Dell Networking 7048 Release Notes

Dell Networking 7048 Manual

Get Dell Networking 7048 PDF manuals and user guides View all Dell Networking 7048 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell Networking 7048 manual content summary:

  • Dell Networking 7048 | Release Notes - Page 1
    8164/8132F/8164F/7024/7048/7024P/7048P/7024F/7048R/ 7048R-RA/8024/8024F/M6220/M6348/M8024/M8024-k PowerConnect 5.1.0.1 Firmware Release Notes Date: April 2013 System Firmware Version 5.1.0.1 Information in this document is subject to change without notice. © 2003 - 2013 Dell Inc. All rights reserved
  • Dell Networking 7048 | Release Notes - Page 2
    Support Firmware Specifications Firmware Upgrade Firmware Downgrade Boot Code Downgrade Hardware Supported Support Matrix Supported Firmware Functionality Added Functionality in this Release Changed Functionality in this Release Issues Resolved CLI Reference Guide Updates User's Configuration Guide
  • Dell Networking 7048 | Release Notes - Page 3
    for the Dell PowerConnect 8132/8164/8132F/8164F/7024/7048/7024P/7048P/7024F/7048R/7048R-RA/8024/8024F/M6220/M6348/M8024/M8024-k switches firmware version 5.1.0.1. It is recommended that this release note be thoroughly reviewed prior to installing or upgrading of this product. Global Support For
  • Dell Networking 7048 | Release Notes - Page 4
    to follow the procedures described in that document when upgrading firmware may result in an inoperable switch! NOTE: OMNM (Open Manage Network Manager) v5.2 SP1 supports firmware management of PowerConnect 7024/7048/7024P/7048P/7024F/7048R/7048RRA/8024/8024F/M6220/M6348/M8024/M8024-k to deploy the
  • Dell Networking 7048 | Release Notes - Page 5
    M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Firmware Downgrade Downgrading from 5.1.0.1 to an earlier release is supported on most PowerConnect series switches (except PC81xx series with B1 CPU versions, see note below); however, migration of configuration information from
  • Dell Networking 7048 | Release Notes - Page 6
    Dell PowerConnect 7024 Ethernet Switch • Dell PowerConnect 7048 Ethernet Switch • Dell PowerConnect 7024P Ethernet Switch • Dell PowerConnect 7048P Ethernet Switch • Dell PowerConnect 7024F Ethernet Switch • Dell PowerConnect 7048R Ethernet Switch • Dell PowerConnect 7048R-RA Ethernet Switch • Dell
  • Dell Networking 7048 | Release Notes - Page 7
    supported on all switches. Feature/Switch Dell PowerConnect M6220 Ethernet Switch Dell PowerConnect M6348 Ethernet Switch Dell PowerConnect 7024 Ethernet Switch Dell PowerConnect 7048 Ethernet Switch Dell PowerConnect 7024P Ethernet Switch Dell PowerConnect 7048P Ethernet Switch Dell PowerConnect
  • Dell Networking 7048 | Release Notes - Page 8
    Supported Firmware Functionality For more details regarding all the supported firmware features and functionality, please refer to the Dell PowerConnect Series CLI Reference Guide and the Dell PowerConnect Series User's Configuration Guide. 6 System Firmware Version 5.1.0.1
  • Dell Networking 7048 | Release Notes - Page 9
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Added Functionality in this Release This section contains a list of features added in this release that are new for at least one switch listed in the Hardware Supported
  • Dell Networking 7048 | Release Notes - Page 10
    use. Users may observe a single port flap when the media type is changed from RJ45 to auto-select RJ45 and only the corresponding SFP port is enabled. Refer to the CLI Reference Guide Updates section below for the complete syntax. Release 4.1.0.6  IPv4-Only Mode Optimization PowerConnect switches
  • Dell Networking 7048 | Release Notes - Page 11
    -k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes  Auto-Install USB based auto-install is an easy way to quickly bring up a switch with a known configuration. Network based autoinstall is useful in rolling out a configuration or firmware update to a group of switches or in
  • Dell Networking 7048 | Release Notes - Page 12
    only if per-queue configuration is not supported) • WRED decay exponent Switch administrators should remember to configure ingress ports as trusted or un-trusted. By default ingress ports trust dot1p values.  Stack Firmware Synchronization Stack firmware synchronization updates all stack members to
  • Dell Networking 7048 | Release Notes - Page 13
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Dell EqualLogic arrays are required to be upgraded to firmware 5.0.2 or later in order to use the iSCSI Optimization feature.  LLDP Administrators should ensure that
  • Dell Networking 7048 | Release Notes - Page 14
    the flash • File changes on the flash • Clear configuration • Add or remove user • Change user access level Use of a SYSLOG server for monitoring network events is highly recommended.  Authentication The PowerConnect switches support authentication via a number of methods. The methods are specified
  • Dell Networking 7048 | Release Notes - Page 15
    /M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes The IAS database can be downloaded to the switch using the "ias-users" target in the copy command. The ias-users file takes the form of a configuration script, as follows: configure aaa ias-user username client-1 password my-password1
  • Dell Networking 7048 | Release Notes - Page 16
    differences from previous releases of firmware on PowerConnect switches, e.g. the 8132/8164/8132F/8164F/7024/7048/7024P/7048P/7024F/7048R/7048R-RA/M6348/M6220/M8024/8024/8024F/M8024-k switches. Dell PowerConnect series switches closely conform to networking industry standard operational capabilities
  • Dell Networking 7048 | Release Notes - Page 17
    576 phones for the PowerConnect 7024/7048/7024P/7048P/7024F switches. Release 4.2.0.4  LAG Limits Ports can be formed into LAGs in a more flexible manner. The system supports up to 128 total LAGs. Up to 144 ports can be assigned to dynamic LAGs. Up to 72 LAGs can be configured as dynamic. A LAG may
  • Dell Networking 7048 | Release Notes - Page 18
    0. The service port is still addressed using the out-of-band keyword.  Management VLAN Deprecated The PowerConnect series switches do not have an in-band management VLAN by default. Administrators can designate a VLAN for support of in-band management operations.  VLAN interface configuration mode
  • Dell Networking 7048 | Release Notes - Page 19
    8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes  Spanning Tree Changes Administrators may assign more than 1024 VLANs to MSTP instances. Only VLANs that are configured on the switch will forward traffic. The PowerConnect switches implements the 802.1Q-2005
  • Dell Networking 7048 | Release Notes - Page 20
    , this restriction makes it more difficult to troubleshoot network connectivity problems. This capability adds support for responding to pings by the VRRP master, but does not allow the VRRP Master to accept other types of packets. A configuration option controls whether the router responds to Echo
  • Dell Networking 7048 | Release Notes - Page 21
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes The operator has the ability to enable DHCP Relay Information Options both globally and on a physical interface. The interface configuration overrides the global
  • Dell Networking 7048 | Release Notes - Page 22
    in the running config. By default, auto-install supports image downgrade for network installs, specific version USB installs (using a .setup file), and stack firmware synchronization. A comprehensible message and recommendation is issued when configuring multiple services (telnet, http, etc.) to
  • Dell Networking 7048 | Release Notes - Page 23
    /7048P/7024F/7048R/7048R-RA Release Notes The PowerConnect M8024-k is the only modular switch that defaults to the simple mode of operation. Simple mode contains a restricted set of commands suitable for control of a port aggregation device that can be deployed in a network without requiring updates
  • Dell Networking 7048 | Release Notes - Page 24
    with network address. When a subnet IP is set as SNMP community IP address then snmp requests from hosts of that subnet are not accepted on the box. Get the mask from the community IP address configured and set it instead of the hard coded value. All 5.0 supported platforms Switch service tag
  • Dell Networking 7048 | Release Notes - Page 25
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes VLAN ACL blocks traffic across stack members Power supply logging 'no ipv4 or ipv6 address found in response for request id' error phone port configuration macro
  • Dell Networking 7048 | Release Notes - Page 26
    a stack of M8024-k switches from the stack view web page. The user could not see the configuration of the hold-count parameter. The user may be able to configure an invalid spanning tree port priority in range mode. The user could not reset the excluded keywords to the factory default of no excluded
  • Dell Networking 7048 | Release Notes - Page 27
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Configuration command "logging " accepts more than 63 characters. dot1dTpPortMa xInfo is displaying maximum frame size that includes MAC header. If a user
  • Dell Networking 7048 | Release Notes - Page 28
    Dell Easy Setup Wizard The default gateway would not be shown on executing "show ip route configured" The user would supported platforms All 4.2 supported platforms All 4.2 supported platforms All 4.2 supported platforms All 4.2 supported platforms All 4.2 supported platforms 26 System Firmware
  • Dell Networking 7048 | Release Notes - Page 29
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes In stacking environment, "show system temperature" command output is corrupted Error message for port enable / disable on IE on 8024F combo ports
  • Dell Networking 7048 | Release Notes - Page 30
    switch. switch reboots randomly Corrected memory initialization problem Corrected unit number range check. Corrected ARP reply policy problem Corrected power LED element id name problem which was causing this display problem. Corrected jumbo Ping packet problem. Corrected port configuration timing
  • Dell Networking 7048 | Release Notes - Page 31
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Walk of agentDaiVlanSt atsTable returns statistics for all the 4096 VLANs OOB interface configured with default IP via Setup Wizard though not to do so Unable to create VLAN ID
  • Dell Networking 7048 | Release Notes - Page 32
    that the default VLAN cannot be renamed (same as a Cisco switch). Corrected the allocation of LLDP-MED Location TLVs. Corrected error check when using invalid testing options. Corrected initialization of serial connection. Corrected problem for IE9. Corrected check of enabled VLAN. Updated error
  • Dell Networking 7048 | Release Notes - Page 33
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes "ip http secureserver" command not getting migrated from 4.1.0.19 build to 4.2.1.3 build. Data loop in Simple mode when adding VLAN ip http secure-server command not
  • Dell Networking 7048 | Release Notes - Page 34
    dot1x users" command. Corrected the issue. Corrected the retrieval of the configured value All 4.2 supported platforms All 4.2 supported platforms All 4.2 supported platforms Firmware won't allow domain names with hyphen "-" in logging email Internal ports are up during most of the switch POST
  • Dell Networking 7048 | Release Notes - Page 35
    -config" command shows the detailed switchport configuration before the switchport mode. This caused problems with some scripts. Corrected the order of running- All 4.2 supported configuration output. platforms Release 4.2.0.4 Summary PowerConnect sFlow implementation is not per specification
  • Dell Networking 7048 | Release Notes - Page 36
    user changes VLAN membership configuration on trunk port via the WEB he loses ports configuration on access ports and access ports are put into default vlan traffic. Switch hangs and needs a hard reboot. 8024 copper ports negotiate to 100M FD. The web stack display has been updated to accurately
  • Dell Networking 7048 | Release Notes - Page 37
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes No message logged for "Max number of SSH login sessions exceeded" CLI command "show ipv6 interface" does not paginate correctly 2nd and
  • Dell Networking 7048 | Release Notes - Page 38
    wait ... Corrected stored config All 4.2 supported platforms ******* The following lines in "startupconfig" failed: ******* Line 57:: no passive-interface Vl32 Web GUI Admin Duplex setting on 10G Fiber ports Switching-->Port-->Port Configuration Select a ten gigabit interface Te1/0/1 and
  • Dell Networking 7048 | Release Notes - Page 39
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release thus, the ip, icmp traffic was not working between ports as well. Issue with switch upgrade has been resolved. All 4.2 supported platforms System Firmware Version 5.1.0.1
  • Dell Networking 7048 | Release Notes - Page 40
    as part of a network change they wanted to remove a VLAN routing interface that was no longer in use. When they removed the IP address from this VLAN, they lost routing across the entire switch. SNMP MIB walk crashes switch. On the web GUI-->system-->management security-->password management, If the
  • Dell Networking 7048 | Release Notes - Page 41
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Auto-neg option via Web UI is not grayed out for 10Gb fiber ports. Auto-neg is an option in the port configuration via Web UI for 10Gb fiber ports. Ideally the auto-neg
  • Dell Networking 7048 | Release Notes - Page 42
    instead of "active" Correct interoperability problem between the PHY and the switching core. Corrected register problem when accessing the SPF+ ports Increased VRRP routing instances table. Add warning message in case offered IP address is conflicting with the configured one on another port Correct
  • Dell Networking 7048 | Release Notes - Page 43
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Summary IP PIMSM to be lost across the entire switch. PIM Join messages using wrong RP Address When network re-configuration happens, the multicast traffic may not
  • Dell Networking 7048 | Release Notes - Page 44
    Switch should have FC enabled by default "no enable authentication" does not disable access to privileged EXEC over the telnet line If LAG port is configured problem. Corrected terminal length configuration handling. Corrected "clear config" internal message error. Corrected error in Radius user
  • Dell Networking 7048 | Release Notes - Page 45
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Summary User Impact Need to change message on console when try to downgrade anything below 4.1.0.19 release for new DDR If a switch contains new DDR, downgrading to
  • Dell Networking 7048 | Release Notes - Page 46
    exceeded" VLAN web page not updating. When the full range of VLAN instances is assigned to a MST region the switch crashes. Using the config wizard to setup the PC8024 causes iSCSI error messages. The 'ip ssh protocol 2' is not being included in the running configuration. Some internal links on the
  • Dell Networking 7048 | Release Notes - Page 47
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Summary No password min length error when using web GUI. MIB walk crashes switch. Unable to deselect VLAN tags in web GUI. Access is allowed to files on the switch
  • Dell Networking 7048 | Release Notes - Page 48
    data if no changes have been made The PowerConnect switch runs the RFC3918 test without crashing The no key command is implemented to return the key configuration to the default. Passwords can be enclosed in quotes (contain embedded blanks). A password may not contain a quote. The accepted character
  • Dell Networking 7048 | Release Notes - Page 49
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Summary User Impact DHCPv6 web issues Potential operator confusion regarding switch configuration. LLDP MED application should not allow configuration of location
  • Dell Networking 7048 | Release Notes - Page 50
    default age-out time, when both FDB and MFDB tables are full. Potential operator confusion over switch operations. DHCP packets forwarding is not proper to/from the trusted and un-trusted ports Incorrect operational state in network. Configuring shared resource. The user is continually sending
  • Dell Networking 7048 | Release Notes - Page 51
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Summary User Impact LLDP-Med TLV information not registered for jumbo frame sizes greater than 8000 VLAN binding entries are not being displayed on Read-Only mode user
  • Dell Networking 7048 | Release Notes - Page 52
    -Description TLV Potential operator confusion over switch operations. Inability to diagnose network issues. Management ACL list needs "Match every packet" option Potential operator frustration over switch configuration. Possible security issue. SNMP support for Dell-LANTRAP-MIB Simple mode BPDU
  • Dell Networking 7048 | Release Notes - Page 53
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Summary User Impact LACP not working with Juniper EX-4200, show inactive port channel state. System is sending oversize (132 bytes) LACP PDUs. Stack splits into
  • Dell Networking 7048 | Release Notes - Page 54
    limit back to the default value and take other steps to correct or mitigate the underlying network issue directly. show system internal pktmgr internal control sw-rate-limit Note: This command is not available on the PCM6220 switch. The show command is to display the configured CPU rate limit for
  • Dell Networking 7048 | Release Notes - Page 55
    applied to HW. If level is not used the default rate is 5. The VLAN name command has been migrated to VLAN Config mode and is no longer available in interface VLAN mode. Release 4.2.0.4  Please refer Dell PowerConnect CLI Reference Guide for more details System Firmware Version 5.1.0.1 Page 53
  • Dell Networking 7048 | Release Notes - Page 56
    Release 4.1.1.9  No Updates Release 4.1.0.19 The following commands are supported on switches that have combo ports: Command media-type Syntax: media-type Default Configuration: N/A Description: Display the configured and active media type for the combo ports 54 System Firmware Version 5.1.0.1
  • Dell Networking 7048 | Release Notes - Page 57
    to migrate configurations from previous releases of Dell PowerConnect firmware to the 4.0.0.6 Dell PowerConnect firmware. The following table lists issues found in the CLI Reference Guide after publication: Command show service-policy in show copper-ports cablelength Issue The supported syntax is
  • Dell Networking 7048 | Release Notes - Page 58
    is occurring in the network. If problems with L2, L3 or multicast learning occur after changing this value, set the rate limit back to the default value and take other steps to correct or mitigate the underlying network issue directly. See the CLI Reference Guide updates section of this document
  • Dell Networking 7048 | Release Notes - Page 59
    /7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Release 4.2.2.3  No Updates Release 4.2.1.3  Please refer Dell PowerConnect Users Guide for more details Release 4.2.0.4  Please refer Dell PowerConnect Users Guide for more details Release 4.1.1.9  No Updates Release 4.1.0.19 The default
  • Dell Networking 7048 | Release Notes - Page 60
    users [username]" command seems to have been deprecated even though it still exists in the CLI guide. PowerConnect 7048 switches that are setup to send email alerts for log messages at the default the configuration for pre-provisioned ports but when the stack is reloaded the configuration for these
  • Dell Networking 7048 | Release Notes - Page 61
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Release 5.0.0.4 Summary QSFP Base CR4 with copper DAC cable lengths greater than 3 meters will not work on PC8100 switches User Impact When using the DAC copper cables
  • Dell Networking 7048 | Release Notes - Page 62
    support" command with UDLD and MSTP configured: "ATP RX: Failed to alloc" logs On PC8100 switches the switch or user, just downloaded back to the switch if switch and PC are located in different networks and the networks User to have to retry the download or change the IP address or VLANs on the switch
  • Dell Networking 7048 | Release Notes - Page 63
    /7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Summary Port goes down if the port is excluded from native vlan with UDLD feature enabled on it. SNMP V3 walk may fail after "initiate failover" command is issued. OOB static IP entry cannot be the same as the DHCP assigned IP address User
  • Dell Networking 7048 | Release Notes - Page 64
    Failure to follow these instructions may cause units to crash when booted into the 4.1 firmware. To recover the switch, attach a serial cable and enter the boot menu (press 2 - Start Boot Menu at the prompt). From the boot menu, select 10 - Restore configuration to factory defaults, and then select
  • Dell Networking 7048 | Release Notes - Page 65
    to the user. None Use any other form of dot1x authentication. None None None M8024-k Internal ports are up during most of the switch POST M8024, M6220, M8024k, PC8024F Extra Lines and Tabs in CSR Cause CA Submittal Troubles Sflow configurations do not get saved to the config Network operators may
  • Dell Networking 7048 | Release Notes - Page 66
    GUI sFlow configuration , receiver owner inconsistent with CLI User Impact Operator may become confused regarding switch operations. Operators using IE 8 may experience issues as follows: (1) Status LED does not glow to identify Master (2) Member units do not show "DELL PowerConnect M8024-k" model
  • Dell Networking 7048 | Release Notes - Page 67
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Release 4.1.1.9 Summary LLPF is not supported on the PCM6220 switch configurations Trunk mode VLANs transmit tagged frames only User and data service for duration of
  • Dell Networking 7048 | Release Notes - Page 68
    mode. In this case, an invalid configuration file was downloaded (on purpose) via the web. When the switch rebooted, it detected that the configuration file was invalid and overwrote the start-up config with the default configuration (an empty configuration). Users are advised to maintain off-line
  • Dell Networking 7048 | Release Notes - Page 69
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes Known Restrictions and Limitations Release 5.1.0.1 Description SNMP walk is not successful while doing walk on root port User Impact Low SNMP walk on root port may
  • Dell Networking 7048 | Release Notes - Page 70
    detected or an IEEE length check error User Impact Low For typical IP networks this problem won't be seen because the length field/Ethertype will contain a valid value. Web Description The device manager GUI does not support IE9 at this time. User Impact Moderate - Multiple errors are displayed
  • Dell Networking 7048 | Release Notes - Page 71
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R Broadcom NIC 57810S never reports to the internal switch that the link is down because it needs configurable traffic classes is 7. User Impact Low Workaround: 1. In Control Panel  Network
  • Dell Networking 7048 | Release Notes - Page 72
    IPv6 Fragmentation Support User Impact Operators may see jumbo packets discarded when operating in a routed IP environment. Administrators are advised when operating in a L3 routing configuration with jumbo frames to adjust both the link MTU and the VLAN IP MTU. User Impact The switch is not
  • Dell Networking 7048 | Release Notes - Page 73
    PowerConnect 8132/8164/8132F/8164F/8024/8024F/M8024/M8024-k/ M6220/M6348/7024/7048/7024P/7048P/7024F/7048R/7048R-RA Release Notes VRRP Description The maximum number of VRRP instances is 50. system automatically adjust the IPv4/ IPv6 MTU based on the link MTU. User Impact Users can scale VRRP
  • Dell Networking 7048 | Release Notes - Page 74
    VLANs. In this case, the default VLAN (1) and the configured FCoE VLAN. In general, VLAN configuration source Low - Most users prefer automatic setup of CNAs The Broadcom CNA does not support manual configuration of VLAN. This means that customers who prefer to set up their FCoE network manually
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Dell™ PowerConnect™
8132/8164/8132F/8164F/7024/7048/7024P/7048P/7024F/7048R/
7048R-RA/8024/8024F/M6220/M6348/M8024/M8024-k
PowerConnect
5.1.0.1 Firmware Release Notes
Date: April 2013
System Firmware Version 5.1.0.1
Information in this document is subject to change without notice.
© 2003 – 2013 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc.
is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo and PowerConnect are trademarks of Dell Inc; Intel and Pentium are registered trademarks and
Celeron is a trademark of Intel Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entity claiming the marks and names or their products. Dell
Inc. disclaims any proprietary interest in trademarks and trade names other than its own. All rights reserved. This document may not, in whole or
in part, be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form without the prior written
consent of Dell. Dell reserves the right to make changes without further notice to any products or specifications referred to herein to improve
reliability, functionality or design.
Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws.