service Manual - Page 3
    instructions...7 Before working inside your computer...7 Safety precautions...8 Electrostatic discharge-ESD protection...8 ESD field service the memory modules...35 Battery...36 Lithium-ion battery precautions...36 Removing the 3-cell battery...37 Removing the 3-cell battery filler...38 Contents 3
  • Dell Latitude 5530 | Service Manual - Page 4
    filler...39 Installing the 3-cell battery...40 Removing the 4-cell battery...41 Installing the 4-cell battery...42 Battery cable...44 Removing the battery cable...44 Installing the battery cable...45 Assembly inner frame...46 Removing the assembly inner frame...46 Installing the assembly inner
  • Dell Latitude 5530 | Service Manual - Page 5
    palm-rest assembly...103 Installing the palm-rest assembly...104 Chapter 3: Drivers and downloads 106 Chapter 4: BIOS setup...107 BIOS overview...107 Entering System passwords 121 Chapter 5: Troubleshooting...122 Handling swollen Lithium-ion batteries...122 Dell SupportAssist Pre-boot System
  • Dell Latitude 5530 | Service Manual - Page 6
    Recovering the operating system...126 Real-Time Clock (RTC Reset)...126 Auto RTC reset...126 Backup media and recovery options...127 WiFi power cycle...127 Drain residual flea power (perform hard reset)...127 Chapter 6: Getting help and contacting Dell 128 6 Contents
  • Dell Latitude 5530 | Service Manual - Page 7
    troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions when handling Lithium-ion batteries in laptops. Swollen batteries should not be used
  • Dell Latitude 5530 | Service Manual - Page 8
    Service Mode or the computer does not support Service Mode then proceed to disconnect the battery cable. To disconnect the battery cable, follow the steps in Removing the battery electrocuted. Standby power Dell products with standby power obvious, such as intermittent problems or a shortened product
  • Dell Latitude 5530 | Service Manual - Page 9
    higher than in previous Dell products. For this The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use
  • Dell Latitude 5530 | Service Manual - Page 10
    for safe transport. ESD protection summary It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate
  • Dell Latitude 5530 | Service Manual - Page 11
    N/A M.2 2230 solid-state drive M2x4 1 M.2 2280 solid-state drive M2x4 1 Assembly inner frame M2x3 12 3-cell battery Captive screws 3 N/A 4-cell battery Captive screws 3 N/A Heat sink-integrated Captive screw 4 M2x3 1 Heat sink-discrete Captive screw 7 M2x3 1 Removing and
  • Dell Latitude 5530 | Service Manual - Page 12
    Screw type System fan M2x3 LED board M2x3 eDP cable/bracket M2x3 USB Type-C support bracket M2x4 Quantity 2 1 2 3 System board Power button Smart card reader to display back cover) M2.5x3.5 4 Screw image Major components of Latitude 5530 The following image shows the major components of
  • Dell Latitude 5530 | Service Manual - Page 13
    1. Base cover 3. System fan 5. System board 7. Speakers 2. Battery 4. Memory module 6. Keyboard assembly 8. Palm-rest assembly Removing and installing components 13
  • Dell Latitude 5530 | Service Manual - Page 14
    9. Display assembly 11. Coin-cell battery 13. Assembly inner frame 15. Solid-state drive 17. WLAN card 10. LED board 12. Power button/fingerprint board 14. Heat sink 16. WWAN card NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
  • Dell Latitude 5530 | Service Manual - Page 15
    Steps 1. Insert a pin into the hole of the SIM card tray and push inward until the tray is released 2. Slide the SIM card tray out of the slot on the computer. 3. Remove the SIM card from the SIM card tray. 4. Slide the SIM card tray into the slot, until it clicks into place. Installing the SIM card
  • Dell Latitude 5530 | Service Manual - Page 16
    Steps 1. Insert a pin into the hole of the SIM card tray and push inward until the tray is released 2. Slide the SIM card tray out of the slot on the computer. 3. Place the SIM card into the SIM card tray with the metallic contact facing up. 4. Align the SIM card tray with the slot on the computer
  • Dell Latitude 5530 | Service Manual - Page 17
    Steps 1. Push the microSD card to release it from the computer. 2. Slide the microSD card out of the computer. Installing the microSD card About this task The following image indicates the location of the microSD card and provides a visual representation of the installation procedure. Steps 1.
  • Dell Latitude 5530 | Service Manual - Page 18
    Next steps 1. Follow the procedure in after working inside your computer. Base cover Removing the base cover Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SIM card. 3. Remove the microSD card. About this task The following images indicate the location of
  • Dell Latitude 5530 | Service Manual - Page 19
    Steps 1. Loosen the eight captive screws that secure the base cover to the palm-rest assembly. 2. Using a plastic scribe, pry the base cover from the U-shaped indents at the top edge of the base cover to remove the base cover from the palm-rest assembly and keyboard assembly. 3. Grasp the left side
  • Dell Latitude 5530 | Service Manual - Page 20
    Steps 1. Align the screw holes on the base cover with the screw holes on the palm-rest assembly, and then snap the base cover into place. 2. Tighten the eight captive screws that secure the base cover to the palm-rest assembly. 20 Removing and installing components
  • Dell Latitude 5530 | Service Manual - Page 21
    Next steps 1. Install the microSD card. 2. Install the SIM card. 3. Follow the procedure in after working inside your computer. WLAN card Removing the WLAN card Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SIM card. 3. Remove the microSD card. 4. Remove
  • Dell Latitude 5530 | Service Manual - Page 22
    1. Loosen the captive screw that secures the WLAN card bracket to the WLAN card. 2. Remove the WLAN card bracket off the WLAN card. 3. Disconnect the antenna cables from the WLAN card. 4. Remove the WLAN card at an angle from the WLAN card slot. Installing the WLAN card Prerequisites If you are
  • Dell Latitude 5530 | Service Manual - Page 23
    Table 2. Antenna-cable color scheme Connectors on the WLAN card Auxiliary (black triangle) Antenna-cable color Black 2. Align the notch on the WLAN card with the tab on the WLAN-card slot. 3. Slide the WLAN card at an angle into the WLAN-card slot. 4. Place the WLAN-card bracket on the WLAN card.
  • Dell Latitude 5530 | Service Manual - Page 24
    Steps 1. Loosen the captive screw that secures the WWAN card bracket to the WWAN card. 2. Slide and remove the WWAN-card bracket off the WWAN card. 3. Disconnect the antenna cables from the WWAN card. 4. Slide at an angle and remove the WWAN card from the WWAN-card slot. Installing the WWAN card
  • Dell Latitude 5530 | Service Manual - Page 25
    to secure the WWAN-card bracket to the WWAN card. NOTE: For instructions on how to find your computer's IMEI (International Mobile Station Equipment Identity) number, see the knowledge base article 000143678 at www.dell.com/support. Next steps 1. Install the base cover. 2. Install the microSD card
  • Dell Latitude 5530 | Service Manual - Page 26
    Solid-state drive Applying the solid-state drive thermal pad About this task The following image indicates the re-usable solid-state drive thermal pad. Steps NOTE: While replacing the system board, if a thermal pad is present in the solid-state drive slot, peel and transfer the re-useable thermal
  • Dell Latitude 5530 | Service Manual - Page 27
    the below procedure to remove the M.2 2280 solid-state drive from SLOT 1 and SLOT 2. NOTE: SLOT1 supports only PCIe Gen4 Solid-state drive and does not support any Intel Optane. NOTE: SLOT2 supports only PCIe Gen3 Solid-state drive and Intel Optane. The following images indicate the location of the
  • Dell Latitude 5530 | Service Manual - Page 28
    below procedure to install the M.2 2280 solid-state drive in both SLOT 1 and SLOT 2. NOTE: SLOT1 supports only PCIe Gen4 Solid-state drive and does not support any Intel Optane. NOTE: SLOT2 supports only PCIe Gen3 Solid-state drive and Intel Optane. The following image indicates the location of the
  • Dell Latitude 5530 | Service Manual - Page 29
    Figure 3. M.2 2280 solid-state drive without bracket Figure 4. M.2 2280 solid-state drive with bracket Steps 1. Installing M.2 2280 solid-state drive without bracket: a. Align the notch on the solid-state drive with the tab on the solid-state drive slot. b. Slide the M.2 2280 solid-state drive at
  • Dell Latitude 5530 | Service Manual - Page 30
    the below procedure to remove the M.2 2230 solid-state drive from SLOT 1 and SLOT 2. NOTE: SLOT1 supports only PCIe Gen4 Solid-state drive and does not support any Intel Optane. NOTE: SLOT2 supports only PCIe Gen3 Solid-state drive and Intel Optane. The following images indicate the location of the
  • Dell Latitude 5530 | Service Manual - Page 31
    Figure 6. M.2 2230 solid-state drive with bracket Steps 1. Removing M.2 2230 solid-state drive without bracket: a. Remove the (M2x4) screw that secures the M.2 2230 solid-state drive to its slot on the system board. b. Slide at an angle and remove the M.2 2230 solid-state drive from the solid-state
  • Dell Latitude 5530 | Service Manual - Page 32
    Steps Pry and remove the M.2 2230 solid-state drive holder from the screw hole on the system board. Installing the M.2 2230 solid-state drive holder Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The
  • Dell Latitude 5530 | Service Manual - Page 33
    below procedure to install the M.2 2230 solid-state drive in both SLOT 1 and SLOT 2. NOTE: SLOT1 supports only PCIe Gen4 Solid-state drive and does not support any Intel Optane. NOTE: SLOT2 supports only PCIe Gen3 Solid-state drive and Intel Optane. The following image indicates the location of the
  • Dell Latitude 5530 | Service Manual - Page 34
    Figure 8. M.2 2230 solid-state drive with bracket Steps 1. Installing M.2 2230 solid-state drive without bracket: a. Align the notch on the solid-state drive with the tab on the solid-state drive slot. b. Slide the M.2 2230 solid-state drive at an angle into its slot on the system board. c. Replace
  • Dell Latitude 5530 | Service Manual - Page 35
    Steps 1. Pry the securing clips from both side of the memory module until the memory module pops up. 2. Remove the memory module from the memory-module slot. NOTE: Repeat step 1 and 2 if there are two memory modules. Installing the memory modules Prerequisites If you are replacing a component,
  • Dell Latitude 5530 | Service Manual - Page 36
    3. Install the SIM card. 4. Follow the procedure in after working inside your computer. Battery Lithium-ion battery precautions CAUTION: ● Exercise caution when handling Lithium-ion batteries. ● Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and
  • Dell Latitude 5530 | Service Manual - Page 37
    can be dangerous. In such an instance, contact Dell technical support for assistance. See www.dell.com/contactdell. ● Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers. ● Swollen batteries should not be used and should be replaced and disposed properly
  • Dell Latitude 5530 | Service Manual - Page 38
    if it was not disconnected earlier. 2. Loosen the three captive screws that secure the battery to the palm-rest assembly. 3. Lift the battery off the palm-rest assembly. Removing the 3-cell battery filler Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SIM
  • Dell Latitude 5530 | Service Manual - Page 39
    filler outwards to release it from the tabs in the battery. 2. Remove the battery filler from the 3-cell battery. Installing the 3-cell battery filler Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The
  • Dell Latitude 5530 | Service Manual - Page 40
    3. Install the microSD card. 4. Install the SIM card. 5. Follow the procedure in after working inside your computer. Installing the 3-cell battery Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following
  • Dell Latitude 5530 | Service Manual - Page 41
    disconnected from system board for service, then there is a delay during system boot-up as the system undergoes RTC battery reset. Steps 1. Align the screw holes on the battery with the screw holes on the palm-rest assembly. 2. Tighten the three captive screws to secure the battery to the palm-rest
  • Dell Latitude 5530 | Service Manual - Page 42
    4. Remove the base cover. NOTE: If battery is disconnected from system board for service, then there is a delay during system boot-up as the system undergoes RTC battery reset. About this task The following images indicate the location of the battery and provide a visual representation of the
  • Dell Latitude 5530 | Service Manual - Page 43
    is disconnected from system board for service, then there is a delay during system boot-up as the system undergoes RTC battery reset. Steps 1. Align and place the battery into its slot on the palm-rest assembly. 2. Tighten the three captive screws to secure the battery to the palm-rest assembly
  • Dell Latitude 5530 | Service Manual - Page 44
    before working inside your computer. 2. Remove the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the 3-cell battery or 4-cell battery. NOTE: If battery is disconnected from system board for service, then there is a delay during system boot-up as the system undergoes RTC
  • Dell Latitude 5530 | Service Manual - Page 45
    of the installation procedure. Steps 1. Align and route the battery cable through the routing guides on the battery. 2. Connect the battery cable to the connector on the battery. Next steps 1. Install the 3-cell battery or 4-cell battery. 2. Install the base cover. 3. Install the microSD card
  • Dell Latitude 5530 | Service Manual - Page 46
    SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the WLAN card. 6. Remove the WWAN card. 7. Remove the 3-cell battery or 4-cell battery. About this task The following image indicates the location of the assembly inner frame and provides a visual representation of the removal
  • Dell Latitude 5530 | Service Manual - Page 47
    shipped with power button only: a. Disconnect the speaker cable from the connector on the system board, and unroute the speaker cable from the routing guides on the assembly inner frame. b. Remove the twelve (M2x3) screws that secure the assembly inner frame to the system board and the palm-rest
  • Dell Latitude 5530 | Service Manual - Page 48
    48 Removing and installing components
  • Dell Latitude 5530 | Service Manual - Page 49
    assembly inner frame. 5. Route the speaker cable through the routing guides on the assembly inner frame, and connect the speaker cable to the connector on the system board. Next steps 1. Install the 3-cell battery or 4-cell battery. 2. Install the WWAN card. 3. Install the WLAN card. 4. Install the
  • Dell Latitude 5530 | Service Manual - Page 50
    Steps 1. Open the latch and disconnect the smart-card reader cable from the connector on the USH-daughter board. 2. Remove the smart-card reader cable away from the USH-daughter board. 3. Disconnect the LED-board cable from the connector on the system board and unroute the cable. 4. Remove the (M2x3
  • Dell Latitude 5530 | Service Manual - Page 51
    the connector on the USH-daughter board and close the latch. Next steps 1. Install the assembly inner frame. 2. Install the 3-cell battery or 4-cell battery. 3. Install the WWAN card. 4. Install the WLAN card. 5. Install the base cover. 6. Install the microSD card. 7. Install the SIM card. 8. Follow
  • Dell Latitude 5530 | Service Manual - Page 52
    before working inside your computer. 2. Remove the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the 3-cell battery or 4-cell battery. About this task The following images indicate the location of the system fan and provide a visual representation of the removal procedure
  • Dell Latitude 5530 | Service Manual - Page 53
    to the palm-rest assembly. 3. Connect the system-fan cable to the connector on the system board. Next steps 1. Install the 3-cell battery or 4-cell battery. 2. Install the base cover. 3. Install the microSD card. 4. Install the SIM card. 5. Follow the procedure in after working inside your computer
  • Dell Latitude 5530 | Service Manual - Page 54
    to cool before you touch it. 2. Remove the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the 3-cell battery or 4-cell battery. About this task The following image indicates the location of the heat sink and provides a visual representation of the removal procedure. 54
  • Dell Latitude 5530 | Service Manual - Page 55
    Steps 1. Remove the (M2x3) screw that secures the heat sink to the palm-rest assembly. 2. Loosen the four captive screws that secure the heat sink to the system board. 3. Lift the heat sink off the system board. Installing the heat sink (for computers shipped with integrated graphics card)
  • Dell Latitude 5530 | Service Manual - Page 56
    to cool before you touch it. 2. Remove the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the 3-cell battery or 4-cell battery. About this task The following image indicates the location of the heat sink and provides a visual representation of the removal procedure. 56
  • Dell Latitude 5530 | Service Manual - Page 57
    Steps 1. Remove the (M2x3) screw that secures the heat sink to the palm-rest assembly 2. Loosen the seven captive screws that secure the heat sink to the system board. 3. Lift the heat sink off the system board. Installing the heat sink (for computers shipped with discrete graphics card)
  • Dell Latitude 5530 | Service Manual - Page 58
    the system board. 3. Replace the (M2x3) screw to secure the heat sink to the palm-rest assembly. Next steps 1. Install the 3-cell battery or 4-cell battery. 2. Install the base cover. 3. Install the microSD card. 4. Install the SIM card. 5. Follow the procedure in after working inside your computer
  • Dell Latitude 5530 | Service Manual - Page 59
    or 4-cell battery. 6. Remove the assembly inner frame. About this task The following images indicate the location of the speaker and provide a visual representation of the removal procedure. Steps 1. Unroute the speaker cable from the routing guides on the palm-rest assembly. 2. Lift the speakers
  • Dell Latitude 5530 | Service Manual - Page 60
    the speakers on the palm-rest assembly. 2. Route the speaker cable through the routing guide on the palm-rest assembly. Next steps 1. Install the assembly inner frame. 2. Install the 3-cell battery or 4-cell battery. 3. Install the base cover. 4. Install the microSD card. 5. Install the SIM card
  • Dell Latitude 5530 | Service Manual - Page 61
    Remove the WLAN card. 8. Remove the WWAN card. 9. Remove the heat sink (integrated) or heat sink (discrete). 10. Remove the 3-cell battery or 4-cell battery. 11. Remove the system fan. 12. Remove the assembly inner frame. About this task The following images indicate the location of the system board
  • Dell Latitude 5530 | Service Manual - Page 62
    62 Removing and installing components
  • Dell Latitude 5530 | Service Manual - Page 63
    must remove the two M2x3 screws securing the system fan to the palm-rest assembly. Steps 1. Pry the coin-cell battery off the palm-rest assembly and unroute it from the routing guides on the palm-rest assembly. 2. Open the latch and disconnect the USH board cable from the system board. 3. Open
  • Dell Latitude 5530 | Service Manual - Page 64
    a visual representation of the installation procedure. 1. Fingerprint reader connector 3. Camera/IR cable connector 5. Solid-state drive-SSD-1 slot 7. Battery cable connector 9. LED board connector 11. Solid-state drive-SSD-2 slot 13. Speaker cable connector 2. WLAN connector 4. eDP/display cable
  • Dell Latitude 5530 | Service Manual - Page 65
    Removing and installing components 65
  • Dell Latitude 5530 | Service Manual - Page 66
    the three (M2x3) screws to secure the system board to the palm-rest assembly. 6. Route the coin-cell battery cable through the routing guide on palm-rest assembly and adhere the coin-cell battery on the palm-rest assembly. 7. Connect the USH board cable to the system board and close the latch to
  • Dell Latitude 5530 | Service Manual - Page 67
    state drive or M.2 2230 solid-state drive. 6. Remove the memory module. 7. Remove the WLAN card. 8. Remove the WWAN card. 9. Remove the 3-cell battery or 4-cell battery. 10. Remove the system fan. 11. Remove the assembly inner frame. 12. Remove the system board. NOTE: The system board can be removed
  • Dell Latitude 5530 | Service Manual - Page 68
    Steps 1. Remove the two (M2x2) screws that secure the power-button board to the palm-rest assembly. 2. Lift the power-button board off the palm-rest assembly. Installing the power-button board About this task The following images indicate the location of the power-button board and provide a visual
  • Dell Latitude 5530 | Service Manual - Page 69
    bond between the system board and heat sink. 2. Install the assembly inner frame. 3. Install the system fan. 4. Install the 3-cell battery or 4-cell battery. 5. Install the WWAN card. 6. Install the WLAN card. 7. Install the memory module. 8. Install the M.2 2280 solid-state drive or M.2 2230
  • Dell Latitude 5530 | Service Manual - Page 70
    SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the WLAN card. 6. Remove the WWAN card. 7. Remove the 3-cell battery or 4-cell battery. 8. Remove the assembly inner frame. NOTE: For models with smart card reader configuration, the smart card reader is pre-installed in the
  • Dell Latitude 5530 | Service Manual - Page 71
    Steps 1. Open the latch and disconnect the smart card reader cable from the connector on the USH board. 2. Remove the two (M2x3) screws that secure the smart card reader to the palm-rest assembly. 3. Lift the smart card reader off the palm-rest assembly. Installing the smart card reader
  • Dell Latitude 5530 | Service Manual - Page 72
    smart card reader cable to the connector on the USH board. Next steps 1. Install the assembly inner frame. 2. Install the 3-cell battery or 4-cell battery. 3. Install the WWAN card. 4. Install the WLAN card. 5. Install the base cover. 6. Install the microSD card. 7. Install the SIM card. 8. Follow
  • Dell Latitude 5530 | Service Manual - Page 73
    the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the WLAN card. 6. Remove the WWAN card. 7. Remove the 3-cell battery or 4-cell battery. 8. Remove the system fan. 9. Remove the assembly inner frame. 10. Remove the system board. NOTE: The system board can be removed with
  • Dell Latitude 5530 | Service Manual - Page 74
    Steps 1. Open the latch and disconnect the backlight cable and the keyboard cable from the connector on the touchpad. 2. Open the plastic tapes on the keyboard assembly to access the keyboard assembly screws. 3. Remove the twenty-six (M2x2) screws that secure the keyboard assembly to the palm-rest
  • Dell Latitude 5530 | Service Manual - Page 75
    thermal bond between the system board and heat sink. 2. Install the assembly inner frame. 3. Install the system fan. 4. Install the 3-cell battery or 4-cell battery. 5. Install the WWAN card. 6. Install the WLAN card. 7. Install the base cover. 8. Install the microSD card. 9. Install the SIM card
  • Dell Latitude 5530 | Service Manual - Page 76
    the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the WLAN card. 6. Remove the WWAN card. 7. Remove the 3-cell battery or 4-cell battery. 8. Remove the system fan. 9. Remove the assembly inner frame. 10. Remove the system board. NOTE: The system board can be removed with
  • Dell Latitude 5530 | Service Manual - Page 77
    thermal bond between the system board and heat sink. 3. Install the assembly inner frame. 4. Install the system fan. 5. Install the 3-cell battery or 4-cell battery. 6. Install the WWAN card. 7. Install the WLAN card. 8. Install the base cover. 9. Install the microSD card. 10. Install the SIM card
  • Dell Latitude 5530 | Service Manual - Page 78
    Display assembly Removing the display assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the WLAN card. 6. Remove the WWAN card. About this task The following images indicate
  • Dell Latitude 5530 | Service Manual - Page 79
    Removing and installing components 79
  • Dell Latitude 5530 | Service Manual - Page 80
    cable from the connector on the system board. 7. Disconnect the eDP cable from the connector on the system board and unroute it from the routing guide. 8. Remove the six (M2.5x5) screws that secure the display hinges to the system board. 9. Open the display assembly to a 180 degree and flip over
  • Dell Latitude 5530 | Service Manual - Page 81
    Removing and installing components 81
  • Dell Latitude 5530 | Service Manual - Page 82
    system board. 5. Route the display and eDP cable through the routing guide on the system board. 6. Connect the eDP cable to the connector cable bracket to the system board. 11. Route the antenna cables through the routing guide. Next steps 1. Install the WWAN card. 2. Install the WLAN card. 3.
  • Dell Latitude 5530 | Service Manual - Page 83
    About this task The following images indicate the location of the display bezel and provide a visual representation of the removal procedure. Steps NOTE: The display bezel is adhered to the display panel with adhesive. Insert a plastic scribe into the recesses near both hinge caps to start the
  • Dell Latitude 5530 | Service Manual - Page 84
    Steps NOTE: While installing the replacement display bezel for the models that are shipped with a camera, carefully peel off the piece of tape that is used to secure the camera shutter to the replacement display bezel. CAUTION: You must take extra care when peeling the tape. An abrupt peeling may
  • Dell Latitude 5530 | Service Manual - Page 85
    About this task The following images indicate the location of the display panel and provide a visual representation of the removal procedure. Removing and installing components 85
  • Dell Latitude 5530 | Service Manual - Page 86
    86 Removing and installing components
  • Dell Latitude 5530 | Service Manual - Page 87
    Steps NOTE: The display panel is preassembled with the display brackets as a single service part. Do not pull the Stretch Release (SR) tapes and separate the brackets from the display panel. 1. Remove the four (M2.5x3.5) screws that secure
  • Dell Latitude 5530 | Service Manual - Page 88
    88 Removing and installing components
  • Dell Latitude 5530 | Service Manual - Page 89
    Steps 1. Connect the display cable to the connector on the display panel and close the latch. 2. Adhere the conductive tape to secure the display cable to the display panel. 3. Insert the display panel tabs into the slots on the display cover. 4. Replace the four (M2.5x3.5) screws to secure the
  • Dell Latitude 5530 | Service Manual - Page 90
    Display hinges Removing the display hinges Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the display assembly. 6. Remove the display bezel. 7. Remove the display panel. About this
  • Dell Latitude 5530 | Service Manual - Page 91
    2. Lift and remove the right hinge from the display back cover. 3. Remove the (M2.5x3.5) screw that secures the left hinge to the display back cover. 4. Lift and remove the left hinge from the display back cover. Installing the display hinges Prerequisites If you are replacing a component, remove
  • Dell Latitude 5530 | Service Manual - Page 92
    Next steps 1. Install the display panel. 2. Install the display bezel. 3. Install the display assembly. 4. Install the base cover. 5. Install the microSD card. 6. Install the SIM card. 7. Follow the procedure in after working inside your computer. Camera/microphone module Removing the camera/
  • Dell Latitude 5530 | Service Manual - Page 93
    Installing the camera/microphone module Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the camera/microphone module and provides a visual representation of the
  • Dell Latitude 5530 | Service Manual - Page 94
    About this task The following images indicate the location of the infrared camera module and provide a visual representation of the removal procedure. Steps 1. Peel the two conductive tapes that secure the camera/microphone module in place. 2. Disconnect the camera/microphone cable from the
  • Dell Latitude 5530 | Service Manual - Page 95
    Steps 1. Align and place the infrared camera module into the slot on the display back cover. 2. Connect the infrared camera cable to the connector on the infrared camera module. Next steps 1. Install the display hinges. 2. Install the display panel. 3. Install the display bezel. 4. Install the
  • Dell Latitude 5530 | Service Manual - Page 96
    Steps 1. Disconnect the eDP cable from the connector on the camera module. 2. Peel the conductive tape and unroute the eDP cable to release it from adhesive and lift the eDP cable from the display back cover. Installing the eDP cable Prerequisites If you are replacing a component, remove the
  • Dell Latitude 5530 | Service Manual - Page 97
    Steps 1. Connect the eDP cable to the connector on the camera module. 2. Adhere the eDP cable to the display back cover. 3. Adhere the conductive tape and route the eDP cable to the display back cover. Next steps 1. Install the display panel. 2. Install the display bezel. 3. Install the display
  • Dell Latitude 5530 | Service Manual - Page 98
    3. Remove the microSD card. 4. Remove the base cover. 5. Remove the display assembly. 6. Remove the display bezel. 7. Remove the display panel. About this task The following images indicate the location of the sensor board and provide a visual representation of the removal procedure. Steps 1. Open
  • Dell Latitude 5530 | Service Manual - Page 99
    Steps 1. Align and place the sensor board on the display back cover. 2. Connect the display cable to the connector on the sensor board and close the latch. Next steps 1. Install the display panel. 2. Install the display bezel. 3. Install the display assembly. 4. Install the base cover. 5. Install
  • Dell Latitude 5530 | Service Manual - Page 100
    Steps After performing the steps in the pre-requisites, we are left with the display back cover. Installing the display back cover Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate
  • Dell Latitude 5530 | Service Manual - Page 101
    the SIM card. 3. Remove the microSD card. 4. Remove the base cover. 5. Remove the WLAN card. 6. Remove the WWAN card. 7. Remove the 3-cell battery or 4-cell battery. 8. Remove the system fan. 9. Remove the assembly inner frame. 10. Remove the system board. Removing and installing components 101
  • Dell Latitude 5530 | Service Manual - Page 102
    13. Remove the display assembly. About this task NOTE: For models shipped with WLAN antennas only, the dummy SIM-card slot filler is a separate service part and is not included with replacement palm rest. As a result, the dummy SIM-card slot filler must be removed and then reinstalled when replacing
  • Dell Latitude 5530 | Service Manual - Page 103
    the thermal bond between the system board and heat sink. 5. Install the assembly inner frame. 6. Install the system fan. 7. Install the 3-cell battery or 4-cell battery. 8. Install the WWAN card. 9. Install the WLAN card. 10. Install the base cover. 11. Install the microSD card. 12. Install the SIM
  • Dell Latitude 5530 | Service Manual - Page 104
    3. Remove the microSD card. 4. Remove the base cover. 5. Remove the WLAN card. 6. Remove the WWAN card. 7. Remove the 3-cell battery or 4-cell battery. 8. Remove the system fan. 9. Remove the assembly inner frame. 10. Remove the system board. NOTE: The system board can be removed with the heat sink
  • Dell Latitude 5530 | Service Manual - Page 105
    sink attached in order to simplify the procedure and preserve the thermal bond between the system board and heat sink. 8. Install the 3-cell battery or 4-cell battery. 9. Install the WWAN card. 10. Install the WLAN card. 11. Install the base cover. 12. Install the microSD card. 13. Install the SIM
  • Dell Latitude 5530 | Service Manual - Page 106
    3 Drivers and downloads When troubleshooting, downloading or installing drivers it is recommended that you read the Dell Knowledge Based article, Drivers and Downloads FAQ 000123347. 106 Drivers and downloads
  • Dell Latitude 5530 | Service Manual - Page 107
    4 BIOS setup CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program. Certain changes can make your computer work incorrectly. NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed. NOTE
  • Dell Latitude 5530 | Service Manual - Page 108
    this section may or may not appear. Table 5. System setup options-System information menu Overview Latitude 5520 BIOS Version Displays the BIOS version number. Service Tag Displays the Service Tag of the computer. Asset Tag Displays the Asset Tag of the computer. Manufacture Date Displays
  • Dell Latitude 5530 | Service Manual - Page 109
    Table 5. System setup options-System information menu (continued) Overview Processor L3 Cache Displays the processor L3 Cache size. Microcode Version Displays the microcode version. Intel Hyper-Threading Capable Displays whether the processor is Hyper-Threading (HT) capable. 64-Bit
  • Dell Latitude 5530 | Service Manual - Page 110
    during BIOS Pre-boot. By default, the Enable Thunderbolt Boot Support option is disabled. Enable Thunderbolt (and PCIe behind TBT) -C Ports option is disabled. Type-C Dock Override Enables to use connected Type-C Dell Dock to provide data stream with external USB ports disabled. When Type-C Dock
  • Dell Latitude 5530 | Service Manual - Page 111
    Mode option is not enabled. Table 9. System setup options-Display menu Display Display Brightness Brightness on battery power Enable to set screen brightness when the computer is running on battery power. Brightness on AC power Enable to set screen brightness when the computer is running on
  • Dell Latitude 5530 | Service Manual - Page 112
    With Auto Mode, the HTTPs Boot extracts Boot URL from the DHCP. With Manual Mode, the HTTPs Boot reads Boot URL from the user-provided data. By Table 11. System setup options-Power menu Power Battery configuration Enables the computer to run on battery during peak power usage hours. Use the
  • Dell Latitude 5530 | Service Manual - Page 113
    . By default, the Lid Switch option is enabled. Intel Speed Shift Technology Enable or disable the Intel speed shift technology support. By default, the Intel Speed Shift Technology option is enabled. Long Life Cycle Primary Battery By default, the Normal Battery option is enabled. Table 12
  • Dell Latitude 5530 | Service Manual - Page 114
    default, the option is enabled. Absolute Enable or disable or permanently disable the BIOS module interface of the optional Absolute Persistence Module service from Absolute software. By default, the option is enabled. UEFI Boot Path Security Controls whether or not the computer will prompt the
  • Dell Latitude 5530 | Service Manual - Page 115
    Master Password Lockout When enabled, this will disable the master password support. By default, the option is disabled. Allow Non-Admin PSID Revert Threshold setup option and local Service OS does not boot or is not installed. By default, the option is enabled. Dell Auto OS Recovery Threshold
  • Dell Latitude 5530 | Service Manual - Page 116
    to the computer. By default, the 10 seconds option is enabled. Keyboard Backlight Timeout on Battery Set the timeout value for the keyboard backlight when the is running only on battery power. By default, the 10 seconds option is enabled. Device Configuration Hotkey Access Manages whether
  • Dell Latitude 5530 | Service Manual - Page 117
    by Intel Virtualization Technology for Direct I/O. By default, the option is enabled. Table 19. System setup options-Performance menu Performance Multi Core Support Active Cores Enables to change the number of CPU cores available to the operating system. By default, the All Cores options is
  • Dell Latitude 5530 | Service Manual - Page 118
    Search support box, enter the Service Tag of your computer, and then click Search. NOTE: If you do not have the Service Tag, use the SupportAssist feature to automatically identify your computer. You can also use the product ID or manually browse for your computer model. 3. Click Drivers & Downloads
  • Dell Latitude 5530 | Service Manual - Page 119
    press Enter. The BIOS Update Utility appears. 8. Follow the on-screen instructions to complete the BIOS update. Updating the BIOS from the F12 One-Time Dell Support website and copied to the root of the USB drive ● AC power adapter that is connected to the computer ● Functional computer battery to
  • Dell Latitude 5530 | Service Manual - Page 120
    System and setup password Table 21. System and setup password Password type System password Setup password Description Password that you must enter to log in to your system. Password that you must enter to access and make changes to the BIOS settings of your computer. You can create a system
  • Dell Latitude 5530 | Service Manual - Page 121
    . Clearing BIOS (System Setup) and System passwords About this task To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell. NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying Windows
  • Dell Latitude 5530 | Service Manual - Page 122
    that are not covered under warranty should be disposed of at an approved recycling center. Contact Dell product support at https://www.dell.com/support for assistance and further instructions. ● Using a non-Dell or incompatible battery may increase the risk of fire or explosion. Replace the
  • Dell Latitude 5530 | Service Manual - Page 123
    more information, see https://www.dell.com/support/kbdoc/000180971. Running the SupportAssist EC) failures. NOTE: M-BIST can be manually initiated before POST (Power On Self Test). a problem with the system board 3. If there is a failure with the system board, the battery status Troubleshooting 123
  • Dell Latitude 5530 | Service Manual - Page 124
    supplied to the LCD (i.e., the L-BIST circuit fails), the battery status LED will flash either an error code [2,8] or an is an inherent problem with the LCD (screen) of the Dell laptop or with the Latitude 5530. Table 23. System-diagnostic lights Blinking pattern Amber White 1 1 Problem
  • Dell Latitude 5530 | Service Manual - Page 125
    EC code flow errors Disconnect all power source (AC, battery, coin cell) and drain flea power by pressing and holding down power button for 3~5 seconds. CPU failure ● Run the Dell Support Assist/Dell Diagnostics tool. ● If problem persists, replace the system board. System board failure
  • Dell Latitude 5530 | Service Manual - Page 126
    all power source (AC, battery, coin cell) and drain flea power by pressing and holding down power button 3~5 seconds to ensure all power are drained. ● Run "BIOS recovery from USB", and the instructions are in the website Dell support. ● If problem persists, replace the system board
  • Dell Latitude 5530 | Service Manual - Page 127
    recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup Media and Recovery Options. WiFi power cycle About this task If
  • Dell Latitude 5530 | Service Manual - Page 128
    , and press Enter. www.dell.com/support/windows www.dell.com/support/linux Access top solutions, diagnostics, drivers and downloads, and learn more about your computer through videos, manuals and documents. Your Dell computer is uniquely identified by a Service Tag or Express Service Code. To view
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Latitude 5530
Service Manual
Regulatory Model: P104F
Regulatory Type: P104F005/P104F006
March 2022
Rev. A00